HMC1013LP4E v00.0511 Typical Applications Features The HMC1013LP4E is ideal for: High Logging Range: 67 dB (-62 to +5 dBm) • EW, ELINT & IFM Receivers Output Frequency Flatness: ±2 dB • DF Radar Systems Log Linearity: ±2 dB • ECM Systems Fast Rise/Fall Times: 5/15 ns • Broadband Test & Measurement Single Positive Supply: +3.3V • Power Measurement & Control Circuits ESD Sensitivity (HBM): Class 1A • Military & Space Applications 24 Lead 4x4mm SMT Package: 16mm2 Functional Diagram General Description The HMC1013LP4E is a Successive Detection Log Video Amplifier which operates from 0.5 to 18.5 GHz. The HMC1013LP4E provides a logging range of 67 dB. This device offers typical fast rise/fall times of 5/15 ns and a superior delay time of only 10 ns. The HMC1013LP4E log video output slope is typically 15 mV/dB. Maximum recovery times are less than 40 ns. The HMC1013LP4E is available in a highly compact 4x4 mm SMT plastic package and is ideal for high speed channelized receiver applications. SDLVAs - SMT 11 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Electrical Specifications, TA = +25 °C Vcc1 = Vcc2 = Vcc3= +3.3V, EN=3.3V Parameter Conditions Input Frequency Range [1] Frequency Flatness Typ. Units 0.5 - 18.5 GHz ±2 dB Pin = -60 to +5 dBm ±2 dB ±2 dB Minimum Logging Range to ±3 dB error -62 dBm Maximum Logging Range to ±3 dB error +5 dBm Log Linearity Log Linearity over Temperature 8 dB Log Video Minimum Output Voltage Input Return Loss 0.9 V Log Video Maximum Output Voltage 1.9 V Log Video Output Rise Time 10% to 90% 5 ns Log Video Output Fall Time 90% to 10% 15 ns @ 10 GHz 38 ns 15 mV/dB 6.2 µV/dB°C 10 ns Supply Current (Icc1) 7 mA Supply Current (Icc2) 90 mA Supply Current (Icc3) 86 mA Log Video Recovery Time Log Video Output Slope Log Video Output Slope Variation over Temperature Log Video Propagation Delay @ 10 GHz [1] Video output load should be 1k Ohm or higher. 11 - 1 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Error Flatness vs. Input Power Over Frequency [1] [2] VIDEO OUT & Error vs. Input Power, Fin = 500 MHz 8 1.6 0 -2 1 1.2 0 0.8 -6 0.6 -8 -70 0.4 -50 -40 -30 -20 -10 0 10 -70 20 -1 1 -4 -60 -4 -60 -50 4 1.8 2 1.6 1.2 0 -1 1 Ideal Video Out +25C Video Out +85C Video Out -40C 0.4 -60 -50 -40 -30 -20 -10 0 10 4 -1 1 -4 0.4 -70 3 1.8 2 1.6 1 Ideal Video Out +25C Video Out +85C Video Out -40C 0.4 -30 -20 -10 -3 -4 -60 -50 -40 -30 -20 -10 0 10 20 0 10 INPUT POWER (dBm) 20 4 ERR +25C ERR +85C ERR -40C 3 2 1.4 1 1.2 0 -1 1 -2 0.8 -3 0.6 -4 0.4 -70 ERROR (dB) -1 VIDEO OUT (V) 2 ERROR (dB) VIDEO OUT (V) 4 0 -40 -2 Ideal Video Out +25C Video Out +85C Video Out -40C VIDEO OUT & Error vs. Input Power, Fin = 10 GHz 1.2 -50 2 0 0.6 1 -60 3 1.2 0.8 1.4 -70 20 INPUT POWER (dBm) ERR +25C ERR +85C ERR -40C 0.6 10 1 -3 20 2 0.8 0 1.4 -2 VIDEO OUT & Error vs. Input Power, Fin = 6 GHz 1.6 -10 ERR +25C ERR +85C ERR -40C INPUT POWER (dBm) 1.8 -20 ERROR (dB) 1 ERROR (dB) VIDEO OUT (V) 3 1.4 -70 -30 2 VIDEO OUT (V) ERR +25C ERR +85C ERR -40C 0.6 -40 VIDEO OUT & Error vs. Input Power, Fin = 2 GHz 2 0.8 11 -3 INPUT POWER (dBm) VIDEO OUT & Error vs. Input Power, Fin = 1 GHz 1.6 -2 Ideal Video Out +25C Video Out +85C Video Out -40C INPUT POWER (dBm) 1.8 2 1.4 ERROR (dB) 2 3 ERR +25C ERR +85C ERR -40C 1.8 VIDEO OUT (V) 4 10 GHz 14 GHz 18 GHz SDLVAs - SMT 6 ERROR (dB) 4 2 1 GHz 2 GHz 6 GHz -2 Ideal Video Out +25C Video Out +85C Video Out -40C -3 -4 -60 -50 -40 -30 -20 -10 0 10 20 INPUT POWER (dBm) [1] An average ideal line is used to calculate error curves. [2] At 25°C. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 11 - 2 HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz VIDEO OUT & Error vs. Input Power, Fin = 18 GHz VIDEO OUT & Error vs. Input Power, Fin = 14 GHz ERR +25C ERR +85C ERR -40C 1.8 3 1.8 2 1.6 1.4 1 1.2 0 0 -2 0.8 -3 0.6 -4 0.4 -70 -60 -50 -40 -30 -20 -10 0 10 -1 1 20 -2 Ideal Video Out +25C Video Out +85C Video Out -40C -3 -4 -70 -60 -50 -40 INPUT POWER (dBm) SDLVAs - SMT 2 1.2 0.8 0.4 3 1 -1 0.6 ERR +25C ERR +85C ERR -40C 1.4 1 Ideal Video Out +25C Video Out +85C Video Out -40C 4 -30 -20 -10 0 10 20 INPUT POWER (dBm) VIDEO OUT & Error vs. Input Power, Fin = 20 GHz 4 2 ERR +25C ERR +85C ERR -40C 3 1.6 2 1.4 1 1.2 0 -1 1 -2 0.8 Ideal Video Out +25C Video Out +85C Video Out -40C 0.6 -3 -4 0.4 -70 ERROR (dB) VIDEO OUT (V) 1.8 -60 -50 -40 -30 -20 -10 0 10 20 INPUT POWER (dBm) VIDEO OUT vs. Frequency Over Input Power & Temperature VIDEO OUT vs. Frequency Over Input Power & Bias Voltage 1.8 1.8 1.7 1.7 -10 dBm 1.5 1.4 -25 dBm 1.3 1.2 +25C +85C -40C 0 2 4 6 8 10 12 14 FREQUENCY (GHz) 11 - 3 1.5 1.4 -25 dBm 1.3 1.2 -40 dBm 1.1 1 -10 dBm 1.6 VIDEO OUT (V) VIDEO OUT (V) 1.6 -40 dBm 3.45V 3.30V 3.15V 1.1 16 18 20 1 0 2 4 6 8 10 12 14 16 18 20 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] ERROR (dB) 11 2 ERROR (dB) VIDEO OUT (V) 1.6 4 VIDEO OUT (V) 2 HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Rise Time for Various Frequencies @ 0 dBm Fall Time for Various Frequencies @ 0 dBm 2.2 2.2 1.8 VIDEO OUT (V) 1.6 1.4 1.6 1.4 1.2 1.2 1 1 0.8 0 20 40 60 80 100 120 140 160 180 200 2 GHz 10 GHz 18 GHz 1.8 0.8 0 10 20 40 Absolute Maximum Ratings Input Return Loss vs. Frequency 0 Vcc +3.6V Enable +3.6V RF Input Power +13 dBm -10 Junction Temperature 125 °C -15 Continuous Pdiss (T=85 °C) Derate 35.22 mW/°C above 85 °C 1.41 W -20 Thermal Resistance (Rth) (junction to package bottom) 28.4 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1A -5 -25 +25C +85C -40C -30 0 2 4 6 8 10 12 50 11 TIME (ns) TIME (ns) INPUT RETURN LOSS (dB) 30 14 16 18 SDLVAs - SMT VIDEO OUT (V) 2 2 GHz 10 GHz 18 GHz 2 20 FREQUENCY (GHz) ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 11 - 4 HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Outline Drawing SDLVAs - SMT 11 NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY. 3. LEAD AND GROUND PADDLE PLATING: 100% MATTE TIN 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 6. CHARACTERS TO BE HELVETICA MEDIUM, .025 HIGH, WHITE INK, OR LASER MARK LOCATED APPROX. AS SHOWN. 7. PAD BURR LENGTH SHALL BE 0.15mm MAX. PAD BURR HEIGHT SHALL BE 0.05mm MAX. 8. PACKAGE WARP SHALL NOT EXCEED 0.05mm 9. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 10. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN Package Information Part Number Package Body Material Lead Finish HMC1013LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H1013 XXXX [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C 11 - 5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Pin Descriptions Pin Number Function Description 1-2, 7, 9-10, 12-13, 16, 18-19, 21, 23 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3, 5-6, 8, 11 GND These pins and the exposed package bottom must be connected to a high quality RF/DC ground. Interface Schematic 4 RFIN RF Input pin 14, 15 VIDEO_FB VIDEO_OUT Video out and feedback. 17 EN Enable pin, connect to 3.3V supply for normal operation. Total supply current reduced to less than 11mA when EN is set to 0V. 20 VCC3 Bias Supply. Connect supply voltage to these pins with appropriate filtering. See application circuit. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] SDLVAs - SMT 11 11 - 6 HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Pin Descriptions (continued) Pin Number Function Description 22, 24 VCC2, VCC1 Bias Supply. Connect Supply Voltage to these pins with appropriate filtering. Connect Vcc2 with Vcc1. See application circuit. Interface Schematic SDLVAs - SMT 11 Application Circuit Note: Video output load should be 1k Ohm or higher. 11 - 7 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC1013LP4E v00.0511 SUCCESSIVE DETECTION LOG VIDEO AMPLIFIER (SDLVA), 0.5 - 18.5 GHz Evaluation PCB SDLVAs - SMT 11 List of Materials for Evaluation PCB EVAL01-HMC1013LP4E[1] Item Description J1 K-Type Connector J2 SMA Connector J3 - J6 DC Pins C2 47 pF Capacitor, 0402 Pkg. C4 100 pF Capacitor, 0402 Pkg. C5-C7 10 nF Capacitor, 0402 Pkg. C8-C10 4.7 µF Capacitor, Tantalum. R1-R4 0 Ohm Resistor, 0402 Pkg. R5 120 Ohm Resistor, 0402 Pkg. R8 49.9 Ohm Resistor, 0201 Pkg. U1 HMC1013LP4E SDLVA PCB [2] 126093 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. N/C pins should also be connected to ground. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or Arlon 25 FR For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 11 - 8