ABC SF6018181YL

SPECIFICATION FOR APPROVAL
REF :
PAGE: 1
PROD.
ABC'S DWG NO.
SMD LINE FILTER
NAME
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅰ﹒CONFIGURATION & DIMENSIONS:
4
1
3
3
1
A
B
A :
B :
C :
E :
F :
G :
Wψ :
m/m
m/m
m/m
m/m
m/m
m/m
m/m
G
C
3
2
6.50 max.
3.60±0.15
1.65±0.15
2.50±0.10
4.80±0.20
0.20 min.
1.00±0.2
F
4.80
Ⅱ﹒SCHEMATIC DIAGRAM:
1.80
2.50
E
Wψ
(PCB Pattern Suggestion)
N1
1
4
2
3
N2
"
" :Polarity
Ⅲ﹒MATERIALS:
c
a﹒Core:Ferrite core
b﹒Wire:Enamelled copper wire
c﹒Base: DAP 9100F base
d﹒Terminal: Cu / Ni /Sn
Ni plating 1.5 um min.
Sn plating 7 um min. after soldering
a
b
d
Peak Temp :260 ℃ max.
Max time above 230℃ :50sec max.
Max time above 200℃ :70sec max.
e﹒Remark:Products comply with RoHS'
requirements
Temperature
Rising Area
Preheat Area
+4.0℃ / sec max.
150 ~ 200℃ / 60 ~ 120sec
Reflow Area
+2.0 ~ 4.0℃
Forced Cooling Area
-(1.0 ~ 5.0)℃ / sec max.
Peak Temperature:
260℃
250
Ⅳ﹒GENERAL SPECIFICATION:
a﹒ Temp. rise :40℃ max. at rated current
b﹒Storage temp.:-40℃ ----+120℃
c﹒Operating temp.:-40℃----+125℃
(included Temp. rise)
d﹒ Resistance to solder heat:260℃.10 secs.
AE-001A
Temperature ( ℃ )
50sec max.
230℃
200
150
70sec max.
100
50
0
50
100
150
Time ( seconds )
200
250
SPECIFICATION FOR APPROVAL
REF :
PAGE: 2
PROD.
ABC'S DWG NO.
SMD LINE FILTER
NAME
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅴ﹒ELECTRICAL CHARACTERISTICS :
DWG No.
L(µH)
20mV/10kHz
|L-L|
(µH max.)
RDC(N1=N2)
( Ω max. )
Impedance
HI-POT
Test
Freq. range
MHz
min(Ω)
SF6018100YL□ -□□□
10±50%
1.0
0.24
350~570
600
SF6018470YL□ -□□□
47±50%
4.0
0.16
4~1600
140
SF6018820YL□ -□□□
82±50%
4.0
0.20
3~850
220
SF6018101YL□ -□□□
100±50%
8.0
0.22
3~660
260
SF6018181YL□ -□□□
180±50%
8.0
0.25
3~250
500
SF6018221YL□ -□□□
220±50%
10
0.28
3~210
600
SF6018331YL□ -□□□
330±50%
10
0.30
3~120
900
250 Vac
60 Hz
3 mA
1 min.
1). □:Packaging information … A:Bulk B:Taping Reel
2)."":Reference code
3). Test equipment : Inductance ( HP4284A, 20mV/ 10kHz )
RDC ( CH-502AC )
Impedance ( E4991A )
4). Nominal voltage : 60Vdc
5). Rated current : 300 mA ( Base on series both winding.)
□□□
Impedance CURVE
10000
Measuring Circuit :
331
221
1000
100
181
Z (Ω)typ.
101
820
470
100
RF Impedance
Analyzer
10
0.1
1
10
Frequency (MHz)
AE-001A
100
1000
SPECIFICATION FOR APPROVAL
PAGE: 3
REF :
PROD.
ABC'S DWG NO.
SMD LINE FILTER
NAME
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅵ﹒PACKAGING INFORMATION
( 1 ) Configuration
T
Cover Tape
N
A
B
2.0±0.5
∮C
∮C
D
G
Embossed Carrier
※ Carrier tape width : D
P:8m/m
4m/m
End
Start
0
0
1
0
0
1
0
0
1
0
0
1
0
0
1
Leader
no component
200 m/m min.
Trailer
no component
400 m/m min.
Components
User direction of feed
( 2 ) Dimensions
Unit:m/m
Style
A
07 - 12
178
B
21±0.8
C
D
13
12
N
G
14
+0
50
T
-0
18.4
( 3 ) Q'TY & G.W. Per package
Inner : Reel
Series
SF6018
AE-001A
Q'TY (pcs)
G.W. (gw)
1000
300
Outer : Carton
Style
07 - 12
Q'TY (pcs)
40,000
G.W. (Kg)
12.0
Size (cm)
42 x 41 x 24
SPECIFICATION FOR APPROVAL
REF :
PAGE: 4
PROD.
ABC'S DWG NO.
SMD LINE FILTER
NAME
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅷ﹒DWGING NUMBER EXPRESSION:
S
F
6
0
1
8
Reference code
Appendix code 2 : Package
Appendix code 1 : Classification
Tolerance code
Electrical code
Dimension code
Type code
Appendix code 1: Product Classification
L:Lead Free Standard products comply with RoHS' requirements
1 ~ 9 :Lead Free Special products comply with RoHS' requirements
Appendix code 2:Package Information
Code
AE-001A
Inner package
A
T.B.D.
B
T / R ( Reel package )
Inner package Q'TY
T.B.D.
1000
pcs
Remark
SPECIFICATION FOR APPROVAL
PAGE: 5
REF :
PROD.
SMD LINE FILTER
NAME
ABC'S DWG NO.
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅷ﹒ RELIABILITY TEST:
Test item
Solderability
Thermal shock test
( Temp. cycle )
Specification
Test condition
More than 90% of the
terminal electrode
Shall be covered
With fresh solder.
Preheat : 150±25℃ for 60 seconds
Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent
Solder temp. : 260±5℃
Flux : Rosin
Dip time : 4±1 seconds
Inductance shall
not change more
than ±20%
Room temp.
15 minutes
-25±2 ℃
30 minutes
Room temp.
15 minutes
85±2 ℃
Total : 50 cycles
Humidity
Resistance test
High temp.
Resistance test
AE-001A
Temperature : 40±2℃
Humidity : 90 ~ 95%
Applied current : Per spec.
Time : 500 hours
Temperature : 80±2℃
Applied current : Per spec.
Time : 500 hours
30 minutes
SPECIFICATION FOR APPROVAL
PAGE: 6
REF :
PROD.
ABC'S DWG NO.
SMD LINE FILTER
NAME
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Ⅸ﹒ DWG EXPRESSION:
OBMW2
Magnet Wire-Component
September 8, 2000
JUNG SHING WIRE CO LTD
231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN
HSIEN TAIWAN
Mtl
Dsg
AIW
CFUEWB
EIAIW
EILOCKY
EILOCKW
EIW
EIW-2
FL.EILOCKY
LSFFW
LSUEW
PEW
PEY
SF.FLW
SF.EIW
[email protected]
[email protected]
SF.BLOCKBS
SF.EILOCKY#
SF.EILOCKBS
[email protected]
SFFW
Mark
Dsg
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
____
BC
Polyamideimide
Polyurethane
Polyesterimide
Polyesterimide
Polyesterimide
Polyesterimide
Polyesterimide
Modified Polyester
Polyurethane
Polyurethane
Polyester
Polyester
Modified Polyester
Polyesterimide
Modified Polyester
Modified Polyester
Modified
Polyester
Polyesterimide
Polyesterimide
SFFY
UEW-1
UEW-2
UEW-4
UEY
UEY-2
OC
____
____
Polyamideimide
Polyamide
Modified
Epoxy
____
____
Polyamide
____
____
____
____Nylon
____
Nylon
Nylon
Modified
Polyamide
Polyamide
Modified
Polyamide
____
Modified Polyester
Polyurethane
ANSI
Type
Temp
Class
MW81-C
MW75C
MW35C
___
___
220
130
200
180
200
___
MW74-C
___
MW79-C
___
___
MW24-C
MW26C
MW77C
MW27-C
MW27-C
___
___
___
Mark
Dsg
____
____
____
____
____
____
BC
Coat Typ
Polyurethane
Polyurethane
Polyurethane
Polyurethane
Polyurethane
Polyurethane
220
200
155
155
130
155
155
155
180
155
155
155
180
180
MW26C
MW79
155
155
A not-for-profit organization
dedicated to public safety and
committed to quality service
Page 1 of 2
287806002
Mtl
Dsg
Coat Typ
E174837
OC
Polyamide
____
____
____
Nylon
Polyamide
ANSI
Type
Temp
Class
MW80C
MW2-C
___
155
105
130
130
130
130
MW75C
MW28-C
MW28-C
@-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI.
LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall.
Marking: Company name or trademarks
or 榮星電線 , material designation or marked designation on packaed or reel, and
Recognized Component Mark.
See General Information Preceding These Recognitions
For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc.
287806002
AE-001A
Page 2 of 2
OBMW2⁄E174837
September 8 , 2000
SPECIFICATION FOR APPROVAL
REF :
PAGE: 7
PROD.
NAME
ABC'S DWG NO.
SMD LINE FILTER
SF6018□□□□L□-□□□
ABC'S ITEM NO.
Friday , October 24, 2003
QMFZ2 Component - Plastics
E150608
WAH HONG INDUSTRIAL CORP
10TH FL 235 CHUNG CHENG 4TH RD KAOHSIUNG TAIWAN
Material Designation:
Product Description: Diallyl Phthalate ( DAP ), molding compound, furnished as pellets.
Color
Min. Thick. (m/m)
HWI HAI
Flame
Class
RTI RTI
RTI
Elec Imp
Str
BK
0.37
V-0
0
3
130
130
130
BK
0.82
V-0
2
0
130
130
130
CTI: 0
HVTR: 0
D495: 4
IEC GWIT
IEC GWFI
IEC Ball Pressure (℃): -
Dielectric Strength (kV/m/m): -
Volume Resistivity (10 xohm-cm): -
Dimensional Stability (%): -
ISO Tensile Strength (MPa): -
ISO Flexural Strength (MPa): -
ISO Tensile Impact (kJ/m 2 ): -
ISO Heat Deflection (℃): -
ISO Izod Impact (kJ/m2 ): -
ISO Charpy Impact (kJ/m2 ): -
Report Date: 8/18/1998
Underwriters Laboratories Inc R
UL94 small-scale test data does not pertain to building materials, furnishings and related contents.
UL 94 small-scale test data is intended solely for determining the flammability of plastic materials used in components
and parts of end-product devices and appliances, where the acceptability of the combination is determined by ULI.
AE-001A