15” Industrial Panel PC
supports Pentium 4 CPU, OSD,
Function Keys & one PCI Slot
•15” TFT Panel•
•BS-669 VGA to Panel Transfer Card•
•HPCI-2SP Backplane•
•180W Power Supply•
Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of
this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does it
make any commitment to update the information contained herein.
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are mentioned
for identification purposes only, and may be trademarks and/or registered trademarks
of their respective companies or owners.
© Copyright 2004 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.1, July 01, 2005
Table of Contents
Chapter 1 Introduction……………………………….1
Major Features ...................................................2
Specifications ....................................................3
Panel Specifications ..........................................3
Power Supply Specifications............................4
Control Keys ......................................................4
Dimensions ........................................................5
Chapter 2 Unpacking…………………………………7
Opening the Delivery Package .........................7
Chapter 3 Hardware Installation…………………….9
Chapter 4 Touch Screen Driver Installation……….13
Touch Screen Driver Installation....................13
Driver Functions ..............................................18
Safety Instructions
The safety recommendations outlined in this section are to be read,
understood and followed before operating the product. Keep this
information in a safe place for future reference. Failure to comply with
any of the following safety procedures could result in serious hazard.
Do not operate product for any purposes other than its intended use.
This product is intended for indoor use only.
Do not operate product if power cord is damaged in anyway.
Do not insert objects into openings.
Do not immerse product in water or permit liquids to spill inside.
Turn off power when unattended or not in use. Unplug product before moving it or
when it is not in use for an extended period of time. The socket-outlet should be
installed near the equipment and should be easily accessible.
Do not alter or extend electric plug. Plug is configured for appropriate electrical
Do not overload electrical outlets beyond their capacity as this can result in a fire.
Life Expectancy of Constituent Parts
This section describes the life expectancy of constituent parts (backlight,
power supply, internal cooling fan and touch screen) of which the BPC-6670
is made up .
TFT Display Backlight
Display brightness decreases over time with use. The expected operating lifetime
of the backlight time to reach 50% initial brightness is 30,000 hours (assuming
continuous lit state at 25 degrees C). Actual lifetime before replacement is about
30,000 hours, although this depends on operating conditions.
Power Supply
The power supply has a minimum predicted MTBF of 100,000 hours of
continuous operation at 25 degrees C, maximum-output load, and nominal AC
input voltage.
Internal Cooling Fan
The BPC-6670 is equipped with two built-in +12V cooling fans, the life expectancy
of this fan under continuous use is approximately 50,000 hours (average time
before the rate of rotation is reduced by approximately 30%). Although the rate of
rotation will continue to go down, the fan should not just suddenly stop.
Touch Screen
The operating lifetime of the touch screen is approximately 1 million operations
(as tested by mechanical manipulation under 100g of force at a rate of two
presses per second).
This page intentionally left blank.
Chapter 1
The BPC-6670 is a 15” industrial Panel PC built around the Intel®
Pentium® 4 CPU with clock rate 2.4GHz/2.8GHz and 400MHz
FSB/533MHz FSB. The rear design of BPC-6670 enhances the
disassembly process when required. It also supports various mounting
solutions like wallmount, or desktop for different applications.
The BPC-6670 has a 15” display and an optional touch screen that
operate under all types of working environments. It offers OSD (On
Screen Display) and Function Keys (optional) on the front panel for
user’s operation.
The BPC-6670 supports Pentium® 4 industrial PICMG Bus SBC. It also
comes with a reliable power supply and two 4cm high efficient cooling
fans to enhance system stability.
The Intel® 82540EM Gigabit Ethernet Controller architecture is
optimized to deliver both high performance and PCI Bus efficiency with
the lowest power and smallest die size. Using state logic design with a
pipelined DMA Unit and 128-bit wide buses for the fastest
performance, the Intel® 82540EM controller handles Gigabit Ethernet
traffic with low network latency and minimal internal processing
The combination 82562 device with ICH2/3/4 LAN solution is a 32-bit
PCI device that features enhanced scatter-gather bus mastering
capabilities which allow the LAN solution to perform high-speed data
transfers over the PCI Bus. The Bus mastering capabilities enable the
LAN solution to process high-level commands and perform operations,
thereby offloading communications tasks from the system CPU.
Other features included in this 15-inch TFT panel are the BS-669 VGA
to Panel transfer card supporting OSD function, Function Keys
(optional), a 15-inch resistive touch screen (optional), one PCI
expansion slot, two DDR sockets supporting up to 2GB (optional), two
serial ports, one parallel port, one USB connector, Award PnP Flash
BIOS, and more.
The BPC-6670 is compatible and can draw from a large body of
hardware and software resources worldwide.
180W power supply with NEMKO, IEC, UL, CE, CSA, TUV approvals
User can select the operating system he wants to use just like an
ordinary personal computer. An operating system such an MS-DOS,
Windows can be selected to suit the application.
Keyboard-less operations are possible through the use of a touch
screen. In addition to a watchdog timer indispensable in FA
applications, you can select from a broad range of variations to arrive
at the optimum configuration for your application and budget.
Major Features
The BPC-6670 comes with the following features:
Aluminum chassis
15” high brightness TFT color panel display
Provides Pentium 4 CPU, OSD function
Provides HS-7001 PICMG Bus SBC, Function Keys (optional)
Built-in BS-669, HPCI-2SP backplane, 180W power supply
Intel 82845G display controller
Intel 82540EM (or Intel 82551) and Intel 82562 LAN controller
Two COM, one parallel, one USB connector
One PCI expansion slot
One 2.5”/3.5” HDD, one 3.5” FDD and one slim CD-ROM spaces
Two 4cm ball bearing cooling fans
Supports 15” Touch Screen (optional)
System Board: HS-7001 industrial PICMG Bus SBC (optional)
CPU: PGA 478 for Intel Pentium 4 up to 2.4GHz (400MHz FSB)/
2.8GHz (533MHz FSB) CPU
Memory: Two DDR sockets supporting up to 2GB (optional)
Backplane: HPCI-2SP backplane
PCI Slot: One PCI expansion slot
OSD: BS-669 VGA to Panel transfer card, supporting OSD function
Function Keys: Provides Function Keys in the front panel (optional)
Touch Screen: 15” resistive Touch Screen (optional)
VGA: Intel 82845G with 1MB or 8MB memory supporting up to 1280 x
1024 at 32-bit colors
LAN: Intel 82540EM 100/1000 Based (or Intel 82551 10/100 Based)
and Intel 82562 10/100 Based LAN
HDD/FDD/CD-ROM: One 2.5”/3.5” HDD, one 3.5” FDD and one slim
CD-ROM spaces
Serial Port: Two serial ports
Parallel: One enhanced bi-directional parallel port supporting
USB: One USB connector
Keyboard/Mouse: PS/2 6-pin Mini DIN
BIOS: Award PnP Flash BIOS
Watchdog Timer: Software programmable time-out intervals from
1~256 sec.
Fan: Two 4cm ball bearing cooling fans
Power Supply: 180W power supply
Temperature: 0~50°C (operating); -20~+60°C (storage)
Dimensions: 43.0 x 32.1 x 9.32 cm
Panel Specifications
Screen Size: 15 inches
Display Format: 1024 x 768 pixels
Pixel Pitch: 0.3075(H) x 0.3075(V) m/m
Color: 262K
Brightness: 250 cd/m2
Contrast Ratio: 200:1
MTBF: 30,000 hrs.
Power Supply Specifications
Input Voltage: 100~240VAC full range
Input Frequency: 47~63Hz
Input Current: 4A max. 115Vrms at 60Hz; 2A max. 230Vrms at 50Hz
Inrush Current: 50A cold, 80A ware at 132VAC
Hold Up Time: 17ms min. at full load & nominal input voltage
Output Power: +3.3V and +5V total output should not exceed 61W
Power Good Signal: Turn on delay 100~500ms
Thermal System: One 4cm ball bearing cooling fan
Dimensions: 15.0 x 8.15 x 4.05 cm
Control Keys
BPC-6171 provides Function Keys and OSD Control Keys.
Function Keys Define (optional)
OSD Control Keys Define (optional)
Menu: Menu/Item select
Down: Cursor down control
Up: Cursor up control
Return: Return to menu
This page intentionally left blank.
Chapter 2
Opening the Delivery Package
The BPC-6670 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
After unpacking the Panel PC, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The BPC-6670 delivery package
contains the following items:
BPC-6670 Panel PC x 1
Power Cable x 1
Touch Screen Drive Diskette x 1 (optional)
Drive CD Disk x 1
SBC Manual x 1
User’s Manual x 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
This page intentionally left blank.
Chapter 3
Hardware Installation
This chapter tells how to install components into the Panel PC system.
For the external interface, please refer to SBC’s manual.
Dismount the rear cover by loosening the screws in accordance
with the picture.
Remove the 3-in-1 drive bay in accordance with the picture.
The 3.5-inch FDD (or the 3.5-inch HDD) is installed on top of the
3-in-1 drive bay.
NOTE: Only one of the two choices can be used.
Secure the CD-ROM on the 3-in-1 drive bay after fastening it onto
a transfer card.
Fasten the 2.5-inch HDD onto the 3-in-1 drive bay.
The fully-equipped, 3-in-1 drive bay is placed on the BPC-6670
by means of screw.
Finally, screw back the rear cover.
Chapter 4
Touch Screen Driver Installation
This chapter contains the detailed information of Touch Screen driver
installation procedures. The utility disk that come with the delivery
package contains an auto-run program that invokes the installation
programs for the Touch Screen driver. The following sections describe
the installation procedures of driver based on Win 2000 operating
systems. It is recommended that you install the drivers matching the
sections listed in this chapter.
Touch Screen Driver Installation
4.1.1 Installing Touch Screen Driver in Win 95 and 98
Insert Utility CD Disk into your CD ROM drive. The main menu will
pop up as shown below.
The screen displays copying “installation wizard” and “PenMount
Utilities Installation” screen plus “welcome” message appear,
click “Next”.
The next screen is “Software License Agreement”, select “I
accept” and click “Next”.
The next screen is “Ready to Install the Program”, click “Install”.
Once the Install Shield Wizard finishes updating your system, it
will prompt you to restart the computer. Click “Finish” to exit the
4.1.2 Installing Touch Screen Driver in Win 2000
Insert Utility CD Disk into your CD ROM drive. The main menu will
pop up as shown below.
The screen displays copying “installation wizard” and “PenMount
Utilities Installation” screen plus “welcome” message appear,
click “Next”.
The next screen is “Software License Agreement”, select “I
accept” and click “Next”.
The next screen is “Ready to Install the Program”, click “Install”.
Once the Install Shield Wizard finishes updating your system, it
will prompt you to restart the computer. Click “Finish” to exit the
4.2 Driver Functions
4.2.1 PenMount Control Panel
To adjust the display with touch screen, click “Calibration” and
follow the calibrate point to do calibration, there are five points on
screen for calibration.
Test or demonstrate PenMount touch screen operation. Also the
touch location is shown on the display. Click on touch “DRAW” to
About Penmount
It shows information about PenMount controller and this driver.
4.2.2 PenMount Monitor
The PenMount monitor icon is shown in the menu bar of Windows 2000
system when the PenMount monitor is turned on under the PenMount
There are several functions on the PenMount monitor:
Right Click Button
When selecting this function, there is a mouse icon shown in the
right-button place of screen. It shows ‘left button’ being as default
for normal use. Touch this mouse icon to change the next touch to
be ‘Right Button’ function. After one touch, the mouse icon will
change to ‘Left Button’ automatically. If user needs to use right
button again, user has to touch the mouse icon again for changing
the button function.
Turn on or off beep sound.
Close the PenMount Monitor function.