XRP7713 Three Channel Digital PWM Step Down Controller December 2010 Rev. 1.1.1 GENERAL DESCRIPTION APPLICATIONS The XRP7713 is a three output pulse-width modulated (PWM) step-down DC-DC controller with a built-in LDO for standby power and GPIOs. The device provides a complete power management solution in one IC and is fully programmable via an I2C serial interface. Independent Digital Pulse Width Modulator (DPWM) channels regulate output voltages and provide all required protection functions such as current limiting and over-voltage protection. Each output voltage can be programmed from 0.9V to 5.1V without the need of an external voltage divider. The wide range of the programmable DPWM switching frequency (from 300 KHz to 1.5 MHz) enables the user to optimize between efficiency and component size. Input voltage range is from 4.75V to 25V. An I2C bus interface is provided to program the IC as well as to communicate with the host for fault reporting and handling, power rail parameters monitoring, etc. The device offers a complete solution including independently programmable: soft-start, softstop, start-up delay and ramp of each PWM regulator. • Multi Channel Power Supplies • Audio-Video Equipments • Industrial & Telecom Equipments • Processors & DSPs Based Equipments FEATURES • 3 Channel Step Down Controller − Programmable Output Voltage 0.9V-5.1V − Programmable 1.5MHz DPWM Frequency − Integrated FET Drivers • 4.75V to 5.5V and 5.5V to 25V Input Voltage Range • Up to 5 Reconfigurable GPIO Pins • Fully Programmable via I2C Interface • Independent Digital Pulse Width Modulator (DPWM) channels • Complete Monitoring and Reporting • Complete Power Up/Down Sequencing • Full On Board Protection OTP, UVLO, OCP and OVP • Built-in 3.3V/5V LDO • PowerArchitect™ Design Software • Green/Halogen Free 32-pin TQFN TYPICAL APPLICATION DIAGRAM Fig. 1: XRP7713 Application Diagram Exar Corporation 48720 Kato Road, Fremont CA 94538, USA www.exar.com Tel. +1 510 668-7000 – Fax. +1 510 668-7001 XRP7713 Three Channel Digital PWM Step Down Controller ABSOLUTE MAXIMUM RATINGS OPERATING RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Input Voltage Range..................................... 5.5V to 25V Input Voltage VIN=VCCA ........................... 4.75V to 5.5V Junction Temperature Range ....................-40°C to 125°C Thermal Resistance θJA ...................................... 22°C/W VCCA, VCCD, LDOOUT, GLx, VOUTx............................ 6V VDD..................................................................... 2.0V VIN....................................................................... 27V LXx .............................................................. -1V to 27V LXx ............................................................. -5V to -1V1 Logic Inputs, GPIOs, SDA, SCL ................................... 6V BSTx, GHx .................................................... VLXx + 6V ESD Rating (HBM - Human Body Model) .................... 2kV Storage Temperature .............................. -65°C to 150°C Lead Temperature (Soldering, 10 sec) ................... 300°C Note 1: 200ns Transient ELECTRICAL SPECIFICATIONS Specifications with standard type are for an Operating Junction Temperature of TJ = 25°C only; limits applying over the full Operating Junction Temperature range are denoted by a “•”. Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise indicated, VIN = 4.75V to 25V. Quiescent Current Parameter Min. Typ. Max. Units Conditions 9 mA LDOOUT enabled (no load) No switching converter channels enabled I2C communication active Switching frequency = 400kHz 180 µA EN=0V, VIN≥5.2V VIN Supply Current 28 mA 3 channels running, GH and GH = 1nF load each VIN=12V, Switching frequency = 300kHz VIN Supply Current 50 mA 3 channels running, GH and GH = 1nF load each VIN=12V, Switching frequency = 1MHz VIN Supply Current in STANDBY VIN Supply Current in SHUTDOWN Step Down Controllers Parameter VOUT Regulation Accuracy VOUT regulation range Min. Typ. Max. Units Conditions -20 20 mV • -40 40 mV • 2.6V ≤ VOUT ≤ 5.1V 0.9 5.1 • Programmable range of each channel2 0.9V ≤ VOUT ≤ 2.5V VOUT set point resolution 50 VOUT set point resolution 100 0.9V ≤ VOUT ≤ 2.5V VOUT Input Current 100 nA 0.9V < VOUT <= 2.5V VOUT Input Resistance 120 kΩ 2.6V ≤ VOUT ≤ 5.1V 2.6V ≤ VOUT ≤ 5.1V Note 2: Voltages above 5.1V can be obtained by using an external voltage divider. © 2010 Exar Corporation 2/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Low Drop-out Regulator Parameter Min. Typ. Max. Units Conditions LDOOUT Output Voltage LDO=LOW 3.15 3.3 3.45 V • 4.75V≤VIN≤25V 0mA<ILDOOUT<100mA LDOOUT Output Voltage LDO=HIGH 4.75 5.0 5.25 V • 6.3≤VIN≤25V 0mA<ILDOOUT<100mA LDOOUT Short Circuit Current Limit 110 220 mA • VLDOOUT=0V Max. Units 2 LSB Auxiliary ADCs Parameter Min. Typ. Linearity Error Integral Linearity Error Differential -1 1 LSB Input Dynamic Range VIN 4.8 25 V Max. Units Conditions • Isense ADC Parameter Min. ADC LSB Typ. 5 Input Dynamic Range 0 Conditions mV -320 mV Max. Units 1500 kHz Referred to the input PWM Generators and Oscillator Parameter Min. Output frequency range 300 Output Frequency Accuracy -10 Typ. 10 % Conditions Steps defined in the table in the PWM Switching Frequency Setting section below • Channel-to-channel phase shift 90 deg Minimum On Time 40 ns 1nF of gate capacitance ns Switching frequency = 300kHz 10% to 90% duty cycle, Frequency dependant; refer to the graph in performance characteristic section ns Switching frequency = 1.5MHz 10% to 90% duty cycle, Frequency dependant; refer to the graph in performance characteristic section 13 Dead Time Adjustment Step 1.5 CLOCK IN Synchronization Range Maximum Duty Cycle2 -5 5 % • 86 % • Switching frequency = 300kHz 78 % • Switching frequency = 1.5MHz Note 2: The maximum duty cycle represents the maximum duty cycle commanded by the DPWM, is guaranteed by design, and internally set to ensure proper sampling of the current during the off-time. © 2010 Exar Corporation 3/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Digital Input/Output Pins (GPIO1-GPIO5) and ENABLE 3.3V CMOS logic compatible, 5V tolerant. Parameter Enable Pin Threshold Min. Typ. 1.08 1.14 Input Pin Low Level Input Pin High Level Input pin Capacitance V V V • 10 µA • Chip Enable rising threshold VIO=3.3V V • ISINK=1mA V • ISOURCE=1mA • ISOURCE=0mA • pF 0.4 2.4 Output Pin High Level (no load) Conditions 1.2 5 Output Pin Low Level Units 0.8 2.0 Input Pin Leakage Current Output Pin High Level Max. 3.3 3.6 V Typ. Max. Units I2C Specification Parameter Min. I2C Speed 400 kHz Input Pin Low Level, VIL 1.0 V Input Pin High Level, VIH Hysteresis of Schmitt Trigger Inputs, VHYS 2.31 V 0.165 V Output Pin Low Level (open drain or collector) VOL Input Leakage Current Output Fall Time from VIHMIN to VILMAX -10 20+0.1Cb3 Capacitance for each I/O Pin Conditions Based upon I2C master clock ISINK=3mA 0.4 V 10 µA Input is between 0.33V and 2.31V 250 ns With a bus capacitance from 10pF to 400pF 10 pF Max. Units Note 3: Cb is the capacitance of one bus in pF Gate Drivers Parameter GH, GL Rise and Fall Time Min. Typ. 30 ns GH, GL Pull-up On-State Output Resistance 6 Ω GH, GL Pull-down On-State Output Resistance 3 Ω GH, GL Pull-down Off-State Output Resistance 50 kΩ © 2010 Exar Corporation 4/29 Conditions At 10% to 90% of full scale pulse. 1nF Cload VIN=VCCD=0V Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller BLOCK DIAGRAM BST1 Channel 1 VOUT1 Feedback ADC1/2 GH1 Digital PID PreScaler Delay Vtar DAC – PGND1 6 Dead Time Vtar DAC GH2 LX2 Hybrid DPWM Digital PID PreScaler Gate Driver GL2 PGND2 Isense2 SS & PD VOUT3 GL1 BST2 Channel 2 Feedback ADC1/2 Gate Driver Isense1 SS & PD VOUT2 LX1 Hybrid DPWM VCCD Channel 3 Isense1 VCC VDD GPIO 0-3 SDA,SCL LDO VREF Fault Handling Isense2 PWR Good Isense3 Vout1 GPIO I2C OSC Current ADC1/2 CLOCK UVLO OTP 11-CH MUX Vout2 Vout3 Vtj VIN Configuration Registers STBY LR LDOOUT Fig. 2: XRP7713 Block Diagram © 2010 Exar Corporation 5/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller PIN ASSIGNMENT AVDD LDOOUT VIN VCCA PGND1 GL1 LX1 GH1 32 31 30 29 28 27 26 25 DVDD 1 24 BST1 GPIO1 2 23 PGND2 GPIO2 3 22 GL2 GPIO3 4 21 LX2 GPIO4 5 20 GH2 GPIO5 6 19 BST2 ENABLE 7 18 VCCD DGND 8 17 BST3 XRP7713 TQFN 5mm x 5mm Exposed Pad: AGND 15 16 LX3 GH3 PGND3 GL3 13 VOUT3 14 12 VOUT1 VOUT2 10 AGND 11 9 Fig. 3: XRP7713 Pin Assignment PIN DESCRIPTION Name Pin Number Description VIN 30 Power source for the internal linear regulators to generate VCCA, VDD and the Standby LDO (LDOOUT). Place a decoupling capacitor close to the controller IC. Also used in UVLO1 fault generation – if VIN falls below the user programmed limit, all channels are shut down. The VCCA 29 Output of the internal 5V LDO. This voltage is internally used to power analog blocks. This pin should be bypassed with a minimum of 4.7uF to AGND VCCD 18 Gate Drive input voltage. This is not an output voltage. This pin can be connected to VCCA to provide power for the Gate Drive. VCCD should be connected to VCCA with the shortest possible trace and decouple with a minimum 1µF capacitor. Alternatively, VCCD could be connected to an external supply (not greater than 5V). PGND13 28, 23,13 Power Ground. Ground connection for the low side gate driver. Connect at low side FET source. AVDD 32 DVDD 1 DGND 8 Digital Ground. Connect this pin to the ground plane at the exposed pad with a separate trace. AGND 9 Analog Ground. Connect this pin to the ground plane at the exposed pad with a separate trace Output of the internal 1.8V LDO. This pin should be bypassed with a minimum of 2.2uF to DGND Input for powering the internal digital logic. This pin should be connected to AVDD. © 2010 Exar Corporation 6/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Name Pin Number Description GL1-GL3 27, 22, 14 Output pin of the low side gate driver. Connect directly to the respective gate of an external Nchannel MOSFET. GH1-GH3 25, 20, 16 Output pin of the high side gate driver. Connect directly to the respective gate of an external Nchannel MOSFET. LX1-LX3 26, 21, 15 Lower supply rail for the high-side gate driver (GHx). Connect this pin to the switching node at the junction between the two external power MOSFETs and the inductor. These pins are also used to measure voltage drop across bottom MOSFETs in order to provide output current information to the control engine. BST1-BST3 24, 19, 17 High side driver supply pin(s). Connect BST to an external boost diode and a capacitor as shown in the front page diagram. The high side driver is connected between the BST pin and LX pin. GPIO1GPIO3 2,3,4 These pins can be configured as inputs or outputs to implement custom flags, power good signals and enable/disable controls. A GPIO pin can also be programmed as an input clock synchronizing IC to external clock. Refer to the “GPIO Pins” Section and the “External Clock Synchronization” Section for more information. GPIO4_SDA, GPIO5_SCL 5,6 I2C serial interface communication pins. These pins can be re-programmed to perform GPIO functions in applications when I2C bus is not used. VOUT14 10, 11, 12 LDOOUT 31 ENABLE 7 AGND Voltage sense. Connect to the output of the corresponding power stage. Output of the Standby LDO. It can be configured as a 5V or 3.3V output. This pin should be bypassed with a minimum of 2.2uF. If ENABLE is pulled high, the chip powers up (logic reset, registers configuration loaded, etc.). If pulled low for longer than 100us, the XRP7713 is placed into shutdown. Exposed Pad Analog Ground. Connect to analog ground (as noted above for pin 11). ORDERING INFORMATION Part Number Junction Temp Range XRP7713ILB-F -40°C≤TJ≤+125°C XRP7713ILBTR-F -40°C≤TJ≤+125°C XRP7713EVB Marking XRP7713ILB YYWW X XRP7713ILB YYWW X Package Packing Quantity Note 1 Default I2C Address 32-pin TQFN Bulk Halogen Free 0x00 32-pin TQFN 3K/Tape & Reel Halogen Free 0x00 XRP7713 Evaluation Board “YY” = Year – “WW” = Work Week – “X” = Lot Number © 2010 Exar Corporation 7/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller TYPICAL PERFORMANCE CHARACTERISTICS All data taken at TJ = TA = 25°C, unless otherwise specified - Schematic and BOM from Application Information section of this datasheet. Fig. 4: 12Vin Efficiency: Single Channel 300kHz - Channels not in use are disabled FET: Si4944; Inductor: 744314xxx 7x7x5mm Fig. 4: 12Vin Efficiency: Single Channel 300kHz - Channels not in use are disabled FET: FDS8984; Inductor: 744310200 7x7x3mm 100% 2.5V 1.8V 90% 1.2V Efficiancy 1.0V 80% 70% 60% 50% 0 1 2 3 4 5 Output Current (Amps) Fig. 5: 5Vin Efficiency: Single Channel 300kHz - Channels not in use are disabled FET: Si4944; Inductor: 744314xxx 7x7x5mm Fig. 6: 5Vin Efficiency: Single Channel 300kHz - Channels not in use are disabled FET: FDS8984; Inductor: 744314xxx 7x7x3mm Fig. 8: 12Vin Efficiency: Single Channel 1MHz - Channels not in use are disabled FET: FDS8984; Inductor:744310200 7x7x3mm Fig. 7: Combined Efficiency: 3V3 1V8 & 1V0 300 kHz FET: FDS8984; Inductor: 744314xxx 7x7x3mm © 2010 Exar Corporation 8/29 Rev. 1.1.1 XRP7713 200 2000 190 1800 180 1600 170 1400 160 1200 ISD (µA) ISD (µA) Three Channel Digital PWM Step Down Controller 150 140 1000 800 130 600 120 400 110 200 0 100 5 10 15 20 25 4.7 VIN (V) 4.8 4.8 4.9 4.9 5.0 5.0 5.1 Fig. 9: Shutdown Current 5.1V to 25V Fig. 10: Shutdown Current 4.8V to 5.1V Fig. 11: CH1:1.0V CH2:5V CH3:1.8V Simultaneous Start-up Configuration Fig. 12: CH1:1.0V CH2:5V CH3:1.8V Simultaneous Soft-Stop Fig. 13: CH1:1.0V CH2:5V CH3:1.8V Sequential Start-up Configuration Fig. 14: CH1:1.0V CH2:5V CH3:1.8V Sequential Soft-Stop Configuration Vout Shutdown = 0.8V, 1A load © 2010 Exar Corporation 5.1 5.2 VIN (V) 9/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Fig. 15: CH1:1.0V CH2:5V CH3:1.8V Sequential Soft-Stop Configuration Vout Shutdown = 0.8V, No load Fig. 16: Load Transient Response CH1: Iout (1A/div) CH2:Vout(3.3V) Fig. 17: Temperature Regulation 1.0VOUT (±1% Vout window) Fig. 18: Temperature Regulation 1.8VOUT (±1% Vo window) Fig. 19: Temperature and Voltage Regulation 1.0VOUT (±1% Vout window) Fig 21: Line/Load Regulation 1.8 VOUT (± 1% VOUT window) © 2010 Exar Corporation 10/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller FEATURES AND BENEFITS − Possible to configure as traditional ‘enable’ pin for all 3 outputs − 2 GPIOs can be dedicated to the I2C Interface as required by the customers design General DPWM Benefits: • Eliminate temperature and time variations associated with passive components in: • Frequency and Synchronization Capability − Selectable switching frequency between 300kHz and 1.5MHz − Output set point − Feedback compensation − Channel to channel phase relationship is a fixed 90 degrees − Frequency set point − Under voltage lock out − Main oscillator clock and DPWM clock can be synchronized to external sources − Input voltage measurement − ‘Master’, ‘Slave’ and ‘Stand-alone’ Configurations are possible − Gate drive dead time • Tighter parameter frequency set point tolerances including operating • Internal MOSFET Drivers − Internal FET drivers (3Ω/6Ω) for each Channel • Easy configuration and re-configuration for different Vout, Iout, Cout, and Inductor selection by simply changing internal PID coefficients. No need to change external passives for a new output specification. − Built-In Automatic Dead-time adjustment − 30ns Rise and Fall times • PowerArchitect™ Design and Configuration Software: • Higher integration: Many external circuits can be handled by monitoring or modifying internal registers • Selectable DPWM Frequency frequency and Controller − In its simplest form only VIN, VOUT, and Iout for each channel is required. Clock − The software calculates configuration register content based upon customer requirements. PID coefficients for correct loop response (for automatic or customized designs) can be generated and sent to the device. Other Benefits: • A single voltage is needed for regulation [no External LDO required]. − Configurations can be saved and/or recalled − GPIOs can be configured easily and intuitively • I2C interface allows: − Synchronization configuration can be adjusted − Communication with a System Controller or other Power Management devices for optimized system function − Interface can be used for real-time debugging and optimization • Customizing XRP7713 with customer parameters − Access to modify or read internal registers that control or monitor: − Once a configuration is finalized it can be sent to EXAR and can reside in pre-programmed parts that customers can order with an individual part number. − Output Current − Input and Output Voltage − Allows parts to be used without I2C interface − Soft-Start/Soft-Stop Time − ‘Power Good’ System Benefits: − Part Temperature • Reliability is enhanced via communication with the system controller which can obtain real time data on an output voltage, input voltage and current. − Enable/Disable Outputs − Over Current − Over Voltage • System processors can communicate with the XRP7713 directly to obtain data or make adjustments to react to circuit conditions − Temperature Faults − Adjusting fault limits and disabling/enabling faults • A system process or could also be configured to log and analyze operating history, perform diagnostics and if required, take the supply off-line after making other system adjustments. − Packet Error Checking (PEC) on I2C communication • 5 Configurable GPIO pins, (3 if I2C is in use). Pins can be configured in several ways: • If customer field service is a possibility for your end product, parameter reporting and history would provide additional capabilities for troubleshooting or aid in future system upgrades. − Fault reporting (including OCP, OVP, Temperature, Soft-Start in progress, Power Good) − Allows a Logic Level interface with other non-digital IC’s or as logic inputs to other devices © 2010 Exar Corporation 11/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller FUNCTIONAL DESCRIPTION AND OPERATION The XRP7713 is a three output digital pulse width modulation (DPWM) controller with integrated gate drivers for the use in synchronous buck switching regulators. Each output voltage can be programmed from 0.9V to 5.1V without the need of an external voltage divider. The wide range of the programmable DPWM switching frequency (from 300kHz to 1.5MHz) enables the user to optimize for efficiency or component sizes. The digital regulation loop requires no external passive components for network compensation. The loop performance does not need to be compromised due to component tolerance, aging, and operating condition. Each digital controller provides a number of safety features, such as over-current protection (OCP) and over-voltage protection (OVP). The chip also provides over-temperature protection (OTP) and under-voltage lock-out (UVLO) for two input voltage rails. The XRP7713 also has up to 5 GPIOs and a Standby Linear Regulator to provide standby power. An I2C bus interface is provided to program the IC as well as to communicate with the host for fault reporting and handling, power rail monitoring, channel enable and disable, Standby LDO voltage reconfiguration, and Standby LDO enable and disable. The XRP7713 offers a complete solution for soft-start and soft-stop. The delay and ramp of each PWM regulator can be independently controlled. During soft-stop, the output voltage ramps down with a programmable slope until it reaches a pre-set value. This pre-set value can be programmed between within zero volts and the target voltage with the same set target voltage resolution. REGISTER TYPES There are two types of registers in the XRP7713: read/write registers and read-only registers. The read/write registers are used for the control functions of the IC and can be programmed using configuration non-volatile memory (NVM) or through an I2C command. The read-only registers are for feedback functions such as error/warning flags and for reading the output voltage or current. NON-VOLATILE CONFIGURATION MEMORY The non-volatile memory (NVM) in XRP7713 stores the configuration data for the chip and all of the power rails. This memory is normally configured during manufacturing time. Once a specific bit of the NVM is programmed, that bit can never be reprogrammed again [i.e. one-time programmable]. During chip power up, the contents in the NVM are automatically transferred to the internal registers of the chip. Programmed cells have been verified to be permanent for at least 10 years and are highly reliable. POWER UP AND SEQUENCING REQUIREMENTS The XRP7713 can be programmed to sequence its outputs for nearly any imaginable loading requirement. However, there are some important sequencing requirements for the XRP7713 itself. When power is applied to the XRP7713, the 5V VCCA and 1.8V AVDD regulators must come up and stabilize to provide power for the analog and digital blocks of the IC. The Enable Pin must remain below its logic level high threshold until the AVDD is regulating to ensure proper loading of the configuration registers. For systems that control the Enable signal through a microcontroller or other processor, this is simply a matter of providing the proper delay to the Enable signal after power up. However, most users will want the part to automatically power up when power is applied to the system. To that end there are a number of recommended solutions. The most ideal sequencing method is to provide an RC time constant delay from DVDD to the Enable pin. A 10kohm resistor and a 0.1uF are all that is required. If the system needs to externally control the Enable pin as well, it is recommended that the Enable pin be pulled to ground using an open drain I/O. Using 3.3V active logic would back feed DVDD and exceed the maximum rated voltage of the pin. © 2010 Exar Corporation 12/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller For those using active 3.3V or 5V logic on the Enable pin an RC delay from VCCA to the Enable pin may be used. When using an RC delay from VCCA, attention must be paid to the amount of bypass capacitance loading AVDD since it will delay the time it takes for AVDD to power up and regulate. The AVDD and DVDD pins do not require more than 2.2uF for proper bypassing. See Figure 21 for the recommended components for sequencing the Enable pin through an RC delay from VCCA. If more capacitance is added to AVDD and DVDD, the time constant must be increased. Once Enable is asserted, an internal CHIP_READY flag goes high and enables the I2C to acknowledge the Host’s serial commands. Channels that are configured as always-on channels are enabled. Channels that are configured to be enabled by GPIOs are also enabled if the respective GPIO is asserted. VCCA 10K Enable Pin .1uF Fig. 202: RC Delay for Enable taken from VCCA In almost all cases, a simple check will ensure proper sequencing has been achieved. VCCA regulates at approximately 4.6V when the Enable pin is logic level low and at 5.1V when Enable is asserted. VCCA will typically power up and regulate before AVDD and because the internal logic is not yet powered up there is no internal shutdown signal, it will regulate at 5.1V. Once AVDD has reached sufficient voltage (and Enable is low) it will assert the internal shutdown signal and VCCA will reduce its regulated voltage to 4.6V. When the Enable is asserted, the chip will power up and VCCA will regulate at 5.1V. If our device is sequenced properly, VCCA will achieve 5.1V then drop down to 4.6V and toggle back to 5.1V. See Figure 22 for an example. Fig. 213: VCCA (green) Startup Waveform © 2010 Exar Corporation 13/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Another power-up timing concern can be observed with slowly increasing input voltages. If the UVLO Fault threshold is set to a value higher than the value of VIN when AVDD has stabilized and the enable is asserted; the UVLO Fault could assert prior to VIN reaching its final value. Increasing the value of the resistor in the RC delay will slow down the enable signal and prevent a premature UVLO Fault. STANDBY LOW DROP-OUT REGULATOR This 100mA low drop-out regulator can be programmed as 3.3V or 5V in SET_STBLDO_EN_CONFIG register. Its output is seen on the LDOOUT Pin. This LDO is fully controllable via the Enable Pin (configured to turn on as soon as power is applied), a GPIO, and/or I2C communication. The 5V output setting of the regulator is only available if VIN is above 6.3V, and the 3.3V output setting is available for the entire VIN range from 4.75 to 25V. The standby LDO should be bypassed with a minimum of 2.2uF ceramic capacitor. ENABLING, DISABLING AND RESET The XRP7713 is enabled via raising the ENABLE Pin high. The chip can then be disabled by lowering the same ENABLE Pin. There is also the capability for resetting the Chip via an I2C SOFTRESET Command. For enabling a specific channel, there are several ways that this can be achieved. The chip can be configured to enable a channel at start-up as the default configuration residing in the non-volatile configuration memory of the IC. The channels can also be enabled using GPIO pins and/or an I2C Bus serial command. The registers that control the channel enable functions are the SET_EN_CONFIG and SET_CH_EN_I2C. INTERNAL GATE DRIVERS The XRP7713 integrates Internal Gate Drivers for all 4 PWM channels. These drivers are optimized to drive both high-side and low side N-MOSFETs for synchronous operations. Both high side and low side drivers have the capability of driving 1nF load with 30ns rise and fall time. The drivers have built-in non-overlapping circuitry to prevent simultaneous conduction of the two MOSFETs. The built-in non-overlapping feature is disabled when the programmable dead time is selected. PROGRAMMABLE DEAD TIME The programmable dead time feature provides customers the flexibility to optimize the system performance over PWM switching frequency, efficiency and component selections. There are three registers to control the dead time. The programmable dead time feature is enabled in the SET_CONTROL_BIT_REG register. If disabled, the built-in dead time control inside the driver will take over. The dead time between the turn off of the low side MOSFET and the turn on of high side MOSFET is controlled by the SET_DT_RISE_CHx. On the other hand, the dead time between the turn off of high side MOSFET and the turn on of the low side MOSFET is controlled by SET_DT_FALL_CHx. The actual LSB of the registers is variable depending on the switching frequency. 𝑆𝑡𝑒𝑝 𝑆𝑖𝑧𝑒 (𝐿𝑆𝐵) = © 2010 Exar Corporation 1 𝑃𝑊𝑀𝑓 × 256 14/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller FAULT HANDLING While the chip is operating there are four different types of fault handling: • • • • Under Voltage Lockout (UVLO) monitors the input voltage to the chip, and the chip will shutdown all channels if the voltage drops to critical levels. Over Temperature Protection (OTP) monitors the temperature of the chip, and the chip will shutdown all channels if the temperature rises to critical levels. Over Voltage Protection (OVP) monitors the voltage of channel and will shutdown the channel if it surpasses its voltage threshold. Over Current Protection (OCP) monitors the current of a channel, and will shutdown the channel if it surpasses its current threshold. The channel will be automatically restarted after a 200ms delay. Under Voltage Lockout (UVLO) The under voltage can be sensed on VIN. The SET_UVLO_WARN_VINx register that sets the under voltage warning set point condition at 100mV increments. When the warning threshold is reached, the Host is informed via a GPIO or by reading the READ_WARN_FLAG register. The SET_UVLO_TARG_VIN1 register that controls the under voltage fault set point condition at 100mV increments. This fault condition will be indicated in the READ_FAULT_WARN register. When an under voltage fault condition occurs, the fault flag register is set and all of the XRP7713 outputs are shut down. The measured input voltages can be read back using the READ_VIN1 register, and both registers have a resolution of 100mV per LSB. When the UVLO condition clears (voltage rises above the UVLO Warning Threshold), the chip can be configured to automatically restart. VIN This is a multi-function pin that provides power to both the Standby Linear Regulator and internal linear regulators to generate VCCA, VDD, and the Standby LDO (LDOUT). It is also used as a UVLO detection pin. If VIN falls below its user programmed limit, all channels are shut down. Temperature Monitoring and Over Temperature Protection (OTP) • Reading the junction temperature This register allows the user to read back the temperature of the IC. The temperature is expressed in Kelvin with a maximum range of 520K, a minimum of 200K, and an LSB of 5 degrees K. The temperature can be accessed by reading the READ_VTJ register. • Over Temperature Warning There are also warning and fault flags that get set in the READ_OVV_UVLO_OVT_FLAG register. The warning threshold is configurable to 5 or 10 Degrees C below the fault threshold. When the junction temperature reaches 5 or 10 Degrees C below the user defined set point, the overtemperature warning bit [OTPW] gets set in the READ_OVV_UVLO_OVT_FLAG register to warn the user that the IC might go into an over temperature condition (and shutdown all of the regulators). • Over Temperature Fault If the over temperature condition occurs both the OTP and OTPW bits will be set in the READ_OVV_UVLO_OVT_FLAG register and the IC will shut down all channels (but I2C will remain operational). The actual over temperature threshold can be set by the user by using a 7bit SET_THERMAL_SHDN register with an LSB of 5K. © 2010 Exar Corporation 15/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller If the over temperature fault condition clears, then the IC can be set to restart the chip automatically. The restart temperature threshold can be set by the SET_THERMAL_RESTART register. OUTPUT VOLTAGE SETTING AND MONITORING The Output Voltage setting is controlled by the SET_VOUT_TARGET_CHx register. This register allows the user to set the output voltage with a resolution of 50mV for output voltages between 0 and 2.5V and with a resolution of 100mV for output voltages between 2.6V and 5.1V. Output voltages higher than 5.1V can be achieved by adding an external voltage divider network. The output voltage of a particular channel can be read back using the READ_VOUTx register. Output Voltage from 0.9V to 5.1V Per the equation below, for values between 0.9V and 5.1V the output voltage is equal to the binary number stored in the SET_VOUT_TARGET_CHx register multiplied by 50mV. When programming an output voltage from 2.6V to 5.1V, odd binary values should be avoided. As a result, the set resolution for an output voltage higher than 2.5V is 100mV. 𝑉𝑂𝑈𝑇 = 𝑆𝐸𝑇_𝑉𝑂𝑈𝑇_𝑇𝐴𝑅𝐺𝐸𝑇_𝐶𝐻𝑋 × 50𝑚𝑉 Output VOUT Higher Than 5.1V To set the output voltage higher than 5.1V, the user needs to add an external voltage divider. The resistors used in the voltage divider should be below 10kΩ. The SET_VOUT_TARGET_CHx register should be set to 0x32 which is equivalent to an output voltage of 2.5V without the external divider network. The output voltage regulation in this case might exceed 2% due to extra error from the resistor divider. R1 and R2 follows the definition below. Vout>5.1V R1 Voutx pin R2 Fig. 224: External divider network for high output voltage 𝑉𝑂𝑈𝑇 = � 𝑅1 + 1� × 𝑆𝐸𝑇_𝑉𝑂𝑈𝑇_𝑇𝐴𝑅𝐺𝐸𝑇_𝐶𝐻𝑋 × 50𝑚𝑉 𝑅2 Output Voltage Lower Than 0.9V The XRP7713 can be programmed to regulate an output voltage lower than 0.9V. However, in this case the specification of ±20mV output voltage accuracy is not guaranteed. OVER-VOLTAGE PROTECTION (OVP) The Over-Voltage Protection (OVP) SET_OVVP_REGISTER sets the over-voltage condition in predefined steps per channel. The over-voltage protection is always active even during soft-start condition. When the over-voltage condition is tripped, the controller will shut down the channel. When the channel is shut down the controller will then set corresponding OVP Fault bits in the READ_OVV_UVLO_OVT_FLAG register. The VOUT OVP Threshold is 150mV to 300mV above nominal VOUT for a Voltage Target of 2.5V or less. For the Voltage Target of 2.6V to 5.1V, the VOUT OVP Threshold is 300mV to 600mV. © 2010 Exar Corporation 16/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Once the over-voltage Channel is disabled, the controller will check the SET_FAULT_RESP_CONFIG_LB and SET_FAULT_RESP_CONFIG_HB to determine whether there are any “following” channels that need to be shut down. Any following channel will be disabled when the channel with the Over Voltage Fault is disabled. The channel(s) will remain disabled, until the Host takes action to enable the channel(s). Any of the fault and warning conditions can also be configured to be represented using the general purpose input output pins (GPIO) to use as an interface with non I2C compatible devices. For further information on this topic see the “GPIO Pins” Section. During OVP fault shutdown of the channel, the customer has the option to choose two types of shutdown for each channel. The first shutdown is ‘passive shutdown’ where the IC merely stops outputting pulses. The second shutdown is a ‘brute force’ shutdown where the GL remains on as the channel reaches its discharged voltage. Note that if the ‘brute force’ method is chosen, then GL will permanently remain high until the channel is re-enabled. OUTPUT CURRENT SETTING AND MONITORING XRP7713 utilizes a low side MOSFET Rdson current sensing technique. The voltage drop on Rdson is measured by dedicated current ADC. The ADC results are compared to a maximum current threshold and an over-current warning threshold to generate the fault and warning flags. Maximum Output Current The maximum output current is set by the SET_VIOUT_MAX_CHx register and SET_ISENSE_PARAM_CHx register. The SET_VIOUT_MAX_CHx register is an 8 bit register. Bits [5:0] set the maximum current threshold and bits [7:6] set the over-current warning threshold. The LSB for the current limit register is 5 mV and the allowed voltage range is between 0 and 315mV. To calculate the maximum current limit, the user needs to provide the MOSFET Rdson. The maximum current can be calculated as: 𝐼𝑂𝑈𝑇𝑀𝐴𝑋 = 𝑉𝑠𝑒𝑛𝑠𝑒 𝑅𝑑𝑠𝑜𝑛 × 𝐾𝑡 Where Kt is the temperature coefficient of the MOSFET Rdson; Vsense is the voltage across Rdson; IOUTMAX is the maximum output current. Over-Current Warning The XRP7713 also offers an Over-Current warning flag. This warning flag resides in the READ_OVC_FLAG register. The warning flag bit will be set when the output current gets to within a specified value of the output current limit threshold enabling the host to reduce power consumption. The SET_VIOUT_MAX_CHx register allows the warning flag threshold to be set 10mV, 20mV, 30mV or 40mV below VIOUT_MAX. The warning flag will be automatically cleared when the current drops below the warning threshold. Over-Current Fault Handling When an over-current condition occurs, PWM drivers in the corresponding channels are disabled. After a 200ms timeout, the controller is re-powered and soft-start is initiated. When the overcurrent condition is reached the controller will check the SET_FAULT_RESP_CONFIG_LB and SET_FAULT_RESP_CONFIG_HB to determine whether there are any “following” channels that need to be similarly restarted. The controller will also set the fault flags in READ_OVC_FAULT_WARN register. © 2010 Exar Corporation 17/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Typically the over-current fault threshold would be set to 130-140% of the maximum desirable output current. This will help avoid any over-current conditions caused by transients that would shut down the output channel. CHIP OPERATION AND CONFIGURATION SOFT-START The SET_SS_RISE_CHx register is a 16 bit register which specifies the soft-start delay and the ramp characteristics for a specific channel. This register allows the customer to program the channel with a 250µs step resolution and up to a maximum 16ms delay. Bits [15:10] specify the delay after enabling a channel but before outputting pulses; where each bit represents 250µs steps. Bits [9:0] specify the rise time of the channel; these 10 bits define the number of microseconds for each 50mV increment to reach the target voltage. Enable Signal Vout RISE TIME DELAY Bit [10:15] Bit [0:9] SS_RISE_CHx REGISTER Fig. 235: Channel Power Up Sequence © 2010 Exar Corporation 18/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller SOFT-STOP The SET_PD_FALL_CHx register is a 16 bit register. This register specifies the soft-stop delay and ramp (fall-time) characteristics for when the chip receives a channel disable indication from the Host to shutdown the channel. Bits [15:10] specify the delay after disabling a channel but before starting the shutdown of the channel; where each bit represents 250µs steps. Bits [9:0] specify the fall time of the channel; these 10 bits define the number of microseconds for each 50mV increment to reach the discharge threshold. Enable Signal Vout Fall Time DELAY Bit [0:9] Bit [10:15] PD_DELAY_CHx REGISTER Fig. 246: Channel Soft-Stop Sequence POWER GOOD FLAG The XRP7713 allows the user to set the upper and lower bound for a power good signal per channel. The SET_PWRG_TARG_MAX_CHx register sets the upper bound, the SET_PWRG_TARG_MIN_CHx register sets the lower bound. Each register has a 20mV LSB resolution. When the output voltage is within bounds the power good signal is asserted high. Typically the upper bound should be lower than the over-voltage threshold. In addition, the power good signal can be delayed by a programmable amount set in the SET_PWRGD_DLY_CHx register. The power good delay is only set after the soft-start period is finished. If the channel has a precharged condition that falls into the power good region, a power good flag is not set until the softstart is finished. PWM SWITCHING FREQUENCY The PWM switching frequency is set by choosing the corresponding oscillator frequency and clock divider ratio in the SET_SW_FREQUENCY register. Bits [6:4] set the oscillator frequency and bits [2:0] set the clock divider. The tables below summarize the available Main Oscillator and PWM switching frequency settings in the XRP7713. Main Oscillator Frequency SET_SW_FREQUENCY[6:4] 000 Main Oscillator Frequency Ts 48MHz 20.8ns © 2010 Exar Corporation 001 010 011 100 44.8MHz 41.6MHz 38.4MHz 35.2MHz 22.3ns 24ns 26ns 28.4ns 19/29 101 110 111 32MHz 31.25ns 28.8Mhz 34.7ns 25.6MHz 39ns Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller PWM Switching Frequency SET_SW_FREQUENCY[6:4] SET_SW_FREQUENCY[2:0] 000 001 010 011 100 101 110 111 000 001 010 011 100 101 110 111 NA 1.5MHz 1.0MHz 750KHz 600KHZ 500KHz 429KHZ 375KHz NA 1.4MHz 933KHz 700KHz 560KHz 467KHZ 400KHZ 350KHz NA 1.3MHz 867KHz 650KHz 520KHz 433KHz 370KHz 325KHz NA 1.2MHz 800KHz 600KHz 480KHz 400KHz 343KHz 300KHz NA 1.1MHz 733KHz 550KHz 440KHz 367KHz 314KHz NA NA 1.0MHz 667KHz 500KHz 400KHz 333KHz NA NA NA 900KHz 600KHz 450KHz 360KHz 300KHz NA NA NA 800KHz 533KHz 400KHz 320KHz NA NA NA There are a number of options that could result in similar PWM switching frequency as shown above. In general, the chip consumes less power at lower oscillator frequency. When synchronization of the Main Oscillator Frequency to an external system clock is desired, the user must choose the oscillator frequency to be within ±5% of the external clock frequency. A higher Main Oscillator frequency will not improve accuracy or any performance efficiency. Note: It is the intention of the synchronization feature to sync to a system clock or to another compatible Exar device, not the switching frequency. PWM SWITCHING FREQUENCY CONSIDERATIONS There are several considerations when choosing the PWM switching frequency. Minimum On Time Minimum on time determines the minimum duty cycle at the specific switching frequency. The minimum on time for the XRP7713 is 40ns. 𝑀𝑖𝑛𝑖𝑚𝑢𝑚 𝐷𝑢𝑡𝑦 𝐶𝑦𝑐𝑙𝑒% = 𝑀𝑖𝑛𝑖𝑚𝑢𝑚 𝑜𝑛𝑡𝑖𝑚𝑒 × 𝑃𝑊𝑀 𝐹𝑟𝑒𝑞𝑢𝑒𝑛𝑐𝑦 × 100 As an example the minimum duty cycle is 4% for 1MHz PWM frequency. This is important since the minimum on time dictates the maximum conversion ratio that the PWM controller can achieve. Maximum Duty Cycle 𝑀𝑖𝑛𝑖𝑚𝑢𝑚 𝐷𝑢𝑡𝑦 𝐶𝑦𝑐𝑙𝑒% > 𝑉𝑜𝑢𝑡 𝑉𝑖𝑛𝑚𝑎𝑥 The maximum duty cycle is dictated by the minimum required time to sample the current when the low side MOSFET is on, this depends on the frequency of the main oscillator and the selected PWM frequency. It is best to choose the highest main oscillator frequency available for any specific PWM frequency. The maximum duty cycle for each PWM frequency is shown in the table below: Main Oscillator Frequency Maximum Duty Cycle 48MHz 78% 86% 84% 89% 88% 88% 86% 1.5MHz 1.0MHz 750KHz 600KHZ 500KHz 429KHZ 375KHz 44.8MHz 41.6MHz 38.4MHz 35.2MHz 32MHz 28.8Mhz 25.6MHz 1.4MHz 933KHz 700KHz 560KHz 467KHZ 400KHZ 350KHz 1.0MHz 667KHz 500KHz 400KHz 333KHz NA NA 900KHz 600KHz 450KHz 360KHz 300KHz NA NA 800KHz 533KHz 400KHz 320KHz NA NA NA 1.3MHz 867KHz 650KHz 520KHz 433KHz 370KHz 325KHz 1.2MHz 800KHz 600KHz 480KHz 400KHz 343KHz 300KHz 1.1MHz 733KHz 550KHz 440KHz 367KHz 314KHz NA Fig. 257: PWM Frequency © 2010 Exar Corporation 20/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller The maximum duty cycle obtained from the table above is programmed by the PowerArchitectTM software into each of the channels using the SET_DUTY_LIMITER_CHx register. This ensures that under all conditions (including faults), there will always be sufficient sampling time to measure the output current. When the duty cycle limit is reached, the output voltage will no longer regulate and will be clamped based on the maximum duty cycle limit setting. It is possible for the user to program SET_DUTY_LIMITER_CHx register to a higher value, but the OCP Fault and OCP WARN flags should then be ignored. Efficiency The PWM Switching frequency plays an important role on overall power conversion efficiency. As the switching frequency increase, the switching losses also increase. Please see the APPLICATION INFORMATION, Typical Performance Data for further examples. Component Selection and Frequency Typically the components become smaller as the frequency increases, as long as the ripple requirements remain constant. At higher frequency the inductor can be smaller in value and have a smaller footprint while still maintaining the same current rating. FREQUENCY SYNCHRONIZATION FUNCTION AND EXTERNAL CLOCK The user of the XRP7713 can choose to use an external source as the primary clock for the XRP7713. This function can be configured using the SET_SYNC_MODE_CONFIG register. This register sets the operation of the XRP7713 when an external clock is required. By selecting the appropriate bit combination the user can configure the IC to function as a master or a slave when two or more XRP7713s are used to convert power in a system. Automatic clock selection is also provided to allow operation even if the external clock fails by switching the IC back to an internal clock. External Clock Synchronization Even when configured to use an external clock, the chip initially powers up with its internal clock. The user can set the percent target that the frequency detector will use when comparing the internal clock with the clock frequency input on the GPIO pin. If the external clock frequency is detected to be within the window specified by the user, then a switchover will occur to the external clock. If the IC does not find a clock in the specified frequency target range then the external clock will not be used and the IC will run on the internal clock that was specified by the user. If the external clock fails the user can chose to have the internal clock take over, using the automatic switch back mode in the SET_SYNC_MODE_CONFIG register. CLK_IN GPIO1 XRP7713 Configured for external clock use Fig. 268:XRP7713 Configured For External Clock Use © 2010 Exar Corporation 21/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Synchronized Operation as a Master and Slave Unit Two XRP7713s can be synchronized together. This Master-Slave configuration is described below. • Master When the XRP7713 powers up as a master unit after the internal configuration memory is loaded the unit will send CLK_OUT and SYNC_OUT signals to the slave on the preconfigured GPIO pins. • Slave When powering in sync mode the slave unit will initially power up with its internal clock to transfer the configuration memory. Once this transfer occurs, then the unit is set to function as a slave unit. In turn the unit will take the external clock provided by the master to run as its main internal clock. GPIO1 CLK_OUT GPIO2 CLK_IN SYNC_OUT GPIO1 SYNC_IN XRP7713 configured as a master GPIO2 XRP7713 configured as a slave Fig. 279: Master/Slave Configuration of the XRP7713 External Clock Synchronization Master Slave combination When an external clock is used, the user will need to setup the master to also have an external clock in function. All of the same rules apply as in the External clock synchronization, Synchronized operation as a Slave unit section of this document. There are two ways of synchronizing this, either the external clock going to both Master/Slave CLK_IN, or CLK_IN can go to the Master, and the Master can synchronize SYNC_OUT and CLK_OUT to the Slave. CLK_IN CLK_IN GPIO1 GPIO2 SYNC_OUT XRP7713 Configured as a master with external clock sync SYNC_IN GPIO1 GPIO2 XRP7713 configured as slave Fig. 3028: External Clock Synchronization Master Slave Combination © 2010 Exar Corporation 22/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller CLK_IN GPIO3 GPIO1 GPIO2 CLK_IN CLK_OUT SYNC_OUT SYNC_IN XRP7713 Configured as a master with external clock sync GPIO1 GPIO2 XRP7713 configured as slave Fig. 291: Alternative External clock synchronization Master Slave combination PHASE SHIFT Each switching channel is configured to run with a phase shift of 90 degrees. GPIO PINS The General Purpose Input Output (GPIO) Pins are the basic interface between the XRP7713 and the system. Although all of the stored data within the IC can be read back using the I2C bus it is sometimes convenient to have some of those internal register to be displayed and or controlled by a single data pin. Besides simple input output functions the GPIO pins can be configured to serve as external clock inputs. These pins can be programmed using OTP bits or can be programmed using the I2C bus. This GPIO_CONFIG register allows the user close to 100 different configuration functions that the GPIO can be programmed to do. NOTE: the GPIO Pins (and all I/Os) should NOT be driven without a 10K resistor when VIN is not being applied to the IC. GPIO Pins Polarity The polarity of the GPIO pin can be set by using the GPIO_ACT_POL register. This register allows any GPIO pin whether configured as an input or output to change polarity. Bits [5:0] are used to set the polarity of GPIO 1 though 5. If the IC operates in I2C mode, then the commands for Bits [5:4] are ignored. Supply Rail Enable Each GPIO can be configured to enable a specific power rail for the system. The GPIOx_CFG register allows a GPIO to enable/disable any of the following rails controlled by the chip: • • • A single buck power controller The Standby LDO Any mix of the Standby LDO and power controller(s) When the configured GPIO is asserted externally, the corresponding rails will be enabled, and they will be similarly disabled when the GPIO is de-asserted. This supply enabling/disabling can also be controlled through the I2C interface. Power Good Indicator The GPIO pins can be configured as Power Good indicators for one or more rails. The GPIO pin is asserted when all rails configured for this specific IO are within specified limits for regulation. This information can also be found in the READ_PWRGD_SS_FLAG status register. © 2010 Exar Corporation 23/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Fault and Warning Indication The GPIOs can be configured to signal Fault or Warning conditions when they occur in the chip. Each GPIO can be configured to signal one of the following: • • • • • • OCP Fault on Channel 1 - 3 OCP Warning on Channel 1 - 3 OVP Fault on Channel 1 – 3 UVLO Fault on VIN UVLO Warning on VIN Over Temperature Fault or Warning I2C COMMUNICATION The I2C communication is standard 2-wire communication available between the Host and the IC. The communication has the option of enabling Packet Error Checking in order to deal with noisy environments where bit-errors could occur in the communication. This packet error checking is a CRC-8 code appended to all communication between the Host and the IC. Each XRP7713 in an I2C -bus system is activated by sending a valid address to the device. The address always has to be sent as the first byte after the start condition in the I2C -bus protocol LSB MSB 6 5 4 3 2 1 0 R/W Fig. 32: Alignment of I2C address in 8 bit byte There is one address byte required since 7-bit addresses are used. The last bit of the address byte is the read/write-bit and should always be set according to the required operation. This 7-bit I2C address is stored in the NVM. One can program a blank device with the 7-bit Slave address or select one of the preprogrammed options. The 7-bit address plus the R/W bit create an 8-bit data value that is sent on the bus. The XRP7713ILB-0X10-F has an I2C address of 0x10. The internal registers are written by sending a data value of 0x20 and read by sending a data value of 0x21. This reflects the address being shifted one bit to the left and the least significant bit being set to reflect a read or write operation in order to stuff the byte correctly. The second byte sent to the XRP7713 is the location of a specific register. Using GPIO3 to select I2C Address GPIO3 may be used to change the LSB of the 7-bit address. This option can be enabled within the PowerArchitectTM software by checking the “Use GPIO3 to control LSB of I2C address” box at the top right of the “Digital Design” tab. More about the use of this option and other methods of changing the default I2C address of the part are available in ANP-31 “PowerXR Configuration and Programming”. © 2010 Exar Corporation 24/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller EXTERNAL COMPONENT SELECTION Inductor Selection Select the Inductor for inductance L and saturation current Isat. Select an inductor with Isat higher than the programmed over current limit. Calculate inductance from: Where: 𝐿= (𝑉𝑖𝑛 − 𝑉𝑜𝑢𝑡) × 𝑉𝑜𝑢𝑡 1 1 × × 𝑓𝑠 𝐼𝑟𝑖𝑝 𝑉𝑖𝑛 Vin is the converter input voltage Vout is the converter output voltage fs is the switching frequency Irip is the inductor peak-to-peak current ripple (nominally set to 30% of Iout) Keep in mind that a higher Irip results in a smaller inductance value which has the advantages of smaller size, lower DC equivalent resistance (DCR), and allows the use of a lower output capacitance to meet a given step load transient. A higher Irip, however, increases the output voltage ripple, requires higher saturation current limit, and increases critical conduction. Notice that this critical conduction current is half of Irip. Capacitor Selection • Output Capacitor Selection Select the output capacitor for voltage rating, capacitance and Equivalent Series Resistance (ESR). Nominally the voltage rating is selected to be at least twice as large as the output voltage. Select the capacitance to satisfy the specification for output voltage overshoot/undershoot caused by the current step load. A sudden decrease in the load current forces the energy surplus in the inductor to be absorbed by Cout. This causes an overshoot in output voltage that is corrected by power switch reduced duty cycle. Use the following equation to calculate Cout: 𝐶 =𝐿× Where: (𝐼2 − 𝐼1 )2 𝑉𝑂𝑆 2 − 𝑉𝑂𝑈𝑇 2 L is the output inductance I2 is the step load high current I1 is the step load low current Vos is output voltage including the overshoot Vout is the steady state output voltage Or it can be expressed approximately by Here, 𝐶 =𝐿× (𝐼2 − 𝐼1 )2 2 × 𝑉𝑜𝑢𝑡 − ∆𝑉 ∆V = Vos − Vout is the overshoot voltage deviation. © 2010 Exar Corporation 25/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Select ESR such that output voltage ripple (Vrip) specification is met. There are two components in Vrip. First component arises from the charge transferred to and from Cout during each cycle. The second component of Vrip is due to the inductor ripple current flowing through the output capacitor’s ESR. It can be calculated for Vrip: 𝑉𝑟𝑖𝑝 = 𝐼𝑟𝑖𝑝 × �𝐸𝑆𝑅2 + � Where: 2 1 � 8 × 𝐶𝑜𝑢𝑡 × 𝑓𝑠 Irip is the inductor ripple current fs is the switching frequency Cout is the output capacitance Note that a smaller inductor results in a higher Irip, therefore requiring a larger Cout and/or lower ESR in order to meet Vrip. With the current generation of ultra-low ESR ceramic capacitors it is common to operate with Irip ≥ 30% of Iout. When trying to optimize control loop bandwidth, particularly at switching frequencies below 600kHz, an effective ESR in the range of 7 to 20mohm can help significantly. The Digital Power Studio design tool is used to verify what will work best in your application. • Input Capacitor Selection Select the input capacitor for Voltage, Capacitance, ripple current, ESR and ESL. Voltage rating is nominally selected to be at least twice the input voltage. The RMS value of input capacitor current, assuming a low inductor ripple current, can be approximated as: 𝐼𝑖𝑛 = 𝐼𝑜𝑢𝑡 × �𝐷 × (1 − 𝐷) Where: Iin is the RMS input current Iout is the DC output current D is the duty cycle In general, the total input voltage ripple should be kept below 1.5% of VIN. The input voltage ripple also has two major components: the voltage drop on the main capacitor ∆VCin and the voltage drop due to ESR - ∆VESR . The contribution to Input voltage ripple by each term can be calculated from: ∆VCin = I outVout (Vin − Vout ) f s C inVin2 ∆VESR = ESR ⋅ ( I out + 0.5 I rip ) Total input voltage ripple is the sum of the above: ∆VTot = ∆VCin + ∆VESR © 2010 Exar Corporation 26/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller Power MOSFETs Selection Selecting MOSFETs with lower Rdson reduces conduction losses at the expense of increased switching losses. Conduction losses are expressed by the two following equations. High Side MOSFET Conducted Loss: 2 Pcond = I out ⋅ Rdson ⋅ Vout Vin Low Side MOSFET Conducted Loss: V 2 Pcond = I out ⋅ Rdson ⋅ 1 − out Vin The MOSFET’s junction temperature can be estimated from: T j = 2 Pcond Rthja + Tambient This assumes that the switching loss is the same as the conduction loss. Rthja is the total MOSFET thermal resistance from junction to ambient. LAYOUT GUIDELINES Refer to application note ANP-32 “Practical Layout Guidelines for PowerXR Designs”. © 2010 Exar Corporation 27/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller PACKAGE SPECIFICATION © 2010 Exar Corporation 32-PIN 5MMX5MM TQFN 28/29 Rev. 1.1.1 XRP7713 Three Channel Digital PWM Step Down Controller REVISION HISTORY Revision 1.0.0 1.0.3 Date Description February 2010 Initial Release March 2010 Updated Diagrams 1.1.0 09/30/2010 Added references to PowerArchitect™. Revised θJA, Revised I2C Communication section. Added “Power-Up and Sequencing Requirements”. Changed schematics to include EN pin sequencing. Corrected conditions for LDO OUTPUT voltage at 5V. Added EN Pin threshold specification. Changed input voltage operating range. Added GPIO3 I2C address selection. Other minor modifications to wording. Added ESD rating. Added Negative LX transient specification. 1.1.1 12/07/2010 Package drawing updated in revision 1.1.0 for legibility was incorrect. In particular, D2 and E2. This has been corrected FOR FURTHER ASSISTANCE Email: [email protected] Exar Technical Documentation: http://www.exar.com/TechDoc/default.aspx? EXAR CORPORATION HEADQUARTERS AND SALES OFFICES 48720 Kato Road Fremont, CA 94538 – USA Tel.: +1 (510) 668-7000 Fax: +1 (510) 668-7030 www.exar.com NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. or its in all Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. © 2010 Exar Corporation 29/29 Rev. 1.1.1