TI TPA2038D1

TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
3.2 W Mono Class-D Audio Power Amplifier With
Selectable Gain and Auto-Recovering Short-Circuit Protection
Check for Samples: TPA2038D1
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
1
•
•
•
•
•
•
Filter-Free Mono Class-D Speaker Amp
GAIN Pin Selects Between 6 dB and 12 dB
3.2 W into 4 Ω from 5 V supply at 10% THD+N
Powerful Mono Class-D Speaker Amplifier
– 1% at 1.4 W into 8 Ω from 5 V Supply
– 1% at 2.5 W into 4 Ω from 5 V Supply
Integrated Image Reject Filter for DAC Noise
Reduction
Low Output Noise of 20 μV
Low Quiescent Current of 1.5 mA
Auto-Recovering Short-Circuit Protection
Thermal-Overload Protection
9-Ball 1,21 mm × 1,16 mm 0,4 mm Pitch WCSP
Wireless or Cellular Handsets and PDAs
Portable Navigation Devices
General Portable Audio Devices
DESCRIPTION
The TPA2038D1 is a 3.2 W into 8-ohm (10% THD)
high efficiency filter-free class-D audio power
amplifier. The GAIN pin sets gain to either 6 dB or
12 dB.
Features like 95% efficiency, 1.5 mA quiescent
current, 0.5 μA shutdown current, 81 dB PSRR,
20 μV output noise, and improved RF immunity make
the TPA2038D1 class-D amplifier ideal for cellular
handsets. A start-up time is within 4 ms with no
turn-on pop.
The TPA2038D1 is available in a 1.21 mm x
1.16 mm, 0.4 mm pitch wafer chip scale package
(WCSP).
APPLICATION CIRCUIT
GAIN
VDD
Gain Select
IN+
VO+
–
PWM
To battery
Cs
Internal
Oscillator
H-Bridge
VO+
TPA2038D1
9-BALL 0.4mm PITCH
WAFER CHIP SCALE PACKAGE (YFF)
(TOP VIEW OF PCB)
IN+
GAIN
VO-
A1
A2
A3
VDD
PVDD
PGND
B1
B2
B3
IN-
EN
VO+
C1
C2
C3
EN
Bias
Circuitry
GND
1.160 mm
IN-
TPA 2038 D1
1.214 mm
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
PACKAGED DEVICES (1)
TA
-40°C to 85°C
(1)
(2)
PART NUMBER (2)
SYMBOL
TPA2038D1YFFR
QWK
TPA2038D1YFFT
QWK
9-ball WCSP
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com
The YFF package is only available taped and reeled. The suffix "R" indicates a reel of 3000, the suffix "T" indicates a reel of 250.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range, TA = 25°C (unless otherwise noted) (1)
VALUE
UNIT
In active mode
–0.3 to 6.0
V
In shutdown mode
–0.3 to 6.0
V
–0.3 to VDD + 0.3
V
3.2
Ω
VDD, PVDD
Supply voltage
VI
Input voltage
RL
Minimum load resistance
EN, IN+, IN–
Output continuous total power dissipation
See Dissipation Rating Table
TA
Operating free-air temperature range
–40 to 85
°C
TJ
Operating junction temperature range
–40 to 150
°C
Tstg
Storage temperature range
–65 to 85
°C
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to Absolute Maximum Ratings conditions for extended periods may affect device reliability.
DISSIPATION RATINGS
(1)
PACKAGE
DERATING FACTOR (1)
TA < 25°C
TA = 70°C
TA = 85°C
YFF (WCSP)
4.2 mW/°C
525 mW
336 mW
273 mW
Derating factor measure with high K board.
RECOMMENDED OPERATING CONDITIONS
VDD,
PVDD
Class-D supply voltage
VIH
High-level input voltage
EN, GAIN
VIL
Low-level input voltage
EN, GAIN
VIC
Common mode input voltage range
VDD = 2.5 V, 5.5 V, CMRR ≥ 49 dB
TA
Operating free-air temperature
MIN
MAX
2.5
5.5
1.3
UNIT
V
V
0.35
V
0.75
VDD-1.1
V
–40
85
°C
GAIN SETTING
2
GAIN PIN
GAIN SETTING
GND
12 dB
VDD
6 dB
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
ELECTRICAL CHARACTERISTICS
PVDD = VDD = 3.6 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
|VOS|
Output offset voltage
(measured differentially)
VDD = 2.5 V to 5.5 V, GAIN = VDD
|IIH|
High-level EN input current
VDD = 5.5 V, EN = GAIN = 5.5 V
|IIL|
Low-level EN input current
VDD = 5.5 V, EN = GAIN = 0 V
I(Q)
Quiescent current
MIN
TYP
MAX
1
5
mV
50
μA
1
μA
VDD = 5.5 V, no load
1.8
2.5
VDD = 3.6 V, no load
1.5
2.3
VDD = 2.5 V, no load
1.3
2.1
0.1
2
I(SD)
Shutdown current
EN = 0.35 V, VDD = 3.6 V
RO,
Output impedance in
shutdown mode
EN = 0.35 V
f(SW)
Switching frequency
VDD = 2.5 V to 5.5 V
250
300
350
AV
Gain
GAIN = 0 V
11.5
12
12.5
GAIN = VDD
5.5
6
6.5
SD
REN
Resistance from EN to GND
RIN
Single-ended input resistance
2
150
AV = 12 dB; EN = VDD
75
EN = 0.35 V
75
mA
μA
kΩ
300
AV = 6 dB; EN = VDD
UNIT
kHz
dB
kΩ
kΩ
OPERATING CHARACTERISTICS
PVDD = VDD = 3.6 V, AV = 6 dB, TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
THD + N = 10%, f = 1 kHz,
RL = 4 Ω
THD + N = 1%, f = 1 kHz,
RL = 4 Ω
PO
Output power
THD + N = 10%, f = 1 kHz,
RL = 8 Ω
THD + N = 1%, f = 1 kHz,
RL = 8 Ω
Output voltage noise, AV = 6 dB
EN
Output voltage noise, AV = 12 dB
THD+N
PSRR
Total harmonic distortion plus noise
AC power supply rejection ratio
Copyright © 2011, Texas Instruments Incorporated
VDD = 3.6 V, Inputs AC
grounded with CI = 2 μF,
f = 20 Hz to 20 kHz
MIN
TYP
VDD = 5 V
3.24
VDD = 3.6 V
1.62
VDD = 2.5 V
0.70
VDD = 5 V
2.57
VDD = 3.6 V
1.32
VDD = 2.5 V
0.57
VDD = 5 V
1.80
VDD = 3.6 V
0.91
VDD = 2.5 V
0.42
VDD = 5 V
1.46
VDD = 3.6 V
0.74
VDD = 2.5 V
0.33
A-weighting
20
No weighting
26
A-weighting
27
No weighting
36
VDD = 5.0 V, PO = 1.0 W, f = 1 kHz, RL = 8 Ω
0.12%
VDD = 3.6 V, PO = 0.5 W, f = 1 kHz, RL = 8 Ω
0.05%
VDD = 2.5 V, PO = 0.2 W, f = 1 kHz, RL = 8 Ω
0.05%
VDD = 5.0 V, PO = 2.0 W, f = 1 kHz, RL = 4 Ω
0.32%
VDD = 3.6 V, PO = 1.0 W, f = 1 kHz, RL = 4 Ω
0.11%
VDD = 2.5 V, PO = 0.4 W, f = 1 kHz, RL = 4 Ω
0.12%
AV = 6 dB, Inputs AC grounded with CI = 2 μF,
200 mVpp ripple, f = 217 Hz
81
AV = 12 dB, Inputs AC grounded with
CI = 2 μF, 200 mVpp ripple, f = 217 Hz
82
MAX
UNIT
W
W
W
W
μVRMS
dB
3
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
OPERATING CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, AV = 6 dB, TA = 25°C, RL = 8 Ω (unless otherwise noted)
PARAMETER
CMRR
TEST CONDITIONS
Common mode rejection ratio
TSU
MIN
TYP
AV = 6 dB, VIC = 200 mVPP, f = 217 Hz
79
AV = 12 dB, VIC = 200 mVPP, f = 217 Hz
77
Startup time from shutdown
MAX
UNIT
dB
4
ms
2
A
VO+ shorted to VDD
VO– shorted to VDD
ISC
Short circuit protection threshold
VO+ shorted to GND
VO– shorted to GND
VO+ shorted to VO–
TAR
Overcurrent recovery time
VDD = 2.5 V to 5.5 V
100
ms
Terminal Functions
TERMINAL
NAME
WCSP BALL
I/O
DESCRIPTION
IN+
A1
I
Positive audio input.
GAIN
A2
I
Gain select. Set to GND for 12 dB; set to VDD for 6 dB.
VO-
A3
O
Negative audio output.
VDD
B1
I
Power supply terminal. Connect to PVDD using a direct connection.
PVDD
B2
I
Class-D output power supply. Connect to VDD using a direct connection.
GND
B3
I
Ground.
IN–
C1
I
Negative audio input.
EN
C2
I
Enable. Set to logic high to enable device.
VO+
C3
O
Positive audio output.
FUNCTIONAL BLOCK DIAGRAM
GAIN
EN
A2
Gain
Select
SD
Input
Buffer
SC
300 KΩ
4
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TEST SETUP FOR GRAPHS
CI
+
Measurement
Output
OUT+
IN+
TPA2038D1
CI
-
IN-
OUTVDD
+
Load
30 kHz
Low Pass
Filter
Measurement
Input
-
GND
CS1
CS2
+
VDD
-
1. CI was shorted for any common-mode input voltage measurement. All other measurements were taken with CI = 0.1 μF
(unless otherwise noted).
2. CS1 = 0.1 μF is placed very close to the device. The optional CS2 = 10 μF is used for datasheet graphs.
3. The 30 kHz low-pass filter is required even if the analyzer has an internal low-pass filter. An RC low-pass filter (1 kΩ,
4700 pF) is used on each output for the data sheet graphs.
Copyright © 2011, Texas Instruments Incorporated
5
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
EFFICIENCY
vs OUTPUT POWER
100
100
90
90
80
80
70
70
60
50
40
RL = 8 Ω + 33 µH
Gain = 6 dB
30
20
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
60
50
40
RL = 4 Ω + 33 µH
Gain = 6 dB
30
20
VDD = 2.5 V
VDD = 3.3 V
VDD = 5.0 V
10
0
0.0
η − Efficiency − %
η − Efficiency − %
EFFICIENCY
vs OUTPUT POWER
VDD = 2.5 V
VDD = 3.3 V
VDD = 5.0 V
10
0
0.0
2.0
0.2
0.4
0.6
PO − Output Power − W
POWER DISSIPATION
vs OUTPUT POWER
0.6
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
VDD = 3.6 V
Gain = 6 dB
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
0.1
2.0
VDD = 5.0 V
Gain = 6 dB
0.3
0.2
0.1
0.4
0.8
1.2
1.6
0.0
0.0
2.0
0.4
0.8
1.2
1.6
2.0
2.4
2.8
3.2
3.6
4.0
PO − Output Power − W
Figure 3.
Figure 4.
SUPPLY CURRENT
vs OUTPUT POWER
SUPPLY CURRENT
vs OUTPUT POWER
600m
1
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
500m
IDD − Supply Current − A
IDD − Supply Current − A
1.8
0.4
PO − Output Power − W
700m
600m
500m
400m
300m
200m
RL = 4 Ω + 33 µH
Gain = 6 dB
100m
0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6
PO − Output Power − W
Figure 5.
6
1.6
0.5
0.2
800m
1.4
POWER DISSIPATION
vs OUTPUT POWER
0.3
900m
1.2
Figure 2.
0.4
0.0
0.0
1.0
Figure 1.
PD − Power Dissipation − W
PD − Power Dissipation − W
0.5
0.8
PO − Output Power − W
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
400m
300m
200m
100m
0
0.0
RL = 8 Ω + 33 µH
Gain = 6 dB
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
PO − Output Power − W
Figure 6.
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
SUPPLY CURRENT
vs SUPPLY VOLTAGE
SUPPLY CURRENT
vs EN VOLTAGE
2.00
200
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
1.75
IDD − Supply Current − nA
IDD − Supply Current − mA
RL = No Load
RL = 8 Ω + 33 µH
RL = 4 Ω + 33 µH
1.50
1.25
150
100
50
Gain = 6 dB
1.00
2.5
3.0
3.5
4.0
4.5
5.0
0
0.0
5.5
0.1
0.2
VDD − Supply Voltage − V
0.4
Figure 7.
Figure 8.
OUTPUT POWER
vs LOAD RESISTANCE
OUTPUT POWER
vs LOAD RESISTANCE
4
0.5
4
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
THD+N = 10 %
Frequency = 1 kHz
Gain = 6 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
THD+N = 1 %
Frequency = 1 kHz
Gain = 6 dB
3
PO − Output Power − W
PO − Output Power − W
0.3
VEN − EN Voltage − V
2
1
0
3
2
1
0
4
8
12
16
20
24
28
32
4
8
12
RL − Load Resistance − Ω
16
20
24
28
32
RL − Load Resistance − Ω
Figure 9.
Figure 10.
OUTPUT POWER
vs SUPPLY VOLTAGE
PO − Output Power − W
4
3
RL = 4 Ω, THD+N = 1 %
RL = 4 Ω, THD+N = 10 %
RL = 8 Ω, THD+N = 1 %
RL = 8 Ω, THD+N = 10 %
2
1
Frequency = 1 kHz
Gain = 6 dB
0
2.5
3.0
3.5
4.0
4.5
5.0
VDD − Supply Voltage − V
Figure 11.
Copyright © 2011, Texas Instruments Incorporated
7
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
100
THD + NOISE
vs OUTPUT POWER (6 dB GAIN)
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs OUTPUT POWER (6 dB GAIN)
RL = 4 Ω + 33 µH
Gain = 6 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
10
1
0.1
0.01
10m
100m
1
5
100
10
1
0.1
0.01
10m
100m
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs FREQUENCY (6 dB GAIN)
THD + NOISE
vs FREQUENCY (6 dB GAIN)
PO = 50 mW
PO = 250 mW
PO = 1 W
VDD = 5.0 V
RL = 8 Ω + 33 µH
Gain = 6 dB
1
0.1
0.01
0.001
100
1k
f − Frequency − Hz
10k
THD+N − Total Harmonic Distortion + Noise − %
Figure 13.
10
PO = 25 mW
PO = 125 mW
PO = 500 mW
VDD = 3.6 V
RL = 8 Ω + 33 µH
Gain = 6 dB
1
0.1
0.01
0.001
20k
20
100
1k
f − Frequency − Hz
10k
Figure 14.
Figure 15.
THD + NOISE
vs FREQUENCY (6 dB GAIN)
THD + NOISE
vs FREQUENCY (6 dB GAIN)
10
PO = 15 mW
PO = 75 mW
PO = 200 mW
VDD = 2.5 V
RL = 8 Ω + 33 µH
Gain = 6 dB
1
0.1
0.01
0.001
100
1k
f − Frequency − Hz
Figure 16.
8
5
Figure 12.
10
20
1
PO − Output Power − W
10k
20k
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
PO − Output Power − W
20
RL = 8 Ω + 33 µH
Gain = 6 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
20k
10
PO = 100 mW
PO = 500 mW
PO = 2 W
VDD = 5.0 V
RL = 4 Ω + 33 µH
Gain = 6 dB
1
0.1
0.01
0.001
20
100
1k
f − Frequency − Hz
10k
20k
Figure 17.
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
THD+N − Total Harmonic Distortion + Noise − %
10
PO = 50 mW
PO = 250 mW
PO = 1 W
VDD = 3.6 V
RL = 4 Ω + 33 µH
Gain = 6 dB
1
0.1
0.01
0.001
20
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs FREQUENCY (6 dB GAIN)
100
1k
f − Frequency − Hz
10k
10
1
0.1
0.01
0.001
20
100
10k
Figure 19.
THD + NOISE
vs OUTPUT POWER (12 dB GAIN)
THD + NOISE
vs OUTPUT POWER (12 dB GAIN)
RL = 4 Ω + 33 µH
Gain = 12 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
10
1
0.1
0.01
10m
100m
1
5
100
10
1
0.1
0.01
10m
100m
1
5
PO − Output Power − W
Figure 21.
THD + NOISE
vs FREQUENCY (12 dB GAIN)
THD + NOISE
vs FREQUENCY (12 dB GAIN)
10
PO = 50 mW
PO = 250 mW
PO = 1 W
1
0.1
0.01
0.001
100
1k
f − Frequency − Hz
Figure 22.
Copyright © 2011, Texas Instruments Incorporated
10k
20k
THD+N − Total Harmonic Distortion + Noise − %
Figure 20.
VDD = 5.0 V
RL = 8 Ω + 33 µH
Gain = 12 dB
20k
RL = 8 Ω + 33 µH
Gain = 12 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
PO − Output Power − W
THD+N − Total Harmonic Distortion + Noise − %
1k
f − Frequency − Hz
Figure 18.
100
20
PO = 30 mW
PO = 150 mW
PO = 400 mW
VDD = 2.5 V
RL = 4 Ω + 33 µH
Gain = 6 dB
20k
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs FREQUENCY (6 dB GAIN)
10
PO = 25 mW
PO = 125 mW
PO = 500 mW
VDD = 3.6 V
RL = 8 Ω + 33 µH
Gain = 12 dB
1
0.1
0.01
0.001
20
100
1k
f − Frequency − Hz
10k
20k
Figure 23.
9
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
1
0.1
0.01
0.001
1k
f − Frequency − Hz
10k
10
PO = 100 mW
PO = 500 mW
PO = 2 W
VDD = 5.0 V
RL = 4 Ω + 33 µH
Gain = 12 dB
1
0.1
0.01
0.001
20k
20
100
1k
f − Frequency − Hz
10k
Figure 24.
Figure 25.
THD + NOISE
vs FREQUENCY (12 dB GAIN)
THD + NOISE
vs FREQUENCY (12 dB GAIN)
10
PO = 50 mW
PO = 250 mW
PO = 1 W
VDD = 3.6 V
RL = 4 Ω + 33 µH
Gain = 12 dB
1
0.1
0.01
0.001
100
1k
f − Frequency − Hz
10k
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
100
20
PO = 15 mW
PO = 75 mW
PO = 200 mW
VDD = 2.5 V
RL = 4 Ω + 33 µH
Gain = 12 dB
1
0.1
0.01
0.001
20k
20
100
1k
f − Frequency − Hz
10k
Figure 27.
POWER SUPPLY REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE (12 dB GAIN)
POWER SUPPLY REJECTION RATIO
vs FREQUENCY (6 dB GAIN)
−10
−20
20k
0
RL = 8 Ω + 33 µH
Frequency = 217 Hz
Gain = 6 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.0
20k
10
Figure 26.
0
PSRR − Power Supply Rejection Ratio − dB
PO = 15 mW
PO = 75 mW
PO = 200 mW
VDD = 2.5 V
RL = 8 Ω + 33 µH
Gain = 12 dB
THD+N − Total Harmonic Distortion + Noise − %
10
20
Inputs AC−Grounded
CI = 2 µF
RL = 8 Ω + 33 µH
Gain = 6 dB
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VIC − Common Mode Input Voltage − V
Figure 28.
10
THD + NOISE
vs FREQUENCY (12 dB GAIN)
PSRR − Power Supply Rejection Ratio − dB
THD+N − Total Harmonic Distortion + Noise − %
THD + NOISE
vs FREQUENCY (12 dB GAIN)
4.5
5.0
20
100
1k
f − Frequency − Hz
10k
20k
Figure 29.
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
POWER SUPPLY REJECTION RATIO
vs FREQUENCY (6 dB GAIN)
POWER SUPPLY REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE
0
Inputs AC−Grounded
CI = 2 µF
RL = 4 Ω + 33 µH
Gain = 6 dB
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
PSRR − Power Supply Rejection Ratio − dB
PSRR − Power Supply Rejection Ratio − dB
0
−10
−100
20
100
1k
f − Frequency − Hz
10k
20k
RL = 8 Ω + 33 µH
Frequency = 217 Hz
Gain = 12 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VIC − Common Mode Input Voltage − V
Figure 30.
Figure 31.
POWER SUPPLY REJECTION RATIO
vs FREQUENCY (12 dB GAIN)
POWER SUPPLY REJECTION RATIO
vs FREQUENCY (12 dB GAIN)
0
Inputs AC−Grounded
CI = 2 µF
RL = 8 Ω + 33 µH
Gain = 12 dB
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
PSRR − Power Supply Rejection Ratio − dB
PSRR − Power Supply Rejection Ratio − dB
−20
−100
0.0
0
−100
Inputs AC−Grounded
CI = 2 µF
RL = 4 Ω + 33 µH
Gain = 12 dB
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
20
100
1k
f − Frequency − Hz
10k
20k
20
100
1k
f − Frequency − Hz
10k
Figure 32.
Figure 33.
COMMON MODE REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE (6 dB GAIN)
COMMON MODE REJECTION RATIO
vs FREQUENCY (6 dB GAIN)
0
−10
−20
RL = 8 Ω + 33 µH
Frequency = 217 Hz
Gain = 6 dB
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.0
CMRR − Common Mode Rejection Ratio − dB
CMRR − Common Mode Rejection Ratio − dB
−10
0
CI = 2 µF
RL = 8 Ω + 33 µH
Gain = 6 dB
−10
−20
20k
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VIC − Common Mode Input Voltage − V
Figure 34.
Copyright © 2011, Texas Instruments Incorporated
4.5
5.0
20
100
1k
f − Frequency − Hz
10k
20k
Figure 35.
11
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PVDD = VDD = 3.6 V, CI = 0.1 μF, CS1 = 0.1 μF, CS2 = 10 μF, TA = 25°C, RL = 8 Ω (unless otherwise noted)
COMMON MODE REJECTION RATIO
vs COMMON MODE INPUT VOLTAGE (12 dB GAIN)
RL = 8 Ω + 33 µH
Frequency = 217 Hz
Gain = 12 dB
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.0
0
CMRR − Common Mode Rejection Ratio − dB
CI = 2 µF
RL = 8 Ω + 33 µH
Gain = 12 dB
−10
−20
VDD = 2.5 V
VDD = 3.6 V
VDD = 5.0 V
−30
−40
−50
−60
−70
−80
−90
−100
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
20
5.0
100
1k
f − Frequency − Hz
VIC − Common Mode Input Voltage − V
10k
Figure 36.
Figure 37.
GSM POWER SUPPLY REJECTION
vs TIME (6 dB GAIN)
GSM POWER SUPPLY REJECTION
vs TIME (12 dB GAIN)
C1 - High
3.6 V
VDD
500 mV/div
C1 - Amplitude
500 mV
C1 - High
3.6 V
VDD
500 mV/div
C1 - Amplitude
500 mV
C1 - Duty Cycle
20%
VOUT
500 mV/div
20k
C1 - Duty Cycle
20%
VOUT
500 mV/div
0
2.5
5
7.5
10
12.5
15
17.5
20
22.5
25
0
2.5
5
7.5
t − Time − ms
10
12.5
15
17.5
20
22.5
25
t − Time − ms
G026
GSM POWER SUPPLY REJECTION
vs FREQUENCY (6 dB GAIN)
GSM POWER SUPPLY REJECTION
vs FREQUENCY (12 dB GAIN)
−50
−75
−100
VO − Output Voltage − dBV
−125
−25
−150
−50
−175
−75
−100
−125
−150
−175
−200
2.4
4.8
7.2
9.6
12
14.4
16.8
19.2
21.6
24
0
−25
−50
−75
−100
−125
VO − Output Voltage − dBV
−25
VDD − Supply Voltage − dBV
Figure 39.
0
0
G026
Figure 38.
−25
−150
−50
−175
−75
−100
−125
−150
−175
−200
0
f − Frequency − kHz
2.4
4.8
7.2
9.6
12
14.4
16.8
12
19.2
21.6
24
f − Frequency − kHz
G027
Figure 40.
VDD − Supply Voltage − dBV
CMRR − Common Mode Rejection Ratio − dB
0
−10
COMMON MODE REJECTION RATIO
vs FREQUENCY (12 dB GAIN)
G027
Figure 41.
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
APPLICATION INFORMATION
SHORT CIRCUIT AUTO-RECOVERY
When a short-circuit event occurs, the TPA2038D1 goes to shutdown mode and activates the integrated
auto-recovery process whose aim is to return the device to normal operation once the short-circuit is removed.
This process repeatedly examines (once every 100 ms) whether the short-circuit condition persists, and returns
the device to normal operation immediately after the short-circuit condition is removed. This feature helps protect
the device from large currents and maintain a good long-term reliability.
INTEGRATED IMAGE REJECT FILTER FOR DAC NOISE REJECTION
In applications which use a DAC to drive Class-D amplifiers, out-of-band noise energy present at the DAC's
image frequencies fold back into the audio-band at the output of the Class-D amplifier. An external low-pass filter
is often placed between the DAC and the Class-D amplifier in order to attenuate this noise.
The TPA2038D1 has an integrated Image Reject Filter with a low-pass cutoff frequency of 130 kHz, which
significantly attenuates this noise. Depending on the system noise specification, the integrated Image Reject
Filter may help eliminate external filtering, thereby saving board space and component cost.
COMPONENT SELECTION
Figure 42 shows the TPA2038D1 typical schematic with differential inputs, while Figure 43 shows the
TPA2038D1 with differential inputs and input capacitors. Figure 44 shows the TPA2038D1 with a single-ended
input.
Decoupling Capacitors (CS1, CS2)
The TPA2038D1 is a high-performance class-D audio amplifier that requires adequate power supply decoupling
to ensure the efficiency is high and total harmonic distortion (THD) is low. For higher frequency transients,
spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor CS1 = 0.1 μF,
placed as close as possible to the device VDD lead works best. Placing CS1 close to the TPA2038D1 is important
for the efficiency of the class-D amplifier, because any resistance or inductance in the trace between the device
and the capacitor can cause a loss in efficiency. For filtering lower-frequency noise signals, a 10 μF or greater
capacitor (CS2) placed near the audio power amplifier would also help, but it is not required in most applications
because of the high PSRR of this device. Typically, the smaller the capacitor's case size, the lower the
inductance and the closer it can be placed to the TPA2038D1. X5R and X7R dielectric capacitors are
recommended for both CS1 and CS2.
Input Capacitors (CI)
The TPA2038D1 does not require input coupling capacitors if the design uses a differential source that is biased
within the common-mode input voltage range. That voltage range is listed in the Recommended Operating
Conditions table. If the input signal is not biased within the recommended common-mode input range, such as in
needing to use the input as a high pass filter, shown in Figure 43, or if using a single-ended source, shown in
Figure 44, input coupling capacitors are required. The same value capacitors should be used on both IN+ and
IN– for best pop performance. The 3 dB high-pass cutoff frequency fC of the filter formed by the input coupling
capacitor CI and the input resistance RI (typically 150 kΩ) of the TPA2038D1 is given by Equation 1:
1
fC =
2πR
( ICI )
(1)
The value of the input capacitor is important to consider as it directly affects the bass (low frequency)
performance of the circuit. Speaker response may also be taken into consideration when setting the corner
frequency using input capacitors. Solving for the input coupling capacitance, we get:
1
CI =
(2πRIfC )
(2)
If the corner frequency is within the audio band, the capacitors should have a tolerance of ±10% or better,
because any mismatch in capacitance causes an impedance mismatch at the corner frequency and below.
Copyright © 2011, Texas Instruments Incorporated
13
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
For a flat low-frequency response, use large input coupling capacitors (0.1 μF or larger). X5R and X7R dielectric
capacitors are recommended.
To Battery
GAIN
Internal
Oscillator
Gain Select
VDD
CS
IN−
PWM
+
Differential
Input
H−
Bridge
VO−
VO+
_
IN+
GND
Bias
Circuitry
EN
TPA2038D1
Filter-Free Class D
Figure 42. Typical TPA2038D1 Application Schematic With DC-coupled Differential Input
GAIN
To Battery
Gain Select
CI
Internal
Oscillator
CS
IN−
PWM
+
Differential
Input
VDD
CI
H−
Bridge
VO−
VO+
_
IN+
GND
Bias
Circuitry
EN
TPA2038D1
Filter-Free Class D
Figure 43. TPA2038D1 Application Schematic With Differential Input and Input Capacitors
GAIN
Single-ended
Input
To Battery
Internal
Oscillator
Gain Select
VDD
IN−
+
CI
PWM
H−
Bridge
CS
VO−
VO+
_
IN+
CI
GND
EN
Bias
Circuitry
TPA2038D1
Filter-Free Class D
Figure 44. TPA2038D1 Application Schematic With Single-Ended Input
14
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
EFFICIENCY AND THERMAL INFORMATION
The maximum ambient operating temperature of the TPA2038D1 depends on the load resistance, power supply
voltage and heat-sinking ability of the PCB system. The derating factor for the YFF package is shown in the
dissipation rating table. Converting this to θJA:
1
q
+
JA
Derating Factor
(3)
Given θJA (from the Package Dissipation ratings table), the maximum allowable junction temperature (from the
Absolute Maximum ratings table), and the maximum internal dissipation (from Power Dissipation vs Output
Power figures) the maximum ambient temperature can be calculated with the following equation. Note that the
units on these figures are Watts RMS. Because audio contains crest factors (ratio of peak power to RMS power)
from 9–15 dB, thermal limitations are not usually encountered.
T Max + T Max * q P
A
J
JA Dmax
(4)
The TPA2038D1 is designed with thermal protection that turns the device off when the junction temperature
surpasses 150°C to prevent damage to the IC. Note that the use of speakers less resistive than 4 Ω (typ) is not
advisable. Below 4 Ω (typ) the thermal performance of the device dramatically reduces because of increased
output current and reduced amplifier efficiency. The Absolute Maximum rating of 3.2 Ω covers the manufacturing
tolerance of a 4 Ω speaker and speaker impedance decrease due to frequency. θJA is a gross approximation of
the complex thermal transfer mechanisms between the device and its ambient environment. If the θJA calculation
reveals a potential problem, a more accurate estimate should be made.
WHEN TO USE AN OUTPUT FILTER
Design the TPA2038D1 without an Inductor / Capacitor (LC) output filter if the traces from the amplifier to the
speaker are short. Wireless handsets and PDAs are great applications for this class-D amplifier to be used
without an output filter.
The TPA2038D1 does not require an LC output filter for short speaker connections (approximately 100 mm long
or less). A ferrite bead can often be used in the design if failing radiated emissions testing without an LC filter;
and, the frequency-sensitive circuit is greater than 1 MHz. If choosing a ferrite bead, choose one with high
impedance at high frequencies, but very low impedance at low frequencies. The selection must also take into
account the currents flowing through the ferrite bead. Ferrites can begin to loose effectiveness at much lower
than rated current values. See the EVM User's Guide (SLOU298) for components used successfully by TI.
Figure 45 shows a typical ferrite-bead output filter.
Ferrite
Chip Bead
VO−
1 nF
Ferrite
Chip Bead
VO+
1 nF
Figure 45. Typical Ferrite Chip Bead Filter
Copyright © 2011, Texas Instruments Incorporated
15
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
PRINTED CIRCUIT BOARD LAYOUT
In making the pad size for the WCSP balls, it is recommended that the layout use non-solder-mask-defined
(NSMD) land. With this method, the solder mask opening is made larger than the desired land area, and the
opening size is defined by the copper pad width. Figure 46 shows the appropriate diameters for a WCSP layout.
Figure 46. Land Pattern Image and Dimensions
SOLDER PAD
DEFINITIONS
COPPER PAD
SOLDER MASK
OPENING(5)
COPPER
THICKNESS
STENCIL OPENING(6) (7)
STENCIL
THICKNESS
Non-solder-maskdefined (NSMD)
0.23 mm
0.310 mm
1 oz max
(0.032 mm)
0.275 mm x 0.275 mm Sq.
(rounded corners)
0.1 mm thick
1. Circuit traces from NSMD defined PWB lands should be 75 μm to 100 μm wide in the exposed area inside
the solder mask opening. Wider trace widths reduce device stand off and impact reliability.
2. Best reliability results are achieved when the PWB laminate glass transition temperature is above the
operating the range of the intended application.
3. Recommend solder paste is Type 3 or Type 4.
4. For a PWB using a Ni/Au surface finish, the gold thickness should be less 0.5 mm to avoid a reduction in
thermal fatigue performance.
5. Solder mask thickness should be less than 20 μm on top of the copper circuit pattern
6. Best solder stencil performance is achieved using laser cut stencils with electro polishing. Use of chemically
etched stencils give inferior solder paste volume control.
7. Trace routing away from WCSP device should be balanced in X and Y directions to avoid unintentional
component movement due to solder wetting forces.
Figure 47. Layout Snapshot
An on-pad via is not required to route the middle ball B2 (PVDD) of the TPA2038D1. Short ball B2 (PVDD) to ball
B1 (VDD) and connect both to the supply trace as shown in Figure 47. This simplifies board routing and saves
manufacturing cost.
16
Copyright © 2011, Texas Instruments Incorporated
TPA2038D1
SLOS697 – AUGUST 2011
www.ti.com
PACKAGE DIMENSIONS
D
E
Max = 1244µm
Max = 1190µm
Min = 1184µm
Min = 1130µm
Copyright © 2011, Texas Instruments Incorporated
17
PACKAGE OPTION ADDENDUM
www.ti.com
6-Oct-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
TPA2038D1YFFR
ACTIVE
DSBGA
YFF
9
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPA2038D1YFFT
ACTIVE
DSBGA
YFF
9
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPA2038D1YFFT
Package Package Pins
Type Drawing
SPQ
DSBGA
250
YFF
9
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
180.0
8.4
Pack Materials-Page 1
1.34
B0
(mm)
K0
(mm)
P1
(mm)
1.34
0.81
4.0
W
Pin1
(mm) Quadrant
8.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPA2038D1YFFT
DSBGA
YFF
9
250
210.0
185.0
35.0
Pack Materials-Page 2
D: Max = 1.244 mm, Min =1.184 mm
E: Max = 1.19 mm, Min = 1.13 mm
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright © 1998, Texas Instruments Incorporated