HITTITE HMC451LP3

HMC451LP3 / 451LP3E
v00.0808
Amplifiers - Linear & Power - SMT
9
Typical Applications
Features
The HMC451LP3(E) is ideal for:
Gain: 18 dB
• Microwave Radio & VSAT
Saturated Power: +21 dBm @ 18% PAE
• Military & Space
Output IP3: +28 dBm
• Test Equipment & Sensors
Single Supply: +5V @ 120 mA
• Fiber Optics
50 Ohm Matched Input/Output
• LO Driver for HMC Mixers
16 Lead 3x3mm SMT Package: 9mm²
Functional Diagram
General Description
The HMC451LP3(E) is an efficient GaAs PHEMT
MMIC Medium Power Amplifier housed in a leadless
RoHS compliant SMT package. Operating between
5 and 18 GHz, the amplifier provides 18 dB of gain,
+21 dBm of saturated power and 18% PAE from a
single +5V supply. This 50 Ohm matched amplifier
does not require any external components and the
RF I/O’s are DC blocked, making it an ideal linear
gain block or LO driver for HMC mixers. The
HMC451LP3(E) eliminates the need for wire bonding,
and allows the use of surface mount manufacturing
techniques.
Electrical Specifications, TA = +25° C, Vdd1 = Vdd2 = +5V
Parameter
Min.
Frequency Range
Gain
Typ.
Max.
Min.
5 - 16
15
Gain Variation Over Temperature
18
0.02
Typ.
Max.
16 - 18
12.5
0.03
GHz
16
0.02
Units
dB
0.03
dB/ °C
Input Return Loss
13
13
dB
Output Return Loss
12
8
dB
19
dBm
Output Power for 1 dB
Compression (P1dB)
16.5
19.5
16
Saturated Output Power (Psat)
21
20
dBm
Output Third Order Intercept (IP3)
28
25
dBm
Noise Figure
7
7
Supply Current (Idd)
9-1
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
120
150
120
dB
150
mA
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC451LP3 / 451LP3E
v00.0808
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
Broadband Gain & Return Loss
Gain vs. Temperature
25
24
20
16
S21
S11
S22
5
GAIN (dB)
-5
12
-15
4
-25
0
4
6
8
10
12
14
16
18
20
4
6
8
FREQUENCY (GHz)
12
14
16
18
20
Output Return Loss vs. Temperature
0
0
+25C
+85C
-40C
-5
RETURN LOSS (dB)
-5
RETURN LOSS (dB)
10
FREQUENCY (GHz)
Input Return Loss vs. Temperature
-10
-15
-20
-10
-15
+25C
+85C
-40C
-20
-25
-25
4
6
8
10
12
14
16
18
20
4
6
8
FREQUENCY (GHz)
24
24
20
20
Psat (dBm)
28
16
+25C
+85C
-40C
8
12
14
16
18
20
16
18
20
Psat vs. Temperature
28
12
10
FREQUENCY (GHz)
P1dB vs. Temperature
P1dB (dBm)
9
+25C
+85C
-40C
8
16
12
+25C
+85C
-40C
8
4
Amplifiers - Linear & Power - SMT
RESPONSE (dB)
15
4
0
0
4
6
8
10
12
14
FREQUENCY (GHz)
16
18
20
4
6
8
10
12
14
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
9-2
HMC451LP3 / 451LP3E
v00.0808
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
Power Compression @ 17 GHz
Power Compression @ 10 GHz
20
16
Pout (dBm)
Gain (dB)
PAE (%)
12
8
4
-14
-10
-6
-2
2
20
16
Pout (dBm)
Gain (dB)
PAE (%)
12
8
4
0
-18
6
-14
-10
INPUT POWER (dBm)
-2
2
6
Noise Figure vs. Temperature
12
32
30
NOISE FIGURE (dB)
10
28
IP3 (dBm)
-6
INPUT POWER (dBm)
Output IP3 vs. Temperature
26
24
+25C
+85C
-40C
22
8
6
+25C
+85C
-40C
4
20
2
4
6
8
10
12
14
16
18
4
20
6
8
FREQUENCY (GHz)
12
14
16
18
20
Reverse Isolation vs. Temperature
0
21
-10
ISOLATION (dB)
22
20
19
18
17
10
FREQUENCY (GHz)
Gain, P1dB & PSAT
vs. Supply Voltage @ 11 GHz
16
4.5
9-3
Pout (dBm), GAIN (dB), PAE (%)
24
0
-18
GAIN (dB), P1dB (dBm), Psat (dBm)
Amplifiers - Linear & Power - SMT
9
Pout (dBm), GAIN (dB), PAE (%)
24
Gain
P1dB
Psat
+25C
+85C
-40C
-20
-30
-40
-50
-60
5
Vdd (V)
5.5
4
6
8
10
12
14
16
18
20
FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC451LP3 / 451LP3E
v00.0808
Absolute Maximum Ratings
Drain Bias Voltage (Vdd1 = Vdd2)
+5.5V
RF Input Power (RFIN)(Vdd = +5Vdc)
+10 dBm
Channel Temperature
150 °C
Continuous Pdiss (T = 85 °C)
(derate 12.8 mW/°C above 85 °C)
0.83 W
Thermal Resistance
(channel to ground paddle)
78 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
Typical Supply Current vs. Vdd1 = Vdd2
Vdd1 = Vdd2 (V)
Idd1 + Idd2 (mA)
+4.5
120
+5.0
122
+5.5
124
Note: Amplifier will operate over full voltage range shown above
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
9
Amplifiers - Linear & Power - SMT
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC451LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
[1]
HMC451LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
[2]
Package Marking [3]
451
XXXX
451
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
9-4
HMC451LP3 / 451LP3E
v00.0808
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
Pin Descriptions
Pin Number
Amplifiers - Linear & Power - SMT
9
9-5
Function
Description
1, 2, 4 - 9, 11,
12, 14, 16
N/C
This pin may be connected to RF/DC ground.
Performance will not be affected.
3
RFIN
This pin is AC coupled
and matched to 50 Ohms.
10
RFOUT
This pin is AC coupled
and matched to 50 Ohms.
13
Vdd2
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF, 1,000 pF and 2.2 µF are required.
15
Vdd1
Power Supply Voltage for the amplifier. External bypass
capacitors of 100 pF, 1,000 pF and 2.2 µF are required.
GND
Package bottom must be connected to RF/DC ground.
Interface Schematic
Application Circuit
Component
Value
C1, C2
100 pF
C3, C4
1,000 pF
C5, C6
2.2 µF
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC451LP3 / 451LP3E
v00.0808
GaAs PHEMT MMIC MEDIUM
POWER AMPLIFIER, 5 - 18 GHz
Evaluation PCB
List of Materials for Evaluation PCB 120202
Item
Description
J1 - J2
PCB Mount SMA Connector
J3 - J5
DC Pin
C1, C2
100 pF Capacitor, 0402 Pkg.
C3, C4
1000 pF Capacitor, 0603 Pkg.
C5, C6
2.2 µF Capacitor, Tantalum
U1
HMC451LP3(E) Amplifier
PCB [2]
120201 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Arlon 25FR
[1]
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 Ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation board should be mounted to an
appropriate heat sink. The evaluation circuit board
shown is available from Hittite upon request.
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
Amplifiers - Linear & Power - SMT
9
9-6