CANDD NMJ

NMJ SERIES
5.2kVDC Isolated 1W DC/DC Converters
SELECTION GUIDE
Nominal
Input
Voltage
Output
Voltage
Output
Current
Efficiency
Isolation
Capacitance
MTTF1
Order Code
(V)
(V)
(mA)
(%)
(pF)
kHrs
NMJ0505S
5
5
±100
65
1.6
1517
NMJ0509S
5
9
±55
70
1.6
619
NMJ0512S
5
12
±42
70
1.8
313
NMJ0515S
5
15
±33
70
1.9
172
NMJ1205S
12
5
±100
65
1.8
456
NMJ1209S
12
9
±55
70
1.9
318
NMJ1212S
12
12
±42
70
2.0
211
NMJ1215S
12
15
±33
70
2.1
136
FEATURES
■ Wide Temperature Performance at
Full 1W Load, –40°C to 85°C
■ BS EN 60950 Certified
■ 5.2kVDC Isolation (1 Minute)
■ Dual Outputs
■ Power Sharing
■ SIP Package Style
■ Efficiency to 80%
■ Power Density 0.42W/cm3
■ 5V & 12V Input
■ 5V, 9V, 12V & 15V Output
■ Pin Compatible with NMV Series SIP
DC/DC Converters
■ Footprint 1.91cm2
■ UL 94V-0 Package Material
■ No Heatsink required
■ Internal SMD Construction
When operated with additional external load capacitance the rise time of the input voltage will determine the
maximum external capacitance value for guaranteed start up. The slower the rise time of the input voltage the
greater the maximum value of the additional external capacitance for reliable start up.
INPUT CHARACTERISTICS
Parameter
Conditions
MIN
TYP
MAX
Units
Voltage Range
Continuous operation, 5V input types
Continuous operation, 12V input types
4.5
10.8
5
12
5.5
13.2
V
MIN
TYP
MAX
Units
1
W
10
%
1.2
15
10
10
10
200
%/%
■ Toroidal Magnetics
■ Fully Encapsulated
OUTPUT CHARACTERISTICS
■ MTTF up to 1.6 Million Hours
Parameter
Conditions
■ Custom Solutions Available
Rated Power2
Output Voltage
Accuracy
Line Regulation
TA= –40°C to 85°C
DESCRIPTION
The NMJ series are dual output DC/DC
converters in a 7 pin SIP package style
offering pin and functionality compatibility
with the NMV series SIP DC/DC converters.
The series was tested by British Standards
Institute (BSI) and received certificate number
8105 issue 2 confirming compliance with BS
EN 60950 and IEC 950 safety standards for
reinforced insulation. The NMJ series is
suitable for applications where safety and
miniaturisation are of paramount importance.
EN 60950 is derived from IEC 950 and is
equivalent to UL 1950 and CSA 950
standards.
www.cdpoweronline.com
See tolerance envelope
High VIN to low VIN
10% load to rated load, 5V output types
10% load to rated load, 9V output types
Load Regulation
10% load to rated load, 12V output types
10% load to rated load, 15V output types
Ripple & Noise BW=DC to 20MHz, all output types
Zero Load Power 5V output types
Consumption
12V output types
–7.5
1.0
10
6
6
6
275
185
%
mV p-p
mW
ABSOLUTE MAXIMUM RATINGS
Short-circuit duration3
Lead temperature 1.5mm from case for 10 seconds
Input voltage VIN, NMJ05 types
Input voltage VIN, NMJ12 types
1 second
300°C
7V
15V
1 Calculated using MIL-HDBK-217F with nominal input voltage at full load.
2 See derating curve
3 Supply voltage must be discontinued at the end of the short circuit duration.
All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.
NMJ SERIES
5.2kVDC Isolated 1W DC/DC Converters
ISOLATION CHARACTERISTICS
Parameter
Conditions
Isolation Test Voltage
Resistance
1 minute
500VDC
MIN
TYP
MAX
Units
5200
VDC
MΩ
1000
GENERAL CHARACTERISTICS
Parameter
Conditions
MIN
Switching Frequency
TYP
MAX
Units
70
kHz
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
MIN
Specification
Storage
Case Temperature
Above Ambient
Cooling
All output types
-40
-55
TYP
MAX
Units
85
130
°C
°C
30
°C
All output types
Free air convection
PERFORMANCE CHARACTERISTICS
tolerance envelope
2.0
+10%
+6%
+2.5%
V nominal
temperature derating graph
1.5
Output Power (W)
–4%
Output Voltage
–7.5%
10
50
Output Load Current (%)
100
85°C
1.0
0.5
Safe Operating Area
0
-40
0
50
100
Ambient Temperature (°C)
150
MECHANICAL DIMENSIONS
7 Pin SIP
0.77 (19.50)
0.39
(9.80)
0.49
(12.50)
NMJ0505S
0.094
(2.40)
XYYWWi
0.022 (0.55)
0.018 (0.45)
PIN
1
VIN
2 GND
5
–V
6
0V
7
+V
0.18 (4.60)
0.14 (3.60)
1 2
0.074±0.02
1.88±0.50
5 6 7
0.10 (2.54)
0.012 (0.30)
0.007 (0.20)
0.022 (0.55)
0.018 (0.45)
Weight: 4.9g
All dimensions in mm XX.XX ±0.25mm. All pins on a 2.54mm pitch and within ±0.25mm of true position.
C&D Technologies (NCL) Limited reserve the right to alter or improve the
specification, internal design or manufacturing process at any time, without
notice. Please check with your supplier or visit our web site to ensure that
you have the current and complete specification for your product before use.
© C&D Technologies (NCL) Limited 2003
NDC NM J.4
No part of this publication may be copied, transmitted or stored in a
retrieval system or reproduced in any way including, but not limited to,
photography, photocopy, magnetic or other recording means, without prior
written permission from C&D Technologies (NCL) Limited.
Instructions for use are available from www.cdpoweronline.com
C&D Technologies (NCL) Ltd
Tanners Drive, Blakelands North
Milton Keynes MK14 5BU, England
Tel: +44 (0)1908 615232
Fax: +44 (0)1908 617545
email: info@cdtechno-ncl.com
www.cdpoweronline.com
C&D Technologies Inc.
3400 E Britannia Drive, Tucson,
Arizona 85706, USA
Tel: +1 (800) 547-2537
Fax: +1 (520) 741-4598
email: sales@cdtechno.com