TI SN54ABT5402

SCBS100B − JANUARY 1992 − REVISED JULY 1994
•
•
•
•
•
•
SN54ABT5402 . . . JT PACKAGE
SN74ABT5402 . . . DW PACKAGE
(TOP VIEW)
Output Ports Have 25-Ω Series Resistors,
So No External Resistors Are Required
State-of-the-Art EPIC-ΙΙB BiCMOS Design
Significantly Reduces Power Dissipation
Latch-Up Performance Exceeds 500 mA
Per JEDEC Standard JESD-17
Typical VOLP (Output Ground Bounce)
< 1 V at VCC = 5 V, TA = 25°C
Typical VOLV (Output Undershoot)
< 0.5 V at VCC = 5 V, TA = 25°C
Package Options Include Plastic
Small-Outline (DW) Packages, Ceramic
Chip Carriers (FK) and DIPs (JT)
Y1
Y2
Y3
Y4
Y5
Y6
GND
Y7
Y8
Y9
Y10
Y11
Y12
OE1
description
These 12-bit buffers and line drivers are designed
specifically to improve both the performance and
density of 3-state memory address drivers, clock
drivers, and bus-oriented receivers and
transmitters.
1
28
2
27
3
26
4
25
5
24
6
23
7
22
8
21
9
20
10
19
11
18
12
17
13
16
14
15
D1
D2
D3
D4
D5
D6
D7
VCC
D8
D9
D10
D11
D12
OE2
D4
D5
D6
D7
VCC
D8
D9
SN54ABT5402 . . . FK PACKAGE
(TOP VIEW)
The 3-state control gate is a 2-input AND gate with
active-low inputs so that if either output-enable
(OE1 or OE2) input is high, all 12 outputs are in the
high-impedance state.
4
D3
D2
D1
Y1
Y2
Y3
Y4
The outputs, which are designed to source or sink
up to 12 mA, include 25-Ω series resistors to
reduce overshoot and undershoot.
3 2 1 28 27 26
25
6
24
7
23
8
22
9
21
10
20
19
11
12 13 14 15 16 17 18
D10
D11
D12
OE2
OE1
Y12
Y11
Y5
Y6
GND
Y7
Y8
Y9
Y10
To ensure the high-impedance state during power
up or power down, OE should be tied to VCC
through a pullup resistor; the minimum value of the
resistor is determined by the current-sinking
capability of the driver.
5
The SN54ABT5402 is characterized for operation
over the full military temperature range of − 55°C
to 125°C. The SN74ABT5402 is characterized for
operation from −40°C to 85°C.
FUNCTION TABLE
INPUTS
D
OUTPUT
Y
OE1
OE2
L
L
L
L
L
L
H
H
H
X
X
Z
X
H
X
Z
EPIC-ΙΙB is a trademark of Texas Instruments Incorporated.
Copyright  1994, Texas Instruments Incorporated
!"# $%&'()* &%*+"*# ,
"*-%.(+"%* &'..)* +# %- /'01"&+"%* $+)2 .%$'&# &%*-%.( %
#/)&"-"&+"%*# /). !) ).(# %- )3+# *#.'()*# #+*$+.$ 4+..+*52
.%$'&"%* /.%&)##"*6 $%)# *% *)&)##+."15 "*&1'$) )#"*6 %- +11
/+.+()).#2
• DALLAS, TEXAS 75265
• HOUSTON, TEXAS 77251−1443
POST OFFICE BOX 655303
POST OFFICE BOX 1443
6−1
SCBS100B − JANUARY 1992 − REVISED JULY 1994
logic symbol†
14
OE1
OE2
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
logic diagram (positive logic)
OE1
&
28
27
OE2
EN
15
1
1
2
26
3
25
4
24
5
23
6
22
8
20
9
19
10
18
11
17
12
16
13
D1
14
15
28
1
Y1
Y1
Y2
Y3
To 11 Other Channels
Y4
Y5
Y6
Y7
Y8
Y9
Y10
Y11
Y12
† This symbol is in accordance with ANSI/IEEE Std 91-1984
and IEC Publication 617-12.
Pin numbers shown are for the DW and JT packages.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Voltage range applied to any output in the high state or power-off state, VO . . . . . . . . . . . . . −0.5 V to 5.5 V
Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −18 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Maximum power dissipation at TA = 55°C (in still air) (see Note 2): DW package . . . . . . . . . . . . . . . . . . . 1.2 W
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150°C and a board trace length of 750 mils.
For more information, refer to the Package Thermal Considerations application note in the 1994 ABT Advanced BiCMOS Technology
Data Book, literature number SCBD002B.
6−2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SCBS100B − JANUARY 1992 − REVISED JULY 1994
recommended operating conditions (see Note 3)
SN54ABT5402
VCC
VIH
Supply voltage
VIL
VI
Low-level input voltage
IOH
IOL
High-level output current
∆t /∆v
Input transition rise or fall rate
High-level input voltage
SN74ABT5402
MIN
MAX
MIN
MAX
4.5
5.5
4.5
5.5
2
2
0.8
Input voltage
0
Low-level output current
Outputs enabled
TA
Operating free-air temperature
NOTE 3: Unused or floating inputs must be held high or low.
−55
0
V
V
0.8
VCC
−12
UNIT
VCC
−12
V
V
mA
12
12
mA
10
10
ns / V
85
°C
125
−40
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
VOH
TEST CONDITIONS
VCC = 4.5 V,
VCC = 4.5 V,
II = −18 mA
IOH = −1 mA
VCC = 5 V,
VCC = 4.5 V
VOL
VCC = 4.5 V
II
IOZH
VCC = 5.5 V,
VCC = 5.5 V,
IOZL
Ioff
VCC = 5.5 V,
VCC = 0,
ICEX
IO
IOS‡
VCC = 5.5 V,
VCC = 5.5 V,
ICC
∆ICC§
Ci
Co
VCC = 5.5 V,
TA = 25°C
TYP†
MAX
SN54ABT5402
MIN
−1.2
MAX
SN74ABT5402
MIN
−1.2
MAX
−1.2
3.35
3.7
3.3
3.35
IOH = −1 mA
IOH = − 3 mA
3.85
4.2
3.8
3.85
3
3.1
IOH = −12 mA
IOL = 8 mA
2.6
VO = 2.7 V
VO = 0.5 V
VI or VO ≤ 4.5 V
VO = 5.5 V
Outputs high
0.65
±ā 1
±1
µA
50
50
50
µA
−50
−50
−50
µA
±100
µA
50
µA
−100
−25
−100
−25
−100
mA
−200
−50
−ā 200
−50
−200
mA
50
−45
−50
V
±1
±100
−25
V
V
0.8
VO = 2.5 V
VO = 0
UNIT
2.6
0.8
IOL = 12 mA
VI = VCC or GND
VCC = 5.5 V,
IO = 0,
VI = VCC or GND
VCC = 5.5 V,
One input at
3.4 V, Other
inputs at
VCC or GND
MIN
50
Outputs high
5
50
50
50
µA
Outputs low
36
45
45
45
mA
1
50
50
50
µA
Outputs enabled
1.5
1.5
1.5
Outputs disabled
0.05
0.05
0.05
1.5
1.5
1.5
Outputs disabled
Data inputs
Control inputs
VI = 2.5 V or 0.5 V
VO = 2.5 V or 0.5 V
mA
3
pF
8
pF
† All typical values are at VCC = 5 V.
‡ Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
§ This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND.
, "*-%.(+"%* &%*&).*# /.%$'&# "* !) -%.(+"7) %.
$)#"6* /!+#) %- $)7)1%/()*2 ,!+.+&)."#"& $++ +*$ %!).
#/)&"-"&+"%*# +.) $)#"6* 6%+1#2 )3+# *#.'()*# .)#).7)# !) ."6! %
&!+*6) %. $"#&%*"*') !)#) /.%$'&# 4"!%' *%"&)2
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
6−3
SCBS100B − JANUARY 1992 − REVISED JULY 1994
switching characteristics over recommended ranges of supply voltage and operating free-air
temperature, CL = 50 pF (unless otherwise noted) (see Figure 1)
FROM
(INPUT)
TO
(OUTPUT)
tPLH
tPHL
D
Y
tPZH
tPZL
OE
Y
tPHZ
tPLZ
OE
Y
PARAMETER
VCC = 5 V,
TA = 25°C
SN54ABT5402
MIN
TYP
MAX
MIN
MAX
MIN
MAX
2
4.5
5.7
2
6.7
2
6.5
1.5
3.7
4.5
1.5
5.5
1.5
5.2
2.5
5.7
6.6
2.5
8.6
2.5
8.5
2
4.4
5.5
2
6.9
2
6.8
1.5
3.6
4.4
1.5
5.5
1.5
5.2
1.5
4.2
5.4
1.5
7.4
1.5
6.9
, "*-%.(+"%* &%*&).*# /.%$'&# "* !) -%.(+"7) %.
$)#"6* /!+#) %- $)7)1%/()*2 ,!+.+&)."#"& $++ +*$ %!).
#/)&"-"&+"%*# +.) $)#"6* 6%+1#2 )3+# *#.'()*# .)#).7)# !) ."6! %
&!+*6) %. $"#&%*"*') !)#) /.%$'&# 4"!%' *%"&)2
6−4
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
SN74ABT5402
UNIT
ns
ns
ns
SCBS100B − JANUARY 1992 − REVISED JULY 1994
PARAMETER MEASUREMENT INFORMATION
7V
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
LOAD CIRCUIT FOR OUTPUTS
3V
Timing Input
1.5 V
0V
tw
tsu
3V
Input
1.5 V
th
3V
1.5 V
Data Input
1.5 V
1.5 V
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
Input
(see Note B)
1.5 V
0V
Output
1.5 V
VOL
tPLH
tPHL
Output
Waveform 2
S1 at Open
(see Note C)
VOH
Output
1.5 V
1.5 V
0V
tPLZ
Output
Waveform 1
S1 at 7 V
(see Note C)
VOH
1.5 V
1.5 V
tPZL
tPHL
tPLH
3V
Output
Control
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
1.5 V
tPZH
3.5 V
VOL + 0.3 V
VOL
tPHZ
1.5 V
VOH − 0.3 V
VOH
[0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
C. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
D. The outputs are measured one at a time with one transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
6−5
SCBS100B − JANUARY 1992 − REVISED JULY 1994
6−6
•
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443
•
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
SN74ABT5402DW
OBSOLETE
SOIC
DW
Pins Package Eco Plan (2)
Qty
28
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
SN74ABT5402DW
OBSOLETE
SOIC
DW
Pins Package Eco Plan (2)
Qty
28
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated