ABC ESR1006150ML

SPECIFICATION FOR APPROVAL
REF :
PAGE: 1
PROD.
NAME
ABC'S DWG NO.
SMD POWER INDUCTOR
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅰ﹒CONFIGURATION & DIMENSIONS:
B
A :
10.0 ± 0.4
m/m
B :
9.0 ± 0.4
m/m
C :
5.4 ± 0.4
m/m
D :
2.1 ref.
m/m
G :
2.5 ref.
m/m
H :
9.5 ref.
m/m
I :
10.0 ref.
m/m
C
100
A
H
D
G
I
( PCB Pattern )
Ⅱ﹒SCHEMATIC DIAGRAM:
a
b
Ⅲ﹒MATERIALS:
a﹒Core:Ferrite DR core
b﹒Wire :Enamelled copper wire (Class F & H)
c
Peak Temp:245±5℃
Max time above 200℃ :60sec max.
c﹒Terminal: Ag/Ni/Sn
d﹒Remark:Products comply with RoHS'
requirements
Temperature ( ℃ )
c﹒Resistance to solder heat:245±5℃.10 secs.
Preheat Area
Reflow Area
Forced Cooling Area
+4.0℃ / sec max.
150 ~ 200℃ / 60 ~ 120sec
+2.0 ~ 4.0℃
/ sec max.
-(1.0 ~ 5.0)℃ / sec max.
Peak Temp erature:
245±5℃
250
Ⅳ﹒GENERAL SPECIFICATION:
a﹒Storage temp.:-40℃ ----+125℃
b﹒Operating temp.:-40℃----+105℃
Temperature
Rising Area
200
150
60sec max.
100
50
0
AR-001A
50
100
150
200
250
SPECIFICATION FOR APPROVAL
REF :
PAGE: 2
PROD.
ABC'S DWG NO.
SMD POWER INDUCTOR
NAME
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅴ﹒ELECTRICAL CHARACTERISITCS:
DWG No.
Inductance
( μH )
ESR1006100ML□ -□□□
ESR1006120ML□ -□□□
ESR1006150ML□ -□□□
ESR1006180ML□ -□□□
ESR1006220ML□ -□□□
ESR1006270ML□ -□□□
ESR1006330ML□ -□□□
ESR1006390ML□ -□□□
ESR1006470KL□ -□□□
ESR1006560KL□ -□□□
ESR1006680KL□ -□□□
ESR1006820KL□ -□□□
ESR1006101KL□ -□□□
ESR1006121KL□ -□□□
ESR1006151KL□ -□□□
ESR1006181KL□ -□□□
ESR1006221KL□ -□□□
ESR1006271KL□ -□□□
ESR1006331KL□ -□□□
ESR1006391KL□ -□□□
ESR1006471KL□ -□□□
ESR1006561KL□ -□□□
ESR1006681KL□ -□□□
ESR1006821KL□ -□□□
10±20%
12±20%
15±20%
18±20%
22±20%
27±20%
33±20%
39±20%
47±10%
56±10%
68±10%
82±10%
100±10%
120±10%
150±10%
180±10%
220±10%
270±10%
330±10%
390±10%
470±10%
560±10%
680±10%
820±10%
1). □:Packaging information… A:Bulk
2)."-
□□□ ":Reference code
RDC
( mΩ )
typ.
max.
34.2
36.9
43.6
60.7
68.3
87.6
96.9
111.0
126.0
141.0
176.0
201.0
262.0
301.0
350.0
457.0
524.0
711.0
814.0
923.0
1056.0
1359.0
1559.0
1805.0
Rated Current
(A)
SRF
(MHz)
ref.
2.60
2.45
2.30
2.15
2.00
1.80
1.50
1.40
1.30
1.20
1.10
1.00
0.97
0.90
0.80
0.75
0.70
0.60
0.55
0.50
0.45
0.40
0.30
0.25
25.0
23.0
19.8
19.3
16.0
13.3
12.1
12.0
11.0
10.2
9.4
8.8
7.3
6.6
6.6
6.1
5.3
4.3
4.3
3.3
3.3
3.3
2.8
2.2
60
70
80
90
100
110
120
140
170
190
220
250
350
400
470
630
730
970
1150
1300
1480
1900
2250
2550
B:Taping Reel
3). Inductance test condition :10uH~82uH at 1MHz/1V
100uH~820uH at 1KHz/1V
4). Rated current: The DC current at which the inductance decreases to 90% of
it's initial value or when Δt=40℃,whichever is lower(Ta=20℃)
AR-001A
SPECIFICATION FOR APPROVAL
REF :
PAGE: 3
PROD.
ABC'S DWG NO.
SMD POWER INDUCTOR
NAME
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅵ﹒INDUCTANCE VS. DC CURRENT CURVE:
( 1 ) Configuration
T
Cover tape
N
B
A
2.0±0.5
∮C
∮C
D
G
Embossed carrier
※Carrier tape width : D
P:12 m/m
4 m/m
End
Start
100
100
Leader
no component
350 m/m min.
100
100
100
100
Trailer
no component
400 m/m min.
Components
User direction of feed
( 2 ) Dimensions
Unit:m/m
Style
A
13 - 24
330
B
21±0.8
C
13±0.5
D
24
G
26
+0
N
50
-0
T
30.4
( 3 ) Q'TY & G.W. Per package
Inner : Reel
Outer : Carton
Series
ESR1006
AR-001A
Q'TY (pcs)
G.W. (gw)
800
1,800
Style
13 - 24
Q'TY (pcs)
3,200
G.W. (Kg)
9.5
Size (cm)
40 x 40 x 24
SPECIFICATION FOR APPROVAL
REF :
PAGE: 4
PROD.
ABC'S DWG NO.
SMD POWER INDUCTOR
NAME
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅶ﹒PACKAGING INFORMATION:
E
S
R
1
0
0
6
Reference code
Appendix code 2 : Package
Appendix code 1 : Classification
Tolerance code
Electrical code
Dimension code
Type code
E : Economy
Appendix code 1:Product Classification
L:Lead Free Standard products comply with RoHS' requirements
1 ~ 9:Lead Free Special products comply with RoHS' requirements
Appendix code 2:Package Information
Code
AR-001A
Inner package
A
T.B.D.
B
T / R ( Reel package )
Inner package Q'TY
T.B.D.
800
pcs
Remark
SPECIFICATION FOR APPROVAL
REF :
PAGE: 5
PROD.
ABC'S DWG NO.
SMD POWER INDUCTOR
NAME
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅶ﹒DWGING NUMBER EXPRESSION:
Test item
Solderability
Thermal shock test
( Temp. cycle )
Specification
Test condition
More than 95% of the
terminal electrode
Shall be covered
With fresh solder.
Preheat : 155℃ / 4 hours.
Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent
Solder temp. : 235±5℃
Flux : Rosin
Dip time : 5±0.5 seconds
Electrical oharacteristics shall
not change more
than ±20%
Room temp.
15 minutes
-40 ℃
30 minutes
Room temp.
15 minutes
+105 ℃
Total : 50 cycles
Humidity Test
Temperature : 40±2℃
Humidity : 90±5%
Time : 1000 hours
High temp.
Resistance test
Temperature : 105±5℃
Applied current : Per spec.
Time : 96 hours
AR-001A
30 minutes
SPECIFICATION FOR APPROVAL
REF :
PAGE: 6
PROD.
NAME
ABC'S DWG NO.
SMD POWER INDUCTOR
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
Ⅸ﹒RELIABILITY TEST:
OBMW2
Magnet Wire-Component
September 8, 2000
E174837
JUNG SHING WIRE CO LTD
231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN
HSIEN TAIWAN
Mtl
Dsg
AIW
CFUEWB
EIAIW
EILOCKY
EILOCKW
EIW
EIW-2
FL.EILOCKY
LSFFW
LSUEW
PEW
PEY
SF.FLW
SF.EIW
[email protected]
[email protected]
SF.BLOCKBS
SF.EILOCKY#
SF.EILOCKBS
[email protected]
SFFW
Mark
Dsg
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
BC
Polyamideimide
Polyurethane
Polyesterimide
Polyesterimide
Polyesterimide
Polyesterimide
Polyesterimide
Modified Polyester
Polyurethane
Polyurethane
Polyester
Polyester
Modified Polyester
Polyesterimide
Modified Polyester
Modified Polyester
Modified
Polyester
Polyesterimide
Polyesterimide
Mtl
Dsg
OC
____
____
Polyamideimide
Polyamide
Modified
Epoxy
____
____
Polyamide
____
____
____
____Nylon
____
Nylon
Nylon
Modified
Polyamide
Polyamide
Modified
Polyamide
____
Modified Polyester
Polyurethane
ANSI
Type
Temp
Class
MW81-C
MW75C
MW35C
___
___
220
130
200
180
200
___
MW74-C
___
MW79-C
___
___
MW24-C
MW26C
MW77C
MW27-C
MW27-C
___
___
___
Mark
Dsg
____
____
____
____
____
____
BC
Coat Typ
MW26C
MW79
155
155
A not-for-profit organization
dedicated to public safety and
comm itted to quality service
OC
Polyamide
____
____
____
Polyurethane
Polyurethane
Polyurethane
Polyurethane
Polyurethane
Polyurethane
220
200
155
155
130
155
155
155
180
155
155
155
180
180
Page 1 of 2
287806002
SFFY
UEW-1
UEW-2
UEW-4
UEY
UEY-2
Coat Typ
Nylon
Polyamide
ANSI
Type
Temp
Class
MW80C
MW2-C
___
155
105
130
130
130
130
MW75C
MW28-C
MW28-C
@-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI.
LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall.
or 榮星電線 , material designation or marked designation on packaed or reel, and
Marking: Company name or trademarks
Recognized Component Mark.
See General Information Preceding These Recognitions
For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc.
287806002
AR-001A
Page 2 of 2
OBMW2⁄E174837
September 8 , 2000
SPECIFICATION FOR APPROVAL
PAGE: 7
REF :
PROD.
NAME
ABC'S DWG NO.
SMD POWER INDUCTOR
OBMW2
Magnet Wire-Comporent
ESR1006□□□□L□-□□□
ABC'S ITEM NO.
October 06, 2005
ELEKTRISOLA (MALAYSLA) SDN BHD
JALAN DAMAI SATU JANDA BAIK 28750 BENTONG, PAHANG
DARUL MAKMUR MALAYSIA
Coating Type
Mtl Dsg
Mark Dsg
BC
Estersol 180
E180
Amldester 200
Polysol-N 155
A200
PN155
Polyesterimide
(solderable)
Polyesterimide
Polyurechane
Polysol 155
P155, G155
Polyurechane
Polysol 155g
Polysol 155p
Polysol 160
Polysol 180
Pg155
Pp155,Gp155
P160
P180,G180
Polyurechane
Polyurechane
Polyurechane
Polyurechane
Polysol 170
Polysol-N 180
Polysol P155p
P170 or G170
PN180
P155p
Polyurechane
Polyurechane
OC
____
____
Nylon
____
____
____
____
____
____
Nylon
____
ANSI
Typ
E143312
Temp
Class
MW-77
180
MW-74
MW-80,
MW-28
MW-79,
MW-75
MW-75
MW-79
MW-79
MW-82
MW-79
MW-79
MW-83
MW-79
200
155,
130
155,
130
130
155
155
180
155
155
180
155
Marking:Company name, material designation or marked designation and factory identification on package ok reel
See General Information preceding These Recognitions
For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc.
AR-001A