I.C. / Transformer Cross Reference T3 Interface Transformers For T3, DS3, E3 & STS-1 Interfaces Complies with CCITT G.703 Matched to Leading I.C. Manufacturers Isolation 1500VRMS minimum Rise Times Compatible with Standards I.C. Part Number Single Configuration - SMD Transmit Receive AT&T Exar Silicon Sys. Silicon Sys. Silicon Sys. Silicon Sys. Transwitch Transwitch T7296 XR-T7296 SSI 78P236 DS3 SSI 78P7200 DS3 SSI 78P2361 STS1 SSI 78P2362 E3 MRT, TXC-02050 MRT, TXC-02020 E3 DS3/STS1 Single Configuration - DIP Transmit Receive T-13100 T-13100 T-13101 T-13101 T-13101 T-13101 T-13101 T-13100 --T-13100 T-13100 T-13100 T-13100 T-13100 T-13100 T-13103 T-13103 T-13102 T-13102 T-13102 T-13102 T-13102 T-13103 --T-13103 T-13103 T-13103 T-13103 T-13103 T-13103 Electrical Specifications at 25OC Available as SMD or Thru-hole package styles Operating Temp. Range: -40OC to +85OC Schematic Style "A" Schematic Style "B" 6 1 2 5 2 5 3 4 3 4 1 I.C. Manuf. Name 6 Part (1) Number Turns Ratio OCL min. ( µH ) LL max. Sec. ( µH ) Cw/w max. ( pF ) Package T-13100 T-13101 T-13102 T-13103 T-13104 T-13105 T-13107 1:1 1:2CT 1:2CT 1:1 1:2CT 1:1 1:1.73CT 40 19 19 40 40 45 50 0.14 0.14 0.14 0.14 0.14 0.12 0.10 15 15 15 15 15 13 12 6 Pin SMD 6 Pin SMD 6 Pin Dip 6 Pin Dip 6 Pin SMD 6 Pin SMD 6 Pin Dip 1:1 40 0.10 T-13108(G) (2) 1:2CT 19 0.06 T-13109(G) (2) T-15100 1:1&1:1 40 0.14 T-15101 1:2CT&1:2CT 19 0.14 T-15102 1:2CT&1:1 19/40 0.14 1. The 3 dB Bandwidth is 200kHz - 280MHz typical, 2. Reinforced Insulation (3000 VRMS) Schem. Primary Style Pins A B B A B A B 1-3 1-3 1-3 1-3 1-3 1-3 1-3 5 T6 Dip or SMD F 10 T6 Dip or SMD G 15 16-Pin SMD E 15 16-Pin SMD C 15 16-Pin SMD D tested in a 75 ohm system. 1-5 1-5 1-3/9-11 14-16/6-8 14-16/6-8 Dimensions in Inches (mm) .315 (8.00) 6-Pin DIP: T-13102 & T-13103 .315 (8.00) .285 (7.24) MAX. MAX. .205 (5.21) MAX. .012 .120 (0.30) (3.05) TYP. .050 (1.27) TYP. .020 (0.51) 6-Pin SMD: T-13100 T-13101 T-13104 & T-13105 .008 R (0.20) MIN. .100 (2.54) .200 (5.08) MAX. .010 (0.25) .010 (0.25) .300 (7.62) .365 (9.27) .270 (6.86) MAX. .038 (0.96) TYP. TYP. TYP. .425 (10.80) .405 (10.29) TYP. SMD versions available on Tape & Reel MAX. TYP. .286 (7.27) .020 (0.38) .100 (2.54) TYP. TYP. T6 : T-13108 & T-13109 Schematic "F" T-13108 Schematic "G" T-13109 .350 (8.89) .500 (12.70) MAX. MAX. G6 : T-13108G & T-13109G .410 (10.41) .410 (10.41) MAX. MAX. .250 (6.35) .260 (6.60) MAX. .340 (8.64) MIN. TYP. Schematic "C" P/N T-15101 Schematic "D" P/N T-15102 (7.62) MAX. .120 (3.05) .100 (2.54) MAX. .300 .080 (2.03) .400 (10.16) .020 DIA. (0.51) .020 (0.51) .100 (2.54) TYP. TYP. .040 (1.02) .010 (0.25) TYP. TYP. .510 (12.95) .480 (12.19) TYP. .285 (7.24) .505 (12.83) Schematic "E" P/N T-15100 MAX. MAX. .205 (5.21) MAX. .016 (0.41) TYP. Specifications subject to change without notice. Rhombus Industries Inc. For other values & Custom Designs, contact factory. 11 .050 (1.27) TYP. .015 (0.38) TYP. .025 (0.64) TYP. .010 (0.25) TYP. .380 (9.65) .360 (9.14) T3-2A - 4/99 15801 Chemical Lane, Huntington Beach, CA 92649-1595 Tel: (714) 898-0960 • Fax: (714) 896-0971