Power Switch 0.5A 125V AC Qualified Type SDKN Series Compact and low-profile for primary/secondary switching with compatibility to low level rating. Detector Push Slide Rotary Encoders Power Dual-in-line Package Type Product Line Circuit arrangement Rating SPDT 0.5A 125V AC 0.25A 250V AC 5mA 5V DC Total travel （mm） Operating force 9 3.5±1N Mounting Operation Minimum order method type unit（pcs.） Push Snap-in 9.7 Drawing No. SDKNA20600 1 SDKNA20700 2 1,250 Lever 2±1.5N Product No. TACT SwitchTM CustomProducts Notes 1. Safety standard approval must be obtained as a set. 2. Please place purchase orders per minimum orders units(integer). Dimensions Unit:mm No. Style Mounting hole dimensions Push Type Rocker Type Push 25 Slide Type 11.3 15 Rotary Type 22.9 Within the ON range of the C-1 circuit Total travel position 10.8 7.9 4.2 Within the OFF range of the C-2 circuit Direction of insertion t R 12.5 min. 14.4 min. 1.7 t=0.8-1.5mm 15 2 15.75 1 6.5 11.2 6 R1 7.3 13 Terminal No.1 11 Terminal No.2 Terminal No.C 215 Power Switch 0.5A 125V AC Qualified Type SDKN Series Dimensions Unit:mm No. Style Mounting hole dimensions 25 Lever 11.3 15 Detector Push 11 Within the OFF range of the C-2 circuit 11.2 1.7 R Direction of insertion t Encoders 14.1 min. 15.5 5.5 3 2 2 12.2 min. R1 8 1.8 0. 1.7 R Total travel position 5.1 Slide Rotary 22.9 Within the ON range of the C-1 circuit t=0.8-1.5mm 15 Power Dual-in-line Package Type Terminal No.1 11 Terminal No.2 Terminal No.C TACT SwitchTM CustomProducts Note Connector corresponds to [HLP-03V], manufactured by the J.S.T. Mfg. Co., Ltd. Circuit Diagram SPDT C 2 Push Type Rocker Type 1 Note Verify the performance under actual product conditions before use. Slide Type Rotary Type Cautions 1. This product does not have a water-proof or drip-proof construction. Prevent ingress of water into the switch. Avoid using around spilt or flowing. It may cause deterioration of the insulation. 2. Do not apply load on the connecter or lead wire（code）attached to the product. Using the product with load applied on the connecter/lead wire might cause terminal wobble or contact failures. 3. ON/OFF signal reading（For DC ratings） Shall be considered when designing circuit and software as follows. （1）Setting of thresh voltage A 4V or larger voltage difference between switch ON and OFF is recommended. Thresh voltage should be set to the center. 4V min. Thresh voltage 0V （2）ON/OFF signal reading ON/OFF signal reading intervals should be at a minimum of 50ms with at least 3 repetitions. Reading of micro-computer Times 1 2 3 50ms min. 216 Power Switches List of Varieties Series Items Rocker Push Type SDKN SDKS SDKR SDKQ SDDJE ※1 ※2 SDDJF ※1 ※2 Detector Photo Push Slide Travel （mm） 9 9.7 14.6 2.5 1.5 Rating Electrical performance Contact resistance 5.2 Rotary Water-proof type Remark Operating temperature range 3.5 –20℃ to ＋60℃ –30℃ to ＋60℃ 0.25A 250V AC 2A 250V AC 0.5A 125V AC 4A 125V AC 5mA 5V DC –10℃ to ＋60℃ –10℃ to ＋85℃ 3A 125V AC 0.5A 250V AC 1A 125V AC 100mΩ max. 50mΩ max. Encoders –10℃ to ＋55℃ Power 16（6）/250∼ 6A/96A 250V∼ Dual-in-line Package Type TACT SwitchTM 100mΩ max. CustomProducts Mechanical performance Insulation resistance 500MΩ min. 500V DC Voltage proof 1,000V AC for 1minute Terminal strength 50N 70N for 1minute for 1minute Operating Actuator direction strength Perpendicular direction 100MΩ min. 500V DC 500MΩ min. 500V DC 1,500V AC for 1minute 20N 5N for 1minute ― 20N 20N 25N Rocker Type Durability 12,000cycles Load : as ratings Environmental performance –40±2℃ for 96h 60N for 1minute Push Type Operating life –30±2℃ for 96h 10N for 1minute 25N Manual Resistance to soldering soldering heat Dip soldering Cold 2,000V AC for 1minute 100N 30N 6,000cycles 1,000V AC for 1minute –25±2℃ for 240h Slide Type 300±10℃, 3±0.5s 350±10℃, 3±0.5s 260±5℃, 10±1s ※260±10℃, 10±1s 100,000cycles 10,000cycles Refer to individual product spec. Load : as ratings –20±2℃ for 240h –20±2℃ for 96h Dry heat 85±2℃ for 96h 85±2℃ for 240h 85±2℃ for 96h Damp heat 40±2℃, 90 to 95%RH for 96h 60±2℃, 40±2℃, 90 to 95%RH for 240h 90 to 95%RH for 1000h 40±2℃, 90 to 95%RH for 96h Page 215 217 219 220 221 Rotary Type 225 ● Power Switches Cautions ……………………………………………………………………………………………………235 ● Power Switches Safety Standard ………………………………………………………………………………237, 238, 239 Notes 1. ※1. Dip soldering can be used on SDDJE For PC board terminal and SDDJF right angle terminal types only. 2. ※2. The operating temperature range for automotive applications can be raised upon request. Please contact us for requirements of this kind. 213