HITTITE HMC840LP6CE

HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Features
• RF Bandwidth:
1310-1415, 2620-2830, 5240-5660 MHz
• 24-bit Step Size, Resolution 3 Hz typ
• Ultra Low Phase Noise
-110 dBc/Hz in Band Typ.
• Built in Digital Self Test
• Figure of Merit (FOM) -227 dBc/Hz
• Exact Frequency Mode
• 40 Lead 6x6 mm SMT Package: 36 mm2
• <180 fs RMS Jitter
Typical Applications
PLLS WITH INTEGRATED VCO - SMT
7
7-1
• Cellular/4G Infrastructure
• Phased Array Applications
• Repeaters and Femtocells
• DDS Replacement
• Communications Test Equipment
• Very High Data Rate Radios
• CATV Equipment
Functional Diagram
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
General Description
The HMC840LP6CE is a fully functioned Fractional-N Phase-Locked-Loop (PLL) Frequency Synthesizer with an
Integrated Voltage Controlled Oscillator (VCO). The synthesizer consists of an integrated low noise VCO with a triband output, an autocalibration subsystem for low voltage VCO tuning, a very low noise digital Phase Detector (PD),
a precision controlled charge pump, a low noise reference path divider and a fractional divider.
The fractional synthesizer features an advanced delta-sigma modulator design that allows both ultra-fine step sizes
and low spurious products. The phase detector (PD) features cycle slip prevention (CSP) technology to allow faster
frequency hopping times. Ultra low in-close phase noise and low spurious also allows wider loop bandwidths for faster
frequency hopping and low micro-phonics.
Electrical Specifications
VPPCP, VDDCP, VCC1, VCC2 = 5V; RVDD, AVDD, DVDD3V, VCCPD, VCCHF, VCCPS = 3.3V
GNDCP = GNDLS = Ground Paddle = 0V, Min and Max Specified across Temp
Parameter
Condition
Min.
Typ.
Max.
Units
RF Output Characteristics
VCO Frequency at PLL Input
2620
2830
MHz
RF Output Frequency at f VCO/2
1310
1415
MHz
RF Output Frequency at f VCO
2620
2830
MHz
RF Output Frequency at 2f VCO
5240
5660
MHz
Output Power
RF Output Power at f VCO/2
RF Output Power at f VCO
matched at the frequency of
interest, vs temperature
RF Output Power at 2f VCO
8.5
10
11.5
dBm
7
9
11
dBm
-5.5
-3
0.5
dBm
10.5
12.6
15.6
MHz/V
VCO Tuning Sensitivity
Measured at fo, 2V
VCO Supply Pushing
Measured at fo, 2V
1.5
MHz/V
RF Output Fout/2 Harmonic
Doubler Mode
-26
dBc
RF Output 3Fout/2 Harmonic
Doubler Mode
-27
dBc
Harmonics
RF Output 2nd Harmonic
RF Output 5 Fout/2 Harmonic
RF Output 3rd Harmonic
RF Output 7 Fout/2 Harmonic
RF Output 4th Harmonic
fo/2/fo/2fo
-19 / -20 / -25
dBc
Doubler Mode
-41
dBc
fo/2/fo/2fo
-26 / -34 / -42
dBc
Doubler Mode
-66
dBc
fo/2/fo/2fo
-28 / -48 / -61
dBc
RF Divider Characteristics
19-Bit N-Divider Range (Integer)
19-Bit N-Divider Range (Fractional)
Max = 219 - 1
524,287
Fractional nominal divide ratio
varies (-3 / +4) dynamically max
524,283
7
PLLS WITH INTEGRATED VCO - SMT
For theory of operation and register map refer to the “PLLs with Integrated VCOs - RF VCOs Operating Guide”. To
view the Operating Guide, please visit www.hittite.com and choose HMC840LP6CE from the “Search by Part
Number” pull down menu.
REF Input Characteristics
Max Ref Input Frequency
Ref Input Range
AC Coupled
1
Ref Input Capacitance
14-Bit R-Divider Range
1
50
200
MHz
2
3.3
Vp-p
5
pF
16,383
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
7-2
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Electrical Specifications (Continued)
Parameter
Condition
Min.
[1]
Typ.
Max.
Units
Phase Detector (PD)
PD Frequency Fractional Feedback Mode
0.1
100
MHz
PD Frequency Fractional Feedforward Mode
(and Register 6 [17:16] = 10)
0.1
80
MHz
PD Frequency Integer Mode
0.1
125
MHz
2.54
mA
Charge Pump
Output Current
0.02
Charge Pump Gain Step Size
PD/Charge Pump SSB Phase Noise
PLLS WITH INTEGRATED VCO - SMT
7
20
µA
50 MHz Ref, Input Referred
1 kHz
-143
dBc/Hz
10 kHz
Add 1 dB for Fractional
-150
dBc/Hz
100 kHz
Add 3 dB for Fractional
-153
dBc/Hz
Logic Inputs
VIH Input High Voltage
DVDD3V-0.4
DVDD3V
V
VIL Input Low Voltage
0
0.4
V
VOH Output High Voltage
DVDD3V-0.4
DVDD3V
V
VOL Output Low Voltage
0
0.4
V
3.5
V
Logic Outputs
Power Supply Voltages
Analog 3.3V Supplies
Digital Supply
Analog 5V Supplies
AVDD, VCCHF, VCCPS,
VCCPD, RVDD
3.0
3.3
DVDD3V
3.0
3.3
3.5
V
VPPCP, VDDCP, VCC1, VCC2
4.8
5
5.2
V
Power Supply Currents
+5V Analog Charge Pump
VPPCP, VDDCP
5.3
mA
+5V VCO Core and PLL Buffer
VCC2
56
mA
+5V VCO Divider and RF Buffer
VCC1
36
mA
AVDD, VCCHF, VCCPS,
VCCPD, RVDD
41
mA
+3.3V Analog
+3.3V Digital
Power Down - Crystal Off
Power Down - Crystal On, 100 MHz
DVDD3V
6.5
mA
Reg 01h=0,
Crystal Not Clocked
10
µA
Reg 01h=0,
Crystal Clocked 100 MHz
10
200
µA
Power on Reset
Typical Reset Voltage on DVDD
700
mV
250
µs
10 kHz Offset
-88
dBc/Hz
100 kHz Offset
-117
dBc/Hz
1 MHz Offset
-145
dBc/Hz
Min DVDD Voltage for No Reset
Power on Reset Delay
1.5
V
VCO Open Loop Phase Noise at fo/2
[1] This maximum phase detector frequency can only be achieved if the minimum N value is respected. eg. In the case of fractional feedback
mode, the maximum PFD rate = fvco/20 or 100 MHz, whichever is less.
7-3
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]ite.com
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Electrical Specifications (Continued)
Parameter
Condition
Min.
Typ.
Max.
Units
10 MHz Offset
-162
dBc/Hz
100 MHz Offset
-165
dBc/Hz
10 kHz Offset
-82
dBc/Hz
100 kHz Offset
-111
dBc/Hz
1 MHz Offset
-139
dBc/Hz
10 MHz Offset
-158
dBc/Hz
100 MHz Offset
-171
dBc/Hz
10 kHz Offset
-76
dBc/Hz
100 kHz Offset
-105
dBc/Hz
1 MHz Offset
-133
dBc/Hz
10 MHz Offset
-152
dBc/Hz
-158
dBc/Hz
VCO Open Loop Phase Noise at fo
VCO Open Loop Phase Noise at 2fo
Closed Loop Phase Noise PLL + VCO at fvco with 100 KHz BW Loop Filter
Design[3]
Integer, 100 MHz PD
1 kHz Offset
-112
dBc/Hz
Integer, 100 MHz PD
10 kHz Offset
-110
dBc/Hz
Integer, 100 MHz PD
100 kHz Offset
-111
dBc/Hz
Integer, 100 MHz PD
1 MHz Offset
-139
dBc/Hz
Integer, 100 MHz PD
10 MHz Offset
-161
dBc/Hz
Integer, 100 MHz PD
100 MHz Offset
-171
dBc/Hz
-56.5
dBc
Integrated Phase Noise
from 10KHz to 100MHz
129.5
fsec
1 kHz Offset
-111
dBc/Hz
Fractional, 100 MHz PD
10 kHz Offset
-110
dBc/Hz
Fractional, 100 MHz PD
100 kHz Offset
-110
dBc/Hz
RMS Jitter
Fractional, 100 MHz PD
Fractional, 100 MHz PD
1 MHz Offset
-139
dBc/Hz
Fractional, 100 MHz PD
10 MHz Offset
-160
dBc/Hz
Fractional, 100 MHz PD
100 MHz Offset
-171
dBc/Hz
-56.8
dBc
123.8
fsec
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
Closed Loop Phase Noise PLL + VCO at fvco with 178 KHz BW Loop Filter Design[4]
Integer, 100 MHz PD
1 kHz Offset
-113
dBc/Hz
Integer, 100 MHz PD
10 kHz Offset
-118
dBc/Hz
Integer, 100 MHz PD
100 kHz Offset
-112
dBc/Hz
Integer, 100 MHz PD
1 MHz Offset
-138
dBc/Hz
Integer, 100 MHz PD
10 MHz Offset
-160
dBc/Hz
Integer, 100 MHz PD
100 MHz Offset
-171
dBc/Hz
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
-59.7
dBc
89
fsec
Fractional, 100 MHz PD
1 kHz Offset
-111
dBc/Hz
Fractional, 100 MHz PD
10 kHz Offset
-115
dBc/Hz
Fractional, 100 MHz PD
100 kHz Offset
-109
dBc/Hz
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
PLLS WITH INTEGRATED VCO - SMT
100 MHz Offset
7
7-4
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Electrical Specifications (Continued)
Parameter
Fractional, 100 MHz PD
Condition
Min.
Typ.
Max.
Units
1 MHz Offset
-138
dBc/Hz
Fractional, 100 MHz PD
10 MHz Offset
-160
dBc/Hz
Fractional, 100 MHz PD
100 MHz Offset
-171
dBc/Hz
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
-58
dBc
108.7
fsec
-110
dBc/Hz
Closed Loop Phase Noise PLL + VCO at fvco with 71 KHz Loop Filter Design [5]
Integer, 50 MHz PD
7
1 kHz Offset
Integer, 50 MHz PD
10 kHz Offse
-105
dBc/Hz
Integer, 50 MHz PD
100 kHz Offset
-109
dBc/Hz
Integer, 50 MHz PD
1 MHz Offset
-139
dBc/Hz
Integer, 50 MHz PD
10 MHz Offset
-160
dBc/Hz
Integer, 50 MHz PD
100 MHz Offset
-171
dBc/Hz
PLLS WITH INTEGRATED VCO - SMT
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
dBc
fsec
dBc/Hz
Fractional, 50 MHz PD
1 kHz Offset
-108
Fractional, 50 MHz PD
10 kHz Offset
-104
dBc/Hz
Fractional, 50 MHz PD
100 kHz Offset
-109
dBc/Hz
Fractional, 50 MHz PD
1 MHz Offset
-139
dBc/Hz
Fractional, 50 MHz PD
10 MHz Offset
-160
dBc/Hz
Fractional, 50 MHz PD
100 MHz Offset
-171
dBc/Hz
-53
dBc
193.7
fsec
1 kHz Offset
-112
dBc/Hz
Integer, 50 MHz PD
10 kHz Offse
-110
dBc/Hz
Integer, 50 MHz PD
100 kHz Offset
-111
dBc/Hz
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
Closed Loop Phase Noise PLL + VCO at fvco with 127 KHz BW Loop Filter Design[6]
Integer, 50 MHz PD
Integer, 50 MHz PD
1 MHz Offset
-138
dBc/Hz
Integer, 50 MHz PD
10 MHz Offset
-160
dBc/Hz
Integer, 50 MHz PD
100 MHz Offset
-171
dBc/Hz
Integrated Phase Noise
RMS Jitter
from 10KHz to 100MHz
-57.3
dBc
118
fsec
Fractional, 50 MHz PD
1 kHz Offset
-109
dBc/Hz
Fractional, 50 MHz PD
10 kHz Offse
-107
dBc/Hz
Fractional, 50 MHz PD
100 kHz Offset
-110
dBc/Hz
Fractional, 50 MHz PD
1 MHz Offset
-136
dBc/Hz
Fractional, 50 MHz PD
10 MHz Offset
-157
dBc/Hz
Fractional, 50 MHz PD
100 MHz Offset
-171
dBc/Hz
-55.55
dBc
144.1
fsec
Floor Integer Mode
-230
dBc/Hz
Floor Fractional Mode
-227
dBc/Hz
Integrated Phase Noise
RMS Jitter
Figure of Merit
7-5
-54.2
169.8
from 10KHz to 100MHz
Normalized 1 Hz
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Electrical Specifications (Continued)
Parameter
Condition
Min.
Typ.
-268
Flicker (Both Modes)
Max.
Units
dBc/Hz
[2] The closed loop phase noise PLL+VCO at fvco/2 can be calculated by subtracting 6dB. The closed loop phase noise PLL+VCO at 2fvco can be
calculated by adding 6dB.
Loop Filter Configuration Table
C1
(pF)
C2
(nF)
C3
(pF)
C4
(pF)
R2
(kΩ)
R3
(kΩ)
R4
(kΩ)
[3]
470
10
82
82
0.51
1
1
[4]
120
2.7
33
33
0.91
2
2
[5]
330
10
180
180
0.75
1
1
[6]
120
4.7
33
33
1.3
2
2
Loop Filter Design
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
7
PLLS WITH INTEGRATED VCO - SMT
Loop Filter
Configuration
7-6
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Typical Closed Loop Fractional Phase
Noise [1]
Closed Loop Integer Phase Noise
-100
-120
-140
-160
50MHz PFD 71KHz BW 169 fsec
50MHz PFD 127KHz BW 118 fsec
100MHz PFD 100KHz BW 129 fsec
100MHz PFD 178KHz BW 89 fsec
-180
3
10
10
4
7
10
5
10
6
10
7
10
-120
-140
-160
50MHz PFD 71KHz BW 193 fsec
50MHz PFD 127KHz BW 144 fsec
100MHz PFD 100KHz BW 123 fsec
100MHz PFD 178KHz BW 108 fsec
-180
3
10
8
OFFSET FREQUENCY (Hz)
4
10
5
10
6
10
7
10
8
Typical Tuning Curves vs. Switch Position
-20
1100
-40
fmax
-60
1336MHz
-80
2647MHz
5304MHz
n0
1050
n2
kvco (MHz/V)
PHASE NOISE (dBc/Hz)
10
OFFSET FREQUENCY (Hz)
Free Running Phase Noise
fmax
1000
-100
-120
950
-140
fmin
n4
n6
n8
n10
n12
n14
n16
n18
n20
n22
n24
n26
n28
n30 n31
-160
-180
2
10
900
10
3
10
4
10
5
10
6
10
7
10
0
1
2
8
3
4
5
TUNING VOLTAGE (V)
OFFSET FREQUENCY (Hz)
Free Running VCO Phase Noise
Over Temperature
Typical VCO Tuning Voltage After
Calibration
-100
5
TUNE VOLTAGE AFTER CALIBRATION (V)
-110
PHASE NOISE (dBc/Hz)
PLLS WITH INTEGRATED VCO - SMT
PHASE NOISE (dBc/Hz) @2607MHz
PHASE NOISE (dBc/Hz) @2600MHz
-100
100 kHz Offset
+27C
+85C
-40C
-120
-130
1 MHz Offset
-140
-150
10 MHz Offset
-160
-170
2620
2660
2700
2740
2780
2820
FREQUENCY (MHz)
4
fmin
3
31
fmax
15
0
2
1
0
VCO FREQUENCY
[1] RMS Jitter data is measured from 10KHz to 100MHz bandwidth.
7-7
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Typical VCO Sensitivity vs. Cap @
Fo Voltage
Typical Output Power - Narrow Band
Match
20
35
TUNING CAP 31, 2539 MHz AT 2V
TUNING CAP 15, 2644 MHz AT 2V
TUNING CAP 0, 2898 MHz AT 2V
15
OUTPUT POWER (dBm)
KVCO (MHz/V)
30
25
20
Typical Operating Range
15
10
10
5
Divide-by-2
Fundamental
-40C
-40C
27C
27C
85C
85C
Doubler
-40C
0
27C
-5
5
0
0
1
2
3
4
-10
1000
5
TUNING VOLTAGE (V)
85C
2000
3000
4000
5000
6000
OUTPUT FREQUENCY (MHz)
Figure of Merit
NORMALIZED PHASE NOISE (dBc/Hz)
-200
-210
Typ FOM vs Offset
-220
FOM Floor
FOM 1/f Noise
-230
-240
2
10
10
3
10
4
10
5
10
6
FREQUENCY OFFSET (Hz)
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
7
PLLS WITH INTEGRATED VCO - SMT
40
7-8
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Pin Descriptions
PLLS WITH INTEGRATED VCO - SMT
7
7-9
Pin Number
Function
Description
1
AVDD
DC Power Supply for analog circuitry.
2, 5, 6, 8, 9,
11 - 14, 18 - 22, 24,
26, 34, 37, 38
N/C
The pins are not connected internally; however, all data shown herein
was measured with these pins connected to RF/DC ground externally.
3
VPPCP
Power Supply for charge pump analog section
4
CP
Charge Pump Output
7
VDDCP
Power Supply for the charge pump digital section
10
RVDD
Reference Supply
15
XREFP
Reference Oscillator Input
16
DVDD3V
DC Power Supply for Digital (CMOS) Circuitry
17
CEN
Chip Enable. Connect to logic high for normal operation.
23
VTUNE
VCO Varactor. Tuning Port Input.
25
VCC2
VCO Analog Supply 2
27
VCC1
VCO Analog Supply 1
28
RF_N [1]
RF Positive Output
29
[1]
30
RF_P
SEN
RF Negative Output
PLL Serial Port Enable (CMOS) Logic Input
31
SDI
PLL Serial Port Data (CMOS) Logic Input
32
SCK
PLL Serial Port Clock (CMOS) Logic Input
33
LD_SDO
Lock Detect, or Serial Data, or General Purpose (CMOS) Logic Output (GPO)
35
VCCHF
DC Power Supply for Analog Circuitry
36
VCCPS
DC Power Supply for Analog Prescaler
39
VCCPD
DC Power Supply for Phase Detector
40
BIAS
External bypass decoupling for precision bias circuits.
Note: 1.920V ±20mV reference voltage (BIAS) is generated internally and cannot
drive an external load. Must be measured with 10GΩ meter such as Agilent 34410A,
normal 10MΩ DVM will read erroneously.
[1] For doubler mode of operation, pin 28 (RF_N) and pin 29 (RF_P) outputs must be shorted together.
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Absolute Maximum Ratings
AVDD, RVDD, DVDD3V, VCCPD,
VCCHF, VCCPS
-0.3V to +3.6V
VPPCP, VDDCP, VCC1
-0.3V to +5.8V
VCC2
-0.3V to +5.5V
Operating Temperature
-40°C to +85°C
Storage Temperature
-65°C to 125°C
Maximum Junction Temperature
125 °C
Thermal Resistance (RTH)
(junction to ground paddle)
20 °C/W
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device.
This is a stress rating only; functional operation of the
device at these or any other conditions above those
indicated in the operational section of this specification
is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Reflow Soldering
Peak Temperature
260°C
Time at Peak Temperature
40 sec
ESD Sensitivity (HBM)
7
Class 1B
PLLS WITH INTEGRATED VCO - SMT
Outline Drawing
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR
HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
Package Marking [1]
HMC840LP6CE
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
H840
XXXX
[1] 4-Digit lot number XXXX
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
7 - 10
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Evaluation PCB
PLLS WITH INTEGRATED VCO - SMT
7
The circuit board used in the application should use RF circuit design techniques. Signal lines should have
50 Ohm impedance while the package ground leads and exposed paddle should be connected directly
to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the
top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
Evaluation PCB Schematic
To view this Evaluation PCB Schematic please visit www.hittite.com and choose HMC840LP6CE from the
“Search by Part Number” pull down menu to view the product splash page.
Evaluation Order Information
Item
Evaluation PCB Only
Evaluation Kit
7 - 11
Contents
Part Number
HMC840LP6CE Fo/2 & Fo Evaluation PCB
129515-HMC840LP6CE
HMC840LP6CE 2xFo Evaluation PCB
129516-HMC840LP6CE
HMC840LP6CE Fo/2 & Fo Evaluation PCB
USB Interface Board
6’ USB A Male to USB B Female Cable
CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software,
Hittite PLL Design Software)
129075-HMC840LP6CE
HMC840LP6CE 2xFo Evaluation PCB
USB Interface Board
6’ USB A Male to USB B Female Cable
CD ROM (Contains User Manual, Evaluation PCB Schematic, Evaluation Software,
Hittite PLL Design Software)
129076-HMC840LP6CE
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
HMC840LP6CE
v00.1210
FRACTIONAL-N PLL WITH INTEGRATED VCO
1310 - 1415, 2620 - 2830, 5240 - 5660 MHz
Notes:
PLLS WITH INTEGRATED VCO - SMT
7
For price, delivery, and to place orders: Hittite Microwave Corporation,20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343
Fax: 978-250-3373
Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or [email protected]
7 - 12