SPECIFICATION FOR APPROVAL REF: 20090406-B ABC'S DWG NO. PROD. SMD LINE FILTER NAME PAGE: 1 SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒MECHANICAL DIMENSIONS： A B C A B C D E F G H I 2 D 1 : : : : : : : : : m/m m/m m/m m/m m/m m/m m/m m/m m/m 3.20±0.2 1.60±0.2 1.90±0.2 0.60 typ. 0.60 typ. 1.90 ref. 0.80 ref. 0.46 ref. 0.80 ref. F G E H 3 E I 4 I D G ( PCB Pattem ) Ⅱ﹒SCHEMATIC DIAGRAM： N1 1 2 4 3 N2 a b Ⅲ﹒MATERIALS LIST： a﹒Core：Ferrite b﹒Wire ：Enamelled copper wire ( class F ) c c﹒Terminal： Ag / Ni / Sn Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. d﹒Remark：Products comply with RoHS' requirements Ⅳ﹒GENERAL SPECIFICATION： c﹒Storage temp.：-40℃ ----+125℃ d﹒Operating temp.：-40℃----+125℃ （Temp. rise included） AR-001A 1 50 ~ 200 ℃ / 60 ~ 120 sec Reflow Area +2.0 ~ 4.0 ℃ / sec max. Forced Coo lin g Area -(1 .0 ~ 5 .0 )℃ / sec max. Peak Temperature: 260℃ 50s ec max. Temperature ( ℃ ) & △ L/L0A=20% max. Prehe at Area +4.0 ℃ / sec max. 250 a﹒Temp rise ：20℃ max b﹒Rated current：Base on temp. rise Tempe ra tu re Risin g Area 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF: 20090406-B PAGE: 2 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS ： Dwg. No. SF3216900YL□ -□□□ SF3216121YL□ -□□□ SF3216161YL□ -□□□ SF3216221YL□ -□□□ SF3216261YL□ -□□□ SF3216601YL□ -□□□ SF3216102YL□ -□□□ SF3216222YL□ -□□□ Impedance (Ω) @ 100 MHz 90±25% 120±25% 160±25% 220±25% 260±25% 600±25% 1000±25% 2200±25% Rated ( DC ) V 50 50 50 50 50 50 50 50 Withstanding ( DC ) V 125 125 125 125 125 125 125 125 1). □：Packaging information… A：Bulk B：Taping Reel 2)﹒"- □□□ ":Reference code 3). Impedance Test Instrument：HP4291A. 4). RDC Test Instrument：CH-502AC. 5). IDC Test Instrument：CH1062+CH301A. AR-001A Insulation Resistance ( MΩ ) min. 10 10 10 10 10 10 10 10 RDC (Ω) max. 0.300 0.300 0.400 0.400 0.500 0.800 1.000 1.200 IDC ( mA ) max. 370 370 340 320 310 260 230 200 SPECIFICATION FOR APPROVAL REF: 20090406-B PAGE: 3 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒INSERTION LOSS Vs. FREQUENCY & IMPEDANCE Vs. FREQUENCY ： Normal Mode Common Mode CH1 ︱Z︱ 10000 T & B 3.5 kΩ, 1Ω 222 1000 601 161 102 261 100 121 900 221 121 10 900 161 221 261 601 102 1 ↑ 222 0.1 1 OSC 150mV START 1 MHz Common Mode AR-001A 10 100 1000 BIAS OFF STOP 1.0 GHz Normal Mode SPECIFICATION FOR APPROVAL PAGE: 4 REF: 20090406-B ABC'S DWG NO. PROD. SMD LINE FILTER NAME SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 D ∮C ∮C G Embossed Carrier ※Carrier Tape Width : D 4 m/m P:4 m/m Start End Leader no component 200 m/m min. Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 07 - 08 178 B 21±0.8 C D 13 8 G 14 +0 N 50 -0 T 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SF3216 AR-001A Outer : Carton Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) SIZE (cm) 2,000 95 07 - 08 100,000 6.50 41 x 39 x 22 SPECIFICATION FOR APPROVAL REF: 20090406-B PAGE: 5 PROD. ABC'S DWG NO. SMD LINE FILTER NAME SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒DWGING NUMBER EXPRESSION： S F 3 2 1 6 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 2000 pcs Remark SPECIFICATION FOR APPROVAL REF: 20090406-B PAGE: 6 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒RELIABILITY TEST： 1-1.Environmental Performance No Item 1-1-1 Temperature Cycle Test Method Specification Appearance: No Damage Impedance: within±20% of initial value One cycle: Step Temperature (℃) 1 -25±3 2 25±2 3 85±3 4 25±2 Total: 5 cycles Time (min) 30 3 30 3 Measured After Exposure in The Room Condition For 1hrs 1-1-2 Humidity Resistance Temperature: 40±2℃ Relative Humidity: 90 ~ 95% Time: 100hrs Measured After Exposure In The Room Condition For 1hrs 1-1-3 High Temperature Resistance Temperature: 85±3℃ Time: 50Hrs Measured After Exposure In The Room Condition For 1Hrs 1-1-4 Low Temperature Resistance Temperature: -25±3℃ Time: 50Hrs Measured After Exposure In The Room Condition For 1Hrs 1-1-5 High Temperature Load Life There should be no evidence of short or open circle 1-1-6 Humidity Load Life 1-2.Mechanical Performance No Item 1-2-1 Resistance To Soldering Heat Specification Appearance: No Damage 1-2-2 Solder ability The Electrodes Shall Be At Least 90% Covered with New Solder Coating 1-2-3 Commponent Adhesion (Push Test) 2 Lbs AR-001A Temperature: 85±3℃ Load: Allowed DC Current Time: 500Hrs Temperature: 40±2℃ Relative Humidity: 90~95% Load: Allowed DC Current Time: 500Hrs Test Method 1. The Device Should Be Reflow soldered on PCB (peak 260℃±5℃ For 10 Seconds) 2. Solder Composition: Sn/Ag3.0/Cu0.5 3. Test Time: 6 minutes 1. Pre-Heating: 150℃,1min. 2. Solder Composition: Sn/Ag3.0/Cu0.5 3. Solder Temperature: 245±5℃. 4. Immersion Time: 4±1 sec. The device should be reflow soldered (230±5℃ For 10 seconds) to a tinned copper substrate. A force guauge should be applied to the side of the component. The device must withstand a minimum force of 2 pounds without a failure of the termination attached to component SPECIFICATION FOR APPROVAL REF: 20090406-B PAGE: 7 PROD. NAME ABC'S DWG NO. SMD LINE FILTER SF3216□□□□L□-□□□ ABC'S ITEM NO. Ⅹ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ Polyamideimide Polyamide Modified Epoxy ____ ____ Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane 287806002 Mtl Dsg Coat Typ E174837 ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ 180 180 MW26C MW79 ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 155 155 A not-for-profit organization dedicated to public safety and com mitted to quality service Page 1 of 2 Mark Dsg ____ 220 200 155 155 130 155 155 155 180 155 155 155 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed b y LZ, EL o r LZI. LZ - Sign ifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Compan y name or trademarks Recognized Compon ent Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding Th ese Recogn itions For use only in equip ment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000