FEATURES - HIGH RELIABILITY FOR LOW COST - CHEAPEST AVAILABLE SMD-CLOCK-OSCILLATOR - FREQUENCY STABILITY FROM +-15 TO +-100 PPM AVAILABLE - SUPPLY VOLTAGE OF 5.0, 3.3, 2.5 AND 1.8 VDC AVAILABLE - NEW STANDARD FOR SMALL LOW COST OSCILLATORS - EXTENDED TEMPERATURE RANGE TO -40/+105°C AVAILABLE SMD-LOW-COST CLOCK-OSCILLATOR SERIES PACKAGE 5.0 VOLT FREQUENCY RANGE 3.3 VOLT FREQUENCY STABILITY OPERATING TEMPERATURE RANGE STORAGE TEMPERATURE RANGE VOLTAGE INPUT CURRENT SXO-0507 Ceramic package 7 x 5 x 1,8 mm³ 1.0 ~ 160.0 MHz 1.0 ~ 160.0 MHz +-15 ~ +-100 PPM -10/+60°C ~ -40/+105°C -55/+125°C +5.0 VDC +-10% +3.3 VDC +-10% 1.0 ~ 4.0 MHz = 10 mA max. 1.0 ~ 4.0 MHz = 10 mA max. 4.0 ~ 32.0 MHz = 30 mA max. 4.0 ~ 32.0 MHz = 20 mA max. 32.0 ~ 80.0 MHz = 45 mA max. 32.0 ~ 80.0 MHz = 30 mA max. 80.0 ~ 160.0 MHz = 80 mA max. 80.0 ~ 160.0 MHz = 40 mA max. Lower input currents are available on request. Please indicate the special value when required. 40/60% STANDARD SYMMETRY 45/55% OPTION 5 ns typical / 10 ns max. RISE AND FALL TIME 0.4 V max. "0" LEVEL TTL 5 VOLT "1" LEVEL +2.4 V min. "0" LEVEL 0.4 V (10% VDD) CMOS 5 VOLT OUTPUT "1" LEVEL +4.5 V (90%VDD) "0" LEVEL 0.4 V max. TTL 3.3 VOLT "1" LEVEL +1.4 V min. "0" LEVEL 0.1 V (10% VDD) CMOS 3.3 VOLT "1" LEVEL +2.97 V (90%VDD) TTL 1 ~ 10 TTL LOAD CMOS 15 ~ 50 pF STANDARD WITHOUT ENABLE/DISABLE FUNCTION PIN 1 OPTION WITH ENABLE/DISABLE FUNCTION "1" = Enable ENABLE/DISABLE FUNCTION IS HIGH ACTIVE "0" = Disable OTHER PARAMETERS ARE AVAILABLE ON REQUEST / CREATE HERE YOUR SPECIFICATION REV.02 / March 2010 http://www.petermann-technik.com | [email protected] PART NUMBERING SYSTEM EXAMPLE SXO3-0507-S-E-50-W-27.000MHz-T SERIES SYMMETRY PIN 1 ENABLE/DISABLE FREQUENCY STABILITY TEMPERATURE RANGE FREQUENCY TAPE AND REEL SXO-0507 FOR 5 VOLT SXO3-0507 FOR 3.3 VOLT BLANK FOR 40/60% S FOR 45/55% BLANK FOR NO E/D E FOR E/D BLANK FOR 100 PPM ANY 15 ~ 50 PPM BLANK FOR 0/+70°C N = -10/+60°C M = -20/+70°C W = -40/+85°C Y = -40/+105°C FREQUENCY IN MHz -T Please see seperate data sheets for the versions with 1.8 or 2.5 VDC supply voltage. OUTLINE DRAWING OF SXO-0507 1.4 7. 0+0. - 2 #2 2.6 1.27 0.8 5.0+- 0.2 #1 #4 #1 En able / Dis able #2 GN D #3 Output #4 Vcc 2. 0 4. 2 1. 8max FUNCTION #3 1. 8 5. 08+0.2 - PI N 5.08 (*) Cby=0.01µF http://www.petermann-technik.com | [email protected] Unit:mm INPUT CURRENT TEST CIRCUIT CMOS + #14 + + VM - POWER SUPPLY VDD TEST POINT mA M #8 A VCC OUT OSCILLATOR 0,1µF GND #1 - CL =15pF 3 4 #7 TRI-STATE-INPUT VDD OUT OE GND 0.01~0.1µF NOTE: CL includes probe and fixture capacitance 2 1 TEST CIRCUIT TTL GND + TEST POINT mA M #14 + + VM - POWER SUPPLY RL=390 #8 VDD OUT OSCILLATOR 0,1µF GND #1 - C L=15pF 1N4148 or Equiv REFLOW SOLDER PROFILE #7 TRI-STATE-INPUT NOTE: CL includes probe and fixture capacitance REF LOW 260°C 1TO5°C /s 1 to 5°C/s (CMOS LOAD) tr tf VOH 90%VDD TEMPERAT URE OUTPUT WAVE FORM CMOS COOLING PREHEAT IN G 10s max 150°C 1 to 9°C/s 25°C 60 200 50%VDD TIME (Seconds) 10%VDD Oscillators can be soldered according to the norm JEDEC J-STD-020C. VOL Th DUTY=Th/T T TAPE AND REEL DIMENSIONS P ULL DIRECTION tf 0. 3+0.1 - 1. 5+0. - 1 16.0+0.2 - 2. 0+- 0.1 7.4+0.1 - (TTL LOAD) tr 4. 0+0.1 - 7.5+0.1 1.75+0 - .1 OUTPUT WAVE FORM TTL VOH 5. 4+- 0.1 2.4V 1. 8+- 0.1 1. 7+0.1 - 8. 0+0.1 - 2. 0+0.5 21 .0+0.8 - 13.0+0.2 - 60+5 - 180+3 - 1.4V 0.4V VOL 16.2+0 - .3 Th DUTY=Th/T T http://www.petermann-technik.com | [email protected] 20.4+0 - .1 Unit: mm