Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 N 153 Features –– Infrared interface for format alignment by power tool –– Absolute multiturn measuring system –– Display: LCD backlit, two lines –– Actual value and target display –– LED status display –– Interface RS485 –– Resolution: 1440 steps/revolution ±4096 revolutions –– Two operating keys for format alignment touch by touch Technical data - mechanical design Voltage supply 24 VDC ±10 % Hollow shaft ø14 mm Current consumption ≤40 mA Operating speed ≤600 rpm (short-term) Display LCD, 7-segment display, 2-lines, backlit Protection DIN EN 60529 IP 65 Measuring principle Absolute multiturn measuring system Operating temperature -10...+50 °C Storing temperature -20...+70 °C Measuring range -99.99...+999.99 mm -9.999...+99.999 inch Relative humidity 80 % non-condensing Torque support Torque pin provided at housing Steps per turn 1440 E-connection Number of turns 4096 / 12 bit Spindle pitch ≤14 mm Interface RS485 (ASCII protocol) - Male/female connector M8, 4-pin - Cable output (30/15 cm) with male/female connector M8, 4-pin Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Operation / keypad Membrane with two keys Housing type Surface-mount with hollow shaft Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Counting direction Spindle pitch Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Dimensions W x H x L 37 x 75 x 45 mm Mounting Surface-mount with hollow shaft Weight approx. 120 g Material Polyamide black, UL 94V-0 Motive positioning Two softkeys for format alignment Connected to power tool by infrared interface Standard DIN EN 61010‑1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL/cUL 1 www.baumerivo.com 30/10/2008 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. N 153 with cable output Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 N 153 Part number 1 3 A A multicon AccuDrive is an economical system for mobile, motive format alignment. By AccuDrive positioning of shafts to the desired format is quick, accurate and less fussy hand crank operations. Saving setup times and avoiding editing errors are consequently the most convincing arguments. The electrically commutated professional power tool ASMIR serves as mobile actuator that communicates with N 153 spindle position displays by infrared interface. Red and green status LEDs provided at the position display indicate the operator which shafts require alignment. A flashing LED indicates the positioning order. The power tool is a vital help in aligning the respective shafts to the new format. Select the desired positioning direction by aid of the two pushbuttons provided at the power tool. Press and hold the start button to start the positioning operation at slow speed with increasing acceleration. This way, the operator is able to proceed the positioning operation in direct sight with an accuracy of ±1/100 mm. Any shaft positions once effected can be filed under a parameter profile in the control to be recalled any time. By serial interface maximum 32 spindle position displays may be networked to PC or PLC. Through solutions are realized by memory controller N 242 as memory and operating terminal where max. 100 format profiles can be entered and saved by Teach-in. 01 Hollow shaft A Hollow shaft ø14 mm Display A Inclined Voltage supply 3 24 VDC E-connection 0 Connector output M8 1 Cable output M8 Interface 1 RS485 Accessories Z 178.A01 Adaptor cable between cable connector M8 and female M16, 1 m Z 178.AW1 Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Z 178.B01 Mating connector M8, 4-pin, less cable Z 178.D05 Data and supply cable M8, Master to N 150 and N 155, 5 m Z 178.S01 Cable connector M8, 4-pin, less cable Z 178.V01 Coupling cable 1 m between M8 and M8 Subject to modification in technic and design. Errors and omissions excepted. Connectors and cables (page %S) 2 www.baumerivo.com 30/10/2008 N 153. Description Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 N 153 Terminal assignment SPA – connector and female connector, 4-pin Connector Assignment Pin 1 Tx/Rx-, RS485 Pin 2 Tx/Rx+, RS485 Pin 3 Sensor supply +24 V Pin 4 Sensor supply 0 V M8 connector 1 3 M8 female connector 2 2 4 4 1 3 Dimensions Connect or output 4.8 Torque pin 6 ° ø14H7 300 A Seal 14 A 1 13 52 12.5 M8 connector Connector Female connector 3 ø12 ø12 www.baumerivo.com Subject to modification in technic and design. Errors and omissions excepted. 45 M8 female connector 30/10/2008 6.5 31.8 30.15 10 ø6h9 28 2:1 60 16 Pin M4 13 26 37 StatusLED IR-Diode ø20 22 20.5 75 0.5x 45° Cable output 150 75 Spindle Position Displays Hollow shaft max. ø14 mm, with infrared interface Format alignment by power tool, interface RS485 4 www.baumerivo.com 30/10/2008 Subject to modification in technic and design. Errors and omissions excepted. N 153