OPTOSUPPLY OSM543T6C1E

Tops 6 Power Warm White Ceramic
LED
OSM543T6C1E
VER . 1
■
Features
●
High-power LED
●
Long lifetime operation
Based on ceramic substrate to achieve long
operating life
Typical luminous flux performance
[email protected]
Possible to attach to heat sink directly without
using print circuit board.
●
●
●
■Outline
■
Applications
●
Indoor & outdoor lighting
●
Stage lighting
●
Reading lamps
●
Display cases, furniture illumination, marker
●
Architectural illumination
●
Spotlights
■Absolute
Dimension
THP-06-4
Unit:mm
Tolerance:±0.30mm
Tolerances are for reference only
(Ta=25℃)
Maximum Rating
Item
■Directivity
Symbol
Value
Unit
DC Forward Current *1
IF
700
mA
Pulse Forward Current*2
IFP
1400
mA
Reverse Voltage
VR
15
V
Power Dissipation*1
PD
6,840
mW
Operating Temperature
Topr
-30 ~ +85
℃
Storage Temperature
Tstg
-40~ +100
℃
Lead Soldering Temperature
Tsol
260℃/5sec
-
0
0
*1, Power dissipation and forward current are the value when the module temperature is
set lower than the rating by using an adequate heat sink.
*2, Pulse width Max.10ms Duty ratio max 1/10
(Ta=25℃)
-Optical Characteristics
Item
Symbol
Condition
Min.
Typ.
Max.
<Fig.a> Forward Current Derating Curve
Unit
DC Forward Voltage
VF
IF=600mA
9.0
10.2
11.4
V
DC Reverse Current
IR
VR=15V
-
-
100
µA
Φv
IF=600mA
320
360
-
lm
IF=600mA
-
Luminous Flux
Color Temperature
CCT
3000
-
Chromaticity
x
IF=600mA
-
0.45
-
Coordinates*
y
IF=600mA
-
0.41
-
2θ1/2
IF=600mA
-
120
-
50% Power Angle
K
800
Forward Current, IF (mA)
■Electrical
700
600
500
400
300
200
100
0
0
deg
20
40
60
Case Temperature, TA (°C)
Note: Don’t drive at rated current more than 5s without heat sink for High Power series.
* Tolerance of chromaticity coordinates is +10% ,
* Tolerance of Luminous Flux is +20%
LED & Application Technologies
http://www.optosupply.com
VER A.0
80
100
Tops 6 Power Warm White Ceramic
LED
OSM543T6C1E
VER . 1
■Customer
DIY
Customers can refer to the following do DIY
THP-06-4
1 x 6W If: 0.6A Vf: 10.2V
THP-06-4
THP-06-4
2 x 6W If: 0.6A Vf: 20.4V
THP-06-4
THP-06-4
THP-06-4
3 x 6W If: 0.6A Vf: 30.6V
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
2 x 6W If: 1.2A Vf: 10.2V
4 x 6W If: 1.2A Vf: 20.4V
6 x 6W If: 1.2A Vf: 30.6V
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
THP-06-4
3 x 6W If: 1.8A Vf: 10.2V
6x 6W If: 1.8A Vf: 20.4V
9x 6W If: 1.8A Vf: 30.6V
Customer DIY
LED & Application Technologies
http://www.optosupply.com
VER A.0
Tops 6 Power Warm White Ceramic
LED
OSM543T6C1E
VER . 1
■Heat
design
The following pictures show some measurements of mounted 5W Led on the heat sink for each board A and B (See Fig 1) with
using thermograph to make an observation about heat distribution. Each boards is tested at various current conditions.
As a result, LED needs larger heat sink as much as possible to reduce its own case temperature.
Fig. 1
Configuration pattern examples for board assembly
Board
LED power
Material
Surface area (m㎡) Min.
A
5W
Al
20,600
B
10W
Al
41,200
C
25W
Al
103,000
D
50W
Al
206,000
E
100W
Al
412,000
F
200W
Al
824,000
G
300W
Al
1236,000
Above tested LED device is attached with adhesive sheet to the heatsink.
For reference's sake, Tj absolute maximum rating is defined at 115℃ as a prerequisite on design process of 5W LED.
<Fig.2> Board A (surface area=10,300m㎡)
IF=600mA
<Fig.3> Board B (surface area=20,600m㎡)
IF=600mA
LED & Application Technologies
http://www.optosupply.com
VER A.0
Tops 6 Power Warm White Ceramic
LED
OSM543T6C1E
VER . 1
■Heat
designÆDesign flow chart
1. Mounting LED(s) on the board
2. Built-in
2-1. Building on to the lighting fixture module.
2-2. Setting on the actual using condition
3. How to measure Tc
3-1. With using thermo couple. (*a,*b)
3-2. Chose the measured LED device which assumed
the highest Tc in the mounted LEDs. (*b)
3-3. Under stable temperature condition.
if NOT, go back to
4. Judgment of Tc
4-1. Not over the temperature of your standard rated ?
4-2. Not over the temperature of specified on LED
device specification sheet ? (See Fig.a)
5. Implemented above condition
*Possible to use as it stands.
procedure No.1
and reconsider.
5. NOT implemented
*Reducing forward current
*Reconsider its design of thermal
resistance
LED & Application Technologies
http://www.optosupply.com
VER A.0
Tops 6 Power Warm White Ceramic
LED
OSM543T6C1E
VER . 1
■HandlingÆManually
handling
Use tweezers to catch hold of LEDs at the base substrate part. Do not touch the lens with the tweezers and fingers.
Do not press on the lens.
LED & Application Technologies
http://www.optosupply.com
VER A.0