CDIL CSA1015Y

Continental Device India Limited
An ISO/TS16949 and ISO 9001 Certified Company
PNP EPITAXIAL PLANAR SILICON TRANSISTOR
CSA1015
TO-92
Plastic Package
E
CB
Audio Frequency General Purpose and Driver Stage Amplifier Applications.
Complementary CSC1815
ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise)
DESCRIPTION
SYMBOL
VCBO
Collector Base Voltage
VALUE
50
UNITS
V
Collector Emitter Voltage
VCEO
50
V
Emitter Base Voltage
VEBO
5
V
Collector Current Continuous
IC
150
mA
Base Current
IB
50
mA
Collector Power Dissipation
PC
625
mW
Tj, Tstg
-55 to +125
ºC
Rth(j-c)
250
ºC/W
Operating And Storage Junction
Temperature Range
THERMAL RESISTANCE
Junction to case
ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise)
DESCRIPTION
SYMBOL TEST CONDITION
ICBO
VCB =50V, IE=0
Collector Cut off Current
IEBO
VEB=5V, IC = 0
Emitter Cut off Current
DC Current Gain
Collector Emitter Saturation Voltage
Base Emitter Saturation Voltage
*hFE
IC =2mA, VCE=6V
70
hFE
IC =150mA, VCE=6V
25
VCE(sat)
VBE(sat)
TYP
ft
Collector Output Capacitance
Cob
Base Spreading Resistance
rbb'
Noise Figure
NF
VCE=10V, IC=1mA,
f=100MHz
VCB=10V,IE=0,
f=1MHz
VCB=10V, IE=1mA,
f=30MHz
VCE=6V, IC=0.1mA,
O
70 - 140
Rg=10Kohms, f=1KHz
Y
120 - 240
MAX
100
UNITS
nA
100
nA
400
IC=100mA,IB= 10mA
IC=100mA,IB= 10mA
DYNAMIC CHARACTERISTICS
Transition Frequency
CLASSIFICATION
*hFE
MIN
0.30
1.1
80
V
V
MHz
7.0
pF
Ω
30
10
dB
GR
200 - 400
CSA1015REV_5 281202D
Continental Device India Limited
Datasheet
Page 1 of 4
CSA1015
TO-92
Plastic Package
TO-92 Plastic Package
A
Uncontrolled
2
E
3
D
MIN.
4.32
MAX.
5.33
B
4.45
3.18
5.20
4.19
0.41
0.55
0.35
0.50
E
F
5 DEG
G
1.14
1.40
1.20
1.40
H
12.70
K
—
1.982 2.082
L
M
1.03
1.20
All dimensions are in mm
D
K
Beyond 'L'
Solderability Ensured
1
DIM
A
C
D
L
Dimension With 'L'
B
SEC AA
A A
G
F
C
3 2 1
H
M
F
Mold
Parting
Line
PIN CONFIGURATION
1. BASE
2. COLLECTOR
3. EMITTER
3 2 1
The TO-92 Package, Tape and Ammo Pack Drawings are correct as on the date of issue/revision of this Data Sheet.
The currently valid dimensions and information, may please be confirmed from the TO-92 Drawing in the Packages and
Packing Section of the Product Catalogue.
Packing Details
PACKAGE
STANDARD PACK
INNER CARTON BOX
OUTER CARTON BOX
Details
Net Weight/Qty
Size
Qty
Size
Qty
Gr Wt
TO-92 Bulk
1K/polybag
200 gm/1K pcs
3" x 7.5" x 7.5"
5K
17" x 15" x 13.5"
80K
23 kgs
TO-92 T&A
2K/ammo box
645 gm/2K pcs
12.5" x 8" x 1.8"
2K
17" x 15" x 13.5"
32K
12.5 kgs
CSA1015REV_5 281202D
Continental Device India Limited
Datasheet
Page 2 of 4
CSA1015
TO-92
Plastic Package
TO-92 Tape and Ammo Pack
Tape Mechanical Data
h
(p)
P
T
h
h1
Ammo Pack Style
Adhesive Tape on Top Side
h1
A1
D
FEE
Flat side
A
H3
H2
Label
C1
H1
Ho
186
(7.3")
W2
C2
Wo
L
Carrier
Strip
W1
W
F1
F2
Do
(1
332
F
t1
(1. 43
7")
P2
t
Po
3")
Flat Side of Transistor and
Adhesive Tape Visible
2000 pcs./Ammo Pack
All dimensions are in mm
ITEM
BODY WIDTH
BODY HEIGHT
BODY THICKNESS
PITCH OF COMPONENT
* 1 FEED HOLE PITCH
* 2 FEED HOLE CENTRE TO
COMPONENT CENTRE
DISTANCE BETWEEN OUTER
LEADS
* 3 COMPONENT ALIGNMENT SIDE VIEW
* 4 COMPONENT ALIGNMENT FRONT VIEW
TAPE WIDTH
HOLD-DOWN TAPE WIDTH
HOLE POSITION
HOLD-DOWN TAPE POSITION
LEAD WIRE CLINCH HEIGHT
COMPONENT HEIGHT
LENGTH OF SNIPPED LEADS
FEED HOLE DIAMETER
* 5 TOTAL TAPE THICKNESS
LEAD - TO - LEAD DISTANCE
STAND OFF
CLINCH HEIGHT
LEAD PARALLELISM
PULL - OUT FORCE
SPECIFICATION
SYMBOL
A1
A
T
P
Po
MIN. NOM. MAX.
4.0
4.8
3.9
TOL .
NOTES
4.8
5.2
4.2
1. Maximum alignment deviation between
leads will not to be greater than 0.2mm.
12.7
12.7
± 1.0
± 0.3
2. Maximum non-cumulative variation
between tape feed holes shall not
exceed 1 mm in 20 pitches.
P2
6.35
± 0.4
F
5.08
+ 0.6
- 0.2
3. Holddown tape will not exceed beyond
the edge(s) of carrier tape and there
shall be no exposure of adhesive.
h
h1
W
Wo
W1
0
0
18
6
9
W2
Ho
H1
L
Do
t
F1, F2
0.5
16
H2
H3
| C1 - C2 |
(p)
1.0
1.3
± 0.5
± 0.2
+ 0.7
- 0.5
± 0.2
± 0.5
4. There will be no more than three (3)
consecutive missing components in a
tape.
5. A tape trailer, having at least three feed
holes are provided after the last
component in a tape.
6. Splices should not interfere with the
sprocket feed holes.
23.25
11.0
4
± 0.2
1.2
2.54
0.45
6N
1.45
3.0
0.22
+ 0.4
- 0.1
REMARKS
* 1 Cumulative pitch error 1.0 mm/20 pitch
* 2 To be measured at bottom of clinch
* 3 At top of body
* 4 At top of body
* 5 t1 0.3 – 0.6 mm
CSA1015REV_5 281202D
Continental Device India Limited
Datasheet
Page 3 of 4
Notes
CSA1015
TO-92
Plastic Package
Disclaimer
The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited
for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as
to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and
on the CDIL Web Site/CD are believed to be accurate and reliable. CDIL however, does not assume responsibility for
inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or
use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not
designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual
Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or
applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s).
CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice.
CDIL is a registered Trademark of
Continental Device India Limited
C-120 Naraina Industrial Area, New Delhi 110 028, India.
Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119
email@cdil.com
www.cdilsemi.com
CSA1015REV_5 281202D
Continental Device India Limited
Datasheet
Page 4 of 4