EVERLIGHT 19-217-Y5C-AQ2R2

Technical Data Sheet
0603 Package Chip LED (0.4mm Height)
19-217/Y5C-AQ2R2/3T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Descriptions
․The 19-217 SMD LED is much smaller than lead
frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Part No.
Emitted Color
Resin Color
Brilliant Yellow
Water Clear
Material
19-217/Y5C-AQ2R2/3T
Everlight Electronics Co., Ltd.
Device No:
AlGaInP
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 1 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 2 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
IFP
60
mA
Power Dissipation
Pd
60
mW
Electrostatic Discharge(HBM)
ESD
2000
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +90
℃
Soldering Temperature
Tsol
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
90.0
-----
180
mcd
Viewing Angle
2θ1/2
----
120
----
deg
Peak Wavelength
λp
----
591
----
nm
Dominant Wavelength
λd
585.5
----
594.5
nm
Spectrum Radiation
Bandwidth
△λ
----
15
----
nm
Forward Voltage
VF
1.7
2.0
2.4
V
Reverse Current
IR
----
----
10
μA
Condition
IF=20mA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 3 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Bin Range Of Luminous Intensity
Bin
Min
Max
Q2
90.0
112
R1
112
140
R1
140
180
Unit
Condition
mcd
IF=20mA
Unit
Condition
nm
IF=20mA
Bin Rang Of Dom. Wavelength
Groups
A
Bin
Min
Max
D3
585.5
588.5
D4
588.5
591.5
D5
591.5
594.5
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 4 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 5 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 6 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm,Unit = mm
Moisture Resistant Packaging
Label
Aluminum moistue-proof bag
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Desiccant
Rev 1
Label
Page: 7 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level : 90 %
LTPD : 10 %
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 240℃±5℃
5 sec.
Test
Sample
Ac/Re
Hours/Cycles Size
22 Pcs.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS.
0/1
3
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS.
0/1
4
High Temperature
Storage
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
5
Low Temperature
Storage
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/RH85%
1000 Hrs.
22 PCS.
0/1
2
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
6 Min.
Rev 1
Page: 8 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Lead solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 9 of 10
Prepared by:Chen Zheng
19-217/Y5C-AQ2R2/3T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Everlight Electronics Co., Ltd.
Device No:
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
http://www.everlight.com
Prepared date: 1-Jul.-2011
Rev 1
Page: 10 of 10
Prepared by:Chen Zheng