EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Chip LEDs with Right Angle Lens 22-21/BHC-AN1P2/2C Features ․Package in 8mm tape on 7〞diameter reel. ․Compatible with automatic placement equipment. ․Compatible with infrared and vapor phase reflow solder process. ․Mono-color type. ․Pb free. Descriptions ․ The 22-21 SMD series taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. ․Besides, lightweight makes them ideal for miniature applications. etc. Applications ․Automotive: backlighting in dashboard and switch. ․Telecommunication: indicator and backlighting in telephone and fax. ․Flat backlight for LCD, switch and symbol. ․General use. Device Selection Guide Chip Material Emitted Color InGaN Brilliant Blue Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 1 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Package Outline Dimensions Notes: Tolerances Unless Dimension ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 2 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40~ +90 ℃ Soldering Temperature Tsol Electrostatic Discharge ESD 150 V Power Dissipation Pd 110 mW IFP 100 mA Peak Forward Current (Duty 1/10 @1KHz) 260 (for 5 ℃ second) Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Min. Typ. Max. Unit Condition Luminous Ientensity Iv 28.5 ----- 72 mcd IF=20mA Viewing Angle 2θ1/2 ---- 130 ----- deg IF=20mA Peak Wavelength λp ----- 468 ----- nm IF=20mA Dominant Wavelength λd 464.5 ----- 476.5 nm IF=20mA Bandwidth △λ ----- 35 ----- nm IF=20mA Forward Voltage VF ----- 3.8 4.5 V IF=20mA Reverse Current IR ----- ----- 50 μA VR=5V Spectrum Radiation Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 3 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Bin Rang Of Dom. Wavelength Groups A Bin Min Max A9 464.5 467.5 A10 467.5 470.5 A11 470.5 473.5 A12 473.5 476.5 Unit Condition nm IF=20mA Unit Condition mcd IF=20mA Bin Rang Of Luminous Intensity Bin Min Max N1 28.5 36 N2 36 45 P1 45 57 P2 57 72 Notes: 1.Tolerance of Luminous Intensity ±10% 2.Tolerance of Dominant Wavelength ±1nm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 4 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 5 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 6 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned is ±0.1mm, Unit = mm Moisture Resistant Packaging Label Aluminum moistue-proof bag Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Desiccant Rev. 1.0 Label Page: 7 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level：90% LTPD：10% No. Items Test Condition 1 Reflow Soldering Temp. : 260℃±5℃ Min. 5 sec. Test Sample Ac/Re Hours/Cycles Size 22 PCs. 0/1 Temperature Cycle H : +100℃ 15min ∫ 5 min L : -40℃ 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100℃ 5min ∫ 10 sec L : -10℃ 5min 300 Cycles 22 PCS. 0/1 4 High Temperature Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1 5 Low Temperature Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85℃/85%RH. 1000 Hrs. 22 PCS. 0/1 2 Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 6 Min. Rev. 1.0 Page: 8 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 60±5℃ for 24 hours. 3. Soldering Condition 3.1 Lead solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 9 of 10 Prepared by: ForrestChen EVERLIGHT ELECTRONICS CO.,LTD. 22-21/BHC-AN1P2/2C 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No. : DSE-221-B01 Prepared date:2004.08.05 Rev. 1.0 Page: 10 of 10 Prepared by: ForrestChen