TI TPS7A7300RGWR

TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
3-A, Fast-Transient, Low-Dropout Voltage Regulator
FEATURES
1
•
•
•
•
•
•
Wireless Infrastructure: SerDes, FPGA, DSP™
RF Components: VCO, ADC, DAC, LVDS
Set-Top Boxes: Amplifier, ADC, DAC, FPGA,
DSP
Wireless LAN, Bluetooth®
PCs and Printers
Audio and Visual
1.5 V
IN
The TPS7A7300 low-dropout (LDO) voltage regulator
is designed for applications seeking very-low dropout
capability (240 mV at 3A) with an input voltage from
1.5 V to 6.5 V. The TPS7A7300 offers an innovative,
user-configurable, output-voltage setting from 0.9 V to
3.5 V, eliminating external resistors and any
associated error.
The TPS7A7300 has very fast load-transient
response, is stable with ceramic output capacitors,
and supports a better than 2% accuracy over line,
load, and temperature. A soft-start pin allows for an
application to reduce inrush into the load.
Additionally, an open-drain, power-good signal allows
for sequencing power rails.
The TPS7A7300 is available in a 5-mm × 5-mm,
20-pin QFN package.
6
3
Output Current Slew Rate: 1A/µs
5
4
Output
Current
5.5V to 5.0V
3.3V to 3.0V
3.0V to 2.5V
2.5V to 1.8V
2
1.8V to 1.5V
3
2
1
Output Current (A)
APPLICATIONS
DESCRIPTION
Output Voltage (V)
• Low Dropout Voltage: 240 mV at 3A
• VIN Range: 1.5 V to 6.5 V
• Configurable Fixed VOUT Range: 0.9 V to 3.5 V
Adjustable VOUT Range: 0.9 V to 5.0 V
• Very Good Load and Line Transient Response
• Stable with Ceramic Output Capacitor
• 2% Accuracy over Line, Load, and
Temperature
• Programmable Softstart
• Power Good (PG) Output
• 5-mm × 5-mm QFN-20 Package
234
PG
1
CIN
1.5V to 1.2V
TPS7A7300
1.5V to 1.0V
0
EN
OUT
SS
CSS
SNS
FB
Optional
GND
50mV
100mV
1.2 V = 0.5 Vref
+ 100 mV
COUT + 200 mV
+ 400 mV
0
Time (100µs/div)
G312
Load Transient Response with
Seven Different Results:
1.5 VIN to 1.0 VOUT, 1.5 VIN to 1.2 VOUT,
1.8 VIN to 1.5 VOUT, 2.5 VIN to 1.8 VOUT,
3.0 VIN to 2.5 VOUT, 3.3 VIN to 3.0 VOUT,
and 5.5 VIN to 5.0 VOUT
1.6V
200mV 400mV 800mV
Typical Application
1
2
3
4
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
DSP is a trademark of Texas Instruments.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
PRODUCT
Description
TPS7A7300yyyz
(1)
YYY is package designator.
Z is package quantity.
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the
device product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating free-air temperature range (unless otherwise noted).
VALUE
Voltage
MIN
MAX
UNIT
IN, PG, EN
–0.3
+7.0
V
SS, FB, SNS, OUT
–0.3
VIN + 0.3 (2)
V
–0.3
VOUT + 0.3
V
50mV, 100mV, 200mV, 400mV, 800mV, 1.6V
OUT
Current
PG (sink current into IC)
Temperature
Electrostatic Discharge Rating (3)
(1)
(2)
(3)
2
Internally limited
A
5
mA
Operating virtual junction, TJ
–55
+150
Storage, Tstg
–55
+150
°C
2
kV
500
V
Human body model (HBM, JESD22-A114A)
Charged device model (CDM, JESD22-C101B.01)
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated is not implied. Exposure to absolutemaximum-rated conditions for extended periods may affect device reliability.
The absolute maximum rating is VIN + 0.3 V or +7.0 V, whichever is smaller.
ESD testing is performed according to the respective JESD22 JEDEC standard.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
THERMAL INFORMATION
TPS7A7300 (3)
THERMAL METRIC
(1) (2)
RGW (QFN)
UNITS
20 PINS
Junction-to-ambient thermal resistance (4)
θJA
(5)
35.7
θJCtop
Junction-to-case (top) thermal resistance
θJB
Junction-to-board thermal resistance (6)
15.2
ψJT
Junction-to-top characterization parameter (7)
0.4
ψJB
Junction-to-board characterization parameter (8)
15.4
θJCbot
Junction-to-case (bottom) thermal resistance (9)
3.8
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
33.6
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953A.
For thermal estimates of this device based on PCB copper area, see the TI PCB Thermal Calculator.
Thermal data for the RGW package is derived by thermal simulations based on JEDEC-standard methodology as specified in the
JESD51 series. The following assumptions are used in the simulations:
(a) The exposed pad is connected to the PCB ground layer through a 4 × 4 thermal via array.
(b) Both the top and bottom copper layers have a dedicated pattern for 4% copper coverage.
(c) These data were generated with only a single device at the center of a JEDEC high-K (2s2p) board with 3-inch × 3-inch copper area.
To understand the effects of the copper area on thermal performance, refer to the Power Dissipation and Estimating Junction
Temperature sections.
The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as
specified in JESD51-7, in an environment described in JESD51-2a.
The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the top of the package. No specific JEDECstandard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
The junction-to-board thermal resistance is obtained by simulating in an environment with a ring cold plate fixture to control the PCB
temperature, as described in JESD51-8.
The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted
from the simulation data to obtain θJA using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-board characterization parameter, ψJB, estimates the junction temperature of a device in a real system and is extracted
from the simulation data to obtain θJA using a procedure described in JESD51-2a (sections 6 and 7).
The junction-to-case (bottom) thermal resistance is obtained by simulating a cold plate test on the exposed (power) pad. No specific
JEDEC standard test exists, but a close description can be found in the ANSI SEMI standard G30-88.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
Over operating temperature range (TJ = –40°C to +125°C), 1.425 V ≤ VIN ≤ 6.5 V, VIN ≥ VOUT(TARGET) + 0.3 V or
VIN ≥ VOUT(TARGET) + 0.7 V (1) (2), OUT connected to 50 Ω to GND (3),VEN = 1.1 V, COUT = 10 μF, CSS = 10 nF, and PG pin pulled
up to VIN with 100 kΩ, 27 kΩ ≤ R2 ≤ 33 kΩ for adjustable configuration (4), unless otherwise noted.
Typical values are at TJ = +25°C.
PARAMETER
VIN
Input voltage range
V(SS)
SS pin voltage
TEST CONDITIONS
VOUT
Output voltage accuracy (5) (6)
Fixed with voltage setting pins
0.9
3.5
Adjustable, 25 mA ≤ IOUT ≤ 3 A
–2.0
+2.0
Fixed, 25 mA ≤ IOUT ≤ 3 A
–3.0
+3.0
IOUT = 25 mA
Load regulation
25 mA ≤ IOUT ≤ 3 A
(7)
Output current limit
0.01
V
V
%
%/V
0.1
%/A
VOUT ≤ 3.3 V, IOUT = 3 A, V(FB) = GND
240
mV
3.3 V < VOUT, IOUT = 3 A, V(FB) = GND
700
mV
4.2
A
VOUT forced at 0.9 × VOUT(TARGET), VIN = 3.3 V,
VOUT(TARGET) = 0.9 V
3.2
Full load, IOUT = 3 A
GND pin current
UNIT
V
5.0
Line regulation
I(GND)
6.5
0.9
ΔVO(ΔIO)
I(LIM)
MAX
Adjustable with external feedback resistors
ΔVO(ΔVI)
Dropout voltage
TYP
0.5
Output voltage range
V(DO)
MIN
1.425
3.7
3.7
Minimum load,
VIN = 6.5 V, VOUT(TARGET) = 0.9 V, IOUT = 25 mA
mA
4
mA
5
μA
±0.1
μA
0
0.5
V
1.1
6.5
V
0.96VOUT
V
Shutdown, PG = (open),
VIN = 6.5 V, VOUT(TARGET) = 0.9 V, V(EN) < 0.5 V
0.1
I(EN)
EN pin current
VIL(EN)
EN pin low-level input voltage
(disable device)
VIH(EN)
EN pin high-level input voltage
(enable device)
VIT(PG)
PG pin threshold
For the direction PG↓ with decreasing VOUT
Vhys(PG)
PG pin hysteresis
For PG↑
VOL(PG)
PG pin low-level output voltage
VOUT < VIT(PG), IPG = –1 mA (current into device)
Ilkg(PG)
PG pin leakage current
VOUT > VIT(PG), V(PG) = 6.5 V
I(SS)
SS pin charging current
V(SS) = GND, VIN = 3.3 V
Vn
Output noise voltage
BW = 100 Hz to 100 kHz,
VIN = 1.5 V, VOUT = 1.2 V, IOUT = 3 A
39.46
μVRMS
Tsd
Thermal shutdown temperature
Shutdown, temperature increasing
+160
°C
Reset, temperature decreasing
+140
°C
TJ
Operating junction temperature
(1)
(2)
(3)
(4)
(5)
(6)
(7)
4
VIN = 6.5 V, V(EN) = 0 V and 6.5 V
0.85VOUT
0.9VOUT
0.02VOUT
3.5
–40
5.1
V
0.4
V
1
μA
7.2
μA
+125
°C
When VOUT ≤ 3.5 V, VIN ≥ (VOUT + 0.3 V) or 1.425 V, whichever is greater; when VOUT > 3.5 V, VIN ≥ (VOUT + 0.7 V).
VOUT(TARGET) is the calculated target VOUT value from the output voltage setting pins: 50mV, 100mV, 200mV, 400mV, 800mV, and 1.6V
in fixed configuration, or the expected VOUT value set by external feedback resistors in adjustable configuration.
This 50-Ω load is disconnected when the test conditions specify an IOUT value.
R2 is the bottom-side of the feedback resistor between the FB pin and GND. See Figure 40 for details.
When the TPS7A7300 is connected to external feedback resistors at the FB pin, external resistor tolerances are not included.
The TPS7A7300 is not tested at VOUT = 0.9 V, 2.7 V ≤ VIN ≤ 6.5 V, and 500 mA ≤ IOUT ≤ 3 A because the power dissipation is higher
than the maximum rating of the package. Also, this accuracy specification does not apply on any application condition that exceeds the
power dissipation limit of the package.
V(DO) is not defined for output voltage settings below 1.2 V.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
FUNCTIONAL BLOCK DIAGRAM
Current
Limit
IN
Charge
Pump
SS
CSS
UVLO
0.5-V Reference
OUT
Thermal
Protection
PG
700-µs
Delay
1.2-V Reference
70 kΩ
Optional
0.45 V
50 kΩ
50 kΩ
SNS
32R
FB
Hysteresis
EN
320R
GND
50mV
160R
80R
40R
20R
100mV 200mV 400mV 800mV
10R
1.6V
NOTE: 320R = 1.024 MΩ (that is, 1R = 3.2 kΩ).
Figure 1. Functional Block Diagram
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
PIN CONFIGURATIONS
OUT
OUT
GND
IN
IN
20
19
18
17
16
RGW PACKAGE
5-mm × 5-mm QFN-20
(TOP VIEW)
OUT
1
15
IN
SNS
2
14
EN
FB
3
13
SS
PG
4
12
NC
50mV
5
11
1.6V
10
800mV
8
GND
9
7
200mV
400mV
6
100mV
Thermal Pad
PIN DESCRIPTIONS
NAME
50mV,
100mV,
200mV,
400mV,
800mV,
1.6V
RGW
Output voltage setting pins. These pins should be connected to ground or left floating. Connecting these pins to
5, 6, 7, ground increases the output voltage by the value of the pin name; multiple pins can be simultaneously connected to
9, 10, 11 GND to select the desired output voltage. Leave these pins floating (open) when not in use. See the USERCONFIGURABLE OUTPUT VOLTAGE section for more details.
EN
14
Enable pin. Driving this pin to logic high enables the device; driving the pin to logic low disables the device. See the
ENABLE AND SHUTDOWN THE DEVICE section for more details.
FB
3
Output voltage feedback pin. Connected to the error amplifier. See the USER-CONFIGURABLE OUTPUT VOLTAGE
and TRADITIONAL ADJUSTABLE CONFIGURATION sections for more details.
GND
8, 18
IN
15, 16,
17
NC
12
OUT
1, 19, 20
PG
4
Active-high power good pin. An open-drain output that indicates when the output voltage reaches 90% of the target.
See POWER GOOD for more details.
SNS
2
Output voltage sense input pin. See the USER-CONFIGURABLE OUTPUT VOLTAGE and TRADITIONAL
ADJUSTABLE CONFIGURATION sections for more details.
SS
13
Soft-start pin. Leaving this pin open provides soft-start of the default setting.
Connecting an external capacitor between this pin and the ground enables the soft-start function by forming an RCdelay circuit in combination with the integrated resistance on the silicon. See the SOFT-START section for more
details.
Thermal Pad
6
DESCRIPTION
Ground pin.
Unregulated supply voltage pin. It is recommended to connect an input capacitor to this pin. See INPUT
CAPACITOR REQUIREMENTS for more details.
Not internally connected. The NC pin is not connected to any electrical node. It is strongly recommended to connect
this pin and the thermal pad to a large-area ground plane. See the Power Dissipation section for more details.
Regulated output pin. A 4.7-μF or larger capacitance is required for stability. See OUTPUT CAPACITOR
REQUIREMENTS for more details.
It is strongly recommended to connect the thermal pad to a large-area ground plane. If available, connect an
electrically-floating, dedicated thermal plane to the thermal pad as well.
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
LOAD REGULATION
(0.9 V, Adjustable)
0.927
0.909
Y−axis scale is 1%Vout/div
Y−axis scale is 1%Vout/div
5.1
Output Voltage (V)
Output Voltage (V)
5.15
− 40°C
0°C
25°C
85°C
105°C
125°C
0.918
LOAD REGULATION
(5.0 V, Adjustable)
0.9
0.891
0.882
0.873
0.5
1
1.5
2
Output Current (A)
2.5
5
− 40°C
0°C
25°C
85°C
105°C
125°C
4.95
4.9
VIN = 1.425 V
R1 = 24.1 kΩ, R2 = 30.1 kΩ
0
5.05
4.85
3
0
Figure 3.
LOAD REGULATION
(0.9 V, Fixed by Setting Pins)
LOAD REGULATION
(3.5 V, Fixed by Setting Pins)
3.605
− 40°C
0°C
25°C
85°C
105°C
125°C
3.57
Output Voltage (V)
Output Voltage (V)
0.918
0.909
0.9
0.873
− 40°C
0°C
25°C
85°C
105°C
125°C
0
0.5
VIN = 1.425 V
VOUT(TARGET) = 0.9 V
400mV pin to GND; 50mV, 100mV
200mV, 800mV, 1.6V pins open
1
1.5
2
Output Current (A)
2.5
3.535
250
0
0.5
1
G202
VIN = 1.5 V
FB = GND
50
300
250
1.5
2
Output Current (A)
Figure 6.
Copyright © 2012, Texas Instruments Incorporated
G205
200
150
100
IOUT = 3 A
FB = GND and plot VIN − VOUT
50
1
3
− 40°C
0°C
25°C
85°C
105°C
125°C
350
100
0.5
2.5
DROPOUT VOLTAGE vs TEMPERATURE
150
0
1.5
2
Output Current (A)
Figure 5.
200
0
VIN = 3.8 V
VOUT(TARGET) = 3.5 V
200mV, 400mV, 800mV, 1.6V pins
to GND; 50mV, 100mV pins open
Y−axis scale is 1%Vout/div
3.395
3
Dropout Voltage (mV)
Dropout Voltage (mV)
300
G005
3.43
400
− 40°C
0°C
25°C
85°C
105°C
125°C
3
3.465
DROPOUT VOLTAGE vs OUTPUT CURRENT
350
2.5
3.5
Figure 4.
400
1.5
2
Output Current (A)
Figure 2.
Y−axis scale is 1%Vout/div
0.882
1
G002
0.927
0.891
0.5
VIN = 5.3 V
R1 = 271 kΩ, R2 = 30.1 kΩ
2.5
3
G012
0
1
2
3
4
Input Voltage (V)
5
5.5
G015
Figure 7.
Submit Documentation Feedback
7
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
LINE REGULATION
(0.9 V, Adjustable)
0.927
0.909
Y−axis scale is 1%Vout/div
Y−axis scale is 1%Vout/div
5.1
Output Voltage (V)
Output Voltage (V)
5.15
− 40°C
0°C
25°C
85°C
105°C
125°C
0.918
LINE REGULATION
(5.0 V, Adjustable)
0.9
0.891
0.882
0.873
1.5
2
2.5
3 3.5 4 4.5
Input Voltage (V)
5
5.5
6
5
− 40°C
0°C
25°C
85°C
105°C
125°C
4.95
4.9
IOUT = 25 mA
R1 = 24.1 kΩ, R2 = 30.1 kΩ
1
5.05
4.85
6.5
5
LINE REGULATION
(0.9 V, Fixed by Setting Pins)
LINE REGULATION
(3.5 V, Fixed by Setting Pins)
3.605
− 40°C
0°C
25°C
85°C
105°C
125°C
Output Voltage (V)
Output Voltage (V)
3.57
0.909
0.9
− 40°C
0°C
25°C
85°C
105°C
125°C
1
1.5
2
IOUT = 25 mA
VOUT(TARGET) = 0.9 V
400mV pin to GND; 50mV, 100mV
200mV, 800mV, 1.6V pins open
2.5
3 3.5 4 4.5
Input Voltage (V)
5
5.5
6
3.465
3.395
6.5
5
5.5
6
Input Voltage (V)
G206
6.5
G207
Figure 10.
Figure 11.
OUTPUT VOLTAGE:
ACTUAL vs PIN-SETTING
OUTPUT VOLTAGE:
ACTUAL (Normalized) vs PIN-SETTING
1
Error in Actual Output Voltage (%)
Actual Output Voltage (V)
3.5
Y−axis scale is 1%Vout/div
3.2
2.8
2.4
2
1.6
1.2
VIN = 4 V
IOUT = 50 mA
1.2
1.6
2
2.4
VOUT(TARGET) (V)
Figure 12.
8
3.535
IOUT = 25 mA
VOUT(TARGET) = 3.5 V
200mV, 400mV, 800mV, 1.6V pins
to GND; 50mV, 100mV pins open
3.43
3.6
0.8
0.8
G007
Figure 9.
0.918
0.873
6.5
Figure 8.
Y−axis scale is 1%Vout/div
0.882
5.5
6
Input Voltage (V)
G006
0.927
0.891
IOUT = 25 mA
R1 = 271 kΩ, R2 = 30.1 kΩ
Submit Documentation Feedback
2.8
3.2
3.6
G020
0.8
0.6
0.4
0.2
0
−0.2
−0.4
−0.6
VIN = 4 V
IOUT = 50 mA
−0.8
−1
0.8
1.2
1.6
2
2.4
VOUT(TARGET) (V)
2.8
3.2
3.6
G021
Figure 13.
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
GND PIN CURRENT vs OUTPUT CURRENT
− 40°C
0°C
25°C
85°C
105°C
125°C
Ground Current (mA)
4
3
2
VIN = 1.8 V
VOUT(TARGET) = 1.5 V
200mV, 800mV pins to GND
50mV, 100mV, 200mV, 400mV
pins open
0
0.5
1
1.5
2
Output Current (A)
2.5
2
0
3
1
2
3
5.5
G033
4
3
2
VIN = 4 V
VOUT(TARGET) = 3.5 V
200mV, 400mV, 800mV, 1.6V pins to GND
50mV, 100mV pins open
1
2
6.5
5
1
1.5
6
EN = GND
50−Ω resistor between OUT and GND
2
2.5
3 3.5 4 4.5
Input Voltage (V)
5
5.5
6
0
6.5
0
G032
1
1.5
2
2.5
Forced Output Voltage (V)
3
3.5
G042
POWER-GOOD PIN DRIVE CAPABILITY
1
VOUT(TARGET) = 1.2 V
100mV, 200mV, 400mV pins to GND
50mV, 800mV, 1.6V pins open
50−Ω resistor between OUT and GND
VIN = 1.5 V, − 40 °C
VIN = 1.5 V, 25 °C
VIN = 1.5 V, 125 °C
VIN = 6.5 V, − 40 °C
VIN = 1.5 V, 25 °C
VIN = 1.5 V, 125 °C
0.8
PG Pin Voltage (V)
VIN=1.5V
VIN=6.5V
0.5
Figure 17.
POWER-GOOD THRESHOLD VOLTAGE
vs TEMPERATURE
94
93
92
91
90
89
88
87
86
85
84
−50
5
CURRENT LIMIT
vs OUTPUT VOLTAGE (Foldback)
4
96
95
3 3.5 4 4.5
Input Voltage (V)
GND PIN CURRENT IN SHUTDOWN
vs TEMPERATURE
− 40°C
0°C
25°C
85°C
105°C
125°C
1
2.5
Figure 15.
Figure 16.
Threshould Voltage (%VOUT)
1.5
G031
Figure 14.
5
0
3
IOUT = 25 mA
VOUT(TARGET) = 0.9 V
400mV pin to GND; 50mV, 100mV
200mV, 800mV, 1.6V pins open
1
Current Limit (A)
0
− 40°C
0°C
25°C
85°C
105°C
125°C
4
1
Shutdown Ground Current (µA)
GND PIN CURRENT vs INPUT VOLTAGE
5
Ground Current (mA)
5
0.6
VOUT(TARGET) = 1.2 V
100mV, 200mV, 400mV
pins to GND
50mV, 800mV, 1.6V
pins open
50−Ω resistor
from OUT to GND
Spec limit defined at 1−mA.
0.4
0.2
−25
0
25
50
Temperature (°C)
Figure 18.
Copyright © 2012, Texas Instruments Incorporated
75
100
125
G050
0
0
0.5
1
1.5
Forced PG Pin Current (mA)
2
G051
Figure 19.
Submit Documentation Feedback
9
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
NOISE SPECTRAL DENSITY BY EXTERNAL CAPACITORS
10
Output Spectral Noise Density (µV/ Hz)
Output Spectral Noise Density (µV/ Hz)
NOISE SPECTRAL DENSITY BY OUTPUT VOLTAGE
VOUT(TARGET) = 0.9 V
VOUT(TARGET) = 1.2 V
VOUT(TARGET) = 3.3 V
1
VIN = VOUT(TARGET) + 0.3 V
IOUT = 3 A
100 Hz to 100 kHz RMS Noise
0.9 V: 38.88 µVRMS
1.2 V: 39.46 µVRMS
3.3 V: 75.59 µVRMS
0.1
0.01
10
100
1k
Frequency (Hz)
10k
100k
10
VIN = 1.8 V, IOUT = 1 A
VOUT(TARGET) = 1.5 V
200mV, 800mV pins to GND
50mV, 100mV, 400mV, 1.6V pins open
1
CSS = 100nF, COUT = 100µF
CSS = 100nF, COUT = 10µF
CSS = 10nF, COUT = 100µF
CSS = 10nF, COUT = 10µF
CSS = 1nF, COUT = 100µF
CSS = 1nF, COUT = 10µF
0.1
0.01
10
100
1k
Frequency (Hz)
G062
Figure 20.
10k
100k
G063
Figure 21.
POWER-SUPPLY RIPPLE REJECTION
vs FREQUENCY
100
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
90
80
PSRR (dB)
70
VIN=3.8V, IOUT=0.1A VIN=3.6V, IOUT=0.1A
60
50
40
30
VIN=3.6V, IOUT=3A
20
10
0
VIN=3.8V, IOUT=3A
10
100
1k
10k
100k
Frequency (Hz)
1M
10M
G072
Figure 22.
10
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
LOAD TRANSIENT RESPONSE
(VOUT = 1.2 V)
1.2
6
4
Output Voltage
1.1
2
8
Output Current Slew Rate: 1A/µs
VOUT(TARGET)=3.3V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
3.4
3.3
4
Output Voltage
3.2
2
Output
Current
Output
Current
1
0
Time (100µs/div)
3.1
0
Time (100µs/div)
G315
Figure 23.
LINE TRANSIENT RESPONSE
POWER-UP/POWER-DOWN (IN = EN)
Voltage (V)
VIN
4
Voltage (V)
IOUT=1A,
VOUT(TARGET)=3.3V
400mV, 800mV, 1.6V
pins to GND
50mV, 100mV, 200mV
pins open
4.2
3.8
3.6
VOUT
3.4
3.2
Time (20 µs/div)
7
6.5
6
5.5
5
4.5
4
3.5
3
2.5
2
1.5
1
0.5
0
VIN
VOUT
Time (2 ms/div)
G300
TURN-ON RESPONSE (IN = EN)
TURN-OFF RESPONSE (IN = EN)
5
4.5
4
4
VIN
3.5
Voltage (V)
Voltage (V)
IN = EN
50−Ω resistor from OUT to GND
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
4.5
VIN
3.5
3
2.5
VOUT
2
0.5
G301
Figure 26.
5
1
VOUT(TARGET)=3.3V
400mV, 800mV,
1.6V pins to GND
50mV, 100mV,
200mV pins open
50−Ω resistor between
OUT and GND
Figure 25.
1.5
G318
Figure 24.
4.6
4.4
6
Output Current (A)
1.3
3.5
Output Voltage (V)
8
Output Current Slew Rate: 1A/µs
VOUT(TARGET)=1.2V
100mV, 200mV, 400mV
pins to GND
50mV, 800mV, 1.6V pins open
Output Current (A)
Output Voltage (V)
1.4
LOAD TRANSIENT RESPONSE
(VOUT = 3.3 V)
IN = EN
50−Ω resistor from OUT to GND
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
3
2.5
2
VOUT
1.5
1
0.5
0
0
Time (1 ms/div)
Figure 27.
Copyright © 2012, Texas Instruments Incorporated
G302
Time (1 ms/div)
G303
Figure 28.
Submit Documentation Feedback
11
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TJ = +25°C, VIN = VOUT(TARGET) + 0.3 V, IOUT = 25 mA, V(EN) = VIN, CIN = 10 μF, COUT = 10 μF, C(SS) = 10 nF, and the PG pin
pulled up to VIN with 100-kΩ pull-up resistor, unless otherwise noted.
EN PULSE ON RESPONSE
(Over Stable VIN)
EN PULSE OFF RESPONSE
(Over Stable VIN)
5
5
4.5
4.5
VOUT
VIN
4
3.5
3
Voltage (V)
3.5
Voltage (V)
VIN
4
VEN
2.5
2
1.5
0.5
VOUT
VEN
2
50−Ω resistor from OUT to GND
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
1.5
50−Ω resistor from OUT to GND
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
1
3
2.5
1
0.5
0
0
Time (1 ms/div)
Time (1 ms/div)
G304
Figure 29.
SOFT-START DELAY vs CSS (Enlarged View)
SOFT-START DELAY vs CSS (Reduced View)
5
5
VOUT (CSS=0F)
4.5
4
VIN
VOUT(TARGET) = 3.3 V
50−Ω resistor from OUT to GND
4.5
4
VIN
VOUT (CSS=0F)
3.5
Voltage (V)
Voltage (V)
3.5
3
2.5
G305
Figure 30.
VEN
VOUT (CSS=10nF)
2
VOUT (CSS=100nF)
1.5
3
2.5
VOUT (CSS=10nF)
VEN
VOUT (CSS=100nF)
2
1.5
1
VOUT (CSS=1µF)
1
VOUT (CSS=1µF)
0.5
VOUT(TARGET) = 3.3 V
50−Ω resistor from OUT to GND
0.5
0
0
Time (5 ms/div)
Time (50 ms/div)
G306
Figure 31.
SOFT-START DELAY vs CSS
1000
Softstart Delay (ms)
G307
Figure 32.
0%VOUT to 90%VOUT
50−Ω resistor from OUT to GND
VOUT(TARGET) = 3.3 V
400mV, 800mV, 1.6V pins to GND
50mV, 100mV, 200mV pins open
100
10
1
0.1
1
10
100
CSS (nF)
1000
G308
Figure 33.
12
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
APPLICATION INFORMATION
OVERVIEW
The TPS7A7300 belongs to a family of new-generation LDO regulators that uses innovative circuitry to offer
very-low dropout voltage along with the flexibility of a programmable output voltage.
The dropout voltage for this LDO regulator family is 0.24 V at 3 A. This voltage is ideal for making the
TPS7A7300 into a point-of-load (POL) regulator because 0.24 V at 3 A is lower than any voltage gap among the
most common voltage rails: 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.0 V, and 3.3 V. This device offers a fully userconfigurable output voltage setting method. The TPS7A7300 output voltage can be programmed to any target
value from 0.9 V to 3.5 V in 50-mV steps.
Another big advantage of using the TPS7A7300 is the wide range of available operating input voltages: from 1.5
V to 6.5 V. The TPS7A7300 also has very good line and load transient response. All these features allow the
TPS7A7300 to meet most voltage-regulator needs for under-6-V applications, using only one device so that less
time is spent on inventory control.
Texas Instruments also offers different output current ratings with other family devices: the TPS7A7100 (1 A) and
TPS7A7200 (2 A).
USER-CONFIGURABLE OUTPUT VOLTAGE
IN
IN
GND
OUT
OUT
IN
IN
GND
OUT
OUT
Unlike traditional LDO devices, the TPS7A7300 comes with only one orderable part number; there is no
adjustable or fixed output voltage option. The output voltage of the TPS7A7300 is selectable in accordance with
the names given to the output voltage setting pins: 50mV, 100mV, 200mV, 400mV, 800mV, and 1.6V. For each
pin connected to the ground, the output voltage setting increases by the value associated with that pin name,
starting from the value of the reference voltage of 0.5 V; floating the pin(s) has no effect on the output voltage.
Figure 34 through Figure 39 show examples how to program the output voltages.
OUT
IN
OUT
IN
SNS
EN
SNS
EN
FB
SS
FB
SS
PG
NC
PG
NC
Thermal Pad
Thermal Pad
1.6V
1.6V
Optional
800mV
GND
400mV
100mV
200mV
50mV
Optional
800mV
GND
400mV
200mV
100mV
50mV
VIN
VIN
FB
FB
OUT
OUT
SNS
SNS
0.5 V
0.5 V
3.2R
3.2R
FB
FB
32R
16R
8R
4R
2R
1R
32R
16R
8R
4R
2R
1R
50mV
100mV
200mV
400mV
800mV
1.6V
50mV
100mV
200mV
400mV
800mV
1.6V
VOUT = 0.9 V = 0.5 V + 400 mV
0.5 V is Vref
VOUT = 0.5 V ´ (1 + 3.2R/4R)
Figure 34. 0.9-V Configuration
Copyright © 2012, Texas Instruments Incorporated
VOUT = 1.2 V = 0.5 V + 100 mV + 200 mV + 400 mV
0.5 V is Vref
VOUT = 0.5 V ´ (1 + 3.2R/2.29R)
2.29R is parallel resistance of 16R, 8R, and 4R.
Figure 35. 1.2-V Configuration
Submit Documentation Feedback
13
TPS7A7300
IN
IN
GND
OUT
OUT
IN
www.ti.com
IN
GND
OUT
OUT
SBVS190B – MARCH 2012 – REVISED APRIL 2012
OUT
IN
OUT
IN
SNS
EN
SNS
EN
FB
SS
FB
SS
PG
NC
PG
NC
Thermal Pad
Thermal Pad
1.6V
1.6V
Optional
800mV
GND
400mV
100mV
200mV
50mV
Optional
800mV
GND
400mV
200mV
100mV
50mV
VIN
VIN
FB
FB
OUT
OUT
SNS
SNS
0.5 V
0.5 V
3.2R
3.2R
FB
FB
32R
16R
8R
4R
2R
1R
32R
16R
8R
4R
2R
1R
50mV
100mV
200mV
400mV
800mV
1.6V
50mV
100mV
200mV
400mV
800mV
1.6V
VOUT = 1.8 V = 0.5 V + 100 mV + 400 mV + 800 mV
VOUT = 2.5 V = 0.5 V + 400 mV + 1.6 V
0.5 V is Vref
0.5 V is Vref
1.23R is parallel resistance of 16R, 4R, and 2R.
VOUT = 0.5 V ´ (1 + 3.2R/0.8R)
0.8R is parallel resistance of 4R and 1R.
IN
IN
GND
OUT
Figure 37. 2.5-V Configuration
IN
IN
GND
OUT
OUT
Figure 36. 1.8-V Configuration
OUT
VOUT = 0.5 V ´ (1 + 3.2R/1.23R)
OUT
IN
OUT
IN
SNS
EN
SNS
EN
FB
SS
FB
SS
PG
NC
PG
NC
Thermal Pad
Thermal Pad
1.6V
1.6V
Optional
800mV
GND
400mV
100mV
200mV
50mV
Optional
800mV
GND
400mV
200mV
100mV
50mV
VIN
VIN
FB
FB
OUT
OUT
SNS
SNS
0.5 V
0.5 V
3.2R
3.2R
FB
16R
8R
4R
2R
1R
32R
16R
8R
4R
2R
1R
50mV
100mV
200mV
400mV
800mV
1.6V
50mV
100mV
200mV
400mV
800mV
1.6V
VOUT = 3.3 V = 0.5 V + 400 mV + 800 mV + 1.6 V
0.5 V is Vref
VOUT = 0.5 V ´ (1 + 3.2R/0.571R)
VOUT = 3.5 V = 0.5 V + 200 mV + 400 mV + 800 mV + 1.6 V
0.5 V is Vref
0.571R is parallel resistance of 4R, 2R, and 1R.
Figure 38. 3.3-V Configuration
14
FB
32R
Submit Documentation Feedback
VOUT = 0.5 V ´ (1 + 3.2R/0.533R)
0.533R is parallel resistance of 8R, 4R, 2R, and 1R.
Figure 39. 3.5-V Configuration
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
See Table 1 for a full list of target output voltages and corresponding pin settings. The voltage setting pins have
a binary weight; therefore, the output voltage can be programmed to any value from 0.9 V to 3.5 V in 50-mV
steps.
Figure 12 and Figure 13 shows this output voltage programming performance.
NOTE
Any output voltage setting that is not listed in Table 1 is not covered in the Electrical
Characteristics. For output voltages greater than 3.5 V, use a traditional adjustable
configuration (see the TRADITIONAL ADJUSTABLE CONFIGURATION section).
Table 1. User Configurable Output Voltage Setting
VOUT(TARGET)
(V)
50mV
1.6V
VOUT(TARGET)
(V)
0.90
open
open
open
GND
0.95
GND
open
open
GND
open
open
open
open
1.00
open
GND
open
1.05
GND
GND
open
GND
open
GND
open
1.10
open
open
GND
GND
1.15
GND
open
GND
1.20
1.25
open
GND
GND
GND
1.30
open
1.35
1.40
1.45
100mV 200mV 400mV 800mV
50mV 100mV 200mV 400mV 800mV
1.6V
2.25
GND
GND
open
open
open
GND
2.30
open
open
GND
open
open
GND
open
2.35
GND
open
GND
open
open
GND
open
2.40
open
GND
GND
open
open
GND
open
open
2.45
GND
GND
GND
open
open
GND
GND
open
open
2.50
open
open
open
GND
open
GND
GND
GND
open
open
2.55
GND
open
open
GND
open
GND
GND
GND
open
open
2.60
open
GND
open
GND
open
GND
open
open
open
GND
open
2.65
GND
GND
open
GND
open
GND
GND
open
open
open
GND
open
2.70
open
open
GND
GND
open
GND
open
GND
open
open
GND
open
2.75
GND
open
GND
GND
open
GND
GND
GND
open
open
GND
open
2.80
open
GND
GND
GND
open
GND
1.50
open
open
GND
open
GND
open
2.85
GND
GND
GND
GND
open
GND
1.55
GND
open
GND
open
GND
open
2.90
open
open
open
open
GND
GND
1.60
open
GND
GND
open
GND
open
2.95
GND
open
open
open
GND
GND
1.65
GND
GND
GND
open
GND
open
3.00
open
GND
open
open
GND
GND
1.70
open
open
open
GND
GND
open
3.05
GND
GND
open
open
GND
GND
1.75
GND
open
open
GND
GND
open
3.10
open
open
GND
open
GND
GND
1.80
open
GND
open
GND
GND
open
3.15
GND
open
GND
open
GND
GND
1.85
GND
GND
open
GND
GND
open
3.20
open
GND
GND
open
GND
GND
1.90
open
open
GND
GND
GND
open
3.25
GND
GND
GND
open
GND
GND
1.95
GND
open
GND
GND
GND
open
3.30
open
open
open
GND
GND
GND
2.00
open
GND
GND
GND
GND
open
3.35
GND
open
open
GND
GND
GND
2.05
GND
GND
GND
GND
GND
open
3.40
open
GND
open
GND
GND
GND
2.10
open
open
open
open
open
GND
3.45
GND
GND
open
GND
GND
GND
2.15
GND
open
open
open
open
GND
3.50
open
open
GND
GND
GND
GND
2.20
open
GND
open
open
open
GND
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
TRADITIONAL ADJUSTABLE CONFIGURATION
For any output voltage target that is not supported in the USER-CONFIGURABLE OUTPUT VOLTAGE section,
a traditional adjustable configuration with external-feedback resistors can be used with the TPS7A7300.
Figure 40 shows how to configure the TPS7A7300 as an adjustable regulator with an equation and Table 2 lists
recommended pairs of feedback resistor values.
IN
IN
OUT
GND
OUT
NOTE
The bottom side of feedback resistor R2 in Figure 40 should be in the range of 27 kΩ to
33 kΩ in order to maintain the specified regulation accuracy.
OUT
IN
R1
SNS
EN
R2
FB
SS
PG
NC
Thermal Pad
1.6V
400mV
Optional
800mV
GND
200mV
100mV
50mV
VIN
FB
OUT
SNS
0.5 V
3.2R
FB
32R
16R
8R
4R
2R
1R
50mV
100mV
200mV
400mV
800mV
1.6V
R1
R2
VOUT =
(R1 + R2 )
x 0.500
R2
Figure 40. Traditional Adjustable Configuration with External Resistors
Table 2. Recommended Feedback-Resistor Values
16
E96 SERIES
R40 SERIES
VOUT(TARGET)
(V)
R1 (kΩ)
R2 (kΩ)
R1 (kΩ)
R2 (kΩ)
1.00
30.1
30.1
30.0
30.0
1.20
39.2
28.0
43.7
31.5
1.50
61.9
30.9
60.0
30.0
1.80
80.6
30.9
80.0
30.7
1.90
86.6
30.9
87.5
31.5
2.50
115
28.7
112
28.0
3.00
147
29.4
150
30.0
3.30
165
29.4
175
31.5
5.00
280
30.9
243
27.2
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
DROPOUT VOLTAGE
The TPS7A7300 maintains its output voltage regulation with a dropout voltage (VIN – VOUT) greater than 0.24 V
under the test conditions specified in the Electrical Characteristics. In most power distribution tree (system)
designs, the TPS7A7300 can be used with a 0.3-V difference in the common voltage rails (for example, from 3.3
VIN to 3.0 VOUT, from 1.8 VIN to 1.5 VOUT, or from 1.5 VIN to 1.2 VIN).
INPUT CAPACITOR REQUIREMENTS
As a result of its very fast transient response and low-dropout operation support, it is necessary to reduce the
line impedance at the input pin of the TPS7A7300. The line impedance depends heavily on various factors, such
as wire (PCB trace) resistance, wire inductance, and/or output impedance of the upstream voltage supply (power
supply to the TPS7A7300). Therefore, a specific value for the input capacitance cannot be recommended until
the previously listed factors are finalized.
In addition, simple usage of large input capacitance is known to form unwanted LC resonance in combination
with input wire inductance. For example, a 5-nH inductor and a 10-µF input capacitor form an LC filter that has a
resonance at 712 kHz. This value of 712 kHz is well inside the bandwidth of the TPS7A7300 control loop.
The best guideline is to use a capacitor of up to 1 µF with well-designed wire connections (PCB layout) to the
upstream supply. In case it is difficult to optimize the input line, use a large tantalum capacitor in combination
with a good-quality, low-ESR, 1-µF ceramic capacitor.
OUTPUT CAPACITOR REQUIREMENTS
The TPS7A7300 is designed to be stable with standard ceramic capacitors with capacitance values greater than
or equal to 4.7 μF. The TPS7A7300 is evaluated using an X5R-type, 10-μF ceramic capacitor. X5R- and X7Rtype capacitors are highly recommended because they have minimal variation in value and ESR over
temperature. Maximum ESR should be below 1.0 Ω.
As with any regulator, increasing the size of the output capacitor reduces overshoot and undershoot magnitude,
but increases duration of the transient response.
UNDERVOLTAGE LOCK-OUT (UVLO)
The TPS7A7300 uses an undervoltage lock-out circuit to keep the output shut off until the internal circuitry is
operating properly. The UVLO circuit has a deglitch feature that typically ignores undershoot of the input voltage
upon the event of device start-up. Still, a poor input line impedance may cause a severe input voltage drop when
the device powers on. As explained in the INPUT CAPACITOR REQUIREMENTS section, the input line
impedance should be well-designed.
SOFT-START
The TPS7A7300 has a SS pin that provides a soft-start (slow start) function.
By leaving the SS pin open, the TPS7A7300 performes a soft-start by its default setting.
As shown in Figure 1, by connecting a capacitor between the SS pin and the ground, the CSS capacitor forms an
RC pair together with the integrated 50-kΩ resistor. The RC pair operates as an RC-delay circuit for the soft-start
together with the internal 700-µs delay circuit.
The relationship between CSS and the soft-start time is shown in Figure 31 through Figure 33.
CURRENT LIMIT
The TPS7A7300 internal current limit circuitry protects the regulator during fault conditions. During a current limit
event, the output sources a fixed amount of current that is mostly independent of the output voltage. The current
limit function is provided as a fail-safe mechanism and is not intended to be used regularly. Do not design any
applications to use this current limit function as a part of expected normal operation. Extended periods of current
limit operation degrade device reliability.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
ENABLE AND SHUTDOWN THE DEVICE
The EN pin switches the enable and disable (shutdown) states of the TPS7A7300. A logic high input at the EN
pin enables the device; a logic low input disables the device. When disabled, the device consumption current is
reduced.
POWER GOOD
The TPS7A7300 has a power good function that works with the PG output pin. When the output voltage
undershoots the threshold voltage VIT(PG) during normal operation, the PG open-drain output turns from a highimpedance state to a low-impedance state. When the output voltage exceeds the VIT(PG) threshold by an amount
greater than the PG hysteresis, Vhys(PG), the PG open-drain output turns from a low-impedance state to highimpedance state. By connecting a pull-up resistor (usually between OUT and PG), any downstream device can
receive an active-high enable logic signal.
When setting the output voltage to less than 1.8 V and using a pull-up resistor between OUT and PG, depending
on the downstream device specifications, the downstream device may not accept the PG output as a valid highlevel logic voltage. In such cases, put a pull-up resistor between IN and PG, not between OUT and PG.
Figure 19 shows the open-drain output drive capability. The on-resistance of the open-drain transistor is
calculated using Figure 19, and is approximately 200 Ω. Any pull-up resistor greater than 10 kΩ works fine for
this purpose.
THERMAL INFORMATION
Thermal Protection
The thermal protection feature disables the output when the junction temperature rises to approximately +160°C,
allowing the device to cool. When the junction temperature cools to approximately +140°C, the output circuitry is
enabled. Depending on power dissipation, thermal resistance, and ambient temperature, the thermal protection
circuit may cycle on and off. This thermal limit protects the device from damage as a result of overheating.
Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate
heatsink. For reliable operation, junction temperature should be limited to +125°C maximum. To estimate the
margin of safety in a complete design (including heatsink), increase the ambient temperature until the thermal
protection is triggered; use worst-case loads and signal conditions. For good reliability, thermal protection should
trigger at least +35°C above the maximum expected ambient condition of your particular application. This
configuration produces a worst-case junction temperature of +125°C at the highest expected ambient
temperature and worst-case load.
The internal protection circuitry of the TPS7A7300 has been designed to protect against overload conditions. It
was not intended to replace proper heatsinking. Continuously running the TPS7A7300 into thermal shutdown
degrades device reliability.
Power Dissipation
Knowing the device power dissipation and proper sizing of the thermal plane that is connected to the tab or pad
is critical to avoiding thermal shutdown and ensuring reliable operation.
Power dissipation of the device depends on input voltage and load conditions and can be calculated using
Equation 1:
P D + ǒVIN * VOUTǓ
I OUT
(1)
Power dissipation can be minimized and greater efficiency can be achieved by using the lowest possible input
voltage necessary to achieve the required output voltage regulation.
18
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
On the QFN (RGW) package, the primary conduction path for heat is through the exposed pad to the PCB. The
pad can be connected to ground or be left floating; however, it should be attached to an appropriate amount of
copper PCB area to ensure the device does not overheat. The maximum junction-to-ambient thermal resistance
depends on the maximum ambient temperature, maximum device junction temperature, and power dissipation of
the device and can be calculated using Equation 2:
RqJA =
+125°C - TA
PD
(2)
Knowing the maximum RθJA, the minimum amount of PCB copper area needed for appropriate heatsinking can
be estimated using Figure 41.
120
100
qJA (°C/W)
80
60
qJA (RGW)
40
20
0
0
1
2
3
4
5
7
6
8
9
10
2
Board Copper Area (in )
2
NOTE: θJA value at a board size of 9-in (that is, 3-in × 3-in) is a JEDEC standard.
Figure 41. θJA vs Board Size
Figure 41 shows the variation of θJA as a function of ground plane copper area in the board. It is intended only as
a guideline to demonstrate the effects of heat spreading in the ground plane and should not be used to estimate
actual thermal performance in real application environments.
NOTE: When the device is mounted on an application PCB, it is strongly recommended to use ΨJT and ΨJB, as
explained in the Estimating Junction Temperature section.
Estimating Junction Temperature
Using the thermal metrics ΨJT and ΨJB, as shown in the Thermal Information table, the junction temperature can
be estimated with corresponding formulas (given in Equation 3). For backwards compatibility, an older θJC,Top
parameter is listed as well.
YJT: TJ = TT + YJT · PD
YJB: TJ = TB + YJB · PD
Where:
PD is the power dissipation shown by Equation 2.
TT is the temperature at the center-top of the IC package.
TB is the PCB temperature measured 1mm away from the IC package on the PCB surface (as
Figure 43 shows).
(3)
NOTE: Both TT and TB can be measured on actual application boards using a thermo-gun (an infrared
thermometer).
For more information about measuring TT and TB, see Application Report SBVA025, Using New Thermal Metrics,
available for download at www.ti.com.
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
19
TPS7A7300
SBVS190B – MARCH 2012 – REVISED APRIL 2012
www.ti.com
By looking at Figure 42, the new thermal metrics (ΨJT and ΨJB) have very little dependency on board size. That
is, using ΨJT or ΨJB with Equation 3 is a good way to estimate TJ by simply measuring TT or TB, regardless of the
application board size.
12
YJT and YJB (°C/W)
10
YJB (RGW)
8
6
4
2
YJT (RGW)
0
0
2
4
6
8
10
2
Board Copper Area (in )
Figure 42. ΨJT and ΨJB vs Board Size
For a more detailed discussion of why TI does not recommend using θJC(top) to determine thermal characteristics,
refer to Application Report SBVA025, Using New Thermal Metrics, available for download at www.ti.com. For
further information, refer to Application Report SPRA953, IC Package Thermal Metrics, also available on the TI
website.
TB on PCB
TT on top of IC
1mm
(a) Example RGW (QFN) Package Measurement
Figure 43. Measuring Points for TT and TB
20
Submit Documentation Feedback
Copyright © 2012, Texas Instruments Incorporated
TPS7A7300
www.ti.com
SBVS190B – MARCH 2012 – REVISED APRIL 2012
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (March 2012) to Revision B
•
Page
Changed Thermal Information table note (3b) copper coverage from 20% to 4% ............................................................... 3
Changes from Original (March 2012) to Revision A
•
Page
Changed from product preview to production data ............................................................................................................... 1
Copyright © 2012, Texas Instruments Incorporated
Submit Documentation Feedback
21
PACKAGE OPTION ADDENDUM
www.ti.com
19-Apr-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
TPS7A7300RGWR
ACTIVE
VQFN
RGW
20
3000
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
TPS7A7300RGWT
ACTIVE
VQFN
RGW
20
250
Green (RoHS
& no Sb/Br)
CU NIPDAUAGLevel-2-260C-1 YEAR
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-May-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS7A7300RGWR
VQFN
RGW
20
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
TPS7A7300RGWT
VQFN
RGW
20
250
180.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-May-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS7A7300RGWR
VQFN
RGW
20
3000
346.0
346.0
29.0
TPS7A7300RGWT
VQFN
RGW
20
250
210.0
185.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated