NUMONYX PF48F4000P0ZTQ0

®
Numonyx™ StrataFlash
(P30)
Embedded Memory
Datasheet
Product Features
„
High performance
„
— 85 ns initial access
— 52 MHz with zero wait states, 17ns clock-to-data output
synchronous-burst read mode
— 25 ns asynchronous-page read mode
— 4-, 8-, 16-, and continuous-word burst mode
— Buffered Enhanced Factory Programming (BEFP) at 5 μs/
byte (Typ)
— 1.8 V buffered programming at 7 μs/byte (Typ)
„
„
„
Quality and Reliability
— Operating temperature: –40 °C to +85 °C
— Minimum 100,000 erase cycles per block
— ETOX™ VIII process technology
Software
— 20 μs (Typ) program suspend
— 20 μs (Typ) erase suspend
— Numonyx™ Flash Data Integrator optimized
— Basic Command Set and Extended Command Set
compatible
— Common Flash Interface capable
Voltage and Power
— VCC (core) voltage: 1.7 V – 2.0 V
— VCCQ (I/O) voltage: 1.7 V – 3.6 V
— Standby current: 20μA (Typ) for 64-Mbit
— 4-Word synchronous read current:
13 mA (Typ) at 40 MHz
„
— One-Time Programmable Registers:
• 64 unique factory device identifier bits
• 2112 user-programmable OTP bits
— Selectable OTP Space in Main Array:
• Four pre-defined 128-KByte blocks (top or bottom
configuration)
• Up to Full Array OTP Lockout
— Absolute write protection: V PP = VSS
— Power-transition erase/program lockout
— Individual zero-latency block locking
— Individual block lock-down
Architecture
— Multi-Level Cell Technology: Highest Density at Lowest
Cost
— Asymmetrically-blocked architecture
— Four 32-KByte parameter blocks: top or bottom
configuration
— 128-KByte main blocks
Security
„
Density and Packaging
— 56- Lead TSOP package (64, 128, 256,
512- Mbit)
— 64- Ball Numonyx™ Easy BGA package (64,
128, 256, 512- Mbit)
— Numonyx™ QUAD+ SCSP (64, 128, 256,
512- Mbit)
— 16-bit wide data bus
Order Number: 306666-11
November 2007
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND
CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A
PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx
products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications.
Legal L ines and D isc laim er s
Numonyx B.V. may make changes to specifications and product descriptions at any time, without notice.
Numonyx B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented
subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or
otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves these for
future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting
Numonyx's website at http://www.numonyx.com.
Numonyx, the Numonyx logo, and StrataFlash are trademarks or registered trademarks of Numonyx B.V. or its subsidiaries in other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2007, Numonyx, B.V., All Rights Reserved.
Datasheet
2
November 2007
Order Number: 306666-11
P30
Contents
1.0
Introduction .............................................................................................................. 6
1.1
Nomenclature ..................................................................................................... 6
1.2
Acronyms........................................................................................................... 6
1.3
Conventions ....................................................................................................... 7
2.0
Functional Overview .................................................................................................. 8
2.1
Virtual Chip Enable Description.............................................................................. 8
3.0
Package Information ............................................................................................... 10
3.1
56-Lead TSOP................................................................................................... 10
3.2
64-Ball Easy BGA Package .................................................................................. 11
3.3
QUAD+ SCSP Packages ...................................................................................... 13
4.0
Ballout and Signal Descriptions ............................................................................... 16
4.1
Signal Ballout ................................................................................................... 16
4.2
Signal Descriptions ............................................................................................ 19
4.3
Dual-Die Configurations ..................................................................................... 21
4.4
Memory Maps ................................................................................................... 22
5.0
Maximum Ratings and Operating Conditions............................................................ 25
5.1
Absolute Maximum Ratings................................................................................. 25
5.2
Operating Conditions ......................................................................................... 25
6.0
Electrical Specifications ........................................................................................... 26
6.1
DC Current Characteristics.................................................................................. 26
6.2
DC Voltage Characteristics.................................................................................. 27
7.0
AC Characteristics ................................................................................................... 28
7.1
AC Test Conditions ............................................................................................ 28
7.2
Capacitance...................................................................................................... 29
7.3
AC Read Specifications....................................................................................... 29
7.4
AC Write Specifications ...................................................................................... 36
7.5
Program and Erase Characteristics....................................................................... 39
8.0
Power and Reset Specifications ............................................................................... 41
8.1
Power-Up and Power-Down................................................................................. 41
8.2
Reset Specifications........................................................................................... 41
8.3
Power Supply Decoupling ................................................................................... 42
9.0
Device Operations ................................................................................................... 43
9.1
Bus Operations ................................................................................................. 43
9.1.1 Reads ................................................................................................... 43
9.1.2 Writes................................................................................................... 44
9.1.3 Output Disable ....................................................................................... 44
9.1.4 Standby ................................................................................................ 44
9.1.5 Reset.................................................................................................... 44
9.2
Device Commands............................................................................................. 45
9.3
Command Definitions......................................................................................... 46
10.0 Read
10.1
10.2
10.3
Operations ...................................................................................................... 48
Asynchronous Page-Mode Read ........................................................................... 48
Synchronous Burst-Mode Read............................................................................ 48
Read Configuration Register................................................................................ 49
10.3.1 Read Mode ............................................................................................ 50
10.3.2 Latency Count........................................................................................ 50
November 2007
Order Number: 306666-11
Datasheet
3
P30
10.3.3 WAIT Polarity .........................................................................................52
10.3.4 Data Hold ..............................................................................................53
10.3.5 WAIT Delay............................................................................................53
10.3.6 Burst Sequence ......................................................................................54
10.3.7 Clock Edge.............................................................................................54
10.3.8 Burst Wrap ............................................................................................55
10.3.9 Burst Length ..........................................................................................55
10.3.10 End of Word Line (EOWL) Considerations ...................................................55
11.0 Programming Operations .........................................................................................56
11.1 Word Programming ............................................................................................56
11.1.1 Factory Word Programming......................................................................57
11.2 Buffered Programming .......................................................................................57
11.3 Buffered Enhanced Factory Programming ..............................................................58
11.3.1 BEFP Requirements and Considerations .....................................................58
11.3.2 BEFP Setup Phase ...................................................................................59
11.3.3 BEFP Program/Verify Phase ......................................................................59
11.3.4 BEFP Exit Phase......................................................................................60
11.4 Program Suspend ..............................................................................................60
11.5 Program Resume ...............................................................................................60
11.6 Program Protection ............................................................................................61
12.0 Erase Operations......................................................................................................62
12.1 Block Erase .......................................................................................................62
12.2 Erase Suspend ..................................................................................................62
12.3 Erase Resume ...................................................................................................63
12.4 Erase Protection ................................................................................................63
13.0 Security Modes ........................................................................................................64
13.1 Block Locking ....................................................................................................64
13.1.1 Lock Block .............................................................................................64
13.1.2 Unlock Block ..........................................................................................64
13.1.3 Lock-Down Block ....................................................................................64
13.1.4 Block Lock Status ...................................................................................65
13.1.5 Block Locking During Suspend ..................................................................65
13.2 Selectable One-Time Programmable Blocks ...........................................................66
13.3 Protection Registers ...........................................................................................66
13.3.1 Reading the Protection Registers...............................................................67
13.3.2 Programming the Protection Registers .......................................................68
13.3.3 Locking the Protection Registers ...............................................................68
14.0 Special Read States..................................................................................................69
14.1 Read Status Register..........................................................................................69
14.1.1 Clear Status Register ..............................................................................70
14.2 Read Device Identifier ........................................................................................70
14.3 CFI Query .........................................................................................................71
A
Write State Machine.................................................................................................72
B
Flowcharts ...............................................................................................................79
C
Common Flash Interface ..........................................................................................87
D
Additional Information.............................................................................................97
E
Ordering Information for Discrete Products .............................................................98
F
Ordering Information for SCSP Products ..................................................................99
Datasheet
4
November 2007
Order Number: 306666-11
P30
Revision History
Revision Date
Revision
April 2005
-001
Description
Initial Release
Revised discrete memory maps in Section 4.4, “Memory Maps” on page 22
Added memory maps for 512-Mbit top parameter devices in Section 4.4, “Memory
Maps” on page 22
August 2005
-002
Fixed size of Programming Region for 256-Mbit to be 8-Mbit in Section 4.4, “Memory
Maps” on page 22 and Section 11.0, “Programming Operations” on page 56
Removed power supply sequencing requirement in Section 8.1, “Power-Up and PowerDown” on page 41
Updated conditions for Table 15, “Capacitance” on page 29
Updated CFI table in Appendix C, “Common Flash Interface”
Added note to Table 34, “Device ID codes” on page 71 for stacked Device ID codes
Synchronous burst read operation is currently not supported for the TSOP package
Updated 512-Mbit Easy BGA Ball Height (symbol A1) in Figure 2, “Easy BGA Mechanical
September 2005
-003
November 2005
-004
Updated read access speed for 265M TSOP package
February 2006
-005
Removed all references to 1 Gigabit.
Specifications” on page 11
April 2006
-006
•
•
•
•
•
•
•
•
Added 52 MHz capabilities,
Added TSOP Package information for 512 Mb throughout the document,
Added Section 2.1, “Virtual Chip Enable Description” on page 8,
Modified figures in Section 4.3, “Dual-Die Configurations” on page 21,
Modified Table 9, “512-Mbit Top and Bottom Parameter Memory Map (Easy BGA and
QUAD+ SCSP)” on page 23,
Modified Notes 5 & 6 to Reset Specifications table in Section 8.2, “Reset
Specifications” on page 41,
Added additional note on 512 Mb capability in Table 31, “Selectable OTP Block
Mapping” on page 66.
Updated the following tables to 52 MHz: Table 16, “AC Read Specifications for 64/
128- Mbit Densities” on page 29 and Table 17, “AC Read Specifications for 256/512-Mbit
Densities” on page 30.
May 2006
-007
May-2006
-008
•
Added notes 1, 2, and 3 to Table 15, “Capacitance” on page 29.
June - 2007
-009
•
•
•
•
•
•
Correct typos and add clarifications
Enabled specific burst operation on TSOP packages.
Updated device commands table.
Updaed description on synchronous burst operation.
Added EOWL description.
Updated flowcharts
November 2007
-010
•
•
Updated for 65nm lithography
Added W602 - Erase to Suspend
November 2007
11
•
Applied Numonyx branding.
November 2007
Order Number: 306666-11
Datasheet
5
P30
1.0
Introduction
This document provides information about the Numonyx™ StrataFlash® Embedded
Memory (P30) product and describes its features, operation, and specifications.
The Numonyx™ StrataFlash® Embedded Memory (P30) product is the latest generation
of Numonyx™ StrataFlash® memory devices. Offered in 64-Mbit up through 512-Mbit
densities, the P30 device brings reliable, two-bit-per-cell storage technology to the
embedded flash market segment. Benefits include more density in less space, highspeed interface, lowest cost-per-bit NOR device, and support for code and data
storage. Features include high-performance synchronous-burst read mode, fast
asynchronous access times, low power, flexible security options, and three industry
standard package choices. The P30 product family is manufactured using Intel* 130 nm
ETOX™ VIII process technology.
The P30 product family is also planned on the Intel* 65nm process lithography. 65nm
AC timing changes are noted in this datasheet, and should be taken into account for all
new designs.
1.1
Nomenclature
1.8 V:
VCC (core) voltage range of 1.7 V – 2.0 V
3.0 V:
VCCQ (I/O) voltage range of 1.7 V – 3.6 V
9.0 V:
VPP voltage range of 8.5 V – 9.5 V
Block:
A group of bits, bytes, or words within the flash memory array that erase simultaneously
when the Erase command is issued to the device. The P30 has two block sizes: 32-KByte
and 128-KByte.
Main block:
An array block that is usually used to store code and/or data. Main blocks are larger than
parameter blocks.
Parameter block:
An array block that is usually used to store frequently changing data or small system
parameters that traditionally would be stored in EEPROM.
Top parameter device:
A device with its parameter blocks located at the highest physical address of its memory
map.
Bottom parameter device:
A device with its parameter blocks located at the lowest physical address of its memory
map.
1.2
Acronyms
BEFP:
Buffer Enhanced Factory Programming
CUI:
Command User Interface
MLC:
Multi-Level Cell
OTP:
One-Time Programmable
PLR:
Protection Lock Register
PR:
Protection Register
RCR:
Read Configuration Register
Datasheet
6
November 2007
Order Number: 306666-11
P30
RFU:
Reserved for Future Use
SR:
Status Register
WSM:
Write State Machine
1.3
Conventions
VCC:
Signal or voltage connection
VCC:
Signal or voltage level
0x:
Hexadecimal number prefix
0b:
Binary number prefix
SR[4]:
Denotes an individual register bit.
A[15:0]:
Denotes a group of similarly named signals, such as address or data bus.
A5:
Denotes one element of a signal group membership, such as an individual address bit.
Bit:
Binary unit
Byte:
Eight bits
Word:
Two bytes, or sixteen bits
Kbit:
1024 bits
KByte:
1024 bytes
KWord:
1024 words
Mbit:
1,048,576 bits
MByte:
1,048,576 bytes
MWord:
1,048,576 words
November 2007
Order Number: 306666-11
Datasheet
7
P30
2.0
Functional Overview
This section provides an overview of the features and capabilities of the P30.
The P30 family provides density upgrades from 64-Mbit through 512-Mbit. This family
of devices provides high performance at low voltage on a 16-bit data bus. Individually
erasable memory blocks are sized for optimum code and data storage.
Upon initial power up or return from reset, the device defaults to asynchronous pagemode read. Configuring the Read Configuration Register enables synchronous burstmode reads. In synchronous burst mode, output data is synchronized with a usersupplied clock signal. A WAIT signal provides an easy CPU-to-flash memory
synchronization.
In addition to the enhanced architecture and interface, the device incorporates
technology that enables fast factory program and erase operations. Designed for lowvoltage systems, the
P30 supports read operations with VCC at 1.8 V, and erase and program operations with
VPP at 1.8 V or 9.0 V. Buffered Enhanced Factory Programming (BEFP) provides the
fastest flash array programming performance with VPP at 9.0 V, which increases factory
throughput. With VPP at 1.8 V, VCC and VPP can be tied together for a simple, ultra low
power design. In addition to voltage flexibility, a dedicated VPP connection provides
complete data protection when VPP ≤ VPPLK.
A Command User Interface (CUI) is the interface between the system processor and all
internal operations of the device. An internal Write State Machine (WSM) automatically
executes the algorithms and timings necessary for block erase and program. A Status
Register indicates erase or program completion and any errors that may have occurred.
An industry-standard command sequence invokes program and erase automation. Each
erase operation erases one block. The Erase Suspend feature allows system software to
pause an erase cycle to read or program data in another block. Program Suspend
allows system software to pause programming to read other locations. Data is
programmed in word increments (16 bits).
The P30 protection register allows unique flash device identification that can be used to
increase system security. The individual Block Lock feature provides zero-latency block
locking and unlocking. In addition, the P30 device also has four pre-defined spaces in
the main array that can be configured as One-Time Programmable (OTP).
2.1
Virtual Chip Enable Description
The P30 512Mbit devices employ a Virtual Chip Enable which combines two 256-Mbit
die with a common chip enable, F1-CE# for QUAD+ packages or CE# for Easy BGA and
TSOP packages. (Refer to Figure 9 on page 21 and Figure 10 on page 21). Address A24
(Quad+ package) or A25 (Easy BGA and TSOP packages) is then used to select
between the die pair with F1-CE# / CE# asserted depending upon the package option
used. When chip enable is asserted and QUAD+ A24 (Easy BGA/TSOP A25) is low (VIL),
The lower parameter die is selected; when chip enable is asserted and QUAD+ A24
(Easy BGA/TSOP A25) is high (VIH), the upper parameter die is selected. Refer to
Table 1 and Table 2 for additional details.
Table 1:
Virtual Chip Enable Truth Table for 512 Mb (QUAD+ Package)
Die Selected
F1-CE#
A24
Lower Param Die
L
L
Upper Param Die
L
H
Datasheet
8
November 2007
Order Number: 306666-11
P30
Table 2:
Virtual Chip Enable Truth Table for 512 Mb (Easy BGA & TSOP Packages)
Die Selected
CE#
A25
Lower Param Die
L
L
Upper Param Die
L
H
November 2007
Order Number: 306666-11
Datasheet
9
P30
3.0
Package Information
3.1
56-Lead TSOP
Figure 1:
TSOP Mechanical Specifications
Z
A2
See Note 2
See Notes 1 and 3
Pin 1
e
See Detail B
E
Y
D1
A1
D
Seating
Plane
See Detail A
A
Detail A
Detail B
C
0
b
L
[231369-90]
Table 3:
TSOP Package Dimensions (Sheet 1 of 2)
Millimeters
Product Information
Inches
Symbol
Notes
Min
Nom
Max
Min
Nom
Max
A
-
-
1.200
-
-
0.047
Standoff
A1
0.050
-
-
0.002
-
-
Package Body Thickness
A2
0.965
0.995
1.025
0.038
0.039
0.040
Lead Width
b
0.100
0.150
0.200
0.004
0.006
0.008
Lead Thickness
c
0.100
0.150
0.200
0.004
0.006
0.008
Package Body Length
D1
18.200
18.400
18.600
0.717
0.724
0.732
Package Body Width
E
13.800
14.000
14.200
0.543
0.551
0.559
Package Height
Lead Pitch
e
-
0.500
-
-
0.0197
-
Terminal Dimension
D
19.800
20.00
20.200
0.780
0.787
0.795
Datasheet
10
November 2007
Order Number: 306666-11
P30
Table 3:
TSOP Package Dimensions (Sheet 2 of 2)
Millimeters
Product Information
Inches
Symbol
Notes
Min
Nom
Max
Min
Nom
Max
0.500
0.600
0.700
0.020
0.024
0.028
Lead Tip Length
L
Lead Count
N
-
56
-
-
56
-
Lead Tip Angle
ý
0°
3°
5°
0°
3°
5°
Seating Plane Coplanarity
Y
-
-
0.100
-
-
0.004
Lead to Package Offset
Z
0.150
0.250
0.350
0.006
0.010
0.014
Notes:
1.
2.
3.
4.
One dimple on package denotes Pin 1.
If two dimples, then the larger dimple denotes Pin 1.
Pin 1 will always be in the upper left corner of the package, in reference to the product mark.
Daisy Chain Evaluation Unit information is at Numonyx™ Flash Memory Packaging Technology
http://developer.Numonyx.com/design/flash/packtech.
3.2
64-Ball Easy BGA Package
Figure 2:
Easy BGA Mechanical Specifications
Ball A1
Corner
D
1
E
Ball A1
Corner
2
3
4
S1
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
Top View - Ball side down
7
6
5
4
3
2
1
S2
b
e
Bottom View - Ball Side Up
A1
A2
A
Seating
Plane
Y
Note: Drawing not to scale
November 2007
Order Number: 306666-11
Datasheet
11
P30
Table 4:
Easy BGA Package Dimensions
Millimeters
Product Information
Package Height (64/128/256-Mbit)
Package Height (512-Mbit)
Inches
Symbol
A
Notes
Min
Nom
Max
Min
Nom
Max
-
-
1.200
-
-
0.0472
A
-
-
1.300
-
-
0.0512
Ball Height
A1
0.250
-
-
0.0098
-
-
Package Body Thickness (64/128/256Mbit)
A2
-
0.780
-
-
0.0307
-
Package Body Thickness (512-Mbit)
A2
-
0.910
-
-
0.0358
-
Ball (Lead) Width
b
0.330
0.430
0.530
0.0130
0.0169
0.0209
Package Body Width
D
9.900
10.000
10.100
0.3898
0.3937
0.3976
E
12.900
13.000
13.100
0.5079
0.5118
0.5157
[e]
-
1.000
-
-
0.0394
-
Package Body Length
Pitch
Ball (Lead) Count
N
-
64
-
-
64
-
Seating Plane Coplanarity
Y
-
-
0.100
-
-
0.0039
Corner to Ball A1 Distance Along D
S1
1.400
1.500
1.600
0.0551
0.0591
0.0630
Corner to Ball A1 Distance Along E
S2
2.900
3.000
3.100
0.1142
0.1181
0.1220
Notes:
1.
Daisy Chain Evaluation Unit information is at Numonyx™ Flash Memory Packaging Technology
http://developer.Numonyx.com/design/flash/packtech.
Datasheet
12
November 2007
Order Number: 306666-11
P30
3.3
Figure 3:
QUAD+ SCSP Packages
64/128-Mbit, 88-ball (80 active) QUAD+ SCSP Specifications (8x10x1.2 mm)
A1 Index
Mark
S1
1
2
3
4
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
D
7
6
5
4
3
2
1
S2
F
G
G
H
H
J
J
K
K
L
L
M
M
e
b
E
Top View - Ball
Down
A2
Bottom View - Ball Up
A1
A
Y
D raw ing not to sc ale.
Dimensions
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Width
Package Body Length
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along E
Corner to Ball A1 Distance Along D
November 2007
Order Number: 306666-11
Symbol
A
A1
A2
b
D
E
e
N
Y
S1
S2
Min
0.200
0.325
9.900
7.900
1.100
0.500
Millimeters
Nom
Max
1.200
0.860
0.375
0.425
10.000
10.100
8.000
8.100
0.800
88
0.100
1.200
1.300
0.600
0.700
Min
0.0079
0.0128
0.3898
0.3110
0.0433
0.0197
Inches
Nom
0.0339
0.0148
0.3937
0.3150
0.0315
88
0.0472
0.0236
Max
0.0472
0.0167
0.3976
0.3189
0.0039
0.0512
0.0276
Datasheet
13
P30
Figure 4:
256-Mbit, 88-ball (80 active) QUAD+ SCSP Specifications (8x11x1.0 mm)
S1
A 1 Index
Mark
1
2
3
4
5
6
7
8
8
A
A
B
B
C
C
D
D
E
E
F
D
7
6
5
4
3
2
1
S2
F
G
G
H
H
J
K
K
e
J
L
L
M
M
b
E
Bottom View - Ball Up
Top View - Ball Down
A2
A1
A
Y
D raw ing not to scale.
Note: Dimensions A1, A2, and b are preliminary
Dimensions
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Length
Package Body Width
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along E
Corner to Ball A1 Distance Along D
Datasheet
14
Symbol
A
A1
A2
b
D
E
e
N
Y
S1
S2
Min
0.117
0.300
10.900
7.900
1.100
1.000
Millimeters
Nom
Max
1.000
0.740
0.350
0.400
11.00
11.100
8.00
8.100
0.80
88
0.100
1.200
1.300
1.100
1.200
Min
0.0046
0.0118
0.4291
0.3110
0.0433
0.0394
Inches
Nom
0.0291
0.0138
0.4331
0.3150
0.0315
88
0.0472
0.0433
Max
0.0394
0.0157
0.4370
0.3189
0.0039
0.0512
0.0472
November 2007
Order Number: 306666-11
P30
Figure 5:
512-Mbit, 88-ball (80 active) QUAD+ SCSP Specifications (8x11x1.2 mm)
S1
A 1 Index
Mark
1
2
3
4
5
6
7
8
8
A
A
B
B
C
C
D
D
7
6
5
4
3
2
1
S2
E
E
F
D
F
G
G
H
H
J
K
K
e
J
L
L
M
M
b
E
Bottom View - Ball Up
Top View - Ball Down
A2
A1
A
Y
D raw ing not to scale .
Dimensions
Package Height
Ball Height
Package Body Thickness
Ball (Lead) Width
Package Body Length
Package Body Width
Pitch
Ball (Lead) Count
Seating Plane Coplanarity
Corner to Ball A1 Distance Along E
Corner to Ball A1 Distance Along D
November 2007
Order Number: 306666-11
Symbol
A
A1
A2
b
D
E
e
N
Y
S1
S2
Min
0.200
0.325
10.900
7.900
1.100
1.000
Millimeters
Nom
Max
1.200
0.860
0.375
0.425
11.000
11.100
8.000
8.100
0.800
88
0.100
1.200
1.300
1.100
1.200
Min
0.0079
0.0128
0.4291
0.3110
0.0433
0.0394
Inches
Nom
0.0339
0.0148
0.4331
0.3150
0.0315
88
0.0472
0.0433
Max
0.0472
0.0167
0.4370
0.3189
0.0039
0.0512
0.0472
Datasheet
15
P30
4.0
Ballout and Signal Descriptions
4.1
Signal Ballout
Figure 6:
56-Lead TSOP Pinout (64/128/256/512- Mbit)
A16
A15
A14
A13
A12
A11
A10
A9
A23
A22
A21
VSS
VCC
WE#
WP#
A20
A19
A18
A8
A7
A6
A5
A4
A3
A2
A24
A25
VSS
Notes:
1.
2.
3.
4.
5.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Intel StrataFlash®
Embedded Memory (P30)
56-Lead TSOP Pinout
14 mm x 20 mm
Top View
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
WAIT
A17
DQ15
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
ADV#
CLK
RST#
VPP
DQ11
DQ3
DQ10
DQ2
VCCQ
DQ9
DQ1
DQ8
DQ0
VCC
OE#
VSS
CE#
A1
A1 is the least significant address bit.
A23 is valid for 128-Mbit densities and above; otherwise, it is a no connect (NC).
A24 is valid for 256-Mbit densities; otherwise, it is a no connect (NC).
A25 is valid for 512-Mbit densities; otherwise, it is a no connect (NC).
Please refer to the latest specification update for synchronous read operation with the TSOP package. The synchronous read
input signals (i.e. ADV# and CLK) should be tied off to support asynchronous reads. See Section 4.2, “Signal Descriptions”
on page 19.
Datasheet
16
November 2007
Order Number: 306666-11
P30
Figure 7:
64-Ball Easy BGA Ballout (64/128/256/512-Mbit)
1
2
3
4
5
6
7
8
8
7
A1
A6
A8
VPP
A13
VCC
A18
A22
A22
A18
A2
VSS
A9
CE#
A14
A25
A19 RFU
RFU
A3
A7
A10
A12
A15
WP#
A20
A21
A4
A5
A11 RST# VCCQ VCCQ A16
A17
6
5
4
3
2
1
VCC A13
VPP
A8
A6
A1
A19
A25
A14
CE#
A9
VSS
A2
A21
A20
WP#
A15
A12
A10
A7
A3
A17
A16 VCCQ VCCQ RST# A11
A5
A4
A
A
B
B
C
C
D
D
E
E
DQ4 DQ3 DQ9 DQ1
DQ8
RFU DQ0 DQ10 DQ11 DQ12 ADV# WAIT OE#
OE# WAIT ADV# DQ12 DQ11 DQ10 DQ0
RFU
A23
RFU
WE# DQ14 DQ6
DQ5 VCCQ DQ2
RFU
A23
RFU
VSS VCC VSS DQ13 VSS DQ7
A24
DQ13 VSS VCC
VSS
RFU
DQ8
DQ1 DQ9
DQ3 DQ4
CLK DQ15 RFU
RFU DQ15 CLK
F
F
G
G
DQ2 VCCQ DQ5 DQ6
DQ14 WE#
H
H
Easy BGA
Top View- Ball side down
Notes:
1.
2.
3.
4.
A24
DQ7
VSS
Easy BGA
Bottom View- Ball side up
A1 is the least significant address bit.
A23 is valid for 128-Mbit densities and above; otherwise, it is a no connect (NC).
A24 is valid for 256-Mbit densities and above; otherwise, it is a no connect (NC).
A25 is valid for 512-Mbit densities; otherwise, it is a no connect (NC).
November 2007
Order Number: 306666-11
Datasheet
17
P30
Figure 8:
88-Ball (80-Active Ball) QUAD+ SCSP Ballout
Pin 1
Notes:
1.
2.
3.
4.
1
2
3
4
5
6
7
8
A
DU
DU
Depop
Depop
Depop
Depop
DU
DU
A
B
A4
A18
A19
VSS
VCC
VCC
A21
A11
B
C
A5
RFU
A23
VSS
RFU
CLK
A22
A12
C
D
A3
A17
A24
VPP
RFU
RFU
A9
A13
D
E
A2
A7
RFU
WP#
ADV#
A20
A10
A15
E
F
A1
A6
RFU
RST#
WE#
A8
A14
A16
F
G
A0
DQ8
DQ2
DQ10
DQ5
DQ13
WAIT
F2-CE#
G
H
RFU
DQ0
DQ1
DQ3
DQ12
DQ14
DQ7
F2-OE#
H
J
RFU
F1-OE#
DQ9
DQ11
DQ4
DQ6
DQ15
VCCQ
J
K
F1-CE#
RFU
RFU
RFU
RFU
VCC
VCCQ
RFU
K
L
VSS
VSS
VCCQ
VCC
VSS
VSS
VSS
VSS
L
M
DU
DU
Depop
Depop
Depop
Depop
DU
DU
M
1
2
3
4
5
6
7
8
A22 is valid for 128-Mbit densities and above; otherwise, it is a no connect (NC).
A23 is valid for 256-Mbit densities and above; otherwise, it is a no connect (NC).
A24 is valid for 512-Mbit densities and above; otherwise, it is a no connect (NC).
F2-CE# and F2-OE# are no connect (NC) for all densities.
Datasheet
18
November 2007
Order Number: 306666-11
P30
4.2
Signal Descriptions
This section has signal descriptions for the various P30 packages.
Table 5:
Symbol
TSOP and Easy BGA Signal Descriptions (Sheet 1 of 2)
Type
Name and Function
A[MAX:1]
Input
ADDRESS INPUTS: Device address inputs. 64-Mbit: A[22:1]; 128-Mbit: A[23:1]; 256-Mbit:
A[24:1]; 512-Mbit: A[25:1]. Note: The virtual selection of the 256-Mbit “Top parameter” die in the
dual-die 512-Mbit configuration is accomplished by setting A[25] high (VIH).
DQ[15:0]
Input/
Output
DATA INPUT/OUTPUTS: Inputs data and commands during write cycles; outputs data during
memory, Status Register, Protection Register, and Read Configuration Register reads. Data balls float
when the CE# or OE# are deasserted. Data is internally latched during writes.
Input
ADDRESS VALID: Active low input. During synchronous read operations, addresses are latched on
the rising edge of ADV#, or on the next valid CLK edge with ADV# low, whichever occurs first.
In asynchronous mode, the address is latched when ADV# going high or continuously flows through
if ADV# is held low.
WARNING: Designs not using ADV# must tie it to VSS to allow addresses to flow through.
Input
FLASH CHIP ENABLE: Active low input. CE# low selects the associated flash memory die. When
asserted, flash internal control logic, input buffers, decoders, and sense amplifiers are active. When
deasserted, the associated flash die is deselected, power is reduced to standby levels, data and
WAIT outputs are placed in high-Z state.
WARNING: Chip enable must be driven high when device is not in use.
CLK
Input
CLOCK: Synchronizes the device with the system’s bus frequency in synchronous-read mode. During
synchronous read operations, addresses are latched on the rising edge of ADV#, or on the next valid
CLK edge with ADV# low, whichever occurs first.
WARNING: Designs not using CLK for synchronous read mode must tie it to VCCQ or VSS.
OE#
Input
OUTPUT ENABLE: Active low input. OE# low enables the device’s output data buffers during read
cycles. OE# high places the data outputs and WAIT in High-Z.
RST#
Input
RESET: Active low input. RST# resets internal automation and inhibits write operations. This
provides data protection during power transitions. RST# high enables normal operation. Exit from
reset places the device in asynchronous read array mode.
ADV#
CE#
WAIT
Output
WAIT: Indicates data valid in synchronous array or non-array burst reads. Read Configuration
Register bit 10 (RCR[10], WT) determines its polarity when asserted. WAIT’s active output is VOL or
VOH when CE# and OE# are VIL. WAIT is high-Z if CE# or OE# is VIH.
• In synchronous array or non-array read modes, WAIT indicates invalid data when asserted and
valid data when deasserted.
• In asynchronous page mode, and all write modes, WAIT is deasserted.
WE#
Input
WRITE ENABLE: Active low input. WE# controls writes to the device. Address and data are latched
on the rising edge of WE#.
WP#
Input
WRITE PROTECT: Active low input. WP# low enables the lock-down mechanism. Blocks in lockdown cannot be unlocked with the Unlock command. WP# high overrides the lock-down function
enabling blocks to be erased or programmed using software commands.
VPP
Power/
Input
Erase and Program Power: A valid voltage on this pin allows erasing or programming. Memory
contents cannot be altered when VPP ≤ VPPLK. Block erase and program at invalid VPP voltages should
not be attempted.
Set VPP = VPPL for in-system program and erase operations. To accommodate resistor or diode drops
from the system supply, the VIH level of VPP can be as low as VPPL min. VPP must remain above VPPL
min to perform in-system flash modification. VPP may be 0 V during read operations.
VPPH can be applied to main blocks for 1000 cycles maximum and to parameter blocks for 2500
cycles. VPP can be connected to 9 V for a cumulative total not to exceed 80 hours. Extended use of
this pin at 9 V may reduce block cycling capability.
VCC
Power
Device Core Power Supply: Core (logic) source voltage. Writes to the flash array are inhibited
when VCC ≤ VLKO. Operations at invalid VCC voltages should not be attempted.
VCCQ
Power
Output Power Supply: Output-driver source voltage.
VSS
Power
Ground: Connect to system ground. Do not float any VSS connection.
November 2007
Order Number: 306666-11
Datasheet
19
P30
Table 5:
Symbol
TSOP and Easy BGA Signal Descriptions (Sheet 2 of 2)
Type
Name and Function
RFU
—
Reserved for Future Use: Reserved by Numonyx for future device functionality and enhancement.
These should be treated in the same way as a Do Not Use (DU) signal.
DU
—
Do Not Use: Do not connect to any other signal, or power supply; must be left floating.
NC
—
No Connect: No internal connection; can be driven or floated.
Table 6:
Symbol
QUAD+ SCSP Signal Descriptions (Sheet 1 of 2)
Type
Name and Function
A[MAX:0]
Input
ADDRESS INPUTS: Device address inputs. 64-Mbit: A[21:0]; 128-Mbit: A[22:0]; 256-Mbit:
A[23:0]; 512-Mbit: A[24:0]. Note: The virtual selection of the 256-Mbit “Top parameter” die in the
dual-die 512-Mbit configuration is accomplished by setting A[25] high (VIH).
DQ[15:0]
Input/
Output
DATA INPUT/OUTPUTS: Inputs data and commands during write cycles; outputs data during
memory, Status Register, Protection Register, and Read Configuration Register reads. Data balls float
when the CE# or OE# are deasserted. Data is internally latched during writes.
Input
ADDRESS VALID: Active low input. During synchronous read operations, addresses are latched on
the rising edge of ADV#, or on the next valid CLK edge with ADV# low, whichever occurs first.
In asynchronous mode, the address is latched when ADV# going high or continuously flows through
if ADV# is held low.
WARNING: Designs not using ADV# must tie it to VSS to allow addresses to flow through.
F1-CE#
Input
FLASH CHIP ENABLE: Active low input. CE# low selects the associated flash memory die. When
asserted, flash internal control logic, input buffers, decoders, and sense amplifiers are active. When
deasserted, the associated flash die is deselected, power is reduced to standby levels, data and
WAIT outputs are placed in high-Z state.
WARNING: Chip enable must be driven high when device is not in use.
CLK
Input
CLOCK: Synchronizes the device with the system’s bus frequency in synchronous-read mode. During
synchronous read operations, addresses are latched on the rising edge of ADV#, or on the next valid
CLK edge with ADV# low, whichever occurs first.
WARNING: Designs not using CLK for synchronous read mode must tie it to VCCQ or VSS.
F1-OE#
Input
OUTPUT ENABLE: Active low input. OE# low enables the device’s output data buffers during read
cycles. OE# high places the data outputs and WAIT in High-Z.
RST#
Input
RESET: Active low input. RST# resets internal automation and inhibits write operations. This
provides data protection during power transitions. RST# high enables normal operation. Exit from
reset places the device in asynchronous read array mode.
ADV#
WAIT
Output
WAIT: Indicates data valid in synchronous array or non-array burst reads. Read Configuration
Register bit 10 (RCR[10], WT) determines its polarity when asserted. WAIT’s active output is VOL or
VOH when CE# and OE# are VIL. WAIT is high-Z if CE# or OE# is VIH.
• In synchronous array or non-array read modes, WAIT indicates invalid data when asserted and
valid data when deasserted.
• In asynchronous page mode, and all write modes, WAIT is deasserted.
WE#
Input
WRITE ENABLE: Active low input. WE# controls writes to the device. Address and data are latched
on the rising edge of WE#.
WP#
Input
WRITE PROTECT: Active low input. WP# low enables the lock-down mechanism. Blocks in lockdown cannot be unlocked with the Unlock command. WP# high overrides the lock-down function
enabling blocks to be erased or programmed using software commands.
VPP
Datasheet
20
Power/
lnput
Erase and Program Power: A valid voltage on this pin allows erasing or programming. Memory
contents cannot be altered when VPP ≤ VPPLK . Block erase and program at invalid VPP voltages should
not be attempted.
Set VPP = VPPL for in-system program and erase operations. To accommodate resistor or diode drops
from the system supply, the VIH level of VPP can be as low as VPPL min. VPP must remain above VPPL
min to perform in-system flash modification. VPP may be 0 V during read operations.
VPPH can be applied to main blocks for 1000 cycles maximum and to parameter blocks for 2500
cycles. VPP can be connected to 9 V for a cumulative total not to exceed 80 hours. Extended use of
this pin at 9 V may reduce block cycling capability.
November 2007
Order Number: 306666-11
P30
Table 6:
Symbol
QUAD+ SCSP Signal Descriptions (Sheet 2 of 2)
Type
Name and Function
VCC
Power
Device Core Power Supply: Core (logic) source voltage. Writes to the flash array are inhibited
when VCC ≤ VLKO. Operations at invalid VCC voltages should not be attempted.
VCCQ
Power
Output Power Supply: Output-driver source voltage.
VSS
Power
Ground: Connect to system ground. Do not float any VSS connection.
RFU
—
Reserved for Future Use: Reserved by Numonyx for future device functionality and enhancement.
These should be treated in the same way as a Do Not Use (DU) signal.
DU
—
Do Not Use: Do not connect to any other signal, or power supply; must be left floating.
NC
—
No Connect: No internal connection; can be driven or floated.
4.3
Dual-Die Configurations
Figure 9:
512-Mbit Easy BGA and TSOP Top or Bottom Parameter Block Diagram
Easy BGA & TSOP 512-Mbit (Dual-Die) Top or Bottom Parameter
Configuration
CE#
Top Param Die
(256-Mbit)
WP#
OE#
WE#
RST#
VCC
VPP
VCCQ
VSS
CLK
ADV#
Bottom Param Die
(256-Mbit)
A[MAX:1]
DQ[15:0]
WAIT
Figure 10: 512-Mbit QUAD+ SCSP Top or Bottom Parameter Block Diagram
QUAD+ 512-Mbit (Dual-Die) Top or Bottom Parameter
Configuration
F1-CE#
WP#
Top Param Die
(256-Mbit)
OE#
VCCQ
CLK
ADV#
VSS
Bottom Param Die
(256-Mbit)
Note:
VCC
VPP
WE#
A[MAX:0]
RST#
DQ[15:0]
WAIT
Amax = Vih selects the Top parameter Die; Amax = Vil selects the Bottom Parameter Die.
November 2007
Order Number: 306666-11
Datasheet
21
P30
4.4
Memory Maps
Table 7 through Table 9 show the P30 memory maps. The memory array is divided into
multiple 8-Mbit Programming Regions (see Section 11.0, “Programming Operations” on
page 56).
66
3FC000 - 3FFFFF
32
130
7FC000 - 7FFFFF
780000 - 78FFFF
128
119
770000 - 77FFFF
128
118
760000 - 76FFFF
360000 - 36FFFF
010000 - 01FFFF
128
0
000000 - 00FFFF
Size
(KB)
Blk
256-Mbit
32
258
FFC000 - FFFFFF
FF0000 - FF3FFF
128
254
FE0000 - FEFFFF
248
F80000 - F8FFFF
128
247
F70000 - F7FFFF
128
246
F60000 - F6FFFF
...
128
...
...
255
...
32
...
...
1
...
128
...
...
370000 - 37FFFF
54
...
55
...
128
128
128
1
010000 - 01FFFF
128
0
000000 - 00FFFF
...
120
...
128
...
380000 - 38FFFF
Fifteen
Programming
Regions
...
7E0000 - 7EFFFF
...
7F0000 - 7F3FFF
126
56
128
1
010000 - 01FFFF
128
0
000000 - 00FFFF
Discrete Bottom Parameter Memory Maps (all packages)
64-Mbit
Size
(KB)
Blk
128
130
7F0000 - 7FFFFF
128
129
7E0000 - 7EFFFF
12
090000 - 09FFFF
128
11
080000 - 08FFFF
...
128
...
3F0000 - 3FFFFF
3E0000 - 3EFFFF
...
66
65
...
128
128
128-Mbit
...
Blk
...
Seven
Programming
Regions
127
128
Size
(KB)
Datasheet
22
32
128
...
3E0000 - 3EFFFF
...
3F0000 - 3F3FFF
62
...
63
...
32
128
...
32
...
128-Mbit
...
Blk
One
Programming
Region
Size
(KB)
...
64-Mbit
...
Blk
...
Size
(KB)
Fifteen
Programming
Regions
Table 8:
Discrete Top Parameter Memory Maps (all packages)
...
Thirty-One
Programming
Regions
One
Programming
Region
Seven
Programming
Regions
One
Programming
Region
Table 7:
128
12
090000 - 09FFFF
128
11
080000 - 08FFFF
November 2007
Order Number: 306666-11
P30
10
070000 - 07FFFF
128
10
070000 - 07FFFF
...
...
00C000 - 00FFFF
000000 - 003FFF
Size
(KB)
Blk
256-Mbit
128
258
FF0000 - FFFFFF
128
257
FE0000 - FEFFFF
11
080000 - 08FFFF
128
10
070000 - 07FFFF
...
128
128
4
010000 - 01FFFF
32
3
00C000 - 00FFFF
...
090000 - 09FFFF
...
12
...
128
...
...
0
...
32
...
...
010000 - 01FFFF
3
...
4
32
...
128
32
0
000000 - 003FFF
...
128
128
4
010000 - 01FFFF
32
3
00C000 - 00FFFF
...
128-Mbit
...
Blk
...
Size
(KB)
...
64-Mbit
...
Blk
One
Programming
Region
Size
(KB)
...
Discrete Bottom Parameter Memory Maps (all packages)
...
One
Programming
Region
Thirty-One
Programming
Regions
One
Programming
Region
Table 8:
32
0
000000 - 003FFF
Block size is referenced in K-Bytes where a byte=8 bits. Block Address range is referenced in KWords where a Word is the size of the flash output bus (16 bits).
Note:
The Dual- Die P30 memory maps are the same for both parameter options because the
devices employ virtual chip enable (Refer to Section 2.1). The parameter option only defines
the placement of bottom parameter die.
Table 9:
512-Mbit Top and Bottom Parameter Memory Map (Easy BGA and QUAD+ SCSP)
(Sheet 1 of 2)
512-Mbit Flash (2x256-Mbit w/ 1CE)
Die Stack Config
Size
(KB)
Blk
Address Range
32
517
1FFC000 - 1FFFFFF
...
...
...
256-Mbit
32
514
1FF0000 - 1FF3FFF
Top Parameter Die
128
513
1FE0000 - 1FEFFFF
...
...
...
November 2007
Order Number: 306666-11
128
259
1000000 - 100FFFF
128
258
FF0000 - FFFFFF
Datasheet
23
P30
Table 9:
512-Mbit Top and Bottom Parameter Memory Map (Easy BGA and QUAD+ SCSP)
(Sheet 2 of 2)
512-Mbit Flash (2x256-Mbit w/ 1CE)
Size
(KB)
Blk
...
...
256-Mbit
128
4
010000 - 01FFFF
Bottom Parameter Die
32
3
00C000 - 00FFFF
...
...
...
32
0
000000 - 003FFF
Address Range
...
Note:
Die Stack Config
Refer to the appropriate 256-Mbit Memory Map (Table 7 or Table 8) for Programming Region information; Block size
is referenced in K-Bytes where a byte=8 bits. Block Address range is referenced in K-Words where a Word is the size of
the flash output bus (16 bits).
Datasheet
24
November 2007
Order Number: 306666-11
P30
5.0
Maximum Ratings and Operating Conditions
5.1
Absolute Maximum Ratings
Warning:
Stressing the device beyond the “Absolute Maximum Ratings” may cause permanent
damage. These are stress ratings only.
Table 10:
Parameter
Maximum Rating
Temperature under bias
Notes
–40 °C to +85 °C
Storage temperature
–65 °C to +125 °C
Voltage on any signal (except VCC, VPP and VCCQ)
–0.5 V to +4.1 V
1
VPP voltage
–0.2 V to +10 V
1,2,3
VCC voltage
–0.2 V to +2.5 V
1
VCCQ voltage
–0.2 V to +4.1 V
1
100 mA
4
Output short circuit current
Notes:
1.
Voltages shown are specified with respect to VSS. Minimum DC voltage is –0.5 V on input/output signals and –0.2 V on
VCC, VCCQ, and VPP. During transitions, this level may undershoot to –2.0 V for periods less than 20 ns. Maximum DC
voltage on VCC is VCC + 0.5 V, which, during transitions, may overshoot to VCC + 2.0 V for periods less than 20 ns.
Maximum DC voltage on input/output signals and VCCQ is VCCQ + 0.5 V, which, during transitions, may overshoot to
VCCQ + 2.0 V for periods less than 20 ns.
2.
Maximum DC voltage on VPP may overshoot to +11.5 V for periods less than 20 ns.
3.
Program/erase voltage is typically 1.7 V – 2.0 V. 9.0 V can be applied for 80 hours maximum total, to any blocks for
1000 cycles maximum. 9.0 V program/erase voltage may reduce block cycling capability.
4.
Output shorted for no more than one second. No more than one output shorted at a time.
5.2
Note:
Operating Conditions
Operation beyond the “Operating Conditions” is not recommended and extended exposure
beyond the “Operating Conditions” may affect device reliability.
Table 11: Operating Conditions
Symbol
TC
VCC
Parameter
Operating Temperature
VCC Supply Voltage
Min
Max
Units
Notes
–40
+85
°C
1
1.7
2.0
CMOS inputs
1.7
3.6
TTL inputs
2.4
3.6
0.9
3.6
VCCQ
I/O Supply Voltage
VPPL
VPP Voltage Supply (Logic Level)
VPPH
Factory word programming VPP
8.5
9.5
tPPH
Maximum VPP Hours
VPP = VPPH
-
80
Main and Parameter Blocks
VPP = VPPL
100,000
-
Main Blocks
VPP = VPPH
-
1000
Parameter Blocks
VPP = VPPH
-
2500
Block
Erase
Cycles
3
V
Hours
2
Cycles
Notes:
1.
TC = Case Temperature.
2.
In typical operation VPP program voltage is VPPL.
3.
40Mhz burst operation on the TSOP package has a min Vcc value of 1.85V. Please refer to the latest Specification Update
regarding synchronous burst operation with the TSOP package
November 2007
Order Number: 306666-11
Datasheet
25
P30
6.0
Electrical Specifications
6.1
DC Current Characteristics
Table 12: DC Current Characteristics (Sheet 1 of 2)
Sym
Parameter
ILI
Input Load Current
ILO
Output
Leakage
Current
ICCS,
ICCD
DQ[15:0],
VCC Standby,
Power Down
ICCWS,
ICCES
-
±2
µA
VCC = VCCMax
VCCQ = VCCQ Max
VIN = VCCQ or VSS
µA
VCC = VCCMax
VCCQ = VCCQ Max
VIN = VCCQ or VSS
µA
VCC = VCCMax
VCCQ = VCCQ Max
CE# = VCCQ
RST# = VCCQ (for ICCS)
RST# = VSS (for ICCD )
WP# = VIH
20
35
128-Mbit
30
75
30
75
256-Mbit
55
115
55
200
512-Mbit
110
230
110
400
14
16
14
16
mA
1-Word Read
9
10
9
10
mA
4-Word Read
13
17
n/a
n/a
mA
BL = 4W
15
19
n/a
n/a
mA
BL = 8W
17
21
n/a
n/a
mA
BL = 16W
21
26
n/a
n/a
mA
BL = Cont.
16
19
n/a
n/a
mA
BL = 4W
19
23
n/a
n/a
mA
BL = 8W
22
26
n/a
n/a
mA
BL = 16W
23
28
n/a
n/a
mA
36
51
36
51
CE# = VCCQ; suspend in
progress
1,3,4
VPP = VPPL, suspend in progress
1,3
VPP = VPPL
1,3
35
128-Mbit
30
75
30
75
256-Mbit
55
115
55
200
512-Mbit
110
230
110
400
0.2
5
0.2
5
µA
µA
15
2
15
0.05
0.10
8
22
8
22
BL = Cont.
µA
33
20
0.10
1
1,3,5
26
35
2
1,2
VPP = VPPH, pgm/ers in progress
33
20
0.05
1
1,3,5
mA
26
VPP Read
VCC = VCCMax
CE# = VIL
OE# = VIH
Inputs: VIL or
VIH
Notes
VPP = VPPL, pgm/ers in progress
64-Mbit
IPPR
Datasheet
26
±1
35
VCC Program Current,
VCC Erase Current
VPP Program Current
-
20
IPPES
IPPW
Max
64-Mbit
VPP Standby Current,
VPP Program Suspend Current,
VPP Erase Suspend Current
IPPS,
IPPWS,
Typ
±10
Synchronous Burst
f = 40 MHz
VCC Program Suspend
Current,
VCC Erase
Suspend Current
Max
Test Conditions
-
Synchronous Burst
f = 52MHz
ICCW,
ICCE
Typ
Unit
±1
Page-Mode Read
f = 13 MHz (5 CLK)
ICCR
TTL Inputs
(V CCQ =
2.4 V - 3.6
V)
-
WAIT
Asynchronous SingleWord f = 5 MHz (1 CLK)
Average
VCC
Read
Current
CMOS
Inputs
(VCCQ =
1.7 V - 3.6
V)
mA
VPP = VPPL, program in progress
VPP = VPPH, program in progress
November 2007
Order Number: 306666-11
P30
Table 12: DC Current Characteristics (Sheet 2 of 2)
Sym
IPPE
Notes:
1.
2.
3.
4.
5.
6.2
Parameter
VPP Erase Current
CMOS
Inputs
(VCCQ =
1.7 V - 3.6
V)
TTL Inputs
(VCCQ =
2.4 V - 3.6
V)
Typ
Max
Typ
Max
0.05
0.10
0.05
0.10
8
22
8
22
Unit
mA
Test Conditions
Notes
VPP = VPPL, erase in progress
VPP = VPPH, erase in progress
All currents are RMS unless noted. Typical values at typical VCC , TC = +25 °C.
ICCS is the average current measured over any 5 ms time interval 5 µs after CE# is deasserted.
Sampled, not 100% tested.
ICCES is specified with the device deselected. If device is read while in erase suspend, current is ICCES plus ICCR.
ICCW, ICCE measured over typical or max times specified in Section 7.5, “Program and Erase
Characteristics” on page 39.
DC Voltage Characteristics
Table 13: DC Voltage Characteristics
Sym
Parameter
CMOS Inputs
(VCCQ = 1.7 V – 3.6 V)
TTL Inputs (1)
(VCCQ = 2.4 V – 3.6 V)
Min
Max
Min
Max
Unit
Test Condition
VIL
Input Low Voltage
0
0.4
0
0.6
V
VIH
Input High Voltage
VCCQ – 0.4 V
VCCQ
2.0
VCCQ
V
VOL
Output Low Voltage
-
0.1
-
0.1
V
VCC = VCCMin
VCCQ = VCCQMin
IOL = 100 µA
VOH
Output High Voltage
VCCQ – 0.1
-
VCCQ – 0.1
-
V
VCC = VCCMin
VCCQ = VCCQMin
IOH = –100 µA
VPPLK
VPP Lock-Out Voltage
-
0.4
-
0.4
V
VLKO
VCC Lock Voltage
1.0
-
1.0
-
V
VLKOQ
VCCQ Lock Voltage
0.9
-
0.9
-
V
Notes
2
3
Notes:
1.
Synchronous read mode is not supported with TTL inputs.
2.
VIL can undershoot to –0.4 V and VIH can overshoot to VCCQ + 0.4 V for durations of 20 ns or less.
3.
VPP ≤ VPPLK inhibits erase and program operations. Do not use VPPL and VPPH outside their valid ranges.
November 2007
Order Number: 306666-11
Datasheet
27
P30
7.0
AC Characteristics
7.1
AC Test Conditions
Figure 11: AC Input/Output Reference Waveform
VCCQ
Input VCCQ/2
Test Points
VCCQ/2 Output
0V
Note:
IO_REF.WMF
AC test inputs are driven at VCCQ for Logic "1" and 0 V for Logic "0." Input/output timing begins/ends at VCCQ/2. Input rise
and fall times (10% to 90%) < 5 ns. Worst case speed occurs at VCC = VCCMin.
Figure 12: Transient Equivalent Testing Load Circuit
Device
Under Test
Out
CL
Notes:
1.
See the following table for component values.
2.
Test configuration component value for worst-case speed conditions.
3.
CL includes jig capacitance.
.
Table 14: Test Configuration Component Value For Worst Case Speed Conditions
Test Configuration
CL (pF)
VCCQMin Standard Test
30
Figure 13: Clock Input AC Waveform
R201
CLK [C]
VIH
VIL
R202
Datasheet
28
R203
November 2007
Order Number: 306666-11
P30
7.2
Capacitance
Table 15: Capacitance
Parameter
Signals
Min
Typ
Max
Unit
Input Capacitance
Address, Data,
CE#, WE#, OE#,
RST#, CLK, ADV#,
WP#
2
6
7
pF
Output Capacitance
Data, WAIT
2
4
5
pF
Condition
Notes
Typ temp = 25 °C,
Max temp = 85 °C,
VCC = (0 V - 2.0 V),
VCCQ = (0 V - 3.6 V),
Discrete silicon die
1,2,3
Notes:
1.
Capacitance values are for a single die; for 2-die and 4-die stacks, multiply the capacitance values by the number of
dies in the stack.
2.
Sampled, but not 100% tested.
3.
Silicon die capacitance only; add 1 pF for discrete packages.
7.3
AC Read Specifications
Table 16: AC Read Specifications for 64/128- Mbit Densities (Sheet 1 of 2)
Num
Symbol
Parameter
Min
Max
Unit
85
-
ns
Notes
Asynchronous Specifications
R1
tAVAV
Read cycle time
R2
tAVQV
Address to output valid
-
85
ns
R3
tELQV
CE# low to output valid
-
85
ns
R4
tGLQV
OE# low to output valid
-
25
ns
1,2
R5
tPHQV
RST# high to output valid
-
150
ns
1
R6
tELQX
CE# low to output in low-Z
0
-
ns
1,3
R7
tGLQX
OE# low to output in low-Z
0
-
ns
1,2,3
R8
tEHQZ
CE# high to output in high-Z
-
24
ns
R9
tGHQZ
OE# high to output in high-Z
-
24
ns
R10
tOH
Output hold from first occurring address, CE#, or
OE# change
0
-
ns
R11
tEHEL
CE# pulse width high
20
-
ns
R12
tELTV
CE# low to WAIT valid
-
17
ns
R13
tEHTZ
CE# high to WAIT high-Z
-
20
ns
1,3
R15
tGLTV
1
OE# low to WAIT valid
-
17
ns
R16
tGLTX
OE# low to WAIT in low-Z
0
-
ns
R17
tGHTZ
OE# high to WAIT in high-Z
-
20
ns
1,3
1
1,3
Latching Specifications
R101
tAVVH
Address setup to ADV# high
10
-
ns
R102
tELVH
CE# low to ADV# high
10
-
ns
R103
tVLQV
ADV# low to output valid
-
85
ns
R104
tVLVH
ADV# pulse width low
10
-
ns
R105
tVHVL
ADV# pulse width high
10
-
ns
R106
tVHAX
Address hold from ADV# high
9
-
ns
November 2007
Order Number: 306666-11
1
1,4
Datasheet
29
P30
Table 16: AC Read Specifications for 64/128- Mbit Densities (Sheet 2 of 2)
Num
Symbol
Parameter
R108
tAPA
Page address access
R111
tphvh
RST# high to ADV# high
Min
Max
Unit
-
25
ns
30
-
ns
-
52
MHz
Notes
1
Clock Specifications
R200
fCLK
CLK frequency
TSOP
-
40
MHz
19.2
-
ns
25
-
ns
R201
tCLK
CLK period
R202
tCH/CL
CLK high/low time
5
-
ns
R203
tFCLK/RCLK
CLK fall/rise time
-
3
ns
TSOP
1,3,5,6
(5,6)
Synchronous Specifications
R301
tAVCH/L
Address setup to CLK
9
-
ns
R302
tVLCH/L
ADV# low setup to CLK
9
-
ns
R303
tELCH/L
CE# low setup to CLK
9
-
ns
R304
tCHQV / tCLQV
CLK to output valid
-
17
ns
1
R305
tCHQX
Output hold from CLK
3
-
ns
1,7
R306
tCHAX
Address hold from CLK
10
-
ns
1,4,7
R307
tCHTV
CLK to WAIT valid
-
17
ns
1,7
R311
tCHVL
CLK Valid to ADV# Setup
3
-
ns
1
R312
tCHTX
WAIT Hold from CLK
3
-
ns
1,7
Notes:
1.
See Figure 11, “AC Input/Output Reference Waveform” on page 28 for timing measurements and max
allowable input slew rate.
2.
OE# may be delayed by up to tELQV – tGLQV after CE#’s falling edge without impact to tELQV.
3.
Sampled, not 100% tested.
4.
Address hold in synchronous burst mode is tCHAX or tVHAX , whichever timing specification is satisfied first.
5.
Please see the latest P30 Spec Update for synchronous burst operation with the TSOP package.
6.
Synchronous read mode is not supported with TTL level inputs.
7.
Applies only to subsequent synchronous reads.
Table 17: AC Read Specifications for 256/512-Mbit Densities (Sheet 1 of 3)
Num
Symbol
Parameter
Speed
Min
Max
VCC = 1.8 V – 2.0
85
-
VCC = 1.7 V – 2.0
88
-
Unit
Notes
Asynchronous Specifications
V
R1
tAVAV
Read cycle time
V
256/512-Mb TSOP
packages
R2
tAVQV
Address to output valid
-
85
VCC = 1.7 V – 2.0
-
88
-
95
V
256/512-Mb TSOP
packages
Datasheet
30
95
VCC = 1.8 V – 2.0
V
ns
ns
November 2007
Order Number: 306666-11
P30
Table 17: AC Read Specifications for 256/512-Mbit Densities (Sheet 2 of 3)
Num
Symbol
Parameter
Speed
Min
Max
VCC = 1.8 V – 2.0
-
85
VCC = 1.7 V – 2.0
-
88
-
95
-
25
V
R3
tELQV
CE# low to output valid
V
256/512-Mb TSOP
packages
Unit
Notes
ns
R4
tGLQV
OE# low to output valid
ns
R5
tPHQV
RST# high to output valid
-
150
ns
1
R6
tELQX
CE# low to output in low-Z
0
-
ns
1,3
R7
tGLQX
OE# low to output in low-Z
0
-
ns
1,2,3
R8
tEHQZ
CE# high to output in high-Z
-
24
ns
R9
tGHQZ
OE# high to output in high-Z
-
24
ns
R10
tOH
Output hold from first occurring address, CE#, or OE#
change
0
-
ns
R11
tEHEL
CE# pulse width high
20
-
ns
R12
tELTV
CE# low to WAIT valid
-
17
ns
R13
tEHTZ
CE# high to WAIT high-Z
-
20
ns
1,3
R15
tGLTV
OE# low to WAIT valid
-
17
ns
1
R16
tGLTX
OE# low to WAIT in low-Z
0
-
ns
R17
tGHTZ
OE# high to WAIT in high-Z
-
20
ns
10
-
ns
ns
1,2
1,3
1
1,3
Latching Specifications
R101
tAVVH
Address setup to ADV# high
R102
tELVH
CE# low to ADV# high
10
-
VCC = 1.8 V – 2.0
-
85
VCC = 1.7 V – 2.0
-
88
-
95
V
R103
tVLQV
ADV# low to output valid
V
256/512-Mb TSOP
packages
ns
R104
tVLVH
ADV# pulse width low
10
-
ns
R105
tVHVL
ADV# pulse width high
10
-
ns
R106
tVHAX
Address hold from ADV# high
9
-
ns
R108
tAPA
Page address access
-
25
ns
R111
tphvh
RST# high to ADV# high
30
-
ns
-
52
MHz
-
40
MHz
19.2
-
ns
25
-
ns
1
1,4
1
Clock Specifications
R200
fCLK
CLK frequency
R201
tCLK
CLK period
R202
tCH/CL
CLK high/low time
5
-
ns
R203
tFCLK/RCLK
CLK fall/rise time
-
3
ns
TSOP Package
TSOP Package
1,3,5,6
Synchronous Specifications(5,6)
November 2007
Order Number: 306666-11
Datasheet
31
P30
Table 17: AC Read Specifications for 256/512-Mbit Densities (Sheet 3 of 3)
Num
Symbol
Parameter
Speed
Min
Max
Unit
Notes
R301
tAVCH/L
Address setup to CLK
9
-
ns
R302
tVLCH/L
ADV# low setup to CLK
9
-
ns
R303
tELCH/L
CE# low setup to CLK
9
-
ns
R304
tCHQV / tCLQV
CLK to output valid
-
17
ns
R305
tCHQX
Output hold from CLK
3
-
ns
1,7
R306
tCHAX
Address hold from CLK
10
-
ns
1,4,7
R307
tCHTV
CLK to WAIT valid
-
17
ns
1,7
R311
tCHVL
CLK Valid to ADV# Setup
3
-
ns
1
R312
tCHTX
WAIT Hold from CLK
3
-
ns
1,7
1
Notes:
1.
See Figure 11, “AC Input/Output Reference Waveform” on page 28 for timing measurements and max
allowable input slew rate.
2.
OE# may be delayed by up to tELQV – tGLQV after CE#’s falling edge without impact to tELQV.
3.
Sampled, not 100% tested.
4.
Address hold in synchronous burst mode is tCHAX or tVHAX , whichever timing specification is satisfied first.
5.
Please see the latest P30 Spec Update for synchronous burst operation with the TSOP package.
6.
Synchronous read mode is not supported with TTL level inputs.
7.
Applies only to subsequent synchronous reads.
Table 18: AC Read Specification differences for 65nm
Num
Symbol
Parameter
Min
Max
Unit
Notes
100
-
ns
2
ns
2
ns
2
Asynchronous Specifications
R1
R2
R3
R103
tAVAV
tAVQV
tELQV
Read cycle time
Address to output valid
CE# low to output valid
TSOP
-
100
110
ns
2
-
100
ns
2
110
ns
2
-
100
ns
1,2
110
ns
2
TSOP
TSOP
tVLQV
ADV# low to output valid
110
TSOP
Notes:
1.
See Figure 11, “AC Input/Output Reference Waveform” on page 28 for timing measurements and
max allowable input slew rate.
2.
This is the recommended specification for all new designs supporting both 130nm and 65nm lithos, or for new designs
that will use the 65nm lithography.
Datasheet
32
November 2007
Order Number: 306666-11
P30
Figure 14: Asynchronous Single-Word Read (ADV# Low)
R1
R2
Address [A]
ADV#
R3
R8
CE# [E}
R4
R9
OE# [G]
R15
R17
WAIT [T]
R7
R6
Data [D/Q]
R5
RST# [P]
Note:
WAIT shown deasserted during asynchronous read mode (RCR[10]=0, Wait asserted low).
Figure 15: Asynchronous Single-Word Read (ADV# Latch)
R1
R2
Address [A]
A[1:0][A]
R101
R105
R106
ADV#
R3
R8
CE# [E}
R4
R9
OE# [G]
R15
R17
WAIT [T]
R7
R6
R10
Data [D/Q]
Note:
WAIT shown deasserted during asynchronous read mode (RCR[10]=0, Wait asserted low).
November 2007
Order Number: 306666-11
Datasheet
33
P30
Figure 16: Asynchronous Page-Mode Read Timing
R1
R2
A[Max:2] [A]
A[1:0]
R101
R105
R106
ADV#
R3
R8
CE# [E]
R4
R10
OE# [G]
R15
R17
WAIT [T]
R7
R9
R108
DATA [D/Q]
Note:
WAIT shown deasserted during asynchronous read mode (RCR[10]=0, Wait asserted low).
Figure 17: Synchronous Single-Word Array or Non-array Read Timing
R301
R306
CLK [C]
R2
Address [A]
R101
R106
R105
R104
ADV# [V]
R303
R102
R3
R8
CE# [E]
R7
R9
OE# [G]
R15
R307
R312 R17
WAIT [T]
R4
R304
R305
Data [D/Q]
1.
2.
WAIT is driven per OE# assertion during synchronous array or non-array read, and can be configured to assert either
during or one data cycle before valid data.
This diagram illustrates the case in which an n-word burst is initiated to the flash memory array and it is terminated by
CE# deassertion after the first word in the burst.
Datasheet
34
November 2007
Order Number: 306666-11
P30
Figure 18: Continuous Burst Read, Showing An Output Delay Timing
R301
R302
R306
R304
R304
R304
CLK [C]
R2
R101
Address [A]
R106
R105
ADV# [V]
R303
R102
R3
CE# [E]
OE# [G]
R15
R307
R312
WAIT [T]
R304
R4
R7
R305
R305
R305
R305
Data [D/Q]
Notes:
1.
WAIT is driven per OE# assertion during synchronous array or non-array read, and can be configured to assert either
during or one data cycle before valid data.
2.
At the end of Word Line; the delay incurred when a burst access crosses a 16-word boundary and the starting address is
not 4-word boundary aligned.
Figure 19: Synchronous Burst-Mode Four-Word Read Timing
y
R302
R301
R306
CLK [C]
R2
Address [A]
R101
A
R105
R102
R106
ADV# [V]
R303
R3
R8
CE# [E]
R9
OE# [G]
R15
R17
R307
WAIT [T]
R4
R7
Data [D/Q]
Note:
R304
R304
R305
Q0
R10
Q1
Q2
Q3
WAIT is driven per OE# assertion during synchronous array or non-array read. WAIT asserted during initial latency and
deasserted during valid data (RCR[10] = 0, Wait asserted low).
November 2007
Order Number: 306666-11
Datasheet
35
P30
7.4
AC Write Specifications
Table 19: AC Write Specifications
Num
Symbol
Parameter
Min
Max
Unit
Notes
150
-
ns
1,2,3
W1
tPHWL
RST# high recovery to WE# low
W2
tELWL
CE# setup to WE# low
0
-
ns
1,2,3
W3
tWLWH
WE# write pulse width low
50
-
ns
1,2,4
W4
tDVWH
Data setup to WE# high
50
-
ns
W5
tAVWH
Address setup to WE# high
50
-
ns
W6
tWHEH
CE# hold from WE# high
0
-
ns
W7
tWHDX
Data hold from WE# high
0
-
ns
W8
tWHAX
Address hold from WE# high
0
-
ns
W9
tWHWL
WE# pulse width high
20
-
ns
200
-
ns
0
-
ns
W10
tVPWH
VPP setup to WE# high
W11
tQVVL
VPP hold from Status read
W12
tQVBL
WP# hold from Status read
W13
tBHWH
WP# setup to WE# high
W14
tWHGL
WE# high to OE# low
W16
tWHQV
WE# high to read valid
0
-
ns
200
-
ns
1,2
1,2,5
1,2,3,7
1,2,3,7
0
-
ns
1,2,9
tAVQV + 35
-
ns
1,2,3,6,10
0
-
ns
1,2,3,6,8
Write to Asynchronous Read Specifications
W18
tWHAV
WE# high to Address valid
Write to Synchronous Read Specifications
W19
tWHCH/L
WE# high to Clock valid
19
-
ns
W20
tWHVH
WE# high to ADV# high
19
-
ns
1,2,3,6,10
Write Specifications with Clock Active
W21
tVHWL
ADV# high to WE# low
-
20
ns
W22
tCHWL
Clock high to WE# low
-
20
ns
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1,2,3,11
Write timing characteristics during erase suspend are the same as write-only operations.
A write operation can be terminated with either CE# or WE#.
Sampled, not 100% tested.
Write pulse width low (tWLWH or tELEH) is defined from CE# or WE# low (whichever occurs last) to CE# or WE# high
(whichever occurs first). Hence, tWLWH = tELEH = tWLEH = tELWH.
Write pulse width high (tWHWL or tEHEL) is defined from CE# or WE# high (whichever occurs first) to CE# or WE# low
(whichever occurs last). Hence, tWHWL = tEHEL = tWHEL = tEHWL).
tWHVH or tWHCH/L must be met when transitioning from a write cycle to a synchronous burst read.
VPP and WP# should be at a valid level until erase or program success is determined.
This specification is only applicable when transitioning from a write cycle to an asynchronous read. See spec W19 and
W20 for synchronous read.
When doing a Read Status operation following any command that alters the Status Register, W14 is 20 ns.
Add 10 ns if the write operation results in a RCR or block lock status change, for the subsequent read operation to reflect
this change.
These specs are required only when the device is in a synchronous mode and clock is active during address setup phase.
Datasheet
36
November 2007
Order Number: 306666-11
P30
Figure 20: Write-to-Write Timing
W5
W8
W5
W8
Address [A]
W2
W6
W2
W6
CE# [E}
W3
W9
W3
WE# [W]
OE# [G]
W4
W7
W4
W7
Data [D/Q]
W1
RST# [P]
Figure 21: Asynchronous Read-to-Write Timing
R1
R2
W5
W8
Address [A]
R3
R8
CE# [E}
R4
R9
OE# [G]
W2
W3
W6
WE# [W]
R15
R17
WAIT [T]
R7
W7
R6
Data [D/Q]
R10
Q
W4
D
R5
RST# [P]
Note:
WAIT deasserted during asynchronous read and during write. WAIT High-Z during write per OE# deasserted.
November 2007
Order Number: 306666-11
Datasheet
37
P30
Figure 22: Write-to-Asynchronous Read Timing
W5
W8
R1
Address [A]
ADV# [V]
W2
W6
R10
CE# [E}
W3
W18
WE# [W]
W14
OE# [G]
R15
R17
WAIT [T]
R4
W4
R2
R3
W7
Data [D/Q]
R8
R9
D
Q
W1
RST# [P]
Figure 23: Synchronous Read-to-Write Timing
Latency Count
R301
R302
R306
CLK [C]
R2
W5
R101
W18
Address [ A]
R105
R102
R106
R104
ADV# [ V]
R303
R11
R13
R3
W6
CE# [E]
R4
R8
OE# [G]
W 21
W 22
W15
W 21
W22
W2
W8
W3
W9
WE#
R16
R307
R312
WAIT [T]
R304
R7
Data [D/Q]
Note:
R305
Q
W7
D
D
WAIT shown deasserted and High-Z per OE# deassertion during write operation (RCR[10]=0, Wait asserted low). Clock is
ignored during write operation.
Datasheet
38
November 2007
Order Number: 306666-11
P30
Figure 24: Write-to-Synchronous Read Timing
R302
R301
R2
CLK
W5
W8
R306
Address [A]
R106
R104
ADV#
W6
R303
W2
R11
CE# [E}
W18
W19
W20
W3
WE# [W]
R4
OE# [G]
R15
R307
WAIT [T]
W7
R304
W4
R305
R304
R3
D
Data [D/Q]
Q
Q
W1
RST# [P]
Note:
WAIT shown deasserted and High-Z per OE# deassertion during write operation (RCR[10]=0, Wait asserted low).
7.5
Program and Erase Characteristics
Table 20:
Num
Symbol
V PPH
VPPL
Parameter
Min
Typ
Max
Min
Typ
Max
Units
Notes
µs
1
µs
1
Conventional Word Programming
W200
tPROG/W
Program
Time
Single word - 130nm
-
90
200
-
85
190
Single word - 65nm
-
125
150
-
125
150
Single cell
-
30
60
-
30
60
Buffered Programming
W200
tPROG/W
W251
tBUFF
W451
tBEFP/W
W452
tBEFP/Setup
Program
Time
Single word
-
90
200
-
85
190
32-word buffer
-
440
880
-
340
680
Buffered Enhanced Factory Programming
Program
Single word
BEFP Setup
n/a
n/a
n/a
-
10
-
n/a
n/a
n/a
5
-
-
µs
1,2
1
Erasing and Suspending
November 2007
Order Number: 306666-11
Datasheet
39
P30
Table 20:
Num
Symbol
W500
tERS/PB
W501
tERS/MB
W600
tSUSP/P
W601
tSUSP/E
W602
tERS/SUSP
Erase Time
Suspend
Latency
VPPH
VPPL
Parameter
Units
Min
Typ
Max
Min
Typ
Max
32-KByte Parameter
-
0.4
2.5
-
0.4
2.5
128-KByte Main
-
1.2
4.0
-
1.0
4.0
Program suspend
-
20
25
-
20
25
Erase suspend
-
20
25
-
20
25
Erase to Suspend
-
500
-
-
500
-
Notes
s
1
µs
1,3
Notes:
Typical values measured at TC = +25 °C and nominal voltages. Performance numbers are valid for all speed versions. Excludes system
1.
overhead. Sampled, but not 100% tested.
2.
Averaged over entire device.
3.
W602 is the typical time between an initial block erase or erase resume command and the a subsequent erase suspend
command. Violating the specification repeatedly during any particular block erase may cause erase failures.
Datasheet
40
November 2007
Order Number: 306666-11
P30
8.0
Power and Reset Specifications
8.1
Power-Up and Power-Down
Power supply sequencing is not required if VPP is connected to VCC or VCCQ. Otherwise
VCC and VCCQ should attain their minimum operating voltage before applying VPP.
Power supply transitions should only occur when RST# is low. This protects the device
from accidental programming or erasure during power transitions.
8.2
Reset Specifications
Asserting RST# during a system reset is important with automated program/erase
devices because systems typically expect to read from flash memory when coming out
of reset. If a CPU reset occurs without a flash memory reset, proper CPU initialization
may not occur. This is because the flash memory may be providing status information,
instead of array data as expected. Connect RST# to the same active low reset signal
used for CPU initialization.
Also, because the device is disabled when RST# is asserted, it ignores its control inputs
during power-up/down. Invalid bus conditions are masked, providing a level of memory
protection.
Table 21:
Num
Symbol
P1
tPLPH
P2
tPLRH
P3
Notes:
1.
2.
3.
4.
5.
6.
7.
tVCCPH
Parameter
RST# pulse width low
Min
Max
Unit
Notes
100
-
ns
1,2,3,4
RST# low to device reset during erase
-
25
RST# low to device reset during program
-
25
VCC Power valid to RST# de-assertion (high) 130nm
60
-
VCC Power valid to RST# de-assertion (high) 65nm
300
-
1,3,4,7
µs
1,3,4,7
1,4,5,6
1,4,5,6
These specifications are valid for all device versions (packages and speeds).
The device may reset if tPLPH is < tPLPH MIN, but this is not guaranteed.
Not applicable if RST# is tied to Vcc.
Sampled, but not 100% tested.
When RST# is tied to the VCC supply, device will not be ready until tVCCPH after VCC ≥ VCCMIN.
When RST# is tied to the VCCQ supply, device will not be ready until tVCCPH after VCC ≥ VCCMIN.
Reset completes within tPLPH if RST# is asserted while no erase or program operation is executing.
November 2007
Order Number: 306666-11
Datasheet
41
P30
Figure 25: Reset Operation Waveforms
P1
(A) Reset during
read mode
RST# [P]
VIH
VIL
P2
(B) Reset during
program or block erase
P1 ≤ P2
RST# [P]
RST# [P]
Abort
Complete
R5
VIH
VIL
P2
(C) Reset during
program or block erase
P1 ≥ P2
R5
Abort
Complete
R5
VIH
VIL
P3
(D) VCC Power-up to
RST# high
8.3
VCC
VCC
0V
Power Supply Decoupling
Flash memory devices require careful power supply de-coupling. Three basic power
supply current considerations are 1) standby current levels, 2) active current levels,
and 3) transient peaks produced when CE# and OE# are asserted and deasserted.
When the device is accessed, many internal conditions change. Circuits within the
device enable charge-pumps, and internal logic states change at high speed. All of
these internal activities produce transient signals. Transient current magnitudes depend
on the device outputs’ capacitive and inductive loading. Two-line control and correct
de-coupling capacitor selection suppress transient voltage peaks.
Because Numonyx Multi-Level Cell (MLC) flash memory devices draw their power from
VCC, VPP, and VCCQ, each power connection should have a 0.1 µF ceramic capacitor to
ground. High-frequency, inherently low-inductance capacitors should be placed as close
as possible to package leads.
Additionally, for every eight devices used in the system, a 4.7 µF electrolytic capacitor
should be placed between power and ground close to the devices. The bulk capacitor is
meant to overcome voltage droop caused by PCB trace inductance.
Datasheet
42
November 2007
Order Number: 306666-11
P30
9.0
Device Operations
This section provides an overview of device operations. The system CPU provides
control of all in-system read, write, and erase operations of the device via the system
bus. The on-chip Write State Machine (WSM) manages all block-erase and wordprogram algorithms.
Device commands are written to the Command User Interface (CUI) to control all flash
memory device operations. The CUI does not occupy an addressable memory location;
it is the mechanism through which the flash device is controlled.
9.1
Bus Operations
CE# low and RST# high enable device read operations. The device internally decodes
upper address inputs to determine the accessed block. ADV# low opens the internal
address latches. OE# low activates the outputs and gates selected data onto the I/O
bus.
In asynchronous mode, the address is latched when ADV# goes high or continuously
flows through if ADV# is held low. In synchronous mode, the address is latched by the
first of either the rising ADV# edge or the next valid CLK edge with ADV# low (WE#
and RST# must be VIH; CE# must be VIL).
Bus cycles to/from the P30 device conform to standard microprocessor bus operations.
Table 22 summarizes the bus operations and the logic levels that must be applied to
the device control signal inputs.
Table 22: Bus Operations Summary
Bus Operation
Read
RST#
CLK
ADV#
CE#
OE#
WE#
WAIT
DQ[15:0
]
Asynchronous
VIH
X
L
L
L
H
Deasserted
Output
Synchronous
VIH
Running
L
L
L
H
Driven
Output
Notes
Write
VIH
X
L
L
H
L
High-Z
Input
1
Output Disable
VIH
X
X
L
H
H
High-Z
High-Z
2
Standby
VIH
X
X
H
X
X
High-Z
High-Z
2
Reset
VIL
X
X
X
X
X
High-Z
High-Z
2,3
Notes:
1.
Refer to the Table 23, “Command Bus Cycles” on page 45 for valid DQ[15:0] during a write
operation.
2.
X = Don’t Care (H or L).
3.
RST# must be at VSS ± 0.2 V to meet the maximum specified power-down current.
9.1.1
Reads
To perform a read operation, RST# and WE# must be deasserted while CE# and OE#
are asserted. CE# is the device-select control. When asserted, it enables the flash
memory device. OE# is the data-output control. When asserted, the addressed flash
memory data is driven onto the I/O bus. See Section 10.0, “Read Operations” on
page 48 for details on the available read modes, and see Section 14.0, “Special Read
States” on page 69 for details regarding the available read states.
November 2007
Order Number: 306666-11
Datasheet
43
P30
9.1.2
Writes
To perform a write operation, both CE# and WE# are asserted while RST# and OE# are
deasserted. During a write operation, address and data are latched on the rising edge
of WE# or CE#, whichever occurs first. Table 23, “Command Bus Cycles” on page 45
shows the bus cycle sequence for each of the supported device commands, while
Table 24, “Command Codes and Definitions” on page 46 describes each command. See
Section 7.0, “AC Characteristics” on page 28 for signal-timing details.
Note:
9.1.3
Write operations with invalid VCC and/or VPP voltages can produce spurious results and should
not be attempted.
Output Disable
When OE# is deasserted, device outputs DQ[15:0] are disabled and placed in a highimpedance (High-Z) state, WAIT is also placed in High-Z.
9.1.4
Standby
When CE# is deasserted the device is deselected and placed in standby, substantially
reducing power consumption. In standby, the data outputs are placed in High-Z,
independent of the level placed on OE#. Standby current, ICCS, is the average current
measured over any 5 ms time interval, 5 μs after CE# is deasserted. During standby,
average current is measured over the same time interval 5 μs after CE# is deasserted.
When the device is deselected (while CE# is deasserted) during a program or erase
operation, it continues to consume active power until the program or erase operation is
completed.
9.1.5
Reset
As with any automated device, it is important to assert RST# when the system is reset.
When the system comes out of reset, the system processor attempts to read from the
flash memory if it is the system boot device. If a CPU reset occurs with no flash
memory reset, improper CPU initialization may occur because the flash memory may
be providing status information rather than array data. Flash memory devices from
Numonyx allow proper CPU initialization following a system reset through the use of the
RST# input. RST# should be controlled by the same low-true reset signal that resets
the system CPU.
After initial power-up or reset, the device defaults to asynchronous Read Array mode,
and the Status Register is set to 0x80. Asserting RST# de-energizes all internal
circuits, and places the output drivers in High-Z. When RST# is asserted, the device
shuts down the operation in progress, a process which takes a minimum amount of
time to complete. When RST# has been deasserted, the device is reset to
asynchronous Read Array state.
Note:
If RST# is asserted during a program or erase operation, the operation is terminated and the
memory contents at the aborted location (for a program) or block (for an erase) are no longer
valid, because the data may have been only partially written or erased.
When returning from a reset (RST# deasserted), a minimum wait is required before the
initial read access outputs valid data. Also, a minimum delay is required after a reset
before a write cycle can be initiated. After this wake-up interval passes, normal
operation is restored. See Section 7.0, “AC Characteristics” on page 28 for details
about signal-timing.
Datasheet
44
November 2007
Order Number: 306666-11
P30
9.2
Device Commands
Device operations are initiated by writing specific device commands to the Command
User Interface (CUI). See Table 23, “Command Bus Cycles” on page 45. Several
commands are used to modify array data including Word Program and Block Erase
commands. Writing either command to the CUI initiates a sequence of internally-timed
functions that culminate in the completion of the requested task. However, the
operation can be aborted by either asserting RST# or by issuing an appropriate
suspend command.
Table 23: Command Bus Cycles
Mode
Command
Read Array
Read
Program
Erase
Suspend
Block
Locking/
Unlocking
Protection
Configuration
Bus
Cycles
1
First Bus Cycle
Second Bus Cycle
Oper
Addr(1)
Data(2)
Oper
Addr(1)
Data (2)
Write
DnA
0xFF
-
-
-
Read Device Identifier
≥2
Write
DnA
0x90
Read
DBA + IA
ID
CFI Query
≥2
Write
DnA
0x98
Read
DBA + QA
QD
Read Status Register
2
Write
DnA
0x70
Read
DnA
SRD
Clear Status Register
1
Write
DnA
0x50
-
-
-
Word Program
2
Write
WA
0x40/
0x10
Write
WA
WD
Buffered Program(3)
>2
Write
WA
0xE8
Write
WA
N-1
Buffered Enhanced Factory
Program (BEFP)(4)
>2
Write
WA
0x80
Write
WA
0xD0
2
Write
BA
0x20
Write
BA
0xD0
Block Erase
Program/Erase Suspend
1
Write
DnA
0xB0
-
-
-
Program/Erase Resume
1
Write
DnA
0xD0
-
-
-
Lock Block
2
Write
BA
0x60
Write
BA
0x01
Unlock Block
2
Write
BA
0x60
Write
BA
0xD0
Lock-down Block
2
Write
BA
0x60
Write
BA
0x2F
Program Protection Register
2
Write
PRA
0xC0
Write
PRA
PD
Program Lock Register
2
Write
LRA
0xC0
Write
LRA
LRD
Program Read Configuration
Register
2
Write
RCD
0x60
Write
RCD
0x03
Notes:
1.
First command cycle address should be the same as the operation’s target address.
DBA = Device Base Address (NOTE: needed for dual-die 512 Mb device)
DnA = Address within the device.
IA = Identification code address offset.
QA = CFI Query address offset.
WA = Word address of memory location to be written.
BA = Address within the block.
PRA = Protection Register address.
LRA = Lock Register address.
RCD = Read Configuration Register data on QUAD+ A[15:0] or EASY BGA A[16:1].
2.
ID = Identifier data.
QD = Query data on DQ[15:0].
SRD = Status Register data.
WD = Word data.
N = Word count of data to be loaded into the write buffer.
PD = Protection Register data.
LRD = Lock Register data.
3.
The second cycle of the Buffered Program Command is the word count of the data to be loaded into the write buffer. This
is followed by up to 32 words of data.Then the confirm command (0xD0) is issued, triggering the array programming
operation.
4.
The confirm command (0xD0) is followed by the buffer data.
November 2007
Order Number: 306666-11
Datasheet
45
P30
9.3
Command Definitions
Valid device command codes and descriptions are shown in Table 24.
Table 24: Command Codes and Definitions (Sheet 1 of 2)
Mode
Code
0xFF
Read
Write
Write
Device Mode
Read Array
Places the device in Read Array mode. Array data is output on DQ[15:0].
0x70
Read Status
Register
Places the device in Read Status Register mode. The device enters this mode
after a program or erase command is issued. Status Register data is output
on DQ[7:0].
0x90
Read Device ID
or Configuration
Register
Places device in Read Device Identifier mode. Subsequent reads output
manufacturer/device codes, Configuration Register data, Block Lock status,
or Protection Register data on DQ[15:0].
0x98
Read Query
Places the device in Read Query mode. Subsequent reads output Common
Flash Interface information on DQ[7:0].
0x50
Clear Status
Register
The WSM can only set Status Register error bits. The Clear Status Register
command is used to clear the SR error bits.
0x40
Word Program
Setup
First cycle of a 2-cycle programming command; prepares the CUI for a write
operation. On the next write cycle, the address and data are latched and the
WSM executes the programming algorithm at the addressed location. During
program operations, the device responds only to Read Status Register and
Program Suspend commands. CE# or OE# must be toggled to update the
Status Register in asynchronous read. CE# or ADV# must be toggled to
update the Status Register Data for synchronous Non-array reads. The Read
Array command must be issued to read array data after programming has
finished.
0x10
Alternate Word
Program Setup
Equivalent to the Word Program Setup command, 0x40.
0xE8
Buffered Program
This command loads a variable number of words up to the buffer size of 32
words onto the program buffer.
0xD0
Buffered Program
Confirm
The confirm command is Issued after the data streaming for writing into the
buffer is done. This instructs the WSM to perform the Buffered Program
algorithm, writing the data from the buffer to the flash memory array.
0x80
BEFP Setup
First cycle of a 2-cycle command; initiates Buffered Enhanced Factory
Program mode (BEFP). The CUI then waits for the BEFP Confirm command,
0xD0, that initiates the BEFP algorithm. All other commands are ignored
when BEFP mode begins.
0xD0
BEFP Confirm
If the previous command was BEFP Setup (0x80), the CUI latches the
address and data, and prepares the device for BEFP mode.
Block Erase Setup
First cycle of a 2-cycle command; prepares the CUI for a block-erase
operation. The WSM performs the erase algorithm on the block addressed by
the Erase Confirm command. If the next command is not the Erase Confirm
(0xD0) command, the CUI sets Status Register bits SR[4] and SR[5], and
places the device in read status register mode.
Block Erase Confirm
If the first command was Block Erase Setup (0x20), the CUI latches the
address and data, and the WSM erases the addressed block. During blockerase operations, the device responds only to Read Status Register and Erase
Suspend commands. CE# or OE# must be toggled to update the Status
Register in asynchronous read. CE# or ADV# must be toggled to update the
Status Register Data for synchronous Non-array reads
0xB0
Program or Erase
Suspend
This command issued to any device address initiates a suspend of the
currently-executing program or block erase operation. The Status Register
indicates successful suspend operation by setting either SR[2] (program
suspended) or SR[6] (erase suspended), along with SR[7] (ready). The Write
State Machine remains in the suspend mode regardless of control signal
states (except for RST# asserted).
0xD0
Suspend Resume
This command issued to any device address resumes the suspended program
or block-erase operation.
0x20
Erase
0xD0
Suspend
Datasheet
46
Description
November 2007
Order Number: 306666-11
P30
Table 24: Command Codes and Definitions (Sheet 2 of 2)
Mode
Block Locking/
Unlocking
Protection
Code
Device Mode
0x60
Lock Block Setup
First cycle of a 2-cycle command; prepares the CUI for block lock
configuration changes. If the next command is not Block Lock (0x01), Block
Unlock (0xD0), or Block Lock-Down (0x2F), the CUI sets Status Register bits
SR[4] and SR[5], indicating a command sequence error.
0x01
Lock Block
If the previous command was Block Lock Setup (0x60), the addressed block
is locked.
0xD0
Unlock Block
If the previous command was Block Lock Setup (0x60), the addressed block
is unlocked. If the addressed block is in a lock-down state, the operation has
no effect.
0x2F
Lock-Down Block
If the previous command was Block Lock Setup (0x60), the addressed block
is locked down.
0xC0
Program Protection
Register Setup
First cycle of a 2-cycle command; prepares the device for a Protection
Register or Lock Register program operation. The second cycle latches the
register address and data, and starts the programming algorithm
0x60
Read Configuration
Register Setup
First cycle of a 2-cycle command; prepares the CUI for device read
configuration. If the Set Read Configuration Register command (0x03) is not
the next command, the CUI sets Status Register bits SR[4] and SR[5],
indicating a command sequence error.
0x03
Read Configuration
Register
If the previous command was Read Configuration Register Setup (0x60), the
CUI latches the address and writes A[15:0] to the Read Configuration
Register. Following a Configure Read Configuration Register command,
subsequent read operations access array data.
Configuration
November 2007
Order Number: 306666-11
Description
Datasheet
47
P30
10.0
Read Operations
The device supports two read modes: asynchronous page mode and synchronous burst
mode. Asynchronous page mode is the default read mode after device power-up or a
reset. The Read Configuration Register must be configured to enable synchronous burst
reads of the flash memory array (see Section 10.3, “Read Configuration Register” on
page 49).
The device can be in any of four read states: Read Array, Read Identifier, Read Status
or Read Query. Upon power-up, or after a reset, the device defaults to Read Array. To
change the read state, the appropriate read command must be written to the device
(see Section 9.2, “Device Commands” on page 45). See Section 14.0, “Special Read
States” on page 69 for details regarding Read Status, Read ID, and CFI Query modes.
The following sections describe read-mode operations in detail.
10.1
Asynchronous Page-Mode Read
Following a device power-up or reset, asynchronous page mode is the default read
mode and the device is set to Read Array. However, to perform array reads after any
other device operation (e.g. write operation), the Read Array command must be issued
in order to read from the flash memory array.
Note:
Asynchronous page-mode reads can only be performed when Read Configuration Register bit
RCR[15] is set (see Section 10.3, “Read Configuration Register” on page 49).
To perform an asynchronous page-mode read, an address is driven onto the Address
bus, and CE# and ADV# are asserted. WE# and RST# must already have been
deasserted. WAIT is deasserted during asynchronous page mode. ADV# can be driven
high to latch the address, or it must be held low throughout the read cycle. CLK is not
used for asynchronous page-mode reads, and is ignored. If only asynchronous reads
are to be performed, CLK should be tied to a valid VIH level, WAIT signal can be floated
and ADV# must be tied to ground. Array data is driven onto DQ[15:0] after an initial
access time tAVQV delay. (see Section 7.0, “AC Characteristics” on page 28).
In asynchronous page mode, four data words are “sensed” simultaneously from the flash
memory array and loaded into an internal page buffer. The buffer word corresponding
to the initial address on the Address bus is driven onto DQ[15:0] after the initial access
delay. The lowest two address bits determine which word of the 4-word page is output
from the data buffer at any given time.
10.2
Synchronous Burst-Mode Read
To perform a synchronous burst-read, an initial address is driven onto the Address bus, and
CE# and ADV# are asserted. WE# and RST# must already have been deasserted.
ADV# is asserted, and then deasserted to latch the address. Alternately, ADV# can
remain asserted throughout the burst access, in which case the address is latched on
the next valid CLK edge while ADV# is asserted.
During synchronous array and non-array read modes, the first word is output from the
data buffer on the next valid CLK edge after the initial access latency delay (see Section
10.3.2, “Latency Count” on page 50). Subsequent data is output on valid CLK edges
following a minimum delay. However, for a synchronous non-array read, the same word
of data will be output on successive clock edges until the burst length requirements are
satisfied. Refer to the following waveforms for more detailed information:
• Figure 17, “Synchronous Single-Word Array or Non-array Read Timing” on page 34
• Figure 18, “Continuous Burst Read, Showing An Output Delay Timing” on page 35
• Figure 19, “Synchronous Burst-Mode Four-Word Read Timing” on page 35
Datasheet
48
November 2007
Order Number: 306666-11
P30
10.3
Read Configuration Register
The Read Configuration Register (RCR) is used to select the read mode (synchronous or
asynchronous), and it defines the synchronous burst characteristics of the device. To
modify RCR settings, use the Configure Read Configuration Register command (see
Section 9.2, “Device Commands” on page 45).
RCR contents can be examined using the Read Device Identifier command, and then
reading from offset 0x05 (see Section 14.2, “Read Device Identifier” on page 70).
The RCR is shown in Table 25. The following sections describe each RCR bit.
Table 25: Read Configuration Register Description
Read Configuration Register (RCR)
Read
Mode
RES
Latency Count
WAIT
Polarity
Data
Hold
WAIT
Delay
Burst
Seq
CLK
Edge
RES
RES
Burst
Wrap
Burst Length
RM
R
LC[2:0]
WP
DH
WD
BS
CE
R
R
BW
BL[2:0]
15
14
10
9
8
7
6
5
4
3
Bit
13
15
Read Mode (RM)
14
Reserved (R)
13:11
10
9
8
7
6
5:4
3
2:0
Note:
12
11
Name
Latency Count (LC[2:0])
0
Reserved bits should be cleared (0)
010 =Code 2
011 =Code 3
100 =Code 4
101 =Code 5
110 =Code 6
111 =Code 7 (default)
(Other bit settings are reserved)
0 =WAIT signal is active low
1 =WAIT signal is active high (default)
Data Hold (DH)
0 =Data held for a 1-clock data cycle
1 =Data held for a 2-clock data cycle (default)
0 =WAIT deasserted with valid data
1 =WAIT deasserted one data cycle before valid data (default)
Burst Sequence (BS)
0 =Reserved
1 =Linear (default)
Clock Edge (CE)
0 = Falling edge
1 = Rising edge (default)
Reserved (R)
Reserved bits should be cleared (0)
Burst Wrap (BW)
0 =Wrap; Burst accesses wrap within burst length set by BL[2:0]
1 =No Wrap; Burst accesses do not wrap within burst length (default)
Burst Length (BL[2:0])
1
0 = Synchronous burst-mode read
1 = Asynchronous page-mode read (default)
Wait Polarity (WP)
Wait Delay (WD)
2
Description
001 =4-word burst
010 =8-word burst
011 =16-word burst
111 =Continuous-word burst (default)
(Other bit settings are reserved)
Latency Code 2, Data Hold for a 2-clock data cycle (DH = 1) WAIT must be deasserted with valid data (WD = 0).
Latency Code 2, Data Hold for a 2-cock data cycle (DH=1) WAIT deasserted one data cycle before valid data (WD = 1)
combination is not supported. Table 25, “Read Configuration Register Description” on page 49 is
shown using the QUAD+ package. For EASY BGA and TSOP packages, the table reference should be adjusted using
address bits A[16:1].
November 2007
Order Number: 306666-11
Datasheet
49
P30
10.3.1
Read Mode
The Read Mode (RM) bit selects synchronous burst-mode or asynchronous page-mode
operation for the device. When the RM bit is set, asynchronous page mode is selected
(default). When RM is cleared, synchronous burst mode is selected.
10.3.2
Latency Count
The Latency Count (LC) bits tell the device how many clock cycles must elapse from the
rising edge of ADV# (or from the first valid clock edge after ADV# is asserted) until the
first valid data word is to be driven onto DQ[15:0]. The input clock frequency is used to
determine this value and Figure 26 shows the data output latency for the different
settings of LC. The maximum Latency Count for P30 would be Code 4 based on the Max
Clock frequency specification of 52 mhz, and there will be zero WAIT States when
bursting within the word line. Please also refer to “End of Word Line (EOWL)
Considerations” on page 55 for more information on EOWL.
Refer to Table 26, “Latency Count (LC) and Frequency Support” on page 51 for Latency
Code Settings.
Datasheet
50
November 2007
Order Number: 306666-11
P30
Figure 26: First-Access Latency Count
CLK [C]
Address [A]
Valid
Address
ADV# [V]
Code 0 (Reserved)
Valid
Output
DQ15-0 [D/Q]
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Code 1
(Reserved
DQ15-0 [D/Q]
Code 2
DQ15-0 [D/Q]
Code 3
DQ15-0 [D/Q]
Code 4
DQ15-0 [D/Q]
Code 5
DQ15-0 [D/Q]
Code 6
DQ15-0 [D/Q]
Code 7
DQ15-0 [D/Q]
Valid
Output
Table 26: Latency Count (LC) and Frequency Support
Latency Count Settings
Note:
Frequency Support (MHz)
2
£ 27
3
£ 40
4
£ 52
Synchronous burst read operation is currently not supported for the TSOP package.
November 2007
Order Number: 306666-11
Datasheet
51
P30
Figure 27: Example Latency Count Setting using Code 3
0
1
2
3
tData
4
CLK
CE#
ADV#
A[MAX:0]
Address
Code 3
High-Z
D[15:0]
Data
R103
10.3.3
WAIT Polarity
The WAIT Polarity bit (WP), RCR[10] determines the asserted level (VOH or VOL ) of
WAIT. When WP is set, WAIT is asserted high (default). When WP is cleared, WAIT is
asserted low. WAIT changes state on valid clock edges during active bus cycles (CE#
asserted, OE# asserted, RST# deasserted).
10.3.3.1
WAIT Signal Function
The WAIT signal indicates data valid when the device is operating in synchronous mode
(RCR[15]=0). The WAIT signal is only “deasserted” when data is valid on the bus.
When the device is operating in synchronous non-array read mode, such as read
status, read ID, or read query. The WAIT signal is also “deasserted” when data is valid
on the bus.
WAIT behavior during synchronous non-array reads at the end of word line works
correctly only on the first data access.
When the device is operating in asynchronous page mode, asynchronous single word
read mode, and all write operations, WAIT is set to a deasserted state as determined
by RCR[10]. See Figure 15, “Asynchronous Single-Word Read (ADV# Latch)” on
page 33, and Figure 16, “Asynchronous Page-Mode Read Timing” on page 34.
Table 27: WAIT Functionality Table (Sheet 1 of 2)
Condition
WAIT
Notes
CE# = ‘1’, OE# = ‘X’ or CE# = ‘0’, OE# = ‘1’
High-Z
1
CE# =’0’, OE# = ‘0’
Active
1
Synchronous Array Reads
Active
1
Synchronous Non-Array Reads
Active
1
Datasheet
52
November 2007
Order Number: 306666-11
P30
Table 27: WAIT Functionality Table (Sheet 2 of 2)
Condition
WAIT
All Asynchronous Reads
Deasserted
All Writes
High-Z
Notes
1
1,2
Notes:
1.
Active: WAIT is asserted until data becomes valid, then deasserts
2.
When OE# = VIH during writes, WAIT = High-Z
10.3.4
Data Hold
For burst read operations, the Data Hold (DH) bit determines whether the data output
remains valid on DQ[15:0] for one or two clock cycles. This period of time is called the
“data cycle”. When DH is set, output data is held for two clocks (default). When DH is
cleared, output data is held for one clock (see Figure 28). The processor’s data setup
time and the flash memory’s clock-to-data output delay should be considered when
determining whether to hold output data for one or two clocks. A method for
determining the Data Hold configuration is shown below:
To set the device at one clock data hold for subsequent reads, the following condition
must be satisfied:
tCHQV (ns) + tDATA (ns) ≤ One CLK Period (ns)
tDATA = Data set up to Clock (defined by CPU)
For example, with a clock frequency of 40 MHz, the clock period is 25 ns. Assuming
tCHQV = 20 ns and tDATA = 4 ns. Applying these values to the formula above:
20 ns + 4 ns ≤ 25 ns
The equation is satisfied and data will be available at every clock period with data hold
setting at one clock. If tCHQV (ns) + tDATA (ns) > One CLK Period (ns), data hold setting of
2 clock periods must be used.
Figure 28: Data Hold Timing
CLK [C]
1 CLK
Data Hold
D[15:0] [Q]
2 CLK
Data Hold
D[15:0] [Q]
10.3.5
Valid
Output
Valid
Output
Valid
Output
Valid
Output
Valid
Output
WAIT Delay
The WAIT Delay (WD) bit controls the WAIT assertion-delay behavior during
synchronous burst reads. WAIT can be asserted either during or one data cycle before
valid data is output on DQ[15:0]. When WD is set, WAIT is deasserted one data cycle
before valid data (default). When WD is cleared, WAIT is deasserted during valid data.
November 2007
Order Number: 306666-11
Datasheet
53
P30
10.3.6
Burst Sequence
The Burst Sequence (BS) bit selects linear-burst sequence (default). Only linear-burst
sequence is supported. Table 28 shows the synchronous burst sequence for all burst
lengths, as well as the effect of the Burst Wrap (BW) setting.
Table 28: Burst Sequence Word Ordering
Burst Addressing Sequence (DEC)
Start
Addr.
(DEC)
Burst
Wrap
(RCR[3])
0
4-Word Burst
(BL[2:0] =
0b001)
8-Word Burst
(BL[2:0] = 0b010)
16-Word Burst
(BL[2:0] = 0b011)
Continuous Burst
(BL[2:0] = 0b111)
0
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2-3-4…14-15
0-1-2-3-4-5-6-…
1
0
1-2-3-0
1-2-3-4-5-6-7-0
1-2-3-4-5…15-0
1-2-3-4-5-6-7-…
2
0
2-3-0-1
2-3-4-5-6-7-0-1
2-3-4-5-6…15-0-1
2-3-4-5-6-7-8-…
3
0
3-0-1-2
3-4-5-6-7-0-1-2
3-4-5-6-7…15-0-1-2
3-4-5-6-7-8-9-…
4
0
4-5-6-7-0-1-2-3
4-5-6-7-8…15-0-1-2-3
4-5-6-7-8-9-10…
5
0
5-6-7-0-1-2-3-4
5-6-7-8-9…15-0-1-2-3-4
5-6-7-8-9-10-11…
6-7-8-9-10-11-12-…
7-8-9-10-11-12-13…
6
0
6-7-0-1-2-3-4-5
6-7-8-9-10…15-0-1-2-3-45
7
0
7-0-1-2-3-4-5-6
7-8-9-10…15-0-1-2-3-4-56
…
…
…
…
…
…
14
0
14-15-0-1-2…12-13
14-15-16-17-18-19-20-…
15
0
15-0-1-2-3…13-14
15-16-17-18-19-20-21-…
…
…
…
…
…
1
0-1-2-3
0-1-2-3-4-5-6-7
0-1-2-3-4…14-15
0-1-2-3-4-5-6-…
1
1
1-2-3-4
1-2-3-4-5-6-7-8
1-2-3-4-5…15-16
1-2-3-4-5-6-7-…
2
1
2-3-4-5
2-3-4-5-6-7-8-9
2-3-4-5-6…16-17
2-3-4-5-6-7-8-…
3
1
3-4-5-6
4
1
5
1
5-6-7-8-9-10-11-12
5-6-7-8-9…19-20
5-6-7-8-9-10-11…
6
1
6-7-8-9-10-11-12-13
6-7-8-9-10…20-21
6-7-8-9-10-11-12-…
7
1
7-8-9-10-11-12-1314
7-8-9-10-11…21-22
7-8-9-10-11-12-13…
…
…
3-4-5-6-7-8-9-10
3-4-5-6-7…17-18
3-4-5-6-7-8-9-…
4-5-6-7-8-9-10-11
4-5-6-7-8…18-19
4-5-6-7-8-9-10…
…
…
…
14
1
14-15-16-17-18…28-29
14-15-16-17-18-19-20-…
15
1
15-16-17-18-19…29-30
15-16-17-18-19-20-21-…
10.3.7
…
…
0
Clock Edge
The Clock Edge (CE) bit selects either a rising (default) or falling clock edge for CLK.
This clock edge is used at the start of a burst cycle, to output synchronous data, and to
assert/deassert WAIT.
Datasheet
54
November 2007
Order Number: 306666-11
P30
10.3.8
Burst Wrap
The Burst Wrap (BW) bit determines whether 4-word, 8-word, or 16-word burst length
accesses wrap within the selected word-length boundaries or cross word-length
boundaries. When BW is set, burst wrapping does not occur (default). When BW is
cleared, burst wrapping occurs.
When performing synchronous burst reads with BW set (no wrap), an output delay may
occur when the burst sequence crosses its first device-row (16-word) boundary. If the
burst sequence’s start address is 4-word aligned, then no delay occurs. If the start
address is at the end of a 4-word boundary, the worst case output delay is one clock
cycle less than the first access Latency Count. This delay can take place only once, and
doesn’t occur if the burst sequence does not cross a device-row boundary. WAIT
informs the system of this delay when it occurs.
10.3.9
Burst Length
The Burst Length bit (BL[2:0]) selects the linear burst length for all synchronous burst
reads of the flash memory array. The burst lengths are 4-word, 8-word, 16-word, and
continuous word.
Continuous-burst accesses are linear only, and do not wrap within any word length
boundaries (see Table 28, “Burst Sequence Word Ordering” on page 54). When a burst
cycle begins, the device outputs synchronous burst data until it reaches the end of the
“burstable” address space.
10.3.10
End of Word Line (EOWL) Considerations
When performing synchronous burst reads with BW set (no wrap) and DH reset (1 clock
cycle), an output “delay” requiring additions clock Wait States may occur when the
burst sequence crosses its first device-row (16-word) boundary. The delay would take
place only once, and will not occur if the burst sequence does not cross a device-row
boundary. The WAIT signal informs the system of this delay when it occurs. If the burst
sequence’s start address is 4-word aligned (i.e. 0x00h, 0x04h, 0x08h, 0x0Ch) then no
delay occurs. If the start address is at the end of a 4-word boundary (i.e. 0x03h,
0x07h, 0x0Bh, 0x0Fh), the worst case delay (number of Wait States required) will be
one clock cycle less than the first access Latency Count (LC-1) when crossing the first
device-row boundary (i.e. 0x0Fh to 0x10h). Other address misalignments may require
wait states depending upon the LC setting and the starting address alignment. For
example, an LC setting of 3 with a starting address of 0xFD requires 0 wait states, but
the same LC setting of 3 with a starting address of 0xFE would require 1 wait state
when crossing the first device row boundary.
November 2007
Order Number: 306666-11
Datasheet
55
P30
11.0
Programming Operations
The device supports three programming methods: Word Programming (40h/10h),
Buffered Programming (E8h, D0h), and Buffered Enhanced Factory Programming (80h,
D0h). See
Section 9.0, “Device Operations” on page 43 for details on the various programming
commands issued to the device. The following sections describe device programming in
detail.
Successful programming requires the addressed block to be unlocked. If the block is
locked down, WP# must be deasserted and the block must be unlocked before
attempting to program the block. Attempting to program a locked block causes a
program error (SR[4] and SR[1] set) and termination of the operation. See Section
13.0, “Security Modes” on page 64 for details on locking and unlocking blocks.
The Product Name is segmented into multiple 8-Mbit Programming Regions. See
Section 4.4, “Memory Maps” on page 22 for complete addressing. Execute in Place
(XIP) applications must partition the memory such that code and data are in separate
programming regions. XIP is executing code directly from flash memory. Each
Programming Region should contain only code or data but not both. The following
terms define the difference between code and data. System designs must use these
definitions when partitioning their code and data for the P30 device.
• Code: Execution code ran out of the flash device on a continuous basis in the
system.
• Data: Information periodically programmed into the flash device and read back
(e.g. execution code shadowed and executed in RAM, pictures, log files, etc.).
11.1
Word Programming
Word programming operations are initiated by writing the Word Program Setup
command to the device (see Section 9.0, “Device Operations” on page 43). This is
followed by a second write to the device with the address and data to be programmed.
The device outputs Status Register data when read. See Figure 38, “Word Program
Flowchart” on page 79. VPP must be above VPPLK, and within the specified VPPL min/
max values.
During programming, the Write State Machine (WSM) executes a sequence of
internally-timed events that program the desired data bits at the addressed location,
and verifies that the bits are sufficiently programmed. Programming the flash memory
array changes “ones” to “zeros”. Memory array bits that are zeros can be changed to
ones only by erasing the block (see Section 12.0, “Erase Operations” on page 62).
The Status Register can be examined for programming progress and errors by reading
at any address. The device remains in the Read Status Register state until another
command is written to the device.
Status Register bit SR[7] indicates the programming status while the sequence
executes. Commands that can be issued to the device during programming are
Program Suspend, Read Status Register, Read Device Identifier, CFI Query, and Read
Array (this returns unknown data).
When programming has finished, Status Register bit SR[4] (when set) indicates a
programming failure. If SR[3] is set, the WSM could not perform the word
programming operation because VPP was outside of its acceptable limits. If SR[1] is set,
the word programming operation attempted to program a locked block, causing the
operation to abort.
Datasheet
56
November 2007
Order Number: 306666-11
P30
Before issuing a new command, the Status Register contents should be examined and
then cleared using the Clear Status Register command. Any valid command can follow,
when word programming has completed.
11.1.1
Factory Word Programming
Factory word programming is similar to word programming in that it uses the same
commands and programming algorithms. However, factory word programming
enhances the programming performance with VPP = VPPH. This can enable faster
programming times during OEM manufacturing processes. Factory word programming
is not intended for extended use. See Section 5.2, “Operating Conditions” on page 25
for limitations when VPP = VPPH.
Note:
11.2
When VPP = VPPL, the device draws programming current from the VCC supply. If VPP is driven
by a logic signal, VPPL must remain above VPPL MIN to program the device. When VPP = VPPH,
the device draws programming current from the VPP supply. Figure 29, “Example VPP Supply
Connections” on page 61 shows examples of device power supply configurations.
Buffered Programming
The device features a 32-word buffer to enable optimum programming performance.
For Buffered Programming, data is first written to an on-chip write buffer. Then the
buffer data is programmed into the flash memory array in buffer-size increments. This
can improve system programming performance significantly over non-buffered
programming.
When the Buffered Programming Setup command is issued (see Section 9.2, “Device
Commands” on page 45), Status Register information is updated and reflects the
availability of the buffer. SR[7] indicates buffer availability: if set, the buffer is
available; if cleared, the buffer is not available. To retry, issue the Buffered
Programming Setup command again, and re-check SR[7]. When SR[7] is set, the
buffer is ready for loading. (see Figure 40, “Buffer Program Flowchart” on page 81).
On the next write, a word count is written to the device at the buffer address. This tells
the device how many data words will be written to the buffer, up to the maximum size
of the buffer.
On the next write, a device start address is given along with the first data to be written
to the flash memory array. Subsequent writes provide additional device addresses and
data. All data addresses must lie within the start address plus the word count.
Optimum programming performance and lower power usage are obtained by aligning
the starting address at the beginning of a 32-word boundary (A[4:0] = 0x00). Crossing
a 32-word boundary during programming will double the total programming time.
After the last data is written to the buffer, the Buffered Programming Confirm command
must be issued to the original block address. The WSM begins to program buffer
contents to the flash memory array. If a command other than the Buffered
Programming Confirm command is written to the device, a command sequence error
occurs and Status Register bits SR[7,5,4] are set. If an error occurs while writing to the
array, the device stops programming, and Status Register bits SR[7,4] are set,
indicating a programming failure.
When Buffered Programming has completed, additional buffer writes can be initiated by
issuing another Buffered Programming Setup command and repeating the buffered
program sequence. Buffered programming may be performed with VPP = VPPL or VPPH
(see Section 5.2, “Operating Conditions” on page 25 for limitations when operating the
device with VPP = VPPH).
November 2007
Order Number: 306666-11
Datasheet
57
P30
If an attempt is made to program past an erase-block boundary using the Buffered
Program command, the device aborts the operation. This generates a command
sequence error, and Status Register bits SR[5,4] are set.
If Buffered programming is attempted while VPP is below VPPLK, Status Register bits
SR[4,3] are set. If any errors are detected that have set Status Register bits, the
Status Register should be cleared using the Clear Status Register command.
11.3
Buffered Enhanced Factory Programming
Buffered Enhanced Factory Programing (BEFP) speeds up Multi-Level Cell (MLC) flash
programming. The enhanced programming algorithm used in BEFP eliminates
traditional programming elements that drive up overhead in device programmer
systems.
BEFP consists of three phases: Setup, Program/Verify, and Exit (see Figure 41, “BEFP
Flowchart” on page 82). It uses a write buffer to spread MLC program performance
across 32 data words. Verification occurs in the same phase as programming to
accurately program the flash memory cell to the correct bit state.
A single two-cycle command sequence programs the entire block of data. This
enhancement eliminates three write cycles per buffer: two commands and the word
count for each set of 32 data words. Host programmer bus cycles fill the device’s write
buffer followed by a status check. SR[0] indicates when data from the buffer has been
programmed into sequential flash memory array locations.
Following the buffer-to-flash array programming sequence, the Write State Machine
(WSM) increments internal addressing to automatically select the next 32-word array
boundary. This aspect of BEFP saves host programming equipment the address-bus
setup overhead.
With adequate continuity testing, programming equipment can rely on the WSM’s
internal verification to ensure that the device has programmed properly. This eliminates
the external post-program verification and its associated overhead.
11.3.1
BEFP Requirements and Considerations
Table 29: BEFP Requirements
Parameter/Issue
Requirement
Notes
Case Temperature
TC = 25 °C ± 5 °C
VCC
Within operating range
VPP
Driven to VPPH
Setup and Confirm
Target block unlocked before issuing the BEFP Setup and Confirm commands
Programming
The first-word address (WA0) of the block to be programmed must be held constant
from the setup phase through all data streaming into the target block, until transition
to the exit phase is desired
Buffer Alignment
WA0 must align with the start of an array buffer boundary
Note:
1.
1
Word buffer boundaries in the array are determined by A[4:0] (0x00 through 0x1F). The alignment start point is A[4:0] =
0x00.
Datasheet
58
November 2007
Order Number: 306666-11
P30
Table 30: BEFP Considerations
Parameter/Issue
Requirement
Notes
Cycling
For optimum performance, cycling must be limited below 100 erase cycles per block.
1
Programming blocks
BEFP programs one block at a time; all buffer data must fall within a single block
2
Suspend
BEFP cannot be suspended
Programming the flash
memory array
Programming to the flash memory array can occur only when the buffer is full.
Note:
1.
2.
3.
3
Some degradation in performance may occur if this limit is exceeded, but the internal algorithm continues to work
properly.
If the internal address counter increments beyond the block's maximum address, addressing wraps around to the
beginning of the block.
If the number of words is less than 32, remaining locations must be filled with 0xFFFF.
11.3.2
BEFP Setup Phase
After receiving the BEFP Setup and Confirm command sequence, Status Register bit
SR[7] (Ready) is cleared, indicating that the WSM is busy with BEFP algorithm startup.
A delay before checking SR[7] is required to allow the WSM enough time to perform all
of its setups and checks (Block-Lock status, VPP level, etc.). If an error is detected,
SR[4] is set and BEFP operation terminates. If the block was found to be locked, SR[1]
is also set. SR[3] is set if the error occurred due to an incorrect VPP level.
Note:
Reading from the device after the BEFP Setup and Confirm command sequence outputs
Status Register data. Do not issue the Read Status Register command; it will be interpreted
as data to be loaded into the buffer.
11.3.3
BEFP Program/Verify Phase
After the BEFP Setup Phase has completed, the host programming system must check
SR[7,0] to determine the availability of the write buffer for data streaming. SR[7]
cleared indicates the device is busy and the BEFP program/verify phase is activated.
SR[0] indicates the write buffer is available.
Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer
data programming to the array. For BEFP, the count value for buffer loading is always
the maximum buffer size of 32 words. During the buffer-loading sequence, data is
stored to sequential buffer locations starting at address 0x00. Programming of the
buffer contents to the flash memory array starts as soon as the buffer is full. If the
number of words is less than 32, the remaining buffer locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an
address outside of the current block's range during a buffer-fill sequence
causes the algorithm to exit immediately. Any data previously loaded into the
buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the BEFP
algorithm will be aborted and the program fails and (SR[4]) flag will be set.
Data words from the write buffer are directed to sequential memory locations in the
flash memory array; programming continues from where the previous buffer sequence
ended. The host programming system must poll SR[0] to determine when the buffer
program sequence completes. SR[0] cleared indicates that all buffer data has been
transferred to the flash array; SR[0] set indicates that the buffer is not available yet for
the next fill cycle. The host system may check full status for errors at any time, but it is
November 2007
Order Number: 306666-11
Datasheet
59
P30
only necessary on a block basis after BEFP exit. After the buffer fill cycle, no write
cycles should be issued to the device until SR[0] = 0 and the device is ready for the
next buffer fill.
Note:
Any spurious writes are ignored after a buffer fill operation and when internal program is
proceeding.
The host programming system continues the BEFP algorithm by providing the next
group of data words to be written to the buffer. Alternatively, it can terminate this
phase by changing the block address to one outside of the current block’s range.
The Program/Verify phase concludes when the programmer writes to a different block
address; data supplied must be 0xFFFF. Upon Program/Verify phase completion, the
device enters the BEFP Exit phase.
11.3.4
BEFP Exit Phase
When SR[7] is set, the device has returned to normal operating conditions. A full status
check should be performed at this time to ensure the entire block programmed
successfully. When exiting the BEFP algorithm with a block address change, the read
mode will not change. After BEFP exit, any valid command can be issued to the device.
11.4
Program Suspend
Issuing the Program Suspend command while programming suspends the
programming operation. This allows data to be accessed from the device other than the
one being programmed. The Program Suspend command can be issued to any device
address. A program operation can be suspended to perform reads only. Additionally, a
program operation that is running during an erase suspend can be suspended to
perform a read operation (see Figure 39, “Program Suspend/Resume Flowchart” on
page 80).
When a programming operation is executing, issuing the Program Suspend command
requests the WSM to suspend the programming algorithm at predetermined points. The
device continues to output Status Register data after the Program Suspend command is
issued. Programming is suspended when Status Register bits SR[7,2] are set. Suspend
latency is specified in Section 7.5, “Program and Erase Characteristics” on page 39.
To read data from the device, the Read Array command must be issued. Read Array,
Read Status Register, Read Device Identifier, CFI Query, and Program Resume are valid
commands during a program suspend.
During a program suspend, deasserting CE# places the device in standby, reducing
active current. VPP must remain at its programming level, and WP# must remain
unchanged while in program suspend. If RST# is asserted, the device is reset.
11.5
Program Resume
The Resume command instructs the device to continue programming, and
automatically clears Status Register bits SR[7,2]. This command can be written to any
address. If error bits are set, the Status Register should be cleared before issuing the
next instruction. RST# must remain deasserted (see Figure 39, “Program Suspend/
Resume Flowchart” on page 80).
Datasheet
60
November 2007
Order Number: 306666-11
P30
11.6
Program Protection
When VPP = VIL, absolute hardware write protection is provided for all device blocks. If
VPP is at or below VPPLK, programming operations halt and SR[3] is set indicating a VPPlevel error. Block lock registers are not affected by the voltage level on VPP; they may
still be programmed and read, even if VPP is less than VPPLK.
Figure 29: Example VPP Supply Connections
VCC
VPP
VCC
VPP
VPP=VPPH
VCC
VPP
• Low Voltage and Factory Programming
November 2007
Order Number: 306666-11
PROT #
VCC
VPP
≤ 10K Ω
• Factory Programming with VPP = VPPH
• Complete write/Erase Protection when VPP ≤ VPPLK
VCC
VCC
• Low-voltage Programming only
• Logic Control of Device Protection
VCC
VCC
VPP
• Low Voltage Programming Only
• Full Device Protection Unavailable
Datasheet
61
P30
12.0
Erase Operations
Flash erasing is performed on a block basis. An entire block is erased each time an
erase command sequence is issued, and only one block is erased at a time. When a
block is erased, all bits within that block read as logical ones. The following sections
describe block erase operations in detail.
12.1
Block Erase
Block erase operations are initiated by writing the Block Erase Setup command to the address of the block to
be erased (see Section 9.2, “Device Commands” on page 45). Next, the Block Erase Confirm
command is written to the address of the block to be erased. If the device is placed in standby (CE#
deasserted) during an erase operation, the device completes the erase operation before
entering standby.VPP must be above VPPLK and the block must be unlocked (see Figure 42, “Block
Erase Flowchart” on page 83).
During a block erase, the Write State Machine (WSM) executes a sequence of
internally-timed events that conditions, erases, and verifies all bits within the block.
Erasing the flash memory array changes “zeros” to “ones”. Memory array bits that are
ones can be changed to zeros only by programming the block (see Section 11.0,
“Programming Operations” on page 56).
The Status Register can be examined for block erase progress and errors by reading
any address. The device remains in the Read Status Register state until another
command is written. SR[0] indicates whether the addressed block is erasing. Status
Register bit SR[7] is set upon erase completion.
Status Register bit SR[7] indicates block erase status while the sequence executes.
When the erase operation has finished, Status Register bit SR[5] indicates an erase
failure if set. SR[3] set would indicate that the WSM could not perform the erase
operation because VPP was outside of its acceptable limits. SR[1] set indicates that the
erase operation attempted to erase a locked block, causing the operation to abort.
Before issuing a new command, the Status Register contents should be examined and
then cleared using the Clear Status Register command. Any valid command can follow
once the block erase operation has completed.
12.2
Erase Suspend
Issuing the Erase Suspend command while erasing suspends the block erase operation.
This allows data to be accessed from memory locations other than the one being
erased. The Erase Suspend command can be issued to any device address. A block
erase operation can be suspended to perform a word or buffer program operation, or a
read operation within any block except the block that is erase suspended (see
Figure 39, “Program Suspend/Resume Flowchart” on page 80).
When a block erase operation is executing, issuing the Erase Suspend command
requests the WSM to suspend the erase algorithm at predetermined points. The device
continues to output Status Register data after the Erase Suspend command is issued.
Block erase is suspended when Status Register bits SR[7,6] are set. Suspend latency is
specified in Section 7.5, “Program and Erase Characteristics” on page 39.
To read data from the device (other than an erase-suspended block), the Read Array
command must be issued. During Erase Suspend, a Program command can be issued
to any block other than the erase-suspended block. Block erase cannot resume until
program operations initiated during erase suspend complete. Read Array, Read Status
Register, Read Device Identifier, CFI Query, and Erase Resume are valid commands
Datasheet
62
November 2007
Order Number: 306666-11
P30
during Erase Suspend. Additionally, Clear Status Register, Program, Program Suspend,
Block Lock, Block Unlock, and Block Lock-Down are valid commands during Erase
Suspend.
During an erase suspend, deasserting CE# places the device in standby, reducing
active current. VPP must remain at a valid level, and WP# must remain unchanged
while in erase suspend. If RST# is asserted, the device is reset.
12.3
Erase Resume
The Erase Resume command instructs the device to continue erasing, and
automatically clears status register bits SR[7,6]. This command can be written to any
address. If status register error bits are set, the Status Register should be cleared
before issuing the next instruction. RST# must remain deasserted (see Figure 39,
“Program Suspend/Resume Flowchart” on page 80).
12.4
Erase Protection
When VPP = VIL, absolute hardware erase protection is provided for all device blocks. If
VPP is below VPPLK, erase operations halt and SR[3] is set indicating a VPP-level error.
November 2007
Order Number: 306666-11
Datasheet
63
P30
13.0
Security Modes
The device features security modes used to protect the information stored in the flash
memory array. The following sections describe each security mode in detail.
13.1
Block Locking
Individual instant block locking is used to protect user code and/or data within the flash
memory array. All blocks power up in a locked state to protect array data from being
altered during power transitions. Any block can be locked or unlocked with no latency.
Locked blocks cannot be programmed or erased; they can only be read.
Software-controlled security is implemented using the Block Lock and Block Unlock
commands. Hardware-controlled security can be implemented using the Block LockDown command along with asserting WP#. Also, VPP data security can be used to
inhibit program and erase operations (see Section 11.6, “Program Protection” on
page 61 and Section 12.4, “Erase Protection” on page 63).
The P30 device also offers four pre-defined areas in the main array that can be
configured as One-Time Programmable (OTP) for the highest level of security. These
include the four 32 KB parameter blocks together as one and the three adjacent 128 KB
main blocks. This is available for top or bottom parameter devices.
13.1.1
Lock Block
To lock a block, issue the Lock Block Setup command. The next command must be the Lock Block command
issued to the desired block’s address (see Section 9.2, “Device Commands” on page 45 and
Figure 44, “Block Lock Operations Flowchart” on page 85). If the Set Read Configuration
Register command is issued after the Block Lock Setup command, the device
configures the RCR instead.
Block lock and unlock operations are not affected by the voltage level on VPP. The block
lock bits may be modified and/or read even if VPP is at or below VPPLK.
13.1.2
Unlock Block
The Unlock Block command is used to unlock blocks (see Section 9.2, “Device
Commands” on page 45). Unlocked blocks can be read, programmed, and erased.
Unlocked blocks return to a locked state when the device is reset or powered down. If a
block is in a lock-down state, WP# must be deasserted before it can be unlocked (see
Figure 30, “Block Locking State Diagram” on page 65).
13.1.3
Lock-Down Block
A locked or unlocked block can be locked-down by writing the Lock-Down Block
command sequence (see Section 9.2, “Device Commands” on page 45). Blocks in a
lock-down state cannot be programmed or erased; they can only be read. However,
unlike locked blocks, their locked state cannot be changed by software commands
alone. A locked-down block can only be unlocked by issuing the Unlock Block command
with WP# deasserted. To return an unlocked block to locked-down state, a Lock-Down
command must be issued prior to changing WP# to VIL. Locked-down blocks revert to
the locked state upon reset or power up the device (see Figure 30, “Block Locking State
Diagram” on page 65).
Datasheet
64
November 2007
Order Number: 306666-11
P30
13.1.4
Block Lock Status
The Read Device Identifier command is used to determine a block’s lock status (see
Section 14.2, “Read Device Identifier” on page 70). Data bits DQ[1:0] display the
addressed block’s lock status; DQ0 is the addressed block’s lock bit, while DQ1 is the
addressed block’s lock-down bit.
Figure 30: Block Locking State Diagram
Power-Up/Reset
Locked
[X01]
LockedDown 4,5
[011]
Hardware
Locked 5
[011]
WP# Hardware Control
Unlocked
[X00]
Software
Locked
[111]
Unlocked
[110]
Software Block Lock (0x60/0x01) or Software Block Unlock (0x60/0xD0)
Software Block Lock-Down (0x60/0x2F)
W P# hardware control
Notes:
13.1.5
1. [a,b,c] represents [WP#, DQ1, DQ0]. X = Don’t Care.
2. DQ1 indicates Block Lock-Down status. DQ1 = ‘0’, Lock-Down has not been issued
to this block. DQ1 = ‘1’, Lock-Down has been issued to this block.
3. DQ0 indicates block lock status. DQ0 = ‘0’, block is unlocked. DQ0 = ‘1’, block is
locked.
4. Locked-down = Hardware + Software locked.
5. [011] states should be tracked by system software to determine difference between
Hardware Locked and Locked-Down states.
Block Locking During Suspend
Block lock and unlock changes can be performed during an erase suspend. To change
block locking during an erase operation, first issue the Erase Suspend command.
Monitor the Status Register until SR[7] and SR[6] are set, indicating the device is
suspended and ready to accept another command.
Next, write the desired lock command sequence to a block, which changes the lock
state of that block. After completing block lock or unlock operations, resume the erase
operation using the Erase Resume command.
Note:
A Lock Block Setup command followed by any command other than Lock Block, Unlock Block,
or Lock-Down Block produces a command sequence error and set Status Register bits SR[4]
and SR[5]. If a command sequence error occurs during an erase suspend, SR[4] and SR[5]
remains set, even after the erase operation is resumed. Unless the Status Register is cleared
using the Clear Status Register command before resuming the erase operation, possible erase
errors may be masked by the command sequence error.
November 2007
Order Number: 306666-11
Datasheet
65
P30
If a block is locked or locked-down during an erase suspend of the same block, the lock
status bits change immediately. However, the erase operation completes when it is
resumed. Block lock operations cannot occur during a program suspend. See Appendix
A, “Write State Machine” on page 72, which shows valid commands during an erase
suspend.
13.2
Selectable One-Time Programmable Blocks
Any of four pre-defined areas from the main array (the four 32-KB parameter blocks
together as one and three adjacent 128 KB main blocks) can be configured as OTP so
further program and erase operations are not allowed. This option is available for top or
bottom parameter devices.
Table 31: Selectable OTP Block Mapping
Density
256-Mbit
128-Mbit
64-Mbit
Top Parameter Configuration
Bottom Parameter Configuration
blocks 258:255 (parameters)
blocks 3:0 (parameters)
block 254 (main)
block 4 (main)
block 253 (main)
block 5 (main)
block 252 (main)
block 6 (main)
blocks 130:127 (parameters)
blocks 3:0 (parameters)
block 126 (main)
block 4 (main)
block 125 (main)
block 5 (main)
block 124 (main)
block 6 (main)
blocks 66:63 (parameters)
blocks 3:0 (parameters)
block 62 (main)
block 4 (main)
block 61 (main)
block 5 (main)
block 60 (main)
block 6 (main)
Notes:
1.
The 512-Mbit devices will have multiple die and selectable OTP areas depending on the placement of the parameter
blocks.
2.
When programming the OTP bits for a Top Parameter Device, the following upper address bits must also be driven
properly: A[Max:17] driven high (VIH) for TSOP and Easy BGA packages, and A[Max:16] driven high (VIH) for QUAD+
SCSP.
Note:
13.3
Please see your local Numonyx representative for details about the Selectable OTP
implementation.
Protection Registers
The device contains 17 Protection Registers (PRs) that can be used to implement
system security measures and/or device identification. Each Protection Register can be
individually locked.
The first 128-bit Protection Register is comprised of two 64-bit (8-word) segments. The
lower 64-bit segment is pre-programmed at the Numonyx factory with a unique 64-bit
number. The other 64-bit segment, as well as the other sixteen 128-bit Protection
Registers, are blank. Users can program these registers as needed. When programmed,
users can then lock the Protection Register(s) to prevent additional bit programming
(see Figure 31, “Protection Register Map” on page 67).
Datasheet
66
November 2007
Order Number: 306666-11
P30
The user-programmable Protection Registers contain one-time programmable (OTP)
bits; when programmed, register bits cannot be erased. Each Protection Register can
be accessed multiple times to program individual bits, as long as the register remains
unlocked.
Each Protection Register has an associated Lock Register bit. When a Lock Register bit
is programmed, the associated Protection Register can only be read; it can no longer be
programmed. Additionally, because the Lock Register bits themselves are OTP, when
programmed, Lock Register bits cannot be erased. Therefore, when a Protection
Register is locked, it cannot be unlocked.
.
Figure 31: Protection Register Map
0x109
128-bit Protection Register 16
(User-Programmable)
0x102
0x91
128-bit Protection Register 1
(User-Programmable)
0x8A
Lock Register 1
0x89
0x88
0x85
0x84
0x81
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
1
0
64-bit Segment
(User-Programmable)
128-Bit Protection Register 0
64-bit Segment
(Factory-Programmed)
Lock Register 0
0x80
13.3.1
15 14 13 12 11 10 9
8
7
6
5
4
3
2
Reading the Protection Registers
The Protection Registers can be read from any address. To read the Protection Register,
first issue the Read Device Identifier command at any address to place the device in the
Read Device Identifier state (see Section 9.2, “Device Commands” on page 45). Next,
perform a read operation using the address offset corresponding to the register to be
read. Table 33, “Device Identifier Information” on page 70 shows the address offsets of
the Protection Registers and Lock Registers. Register data is read 16 bits at a time.
November 2007
Order Number: 306666-11
Datasheet
67
P30
13.3.2
Programming the Protection Registers
To program any of the Protection Registers, first issue the Program Protection Register
command at the parameter’s base address plus the offset to the desired Protection
Register (see Section 9.2, “Device Commands” on page 45). Next, write the desired
Protection Register data to the same Protection Register address (see Figure 31,
“Protection Register Map” on page 67).
The device programs the 64-bit and 128-bit user-programmable Protection Register
data 16 bits at a time (see Figure 45, “Protection Register Programming Flowchart” on
page 86). Issuing the Program Protection Register command outside of the Protection
Register’s address space causes a program error (SR[4] set). Attempting to program a
locked Protection Register causes a program error (SR[4] set) and a lock error (SR[1]
set).
Note:
When programming the OTP bits for a Top Parameter Device, the following upper address
bits must also be driven properly: A[Max:17] driven high (VIH) for TSOP and Easy BGA
packages, and A[Max:16] driven high (VIH) for QUAD+ SCSP.
13.3.3
Locking the Protection Registers
Each Protection Register can be locked by programming its respective lock bit in the
Lock Register. To lock a Protection Register, program the corresponding bit in the Lock
Register by issuing the Program Lock Register command, followed by the desired Lock
Register data (see Section 9.2, “Device Commands” on page 45). The physical
addresses of the Lock Registers are 0x80 for register 0 and 0x89 for register 1. These
addresses are used when programming the lock registers (see Table 33, “Device
Identifier Information” on page 70).
Bit 0 of Lock Register 0 is already programmed at the factory, locking the lower, preprogrammed 64-bit region of the first 128-bit Protection Register containing the unique
identification number of the device. Bit 1 of Lock Register 0 can be programmed by the
user to lock the user-programmable, 64-bit region of the first 128-bit Protection
Register. When programming Bit 1 of Lock Register 0, all other bits need to be left as ‘1’
such that the data programmed is 0xFFFD.
Lock Register 1 controls the locking of the upper sixteen 128-bit Protection Registers.
Each of the 16 bits of Lock Register 1 correspond to each of the upper sixteen 128-bit
Protection Registers. Programming a bit in Lock Register 1 locks the corresponding
128-bit Protection Register.
Caution:
Datasheet
68
After being locked, the Protection Registers cannot be unlocked.
November 2007
Order Number: 306666-11
P30
14.0
Special Read States
The following sections describe non-array read states. Non-array reads can be
performed in asynchronous read or synchronous burst mode. A non-array read
operation occurs as asynchronous single-word mode. When non-array reads are performed in
asynchronous page mode only the first data is valid and all subsequent data are undefined. When a nonarray read operation occurs as synchronous burst mode, the same word of data
requested will be output on successive clock edges until the burst length requirements
are satisfied.
Refer to the following waveforms for more detailed information:
• Figure 14, “Asynchronous Single-Word Read (ADV# Low)” on page 33
• Figure 15, “Asynchronous Single-Word Read (ADV# Latch)” on page 33
• Figure 17, “Synchronous Single-Word Array or Non-array Read Timing” on page 34
14.1
Read Status Register
To read the Status Register, issue the Read Status Register command at any address.
Status Register information is available to which the Read Status Register, Word
Program, or Block Erase command was issued. Status Register data is automatically
made available following a Word Program, Block Erase, or Block Lock command
sequence. Reads from the device after any of these command sequences outputs the
device’s status until another valid command is written (e.g. Read Array command).
The Status Register is read using single asynchronous-mode or synchronous burst
mode reads. Status Register data is output on DQ[7:0], while 0x00 is output on
DQ[15:8]. In asynchronous mode the falling edge of OE#, or CE# (whichever occurs
first) updates and latches the Status Register contents. However, reading the Status
Register in synchronous burst mode, CE# or ADV# must be toggled to update status
data.
The Device Write Status bit (SR[7]) provides overall status of the device. Status
register bits SR[6:1] present status and error information about the program, erase,
suspend, VPP, and block-locked operations.
Table 32: Status Register Description (Sheet 1 of 2)
Status Register (SR)
Default Value = 0x80
Device Write
Status
Erase Suspend
Status
Erase Status
Program
Status
VPP Status
Program
Suspend
Status
Block-Locked
Status
BEFP
Status
DWS
ESS
ES
PS
VPPS
PSS
BLS
BWS
7
6
5
4
3
2
1
0
Bit
Name
Description
7
Device Write Status (DWS)
0 = Device is busy; program or erase cycle in progress; SR[0] valid.
1 = Device is ready; SR[6:1] are valid.
6
Erase Suspend Status (ESS)
0 = Erase suspend not in effect.
1 = Erase suspend in effect.
5
Erase Status (ES)
0 = Erase successful.
1 = Erase fail or program sequence error when set with SR[4,7].
4
Program Status (PS)
0 = Program successful.
1 = Program fail or program sequence error when set with SR[5,7]
November 2007
Order Number: 306666-11
Datasheet
69
P30
Table 32: Status Register Description (Sheet 2 of 2)
Status Register (SR)
Default Value = 0x80
3
VPP Status (VPPS)
0 = VPP within acceptable limits during program or erase operation.
1 = VPP < VPPLK during program or erase operation.
2
Program Suspend Status (PSS)
0 = Program suspend not in effect.
1 = Program suspend in effect.
1
Block-Locked Status (BLS)
0 = Block not locked during program or erase.
1 = Block locked during program or erase; operation aborted.
0
BEFP Status (BWS)
Note:
After Buffered Enhanced Factory Programming (BEFP) data is loaded into the
buffer:
0 = BEFP complete.
1 = BEFP in-progress.
Always clear the Status Register prior to resuming erase operations. It avoids Status Register
ambiguity when issuing commands during Erase Suspend. If a command sequence error
occurs during an erase-suspend state, the Status Register contains the command sequence
error status (SR[7,5,4] set). When the erase operation resumes and finishes, possible errors
during the erase operation cannot be detected via the Status Register because it contains the
previous error status.
14.1.1
Clear Status Register
The Clear Status Register command clears the status register. It functions independent
of VPP. The Write State Machine (WSM) sets and clears SR[7,6,2], but it sets bits
SR[5:3,1] without clearing them. The Status Register should be cleared before starting
a command sequence to avoid any ambiguity. A device reset also clears the Status
Register.
14.2
Read Device Identifier
The Read Device Identifier command instructs the device to output manufacturer code,
device identifier code, block-lock status, protection register data, or configuration
register data (see Section 9.2, “Device Commands” on page 45 for details on issuing
the Read Device Identifier command). Table 33, “Device Identifier Information” on
page 70 and Table 34, “Device ID codes” on page 71 show the address offsets and data
values for this device.
Table 33: Device Identifier Information (Sheet 1 of 2)
Address(1)
Data
Manufacturer Code
0x00
0089h
Device ID Code
0x01
Item
Block Lock Configuration:
Table 34)
Lock Bit:
• Block Is Unlocked
• Block Is Locked
ID (see
DQ 0 = 0b0
BBA + 0x02
DQ 0 = 0b1
• Block Is not Locked-Down
DQ 1 = 0b0
• Block Is Locked-Down
DQ 1 = 0b1
Read Configuration Register
0x05
RCR Contents
Lock Register 0
0x80
PR-LK0
64-bit Factory-Programmed Protection Register
0x81–0x84
Factory Protection Register Data
64-bit User-Programmable Protection Register
0x85–0x88
User Protection Register Data
Datasheet
70
November 2007
Order Number: 306666-11
P30
Table 33: Device Identifier Information (Sheet 2 of 2)
Item
Address(1)
Lock Register 1
128-bit User-Programmable Protection Registers
Data
0x89
PR-LK1
0x8A–0x109
Protection Register Data
Notes:
1.
BBA = Block Base Address.
Table 34: Device ID codes
Device Identifier Codes
ID Code Type
Device Code
Note:
14.3
Device Density
–T
(Top Parameter)
–B
(Bottom Parameter)
64-Mbit
8817
881A
128-Mbit
8818
881B
256-Mbit
8919
891C
The 512-Mbit devices do not have a Device ID associated with them. Each die within the stack can be identified by
either of the 256-Mbit Device ID codes depending on its parameter option.
CFI Query
The CFI Query command instructs the device to output Common Flash Interface (CFI)
data when read. See Section 9.2, “Device Commands” on page 45 for details on issuing
the CFI Query command. Appendix C, “Common Flash Interface” on page 87 shows CFI
information and address offsets within the CFI database.
November 2007
Order Number: 306666-11
Datasheet
71
P30
Appendix A Write State Machine
Figure 32 through Figure 37 show the command state transitions (Next State Table)
based on incoming commands. Only one partition can be actively programming or
erasing at a time. Each partition stays in its last read state (Read Array, Read Device
ID, CFI Query or Read Status Register) until a new command changes it. The next WSM
state does not depend on the partition’s output state.
Figure 32: Write State Machine—Next State Table (Sheet 1 of 6)
Command Input to Chip and resulting Chip Next State
Current Chip
(7)
State
Ready
Read
Array
(2)
Program
(3,4)
(FFH)
(10H/40H)
Ready
Program
Setup
Buffered
Program
(BP)
Erase
Setup
(3,4)
Buffered
Enhanced
Factory Pgm
Setup (3, 4)
(E8H)
(20H)
BP Setup
Erase
Setup
(80H)
Confirm
BP / Prg /
Erase
Suspend
Read
Status
(B0H)
(70H)
Setup
Clear
Status
Register
Read
ID/Query
(5)
Lock, Unlock,
Lock-down,
CR setup (4)
(8)
(D0H)
(50H)
(90H, 98H)
(60H)
Lock/CR
Setup
Ready
Ready
(Unlock
Block)
Ready (Lock Error)
OTP Busy
Busy
Word Program Busy
Setup
Word
Program
BE Confirm,
P/E
Resume,
ULB,
BEFP Setup
Ready (Lock Error)
Lock/CR Setup
OTP
Word
Word
Program
Suspend
Program Busy
Busy
Word
Program
Busy
Word Program Suspend
Suspend
Word Program Busy
Word Program Suspend
Setup
BP Load 1
BP Load 1
BP Load 2
BP Load 2
BP Confirm if Data load into Program Buffer is complete; Else BP Load 2
BP
BP
Confirm
Ready (Error)
BP Busy
BP Busy
BP Suspend
BP Busy
Setup
Ready (Error)
Erase Busy
Suspend
Datasheet
72
Erase
Suspend
Word
Program
Setup in
Erase
Suspend
BP Setup in
Erase
Suspend
BP Suspend
Ready (Error)
Erase
Suspend
Erase Busy
Busy
BP Busy
BP Suspend
BP
Suspend
Erase
Ready (Error)
BP Busy
Erase Suspend
Erase Busy
Erase Busy
Erase Suspend
Lock/CR
Setup in
Erase
Suspend
November 2007
Order Number: 306666-11
P30
Figure 33: Write State Machine—Next State Table (Sheet 2 of 6)
Command Input to Chip and resulting Chip Next State
Current Chip
(7)
State
Read
Array (2)
(FFH)
Word
Program (3,4)
(10H/40H)
Buffered
Program
(BP)
(E8H)
Buffered
Erase
Enhanced
(3,4) Factory Pgm
Setup
Setup (3, 4)
(20H)
Word Program Suspend in Erase Suspend
(B0H)
(70H)
Clear
Status
Register
(D0H)
Word
Program
Suspend in
Erase
Suspend
Read
ID/Query
(90H, 98H)
Lock, Unlock,
Lock-down,
CR setup (4)
(60H)
Word
Program
Busy in
Erase
Suspend
Word Program Busy in Erase Suspend Busy
Word Program Suspend in Erase Suspend
BP Load 1
BP Load 1
BP Load 2
BP Load 2
BP Confirm if Data load into Program Buffer is complete; Else BP Load 2
BP
Confirm
Erase Suspend (Error)
BP Busy in
Erase
Suspend
Lock/CR Setup in Erase
Suspend
Setup
Ready (Error in Erase Suspend)
BP Suspend
in Erase
Suspend
BP Busy in Erase Suspend
BP
Suspend
BEFP
Busy
(5)
(50H)
Setup
BP Busy
Buffered
Enhanced
Factory
Program
Mode
Read
Status
Confirm (8)
Word Program Busy in Erase Suspend
Busy
Suspend
BP in Erase
Suspend
BP / Prg /
Erase
Suspend
Word Program Busy in Erase Suspend
Setup
Word
Program in
Erase
Suspend
(80H)
BE Confirm,
P/E
Resume,
ULB,
BP Busy in Erase Suspend
BP Suspend in Erase Suspend
BP Busy in
Erase
Suspend
BP Suspend in Erase Suspend
Erase Suspend (Lock Error)
Erase
Suspend
(Unlock
Block)
Erase Suspend (Lock Error [Botch])
Ready (Error)
BEFP
Loading
Data (X=32)
Ready (Error)
BEFP Program and Verify Busy (if Block Address given matches address given on BEFP Setup command). Commands treated as data. (7)
November 2007
Order Number: 306666-11
Datasheet
73
P30
Figure 34: Write State Machine—Next State Table (Sheet 3 of 6)
Command Input to Chip and resulting Chip Next State
Current Chip
(7)
State
OTP
Setup (4)
(C0H)
Ready
OTP
Setup
Lock/CR Setup
Ready
(Lock
Error)
OTP
Word
Program
Lock
Block
Confirm (8)
Lock-Down
Block
Confirm (8)
(01H)
(2FH)
Write RCR
Block Address
(8)
Confirm
(?WA0)
(03H)
9
(XXXXH)
Illegal Cmds or
BEFP Data (1)
WSM
Operation
Completes
(all other codes)
Ready
Ready
(Lock
Block)
Ready
(Lock Down
Blk)
Setup
Ready
(Set CR)
Ready (Lock Error)
OTP Busy
Busy
N/A
Ready
Setup
Word Program Busy
N/A
Busy
Word Program Busy
Ready
Suspend
Word Program Suspend
Setup
BP Load 1
BP Load 1
BP Load 2
BP Load 2
BP Confirm if Data load into Program Buffer is
complete; ELSE BP load 2
Ready (BP Load 2 BP Load 2
Ready
BP
BP
Confirm
BP Busy
BP
Suspend
Setup
Busy
Ready (Error)
(Proceed if
unlocked or lock
error)
Ready (Error)
BP Busy
BP Confirm if
Data load into
Program Buffer is
complete; ELSE
BP Load 2
N/A
Ready (Error)
Ready
BP Suspend
N/A
Ready (Error)
Erase Busy
Ready
Erase Suspend
N/A
Erase
Suspend
Datasheet
74
November 2007
Order Number: 306666-11
P30
Figure 35: Write State Machine—Next State Table (Sheet 4 of 6)
Command Input to Chip and resulting Chip Next State
Current Chip
(7)
State
Word
Program in
Erase
Suspend
OTP
Setup (4)
Lock
Block
Confirm (8)
Lock-Down
Block
Confirm (8)
Write RCR
Confirm (8)
Block Address
(?WA0) 9
Illegal Cmds or
BEFP Data (1)
(C0H)
(01H)
(2FH)
(03H)
(XXXXH)
(all other codes)
Setup
Word Program Busy in Erase Suspend
NA
Busy
Word Program Busy in Erase Suspend Busy
Erase Suspend
Suspend
Word Program Suspend in Erase Suspend
N/A
Setup
BP Load 1
BP Load 1
BP Load 2
BP Load 2
BP Confirm if Data load into Program Buffer is
complete; Else BP Load 2
BP
Confirm
Ready (Error in Erase Suspend)
BP in Erase
Suspend
November 2007
Order Number: 306666-11
Ready (BP Load 2 BP Load 2
Ready
Ready (Error)
(Proceed if
unlocked or lock
error)
BP Busy
BP Busy in Erase Suspend
BP
Suspend
BP Suspend in Erase Suspend
Lock/CR Setup in Erase
Suspend
Buffered
Enhanced
Factory
Program
Mode
WSM
Operation
Completes
Erase
Suspend
(Lock
Error)
Erase
Suspend
(Lock
Block)
Erase
Suspend
(Lock Down
Block)
Erase
Suspend
(Set CR)
BP Confirm if
Data load into
Program Buffer is
complete; Else
BP Load 2
N/A
Ready (Error)
Erase Suspend
Erase Suspend (Lock Error)
Setup
Ready (Error)
Ready (BEFP
Loading Data)
Ready (Error)
BEFP
Busy
BEFP Program and Verify Busy (if Block Address
given matches address given on BEFP Setup
command). Commands treated as data. (7)
Ready
BEFP Busy
N/A
Ready
Datasheet
75
P30
Figure 36: Write State Machine—Next State Table (Sheet 5 of 6)
Output Next State Table
Command Input to Chip and resulting Output Mux Next State
Current chip state
Read
Array (2)
Word
Program
Setup (3,4)
BP Setup
(FFH)
(10H/40H)
(E8H)
BE Confirm,
Buffered
P/E
Enhanced
Erase
Resume,
Setup (3,4) Factory Pgm ULB Confirm
Setup (3, 4)
(8)
(20H)
(30H)
Program/
Erase
Suspend
Read
Status
(B0H)
(70H)
(D0H)
BEFP Setup,
BEFP Pgm & Verify
Busy,
Erase Setup,
OTP Setup,
BP: Setup, Load 1,
Load 2, Confirm,
Word Pgm Setup,
Word Pgm Setup in
Erase Susp,
BP Setup, Load1,
Load 2, Confirm in
Erase Suspend
Status Read
Lock/CR Setup,
Lock/CR Setup in
Erase Susp
Status Read
Clear
Status
Register (5)
(50H)
Datasheet
76
(90H, 98H)
Lock, Unlock,
Lock-down,
CR setup (4)
(60H)
Status
Read
OTP Busy
Ready,
Erase Suspend,
BP Suspend
BP Busy,
Word Program
Busy,
Erase Busy,
BP Busy
BP Busy in Erase
Suspend
Word Pgm
Suspend,
Word Pgm Busy in
Erase Suspend,
Pgm Suspend In
Erase Suspend
Read
ID/Query
Read Array
Status Read
Output does not change.
Status Read
Output mux
does not
change.
Status Read
ID Read
November 2007
Order Number: 306666-11
P30
Figure 37: Write State Machine—Next State Table (Sheet 6 of 6)
Output Next State Table
Command Input to Chip and resulting Output Mux Next State
OTP
Current chip state
Setup (4)
(C0H)
Lock
Block
Confirm
Lock-Down
Block
(8)
(01H)
BEFP Setup,
BEFP Pgm & Verify
Busy,
Erase Setup,
OTP Setup,
BP: Setup, Load 1,
Load 2, Confirm,
Word Pgm Setup,
Word Pgm Setup in
Erase Susp,
BP Setup, Load1,
Load 2, Confirm in
Erase Suspend
Confirm
(2FH)
(8)
Write CR
Confirm
(8)
(03H)
Block Address
(?WA0)
Illegal Cmds or
(FFFFH)
(all other codes)
BEFP Data (1)
Status Read
Lock/CR Setup,
Lock/CR Setup in
Erase Susp
Status Read
Array
Read
Status Read
Output does
not change.
OTP Busy
Ready,
Erase Suspend,
BP Suspend
BP Busy,
Word Program
Busy,
Erase Busy,
BP Busy
BP Busy in Erase
Suspend
Word Pgm
Suspend,
Word Pgm Busy in
Erase Suspend,
Pgm Suspend In
Erase Suspend
WSM
Operation
Completes
Status
Read
Output does not change.
Array Read
Output does not
change.
Notes:
1.
"Illegal commands" include commands outside of the allowed command set (allowed commands: 40H [pgm], 20H [erase],
etc.)
2.
If a "Read Array" is attempted from a busy partition, the result will be invalid data. The ID and Query data are located at
different locations in the address map.
3.
1st and 2nd cycles of "2 cycles write commands" must be given to the same partition address, or unexpected results will
occur.
4.
To protect memory contents against erroneous command sequences, there are specific instances in a multi-cycle
command sequence in which the second cycle will be ignored. For example, when the device is program suspended and an
erase setup command (0x20) is given followed by a confirm/resume command (0xD0), the second command will be
ignored because it is unclear whether the user intends to erase the block or resume the program operation.
5.
The Clear Status command only clears the error bits in the status register if the device is not in the following modes: WSM
running (Pgm Busy, Erase Busy, Pgm Busy In Erase Suspend, OTP Busy, BEFP modes).
6.
BEFP writes are only allowed when the status register bit #0 = 0, or else the data is ignored.
November 2007
Order Number: 306666-11
Datasheet
77
P30
7.
8.
9.
The "current state" is that of the "chip" and not of the "partition"; Each partition "remembers" which output (Array, ID/CFI
or Status) it was last pointed to on the last instruction to the "chip", but the next state of the chip does not depend on
where the partition's output mux is presently pointing to.
Confirm commands (Lock Block, Unlock Block, Lock-Down Block, Configuration Register) perform the operation and then
move to the Ready State.
WA0 refers to the block address latched during the first write cycle of the current operation.
Datasheet
78
November 2007
Order Number: 306666-11
P30
Appendix B Flowcharts
Figure 38: Word Program Flowchart
WORD PROGRAM PROCEDURE
Bus
Operation Command
Start
Write
Write 0x40,
Word Address
(Setup)
Write Data,
Word Address
Program Data = 0x40
Setup Addr = Location to program
Write
Data
Data = Data to program
Addr = Location to program
Read
None
Status register data
Idle
None
Check SR[7]
1 = WSM Ready
0 = WSM Busy
(Confirm)
Program
Suspend
Loop
Read Status
Register
No
SR[7] =
Comments
0
Suspend?
Yes
Repeat for subsequent Word Program operations.
Full Status Register check can be done after each program, or
after a sequence of program operations.
1
Full Status
Check
(if desired)
Write 0xFF after the last operation to set to the Read Array
state.
Program
Complete
FULL STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
SR[4] =
Idle
None
Check SR[3]:
1 = VPP Error
Idle
None
Check SR[4]:
1 = Data Program Error
Idle
None
Check SR[1]:
1 = Block locked; operation aborted
VPP Range
Error
0
1
Program
Error
1
Device
Protect Error
Comments
0
SR[1] =
If an error is detected, clear the Status Register before
continuing operations - only the Clear Staus Register
command clears the Status Register error bits.
0
Program
Successful
November 2007
Order Number: 306666-11
Datasheet
79
P30
Figure 39: Program Suspend/Resume Flowchart
PROGRAM SUSPEND / RESUME PROCEDURE
Bus
Command
Operation
Start
Read
Status
Write
Write 70 h
Write
Program Suspend
Write B0h
Any Address
0
Status register data
Initiate a read cycle to update Status
register
Addr = Suspended block (BA)
Standby
Check SR.7
1 = WSM ready
0 = WSM busy
Standby
Check SR.2
1 = Program suspended
0 = Program completed
1
SR.2 =
Read
0
Program
Completed
1
Array
Data = 70h
Addr = Block to suspend (BA )
Program Data = B0h
Suspend Addr = X
Read
Read Status
Register
SR.7 =
Read
Status
Comments
Write
Read
Array
Data = FFh
Addr = Block address to read (BA)
Write FFh
Read
Read Array
Data
Done
Reading
Program
Yes
Resume
Write
Read array data from block other than
the one being programmed
Program Data = D0 h
Resume Addr = Suspended block (BA)
No
Read
Array
Write D0 h
Any Address
Write FFh
Program
Resumed
Read Array
Data
PGM_SUS.WMF
Datasheet
80
November 2007
Order Number: 306666-11
P30
Figure 40: Buffer Program Flowchart
Start
Bus
Operation
Command
Write
Write to
Buffer
No
Use Single Word
Programming
Yes
Get Next
Target Address
Issue Write to Buffer
Command E8h and
Block Address
Data = N-1 = Word Count
N = 0 corresponds to count = 1
Addr = Block Address
Write
(Notes 3, 4)
Data = Write Buffer Data
Addr = Start Address
Write
(Notes 5, 6)
Data = Write Buffer Data
Addr = Block Address
Read
No
0 = No
Standby
Timeout
or Count
Expired?
1 = Yes
Write Buffer Data,
Start Address
X= X+1
X=0
Write Buffer Data,
Block Address
Yes
Data = D0H
Addr = Block Address
Status register Data
CE# and OE# low updates SR
Addr = Block Address
Check SR.7
1 = WSM Ready
0 = WSM Busy
Full status check can be done after all erase and write
sequences complete. Write FFh after the last operation to reset
the device to read array mode.
No
No
Program
Confirm
1. Word count values on DQ0-DQ7 are loaded into the Count
register. Count ranges for this device are N = 0000h to 0001Fh.
2. The device outputs the status register when read.
3. Write Buffer contents will be programmed at the device start
address or destination flash address.
4. Align the start address on a Write Buffer boundary for
maximum programming performance (i.e., A4–A0 of the start
address = 0).
5. The device aborts the Buffered Program command if the
current address is outside the original block address.
6. The Status register indicates an "improper command
sequence" if the Buffered Program command is aborted. Follow
this with a Clear Status Register command.
Yes
Write Word Count,
Block Address
X = N?
Write
(Notes 1, 2)
Write
Read Status Register
(at Block Address)
Is WSM Ready?
SR.7 =
Check SR.7
1 = Device WSM is Busy
0 = Device WSM is Ready
Standby
Set Timeout or
Loop Counter
Data = E8H
Addr = Block Address
SR.7 = Valid
Addr = Block Address
Read
Device
Supports Buffer
Writes?
Comments
Abort Bufferred
Program?
Yes
Write Confirm D0h
and Block Address
Write to another
Block Address
Buffered Program
Aborted
Read Status Register
No
SR.7 =?
0
Suspend
Program
Yes
Suspend
Program
Loop
Full Status
Check if Desired
1
Yes
Another Buffered
Programming?
No
Program Complete
November 2007
Order Number: 306666-11
Datasheet
81
P30
Figure 41: BEFP Flowchart
BUFFERED ENHANCED FACTORY PROGRAMMING (BEFP) PROCEDURE
Setup Phase
Program & Verify Phase
Exit Phase
Start
Read
Status Reg.
Read
Status Reg.
V PP applied
Block Unlocked
No (SR[0]=1)
No (SR[7]=0)
Data Stream
Ready?
BEFP
Exited?
Yes (SR[0]=0)
W rite 80h @
1 st Word Address
W rite D0h @
1 st Word Address
BEFP Setup delay
Full Status Check
Procedure
W rite Data @ 1 st
W ord Address
Program
Complete
Increment Count:
X = X+1
Read
Status Reg.
BEFP Setup
Done?
Yes (SR[7]=1)
Initialize Count:
X=0
N
Check
X = 32?
Yes (SR[7]=0)
Y
Read
Status Reg.
No (SR[7]=1)
No (SR [0]=1)
Check V P P, Lock
errors (SR[3,1])
Program
Done?
Yes (SR[0]=0)
Exit
N
Last
Data?
Y
W rite 0xFFFF,
Address Not within
Current Block
BEFP Setup
BEFP Exit
BEFP Program & Verify
Bus
State
Operation
Write
Unlock
Block
V PPH applied to VPP
Write
(Note 1)
BEFP
Setup
Data = 0x80 @ 1 st W ord
Address
Com ments
Bus
State
Operation
Com ments
Bus
State
Operation
Com ments
Read
Status
Register
Data = Status Register Data
Address = 1 st W ord Addr.
Read
Status
Register
Data = Status Register Data
Address = 1 st W ord Addr.
Standby
Data Stream
Ready?
Check SR[0]:
0 = Ready for Data
1 = Not Ready for Data
Standby
Check
Exit
Status
Standby
Initialize
Count
X=0
Repeat for subsequent blocks ;
Write
(note 2)
Load
Buffer
Data = Data to Program
Address = 1 st W ord Addr.
After BEFP exit, a full Status Register check can
determine if any program error occurred ;
Standby
Increment
Count
X = X+1
See full Status Register check procedure in the
W ord Program flowchart.
Standby
Buffer
Full?
X = 32?
Yes = Read SR[0]
No = Load Next Data W ord
W rite 0xFF to enter Read Array state .
Read
Status
Register
Data = Status Reg. Data
Address = 1 st W ord Addr.
Standby
Program
Done?
Check SR[0]:
0 = Program Done
1 = Program in Progress
Standby
Last
Data?
st
Write
BEFP
Confirm
Data = 0x80 @ 1 W ord
1
Address
Read
Status
Register
Data = Status Register Data
Address = 1 st W ord Addr.
Standby
BEFP
Setup
Done?
Standby
Error
Condition
Check
Check SR[7]:
0 = BEFP Ready
1 = BEFP Not Ready
If SR[7] is set, check:
SR[3] set = V PP Error
SR[1] set = Locked Block
Write
Check SR [7]:
0 = Exit Not Completed
1 = Exit Completed
No = Fill buffer again
Yes = Exit
Exit Prog & Data = 0xFFFF @ address
Verify Phase not in current block
NOTES:
1. First-word address to be programmed within the target block must be aligned on a write -buffer boundary.
2. W rite-buffer contents are programmed sequentially to the flash array starting at the first word address (W SM internally increments addressing ).
Datasheet
82
November 2007
Order Number: 306666-11
P30
Figure 42: Block Erase Flowchart
BLOCK ERASE PROCEDURE
Bus
Comments
Operation Command
Block
Data = 0x20
Write
Erase
Addr = Block to be erased (BA)
Setup
Start
Write 0x20,
(Block Erase)
Block Address
Write
Write 0xD0,
(Erase Confirm)
Block Address
Suspend
Erase
Loop
Read Status
Register
No
0
SR[7] =
Suspend
Erase
1
Erase Data = 0xD0
Confirm Addr = Block to be erased (BA)
Read
None
Status Register data.
Idle
None
Check SR[7]:
1 = WSM ready
0 = WSM busy
Yes
Repeat for subsequent block erasures.
Full Status register check can be done after each block erase
or after a sequence of block erasures.
Full Erase
Status Check
(if desired)
Write 0xFF after the last operation to enter read array mode.
Block Erase
Complete
FULL ERASE STATUS CHECK PROCEDURE
Read Status
Register
SR[3] =
Bus
Command
Operation
1
VPP Range
Error
0
SR[4,5] =
1,1
Command
Sequence Error
Idle
None
Check SR[3]:
1 = VPP Range Error
Idle
None
Check SR[4,5]:
Both 1 = Command Sequence Error
Idle
None
Check SR[5]:
1 = Block Erase Error
Idle
None
Check SR[1]:
1 = Attempted erase of locked block;
erase aborted.
0
SR[5] =
1
Block Erase
Error
1
Block Locked
Error
0
SR[1] =
Comments
Only the Clear Status Register command clears SR[1, 3, 4, 5].
If an error is detected, clear the Status register before
attempting an erase retry or other error recovery.
0
Block Erase
Successful
November 2007
Order Number: 306666-11
Datasheet
83
P30
Figure 43: Erase Suspend/Resume Flowchart
ERASE SUSPEND / RESUME PROCEDURE
Bus
Command
Operation
Start
Read
Status
Write
Write 70h
Any Address
Write
Erase Suspend
Write B0h
Any Address
Read
Read Status
Register
SR.7 =
SR.6 =
0
Read
Read or
Program ?
Read Array
Data
No
Check SR.6
1 = Erase suspended
0 = Erase completed
Read or
Write
Program
Loop
Status register data. Toggle CE# or
OE# to update Status register
Addr =X
Standby
Write
Program
Data = B0h
Erase
Addr = Same partition address as
Suspend
above
Check SR.7
1 = WSM ready
0 = WSM busy
Erase
Completed
1
Data = 70 h
Addr = Any device address
Standby
0
1
Read
Status
Comments
Write
Read Array Data = FFh or 40h
or Program Addr = Block to program or read
Read array or program data from/to
block other than the one being erased
Program Data = D0h
Resume Addr = Any address
Done?
Yes
Erase Resume
Read
Write D0h
Any Address
Write FFh
Any Addres
Erase
Resumed
Read Array
Data
Read
Status
Write 70h
Any Address
Datasheet
84
Array
ERAS_SUS.WMF
November 2007
Order Number: 306666-11
P30
Figure 44: Block Lock Operations Flowchart
LOCKING OPERATIONS PROCEDURE
Bus
Command
Operation
Start
Lock
Setup
Write
Write 60 h
Block Address
Lock
Confirm
Write
Write 01 ,D0,2Fh
Block Address
Lock
Setup
Comments
Data = 60h
Addr = Block to lock/unlock/lock-down (BA)
Lock,
Data = 01h (Lock block)
Unlock, or
D0h (Unlock block)
Lockdown
2Fh (Lockdown block)
Confirm Addr = Block to lock/unlock/lock-down (BA)
Read ID Plane
Write
( Optional)
Op tion al
Write 90 h
No
Yes
Read
Data = 90h
Addr = Block address offset +2 ( BA+2 )
Read
Block Lock Block Lock status data
( Optional)
Status Addr = Block address offset +2 ( BA+2 )
Read Block Lock
Status
Locking
Change ?
Read ID
Plane
Array
Confirm locking change on DQ1, DQ0 .
(See Block Locking State Transitions Table
for valid combinations.)
Standby
( Optional)
Write
Read
Array
Data = FFh
Addr = Block address (BA)
Write FFh
Any Address
Lock Change
Complete
November 2007
Order Number: 306666-11
LOCK_OP.WMF
Datasheet
85
P30
Figure 45: Protection Register Programming Flowchart
PROTECTION REGISTER PROGRAMMING PROCEDURE
Bus
Operation Command
Start
Write 0xC0,
PR Address
Program Data = 0xC0
PR Setup Addr = First Location to Program
Write
Protection Data = Data to Program
Program Addr = Location to Program
(Confirm Data)
Read Status
Register
SR[7] =
Write
(Program Setup)
Write PR
Address & Data
Comments
Read
None
Status Register Data.
Idle
None
Check SR[7]:
1 = WSM Ready
0 = WSM Busy
Program Protection Register operation addresses must be
within the Protection Register address space. Addresses
outside this space will return an error.
0
1
Repeat for subsequent programming operations.
Full Status
Check
(if desired)
Full Status Register check can be done after each program, or
after a sequence of program operations.
Write 0xFF after the last operation to set Read Array state.
Program
Complete
FULL STATUS CHECK PROCEDURE
Read Status
Register Data
SR[3] =
Bus
Command
Operation
1
SR[4] =
1
Program Error
0
SR[1] =
Idle
None
Check SR[3]:
1 =VPP Range Error
Idle
None
Check SR[4]:
1 =Programming Error
Idle
None
Check SR[1]:
1 =Block locked; operation aborted
VPP Range Error
0
Comments
Only the Clear Staus Register command clears SR[1, 3, 4].
1
Register Locked;
Program Aborted
If an error is detected, clear the Status register before
attempting a program retry or other error recovery.
0
Program
Successful
Datasheet
86
November 2007
Order Number: 306666-11
P30
Appendix C Common Flash Interface
The Common Flash Interface (CFI) is part of an overall specification for multiple
command-set and control-interface descriptions. This appendix describes the database
structure containing the data returned by a read operation after issuing the CFI Query
command (see Section 9.2, “Device Commands” on page 45). System software can
parse this database structure to obtain information about the flash device, such as
block size, density, bus width, and electrical specifications. The system software will
then know which command set(s) to use to properly perform flash writes, block erases,
reads and otherwise control the flash device.
C.1
Query Structure Output
The Query database allows system software to obtain information for controlling the
flash device. This section describes the device’s CFI-compliant interface that allows
access to Query data.
Query data are presented on the lowest-order data outputs (DQ7-0) only. The numerical
offset value is the address relative to the maximum bus width supported by the device.
On this family of devices, the Query table device starting address is a 10h, which is a
word address for x16 devices.
For a word-wide (x16) device, the first two Query-structure bytes, ASCII “Q” and “R,”
appear on the low byte at word addresses 10h and 11h. This CFI-compliant device
outputs 00h data on upper bytes. The device outputs ASCII “Q” in the low byte (DQ7-0)
and 00h in the high byte (DQ15-8).
At Query addresses containing two or more bytes of information, the least significant
data byte is presented at the lower address, and the most significant data byte is
presented at the higher address.
In all of the following tables, addresses and data are represented in hexadecimal
notation, so the “h” suffix has been dropped. In addition, since the upper byte of wordwide devices is always “00h,” the leading “00” has been dropped from the table
notation and only the lower byte value is shown. Any x16 device outputs can be
assumed to have 00h on the upper byte in this mode.
Table 35: Summary of Query Structure Output as a Function of Device and Mode
Device
Device Addresses
November 2007
Order Number: 306666-11
Hex
Offset
00010:
00011:
00012:
Hex
Code
51
52
59
ASCII
Value
"Q"
"R"
"Y"
Datasheet
87
P30
Table 36: Example of Query Structure Output of x16- Devices
Word Addressing:
Hex Code
D15–D0
0051
0052
0059
P_IDLO
P_IDHI
PLO
PHI
A_IDLO
A_IDHI
...
Offset
AX–A0
00010h
00011h
00012h
00013h
00014h
00015h
00016h
00017h
00018h
...
C.2
Value
Offset
AX–A0
00010h
00011h
00012h
00013h
00014h
00015h
00016h
00017h
00018h
...
"Q"
"R"
"Y"
PrVendor
ID #
PrVendor
TblAdr
AltVendor
ID #
...
Byte Addressing:
Hex Code
D7–D0
51
52
59
P_IDLO
P_IDLO
P_IDHI
...
Value
"Q"
"R"
"Y"
PrVendor
ID #
ID #
...
Query Structure Overview
The Query command causes the flash component to display the Common Flash
Interface (CFI) Query structure or “database.” The structure sub-sections and address
locations are summarized below.
Table 37: Query Structure
Offset
00001-Fh
00010h
0001Bh
00027h
P(3)
Description(1)
Reserved
Reserved for vendor-specific information
CFI query identification string
Command set ID and vendor data offset
System interface information
Device timing & voltage information
Device geometry definition
Flash device layout
Vendor-defined additional information specific
Primary Intel-specific Extended Query Table
to the Primary Vendor Algorithm
Sub-Section Name
Notes:
1.
Refer to the Query Structure Output section and offset 28h for the detailed definition of offset address as a function of
device bus width and mode.
2.
BA = Block Address beginning location (i.e., 08000h is block 1’s beginning location when the block size is 32-KWord).
3.
Offset 15 defines “P” which points to the Primary Numonyx-specific Extended Query Table.
C.3
CFI Query Identification String
The Identification String provides verification that the component supports the
Common Flash Interface specification. It also indicates the specification version and
supported vendor-specified command set(s).
Table 38: CFI Identification
Datasheet
88
Offset
Length
Description
10h
3
Query-unique ASCII string “QRY“
13h
2
15h
2
Primary vendor command set and control interface ID code.
16-bit ID code for vendor-specified algorithms
Extended Query Table primary algorithm address
17h
2
19h
2
Alternate vendor command set and control interface ID code.
0000h means no second vendor-specified algorithm exists
Secondary algorithm Extended Query Table address.
0000h means none exists
Hex
Add. Code Value
10:
--51
"Q"
11:
--52
"R"
12:
--59
"Y"
13:
--01
14:
--00
15:
--0A
16:
--01
17:
--00
18:
--00
19:
--00
1A:
--00
November 2007
Order Number: 306666-11
P30
Table 39: System Interface Information
Offset
Length
1Bh
1
1Ch
1
1Dh
1
1Eh
1
1Fh
20h
21h
22h
23h
24h
25h
26h
1
1
1
1
1
1
1
1
November 2007
Order Number: 306666-11
Description
Hex
Add. Code
1B:
--17
VCC logic supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
1C:
VCC logic supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 BCD volts
1D:
VPP [programming] supply minimum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
1E:
VPP [programming] supply maximum program/erase voltage
bits 0–3 BCD 100 mV
bits 4–7 HEX volts
1F:
“n” such that typical single word program time-out = 2n μ-sec
20:
“n” such that typical max. buffer write time-out = 2n μ-sec
21:
“n” such that typical block erase time-out = 2n m-sec
22:
“n” such that typical full chip erase time-out = 2n m-sec
“n” such that maximum word program time-out = 2n times typical 23:
24:
“n” such that maximum buffer write time-out = 2n times typical
25:
“n” such that maximum block erase time-out = 2n times typical
26:
“n” such that maximum chip erase time-out = 2n times typical
Value
1.7V
--20
2.0V
--85
8.5V
--95
9.5V
--08
--09
--0A
--00
--01
--01
--02
--00
256μs
512μs
1s
NA
512μs
1024μs
4s
NA
Datasheet
89
P30
C.4
Device Geometry Definition
Table 40: Device Geometry Definition
Offset
27h
28h
Length
Description
“n” such that device size = 2n in number of bytes
1
Flash device interface code assignment:
"n" such that n+1 specifies the bit field that represents the flash
device width capabilities as described in the table:
2
2Ah
2
2Ch
1
2Dh
31h
35h
4
4
4
7
6
5
4
3
2
1
0
—
—
—
—
x64
x32
x16
x8
15
14
13
12
11
10
9
8
—
—
—
—
—
—
—
—
“n” such that maximum number of bytes in write buffer = 2n
Number of erase block regions (x) within device:
1. x = 0 means no erase blocking; the device erases in bulk
2. x specifies the number of device regions with one or
more contiguous same-size erase blocks.
3. Symmetrically blocked partitions have one blocking region
Erase Block Region 1 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
bits 16–31 = z, region erase block(s) size are z x 256 bytes
Erase Block Region 2 Information
bits 0–15 = y, y+1 = number of identical-size erase blocks
bits 16–31 = z, region erase block(s) size are z x 256 bytes
Reserved for future erase block region information
A ddress
27:
28:
29:
2A :
2B:
2C:
2D:
2E:
2F:
30:
31:
32:
33:
34:
35:
36:
37:
38:
Datasheet
90
64-Mbit
–B
--17
--01
--00
--06
--00
--02
--03
--00
--80
--00
--3E
--00
--00
--02
--00
--00
--00
--00
–T
--17
--01
--00
--06
--00
--02
--3E
--00
--00
--02
--03
--00
--80
--00
--00
--00
--00
--00
128-Mbit
–B
–T
--18
--18
--01
--01
--00
--00
--06
--06
--00
--00
--02
--02
--03
--7E
--00
--00
--80
--00
--00
--02
--7E
--03
--00
--00
--00
--80
--02
--00
--00
--00
--00
--00
--00
--00
--00
--00
Code
27:
See table below
28:
--01
x16
29:
2A:
2B:
2C:
--00
--06
--00
64
See table below
2D:
2E:
2F:
30:
31:
32:
33:
34:
35:
36:
37:
38:
See table below
See table below
See table below
256-Mbit
–B
–T
--19
--19
--01
--01
--00
--00
--06
--06
--00
--00
--02
--02
--03
--FE
--00
--00
--80
--00
--00
--02
--FE
--03
--00
--00
--00
--80
--02
--00
--00
--00
--00
--00
--00
--00
--00
--00
November 2007
Order Number: 306666-11
P30
C.5
Numonyx-Specific Extended Query Table
Table 41: Primary Vendor-Specific Extended Query
Description
Offset(1) Length
P = 10Ah
(Optional flash features and commands)
(P+0)h
3
Primary extended query table
(P+1)h
Unique ASCII string “PRI“
(P+2)h
(P+3)h
1
Major version number, ASCII
(P+4)h
1
Minor version number, ASCII
(P+5)h
4
Optional feature and command support (1=yes, 0=no)
(P+6)h
bits 11–29 are reserved; undefined bits are “0.” If bit 31 is
(P+7)h
“1” then another 31 bit field of Optional features follows at
the end of the bit–30 field.
(P+8)h
bit 0 Chip erase supported
bit 1 Suspend erase supported
bit 2 Suspend program supported
bit 3 Legacy lock/unlock supported
bit 4 Queued erase supported
bit 5 Instant individual block locking supported
bit 6 Protection bits supported
bit 7 Pagemode read supported
bit 8 Synchronous read supported
bit 9 Simultaneous operations supported
bit 10 Extended Flash Array Blocks supported
bit 30 CFI Link(s) to follow
bit 31 Another "Optional Features" field to follow
(P+9)h
1
(P+A)h
(P+B)h
2
(P+C)h
1
(P+D)h
1
Address
112:
November 2007
Order Number: 306666-11
Supported functions after suspend: read Array, Status, Query
Other supported operations are:
bits 1–7 reserved; undefined bits are “0”
bit 0 Program supported after erase suspend
Block status register mask
bits 2–15 are Reserved; undefined bits are “0”
bit 0 Block Lock-Bit Status register active
bit 1 Block Lock-Down Bit Status active
bit 4 EFA Block Lock-Bit Status register active
bit 5 EFA Block Lock-Down Bit Status active
VCC logic supply highest performance program/erase voltage
bits 0–3 BCD value in 100 mV
bits 4–7 BCD value in volts
VPP optimum program/erase supply voltage
bits 0–3 BCD value in 100 mV
bits 4–7 HEX value in volts
Discrete
–B
–T
––--00
--00
Hex
Add. Code Value
10A
--50
"P"
10B:
--52
"R"
10C:
--49
"I"
10D:
--31
"1"
10E:
--34
"4"
--E6
10F:
110:
--01
111:
--00
112: See table below
bit 0 = 0
No
bit 1 = 1
Yes
bit 2 = 1
Yes
bit 3 = 0
No
bit 4 = 0
No
bit 5 = 1
Yes
bit 6 = 1
Yes
bit 7 = 1
Yes
bit 8 = 1
Yes
bit 9 = 0
No
bit 10 = 0
No
See
bit 30
table
bit 31
below
113:
--01
bit 0
114:
115:
bit 0
bit 1
bit 4
bit 5
116:
=1
--03
--00
=1
=1
=0
=0
--18
Yes
Yes
Yes
No
No
1.8V
117:
--90
9.0V
512-Mbit
–B
die 1 (B)
--40
–T
die 2 (T)
--00
die 1 (T)
--40
die 2 (B)
--00
Datasheet
91
P30
Table 42: Protection Register Information
(1)
Hex
Length
Description
Offset
Add. Code Value
P = 10Ah
(Optional flash features and commands)
(P+E)h
1
118: --02
2
Number of Protection register fields in JEDEC ID space.
“00h,” indicates that 256 protection fields are available
(P+F)h
4
Protection Field 1: Protection Description
119: --80
80h
(P+10)h
This field describes user-available One Time Programmable
11A: --00
00h
(P+11)h
(OTP) Protection register bytes. Some are pre-programmed
11B: --03 8 byte
with device-unique serial numbers. Others are user
(P+12)h
11C: --03 8 byte
programmable. Bits 0–15 point to the Protection register Lock
byte, the section’s first byte. The following bytes are factory
pre-programmed and user-programmable.
bits
bits
bits
bits
(P+13)h
(P+14)h
(P+15)h
(P+16)h
(P+17)h
(P+18)h
(P+19)h
(P+1A)h
(P+1B)h
(P+1C)h
10
0–7 = Lock/bytes Jedec-plane physical low address
8–15 = Lock/bytes Jedec-plane physical high address
16–23 = “n” such that 2n = factory pre-programmed bytes
24–31 = “n” such that 2n = user programmable bytes
Protection Field 2: Protection Description
Bits 0–31 point to the Protection register physical Lock-word
address in the Jedec-plane.
Following bytes are factory or user-programmable.
bits 32–39 = “n” ∴ n = factory pgm'd groups (low byte)
bits 40–47 = “n” ∴ n = factory pgm'd groups (high byte)
bits 48–55 = “n” \ 2n = factory programmable bytes/group
bits 56–63 = “n” ∴ n = user pgm'd groups (low byte)
bits 64–71 = “n” ∴ n = user pgm'd groups (high byte)
bits 72–79 = “n” ∴ 2n = user programmable bytes/group
11D:
11E:
11F:
120:
121:
122:
123:
124:
125:
126:
--89
--00
--00
--00
--00
--00
--00
--10
--00
--04
89h
00h
00h
00h
0
0
0
16
0
16
Table 43: Burst Read Information
(1)
Length
Description
Offset
P = 10Ah
(Optional flash features and commands)
Page Mode Read capability
(P+1D)h
1
bits 0–7 = “n” such that 2n HEX value represents the number of
read-page bytes. See offset 28h for device word width to
determine page-mode data output width. 00h indicates no
read page buffer.
(P+1E)h
1
Number of synchronous mode read configuration fields that
follow. 00h indicates no burst capability.
(P+1F)h
1
Synchronous mode read capability configuration 1
Bits 3–7 = Reserved
bits 0–2 “n” such that 2n+1 HEX value represents the
maximum number of continuous synchronous reads when
the device is configured for its maximum word width. A value
of 07h indicates that the device is capable of continuous
linear bursts that will output data until the internal burst
counter reaches the end of the device’s burstable address
space. This field’s 3-bit value can be written directly to the
Read Configuration Register bits 0–2 if the device is
configured for its maximum word width. See offset 28h for
word width to determine the burst data output width.
(P+20)h
1
Synchronous mode read capability configuration 2
(P+21)h
1
Synchronous mode read capability configuration 3
(P+22)h
1
Synchronous mode read capability configuration 4
Datasheet
92
Hex
Add. Code Value
127: --03 8 byte
128:
--04
4
129:
--01
4
12A:
12B:
12C:
--02
--03
--07
8
16
Cont
November 2007
Order Number: 306666-11
P30
Table 44: Partition and Erase Block Region Information
(1)
Offset
P = 10Ah
Bottom
Top
(P+23)h
Description
(Optional flash features and commands)
Number of device hardware-partition regions within the device.
x = 0: a single hardware partition device (no fields follow).
x specifies the number of device partition regions containing
(P+23)h
one or more contiguous erase block regions.
See table below
Address
Bot
Top
Len
1
12D:
12D:
Table 45: Partition Region 1 Information
Offset(1)
P = 10Ah
Bottom
Top
(P+24)h (P+24)h
(P+25)h (P+25)h
(P+26)h (P+26)h
(P+27)h (P+27)h
(P+28)h (P+28)h
(P+29)h
(P+2A)h
(P+2B)h
Description
(Optional flash features and commands)
Data size of this Parition Region Information field
(# addressable locations, including this field)
Number of identical partitions within the partition region
Number of program or erase operations allowed in a partition
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+29)h Simultaneous program or erase operations allowed in other partitions while a
partition in this region is in Program mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+2A)h Simultaneous program or erase operations allowed in other partitions while a
partition in this region is in Erase mode
bits 0–3 = number of simultaneous Program operations
bits 4–7 = number of simultaneous Erase operations
(P+2B)h Types of erase block regions in this Partition Region.
x = 0 = no erase blocking; the Partition Region erases in bulk
x = number of erase block regions w/ contiguous same-size
erase blocks. Symmetrically blocked partitions have one
blocking region. Partition size = (Type 1 blocks)x(Type 1
block sizes) + (Type 2 blocks)x(Type 2 block sizes) +…+
(Type n blocks)x(Type n block sizes)
November 2007
Order Number: 306666-11
See table below
Address
Bot
Top
Len
2
12E:
12E
12F
12F
2
130:
130:
131:
131:
1
132:
132:
1
133:
133:
1
134:
134:
1
135:
135:
Datasheet
93
P30
Table 46: Partition Region 1 Information (continued)
Offset(1)
P = 10Ah
Description
Bottom
Top
(Optional flash features and commands)
(P+2C)h (P+2C)h Partition Region 1 Erase Block Type 1 Information
(P+2D)h (P+2D)h bits 0–15 = y, y+1 = # identical-size erase blks in a partition
(P+2E)h (P+2E)h
bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+2F)h (P+2F)h
(P+30)h (P+30)h Partition 1 (Erase Block Type 1)
Block erase cycles x 1000
(P+31)h (P+31)h
(P+32)h (P+32)h Partition 1 (erase block Type 1) bits per cell; internal EDAC
bits 0–3 = bits per cell in erase region
bit 4 = internal EDAC used (1=yes, 0=no)
bits 5–7 = reserve for future use
(P+33)h (P+33)h Partition 1 (erase block Type 1) page mode and synchronous mode capabilities
defined in Table 10.
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
Partition Region 1 (Erase Block Type 1) Programming Region Information
(P+34)h (P+34)h
bits 0–7 = x, 2^x = Programming Region aligned size (bytes)
(P+35)h (P+35)h
bits 8–14 = Reserved; bit 15 = Legacy flash operation (ignore 0:7)
(P+36)h (P+36)h
bits 16–23 = y = Control Mode valid size in bytes
(P+37)h (P+37)h
bits 24-31 = Reserved
(P+38)h (P+38)h
bits 32-39 = z = Control Mode invalid size in bytes
(P+39)h (P+39)h
bits 40-46 = Reserved; bit 47 = Legacy flash operation (ignore 23:16 & 39:32)
(P+3A)h (P+3A)h Partition Region 1 Erase Block Type 2 Information
(P+3B)h (P+3B)h
bits 0–15 = y, y+1 = # identical-size erase blks in a partition
(P+3C)h (P+3C)h bits 16–31 = z, region erase block(s) size are z x 256 bytes
(P+3D)h (P+3D)h
(P+3E)h (P+3E)h Partition 1 (Erase Block Type 2)
Block erase cycles x 1000
(P+3F)h (P+3F)h
(P+40)h (P+40)h Partition 1 (erase block Type 2) bits per cell; internal EDAC
bits 0–3 = bits per cell in erase region
bit 4 = internal EDAC used (1=yes, 0=no)
bits 5–7 = reserve for future use
(P+41)h (P+41)h Partition 1 (erase block Type 2) page mode and synchronous mode capabilities
defined in Table 10.
bit 0 = page-mode host reads permitted (1=yes, 0=no)
bit 1 = synchronous host reads permitted (1=yes, 0=no)
bit 2 = synchronous host writes permitted (1=yes, 0=no)
bits 3–7 = reserved for future use
Partition Region 1 (Erase Block Type 2) Programming Region Information
(P+42)h (P+42)h
bits 0–7 = x, 2^x = Programming Region aligned size (bytes)
(P+43)h (P+43)h
bits 8–14 = Reserved; bit 15 = Legacy flash operation (ignore 0:7)
(P+44)h (P+44)h
bits 16–23 = y = Control Mode valid size in bytes
(P+45)h (P+45)h
bits 24-31 = Reserved
(P+46)h (P+46)h
bits 32-39 = z = Control Mode invalid size in bytes
(P+47)h (P+47)h
bits 40-46 = Reserved; bit 47 = Legacy flash operation (ignore 23:16 & 39:32)
Datasheet
94
See table below
Address
Bot
Top
Len
4
136:
136:
137:
137:
138:
138:
139:
139:
2
13A:
13A:
13B:
13B:
1
13C:
13C:
1
13D:
13D:
1
13E:
13F:
140:
141:
142:
143:
144:
145:
146:
147:
148:
149:
14A:
13E:
13F:
140:
141:
142:
143:
144:
145:
146:
147:
148:
149:
14A:
1
14B:
14B:
14C:
14D:
14E:
14F:
150:
151:
14C:
14D:
14E:
14F:
150:
151:
6
4
2
6
November 2007
Order Number: 306666-11
P30
Table 47: Partition and Erase Block Region Information
Address
12D:
12E:
12F:
130:
131:
132:
133:
134:
135:
136:
137:
138:
139:
13A:
13B:
13C:
13D:
13E:
13F:
140:
141:
142:
143:
144:
145:
146:
147:
148:
149:
14A:
14B:
14C:
14D:
14E:
14F:
150:
151:
November 2007
Order Number: 306666-11
64-Mbit
–B
--01
--24
--00
--01
--00
--11
--00
--00
--02
--03
--00
--80
--00
--64
--00
--02
--03
--00
--80
--00
--00
--00
--80
--3E
--00
--00
--02
--64
--00
--02
--03
--00
--80
--00
--00
--00
--80
–T
--01
--24
--00
--01
--00
--11
--00
--00
--02
--3E
--00
--00
--02
--64
--00
--02
--03
--00
--80
--00
--00
--00
--80
--03
--00
--80
--00
--64
--00
--02
--03
--00
--80
--00
--00
--00
--80
128-Mbit
–B
–T
--01
--01
--24
--24
--00
--00
--01
--01
--00
--00
--11
--11
--00
--00
--00
--00
--02
--02
--03
--7E
--00
--00
--80
--00
--00
--02
--64
--64
--00
--00
--02
--02
--03
--03
--00
--00
--80
--80
--00
--00
--00
--00
--00
--00
--80
--80
--7E
--03
--00
--00
--00
--80
--02
--00
--64
--64
--00
--00
--02
--02
--03
--03
--00
--00
--80
--80
--00
--00
--00
--00
--00
--00
--80
--80
256-Mbit
–B
–T
--01
--01
--24
--24
--00
--00
--01
--01
--00
--00
--11
--11
--00
--00
--00
--00
--02
--02
--03
--FE
--00
--00
--80
--00
--00
--02
--64
--64
--00
--00
--02
--02
--03
--03
--00
--00
--80
--80
--00
--00
--00
--00
--00
--00
--80
--80
--FE
--03
--00
--00
--00
--80
--02
--00
--64
--64
--00
--00
--02
--02
--03
--03
--00
--00
--80
--80
--00
--00
--00
--00
--00
--00
--80
--80
Datasheet
95
P30
Table 48: CFI Link Information
(1)
Offset
P = 10Ah
(P+48)h
(P+49)h
(P+4A)h
(P+4B)h
Length
(P+4C)h
1
Address
152:
153:
154:
155:
156:
Datasheet
96
4
Description
(Optional flash features and commands)
CFI Link Field bit definitions
Bits 0–9 = Address offset (within 32Mbit segment) of referenced CFI table
Bits 10–27 = nth 32Mbit segment of referenced CFI table
Bits 28–30 = Memory Type
Bit 31 = Another CFI Link field immediately follows
CFI Link Field Quantity Subfield definitions
Bits 0–3 = Quantity field (n such that n+1 equals quantity)
Bit 4 = Table & Die relative location
Bit 5 = Link Field & Table relative location
Bits 6–7 = Reserved
Discrete
–B
–T
––--FF
--FF
--FF
--FF
--FF
--FF
--FF
--FF
--FF
--FF
Add.
152:
153:
154:
155:
Hex
Code
Value
See table below
156:
See table below
512-Mbit
–B
die 1 (B)
--10
--20
--00
--00
--10
–T
die 2 (T)
--FF
--FF
--FF
--FF
--FF
die 1 (T)
--10
--20
--00
--00
--10
die 2 (B)
--FF
--FF
--FF
--FF
--FF
November 2007
Order Number: 306666-11
P30
Appendix D Additional Information
Order/Document
Number
Note:
Document/Tool
309045
P30 Family Specification Update
308291
Schematic Review Checklist for Numonyx™ StrataFlash® Embedded Memory (P30)
300783
Using Numonyx™ Flash Memory: Asynchronous Page Mode and Synchronous Burst Mode
290667
Numonyx™ StrataFlash® Memory (J3) Datasheet
306667
Migration Guide for Numonyx™ StrataFlash® Memory (J3) to Numonyx™ StrataFlash® Embedded
Memory (P30/P33) Application Note 812
314750
Numonyx™ StrataFlash® Memory (P30) to Numonyx™ StrataFlash® Embedded Memory (P33)
Conversion Guide Application Note 867
290737
Numonyx™ StrataFlash® Synchronous Memory (K3/K18) Datasheet
306669
Migration Guide for Numonyx™ StrataFlash® Synchronous Memory (K3/K18) to Numonyx™
StrataFlash® Embedded Memory (P30) Application Note 825
290701
Numonyx™ Wireless Flash Memory (W18) Datasheet
290702
Numonyx™ Wireless Flash Memory (W30) Datasheet
252802
Numonyx™ Flash Memory Design for a Stacked Chip Scale Package (SCSP)
298161
Numonyx™ Flash Memory Chip Scale Package User’s Guide
253418
Numonyx™ Wireless Communications and Computing Package User's Guide
296514
Numonyx™ Small Outline Package Guide
297833
Numonyx™ Flash Data Integrator (Numonyx™ FDI) User Guide
298136
Numonyx™ Persistent Storage Manager (Numonyx™ PSM) User Guide
306668
Migration Guide for Spansion* S29GLxxxN to Numonyx™ StrataFlash ® Embedded Memory (P30/P33)
Application Note 813
Contact your local Numonyx or distribution sales office or visit Numonyx’s World Wide Web home page at http://
www.numonyx.com for technical documentation, tools, or the most current information on Numonyx™ Flash Memory.
November 2007
Order Number: 306666-11
Datasheet
97
P30
Appendix E Ordering Information for Discrete Products
Figure 46: Decoder for Discrete P30
T E 2 8 F 6 4 0 P 3 0 B 8 5
Package Designator
Access Speed
TE = 56-Lead TSOP, leaded
JS = 56-Lead TSOP, lead-free
RC = 64-Ball Easy BGA, leaded
PC = 64-Ball Easy BGA, lead-free
Parameter Location
85 ns
B = Bottom Parameter
T = Top Parameter
Product Line Designator
28F = Intel® Flash Memory
Product Fam ily
Device Density
P30 = Intel StrataFlash® Embedded Memory
V CC = 1.7 – 2.0 V
V CCQ = 1.7 – 3.6 V
640 = 64-Mbit
128 = 128-Mbit
256 = 256-Mbit
Table 49: Valid Combinations for Discrete Products
Datasheet
98
64-Mbit
128-Mbit
256-Mbit
TE28F640P30B85
TE28F128P30B85
TE28F256P30B95
TE28F640P30T85
TE28F128P30T85
TE28F256P30T95
JS28F640P30B85
JS28F128P30B85
JS28F256P30B95
JS28F640P30T85
JS28F128P30T85
JS28F256P30T95
RC28F640P30B85
RC28F128P30B85
RC28F256P30B85
RC28F640P30T85
RC28F128P30T85
RC28F256P30T85
PC28F640P30B85
PC28F128P30B85
PC28F256P30B85
PC28F640P30T85
PC28F128P30T85
PC28F256P30T85
November 2007
Order Number: 306666-11
P30
Appendix F Ordering Information for SCSP Products
Flash Family 3/4
Flash Family 1/2
Flash #4
Flash #3
Flash #2
Flash #1
Figure 47: Decoder for SCSP P30
R D 4 8 F 4 0 0 0 P 0 Z B Q 0
Package Designator
RD = Intel ® SCSP, leaded
P F = Intel® SCSP, lead-free
RC = 64-Ball Easy BG A, leaded
P C = 64-Ball Easy BG A, lead-free
T E = 56-Lead TSO P , leaded
JS = 56-Lead T SO P, lead-free
Device Details
Group Designator
48F = Flash Memory only
Q = Q UAD+ ballout
0 = Discrete ballout
Flash Density
Param eter, M ux Configuration
0
2
3
4
B = Bottom Param eter, Non Mux
T = Top Param eter, Non M ux
=
=
=
=
0 = O riginal version of the product
(refer to the latest version of the
datasheet for details)
Ballout Designator
No die
64-Mbit
128-M bit
256-M bit
I/O Voltage, CE# Configuration
Z = Individual Chip Enable(s)
V = Virtual Chip E nable(s)
V C C = 1.7 V – 2.0 V
V C C Q = 1.7 V – 3.6 V
Product Fam ily
P = Intel StrataF lash® Em bedded M em ory
0 = No die
Note:
For 512-Mbit only, “B” is used for both top and bottom Parameter/Mux configurations.
Table 50: Valid Combinations for Dual- Die Products
64-Mbit
128-Mbit
256-Mbit
512-Mbit*
RD48F2000P0ZBQ0
RD48F3000P0ZBQ0
RD48F4000P0ZBQ0
RD48F4400P0VBQ0
RD48F2000P0ZTQ0
RD48F3000P0ZTQ0
RD48F4000P0ZTQ0
PF48F4400P0VBQ0
PF48F2000P0ZBQ0
PF48F3000P0ZBQ0
PF48F4000P0ZBQ0
RC48F4400P0VB00
PF48F2000P0ZTQ0
PF48F3000P0ZTQ0
PF48F4000P0ZTQ0
PC48F4400P0VB00
TE48F4400P0VB00
JS48F4400P0VB00
Note:
* The “B” parameter is used for both “top” and “bottom” options in the 512-Mbit density.
November 2007
Order Number: 306666-11
Datasheet
99