CADEKA SPT7820BCS

SPT7820
10-BIT, 20 MSPS, TTL OUTPUT, A/D CONVERTER
FEATURES
APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
Monolithic 20 MSPS Converter
On-Chip Track/Hold
Bipolar ±2.0 V Analog Input
60 dB SNR @ 1 MHz Input
Low Power (1.0 W Typical)
5 pF Input Capacitance
TTL Outputs
Medical Imaging
Professional Video
Radar Receivers
Instrumentation
Electronic Warfare
Digital Communications
GENERAL DESCRIPTION
The SPT7820 A/D converter is a 10-bit monolithic converter
capable of word rates of a minimum of 20 MSPS. On board
track/hold function assures excellent dynamic performance
without the need for external components. Drive requirement problems are minimized with an input capacitance of
only 5 pF.
Inputs and outputs are TTL compatible to interface with TTL
logic systems. An overrange output signal is provided to
indicate overflow conditions. Output data format is straight
binary. Power dissipation is very low at only 1.0 watt with
power supply voltages of +5.0 and -5.2 volts. The SPT7820
also provides a wide input voltage swing of ±2.0 volts.
The SPT7820 is available in 28-lead ceramic sidebrazed DIP,
PDIP and SOIC packages over the commercial, industrial
and military temperature ranges. Contact the factory for
availability of die and /883 versions.
BLOCK DIAGRAM
Coarse
A/D
4
Analog
Prescaler
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
AAAAAAAAAAAAAAA
T/H Amplifier
Bank
Successive Interpolation
Stage i
Successive Interpolation
Stage i+1
Successive Interpolation
Stage N
Decoding Network
Analog
Input
Digital
Output
10
ABSOLUTE MAXIMUM RATINGS (Beyond which damage may occur)1 25 °C
Supply Voltages
VCC ........................................................................... +6 V
VEE ........................................................................... -6 V
Output
Digital Outputs ......................................... +30 to -30 mA
Temperature
Operating Temperature ............................ -55 to +125 °C
Junction Temperature1 .............................................. +175 °C
Lead Temperature, (soldering 10 seconds) ........ +300 °C
Storage Temperature ................................ -65 to +150 °C
Input Voltages
Analog Input ............................................... VFB≤VIN≤VFT
VFT, VFB .............................................................. +3.0 V, -3.0 V
Reference Ladder Current ..................................... 12 mA
CLK Input .................................................................. VCC
Note:
1. Operation at any Absolute Maximum Rating is not implied. See Electrical Specifications for proper nominal
applied conditions in typical applications.
ELECTRICAL SPECIFICATIONS
TA=Tmin - Tmax, VCC=+5.0 V, VEE=-5.2 V, DVCC=+5.0 V, VIN=±2.0 V, VSB=-2.0 V, VST=+2.0 V, fCLK=20 MHz, 50% clock duty cycle, unless otherwise
specified.
PARAMETERS
TEST
CONDITIONS
TEST
LEVEL
Resolution
DC Accuracy (+25 °C)
Integral Nonlinearity
Differential Nonlinearity
No Missing Codes
Analog Input
Input Voltage Range
Input Bias Current
Input Bias Current
Input Resistance
Input Resistance
Input Capacitance
Input Bandwidth
+FS Error
-FS Error
Reference Input
Reference Ladder Resistance
Reference Ladder Tempco
Timing Characteristics
Maximum Conversion Rate
Overvoltage Recovery Time
Pipeline Delay (Latency)
Output Delay
Aperture Delay Time
Aperture Jitter Time
Acquisition Time
MIN
SPT7820A
TYP
MAX
10
±Full Scale
100 kHz Sample Rate
VIN=0 V
TA=-55 to +125 °C
TA=-55 to +125 °C
3 dB Small Signal
SPT7820B
TYP MAX UNITS
10
V
V
VI
±1.0
±0.5
Guaranteed
V
VI
IV
VI
IV
V
V
V
V
±2.0
30
fCLK=1 MHz
MIN
Bits
±1.5
±0.75
Guaranteed
±2.0
30
100
75
300
300
5
120
±2.0
±2.0
100
75
300
300
5
120
±2.0
±2.0
V
60 µA
75 µA
kΩ
kΩ
pF
MHz
LSB
LSB
VI
V
500
800
0.8
500
800
0.8
Ω
Ω/°C
VI
V
IV
V
V
V
V
20
20
MHz
ns
14
1
5
20
1 Clock Cycle
18 ns
ns
ps-RMS
ns
8.7
8.3
7.0
Bits
Bits
Bits
60
75
fCLK=1 MHz
TA=+25 °C
TA=+25 °C
TA=+25 °C
TA=+25 °C
LSB
LSB
Dynamic Performance
Effective Number of Bits
fIN=1 MHz
fIN=3.58 MHz
fIN=10.0 MHz
20
20
14
1
5
20
9.2
8.8
7.5
1
18
Typical thermal impedances (unsoldered, in free air): 28L sidebrazed DIP: θja = 50 °C/W, 28L plastic DIP: θja = 50 °C/W,
28L SOIC: θja = 100 °C/W.
SPT7820
2
3/11/97
ELECTRICAL SPECIFICATIONS
TA=Tmin - Tmax, VCC=+5.0 V, VEE=-5.2 V, DVCC=+5.0 V, VIN=±2.0 V, VSB=-2.0 V, VST=+2.0 V, fCLK=20 MHz, 50% clock duty cycle, unless otherwise
specified.
PARAMETERS
Dynamic Performance
Signal-To-Noise Ratio
(Without Harmonics)
fIN=1 MHz
fIN=3.58 MHz
fIN=10.0 MHz
Harmonic Distortion
fIN=1 MHz
fIN=3.58 MHz
fIN=10.0 MHz
TEST
CONDITIONS
Power Supply Requirements
Voltages VCC
DVCC
-VEE
Currents ICC
DICC
-IEE
Power Dissipation
Power Supply Rejection
SPT7820A
TYP
MAX
MIN
SPT7820B
TYP MAX
UNITS
I
IV
IV
I
IV
IV
I
IV
IV
57
55
52
56
54
52
50
47
43
60
58
55
58
56
54
53
50
46
54
52
49
53
51
49
47
44
40
57
55
52
55
53
51
49
46
42
dB
dB
dB
dB
dB
dB
dB
dB
dB
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
TA=+25 °C
TA=0-70, -25 to +85 °)
TA=-55 to +125 °C*
I
IV
IV
I
IV
IV
I
IV
IV
57
54
50
56
53
50
46
45
45
60
57
53
58
55
52
48
47
47
54
51
47
53
50
47
43
42
42
57
54
50
55
52
49
45
44
44
dB
dB
dB
dB
dB
dB
dB
dB
dB
I
IV
IV
I
IV
IV
I
IV
IV
V
V
V
55
52
48
54
51
48
44
43
41
57
52
49
45
51
48
45
41
40
38
54
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
VI
VI
I
I
IV
IV
2.4
VI
VI
2.4
IV
IV
IV
I
I
I
I
V
4.75
4.75
-4.95
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
fIN=3.58 MHz
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
fIN=10.0 MHz
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
Spurious Free Dynamic Range TA=+25 °C, fIN=1 MHz
Differential Phase
TA=+25 °C, fIN=3.58 & 4.35 MHz
Differential Gain
TA=+25 °C, fIN=3.58 & 4.35 MHz
Digital Outputs
Logic 1 Voltage
Logic 0 Voltage
MIN
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
TA=+25 °C
TA=0-70, -25 to +85 °C
TA=-55 to +125 °C*
Signal-to-Noise and Distortion
fIN=1 MHz
Digital Inputs
Logic 1 Voltage
Logic 0 Voltage
Maximum Input Current Low
Maximum Input Current High
Pulse Width Low (CLK)
Pulse Width High (CLK)
TEST
LEVEL
55
47
67
0.2
0.5
52
44
67
0.2
0.7
Degree
%
fCLK=1 MHz
TA=+25 °C
TA=+25 °C
0
0
20
20
+5
+5
4.5
0.8
+20
+20
300
2.4
0
0
20
20
+5
+5
4.5
0.8
+20
+20
V
V
µA
µA
ns
300 ns
fCLK=1 MHz
TA=+25 °C
TA=+25 °C
TA=+25 °C
TA=+25 °C
(5 V ±0.25 V, -5.2 ±0.25 V)
2.4
V
0.6 V
0.6
5.0
-5.2
118
40
40
1.0
1.0
5.25
5.25
-5.45
145
55
57
1.3
4.75
4.75
-4.95
5.0
-5.2
118
40
40
1.0
1.0
5.25
5.25
-5.45
145
55
57
1.3
V
V
V
mA
mA
mA
W
LSB
*Temperature tested /883 only.
SPT7820
3
3/11/97
TEST LEVEL
TEST LEVEL CODES
All electrical characteristics are subject to the
following conditions:
All parameters having min/max specifications
are guaranteed. The Test Level column indicates the specific device testing actually performed during production and Quality Assurance inspection. Any blank section in the data
column indicates that the specification is not
tested at the specified condition.
TEST PROCEDURE
I
100% production tested at the specified temperature.
II
100% production tested at TA = +25 °C, and sample
tested at the specified temperatures.
III
QA sample tested only at the specified temperatures.
IV
Parameter is guaranteed (but not tested) by design
and characterization data.
V
Parameter is a typical value for information purposes
only.
VI
100% production tested at TA = +25 °C. Parameter is
guaranteed over specified temperature range.
Figure 1A: Timing Diagram
A
A
A
A
A
A
A
CLK
Output
Data
AA
A
AA
AA AA
A
N+1
N
tpwH
A
A
N-2
A
AA
N+2
tpwL
td
N-1
Data Valid
N
Data Valid
N+1
Figure 1B: Single Event Clock
CLK
AA
AA
A
AAAAAAAAAAAA
AA
A
AAAAAAAAAAAA
A
AAAAAAAAAAAA
td
Output
Data
Data Valid
Table I - Timing Parameters
PARAMETERS
DESCRIPTION
MIN
td
CLK to Data Valid Prop Delay
tpwH
tpwL
TYP
MAX
UNITS
-
14
18
ns
CLK High Pulse Width
20
-
300
ns
CLK Low Pulse Width
20
-
-
ns
SPT7820
4
3/11/97
TYPICAL PERFORMANCE CHARACTERISTICS
THD vs Input Frequency
SNR vs Input Frequency
80
70
70
Total Harmonic Distortion (dB)
80
Signal-to-Noise Ratio (dB)
fs = 20 MSPS
60
50
40
30
20
fs = 20 MSPS
60
50
40
30
20
100
100
102
101
101
Input Frequency (MHz)
Signal-to-Noise and Distortion (dB)
SINAD vs Input Frequency
80
80
70
70
SNR, THD, SINAD (dB)
fs =20 MSPS
60
50
40
30
60
50
20
40
20
102
101
A
A
A
A
A
A
A
A
SNR, THD, SINAD vs Sample Rate
SNR, THD
SINAD
fIN = 1 MHz
30
100
102
Input Frequency (MHz)
100
Input Frequency (MHz)
101
102
Sample Rate (MSPS)
SNR, THD, SINAD vs Temperature
Spectral Response
65
0
fS = 20 MSPS
fIN = 1 MHz
SNR
SNR
SNR, THD, SINAD (dB)
60
Amplitude (dB)
-30
-60
-90
THD
THD
55
SINAD
50
fS = 20 MSPS
fIN = 1 MHz
45
-120
40
0
1
2
3
4
5
6
7
8
9
10
Input Frequency (MHz)
-25
0
+25
+50
+75
Temperature (°C)
SPT7820
5
3/11/97
TYPICAL INTERFACE CIRCUIT
device. The use of ground planes is recommended to achieve
optimum device performance. DGND is needed for the DVCC
return path (40 mA typical) and for the return path for all digital
output logic interfaces. AGND and DGND should be separated from each other and connected together only at the
device through a ferrite bead.
The SPT7820 requires few external components to achieve
the stated operation and performance. Figure 2 shows the
typical interface requirements when using the SPT7820 in
normal circuit operation. The following section provides a
description of the pin functions and outlines critical performance criteria to consider for achieving the optimal device
performance.
A Schottky or hot carrier diode connected between AGND
and VEE is required. The use of separate power supplies
between VCC and DVCC is not recommended due to potential
power supply sequencing latch-up conditions. Using the
recommended interface circuit shown in figure 2 will provide
optimum device performance for the SPT7820.
POWER SUPPLIES AND GROUNDING
The SPT7820 requires -5.2 V and +5 V analog supply
voltages. The +5 V supply is common to analog VCC and
digital DVCC. A ferrite bead in series with each supply line is
intended to reduce the transient noise injected into the
analog VCC. These beads should be connected as closely as
possible to the device. The connection between the beads
and the SPT7820 should not be shared with any other
device. Each power supply pin should be bypassed as
closely as possible to the device. Use 0.1 µF for VEE and
VCC, and 0.01 µF for DVCC (chip caps are preferred).
VOLTAGE REFERENCE
The SPT7820 requires the use of two voltage references:
VFT and VFB. VFT is the force for the top of the voltage
reference ladder (+2.5 V typ), VFB (-2.5 V typ) is the force for
the bottom of the voltage reference ladder. Both voltages are
applied across an internal reference ladder resistance of
800 Ω. The +2.5 V voltage source for reference VFT must be
current limited to 20 mA maximum if a different driving circuit
is used in place of the recommended reference circuit shown
in figures 2 and 3. In addition, there are three reference
AGND and DGND are the two grounds available on the
SPT7820. These two internal grounds are isolated on the
Figure 2 - Typical Interface Circuit
R1
CLK
CLK
100 Ω
± 2.5 V Max
VIN
6
5
+
10 kΩ
Trim
1 µF
C2
.01 µF
30 kΩ
2R
C3
.01 µF
+ IC2
OP-07
8
+5 V
- 5.2 V
2R
D7
D6
D5
D4
D3
D2
4
D1
.01 µF
30 kΩ
C4
.01 µF
2R
D0 (LSB)
VSB
SUCCESSIVE
INTERPOLATION
STAGE # N
7
R
6
-2.5 V
1 µF
+
C5
.01 µF
VFB
VEE
.01 µF
D8
C6
.1 µF
C8
C7
.1 µF
C9
DGND
1
10 kΩ
2
SUCCESSIVE
INTERPOLATION
STAGE # 1
2R
VRM
DGND
3
ANALOG
PRESCALER
R
VST
DVCC
GND
VFT
C1
.01 µF
DVCC
4
+2.5 V
VOUT
(REF-03)
D9 (MSB)
VCC
IC1
VIN
AGND
+
AGND
C19
1 µF
VEE
+5V
D10 (Overrange)
D I G IT A L O U
2
4
COARSE
A/D
VCC
VIN
(±2 V)
DECODING NETWORK
(TTL)
C10
.01 µF
C11
.01 µF
Notes to prevent latch-up due to power sequencing:
FB
FB
FB
1)
D1 = Schottky or hot carrier diode, P/N IN5817.
D1
2)
FB = Ferrite bead, Fair Rite P/N 2743001111
10 µF
to be mounted as close to the device as possible. The ferrite bead to the
ADC connection should not be shared with any other device.
3)
C1-C11 = Chip cap (recommended) mounted as close to the device's pin
as possible.
4)
Use of a separate supply for VCC and DVCC is not recommended.
-5.2 V
(Analog)
5)
R1 provides current limiting to 45 mA.
6)
C6, C7, C8 and C9 should be ten times larger than C10 and C11.
7)
C8 = C9 = a 0.1 µF cap in parallel with a 4.7 µF cap.
10 µF
+
AGND
+
+5 V
(Analog)
DGND
SPT7820
6
3/11/97
ladder taps (VST, VRM and VSB). VST is the sense for the top
of the reference ladder (+2.0 V), VRM is the midpoint of the
ladder (0.0 V typ) and VSB is the sense for the bottom of the
reference ladder (-2.0 V). The voltages seen at VST and VSB
are the true full scale input voltages of the device when VFT
and VFB are driven to the recommended voltages (+2.5 V and
-2.5 V typical respectively). These points should be used to
monitor the actual full scale input voltage of the device and
should not be driven to the expected ideal values as is
commonly done with standard flash converters. When not
being used, a decoupling capacitor of .01 µF (chip cap
preferred) connected to AGND from each tap is recommended to minimize high frequency noise injection.
ANALOG INPUT
VIN is the analog input. The full scale input range will be 80%
of the reference voltage or ±2 volts with VFB=-2.5 V and
VFT=+2.5 V.
The drive requirements for the analog inputs are minimal
when compared to conventional Flash converters due to the
SPT7820’s extremely low input capacitance of only 5 pF and
very high input resistance of 300 kΩ. For example, for an
input signal of ±2 V p-p with an input frequency of 10 MHz,
the peak output current required for the driving circuit is only
628 µA.
Figure 3 - Analog Equivalent Input Circuit
CLOCK INPUT
VCC
Analog Prescaler
VIN
A
A
A
A
A
The SPT7820 is driven from a single-ended TTL input (CLK).
The CLK pulse width (tpwH) must be kept between 20 ns and
300 ns to ensure proper operation of the internal track-andhold amplifier. (See timing diagram.) When operating the
SPT7820 at sampling rates above 3 MSPS, it is recommended that the clock input duty cycle be kept at 50% but
performance will not be degraded if kept within the range of
40-60%. The analog input signal is latched on the rising edge
of the CLK.
VFT
A
A
The clock input must be driven from fast TTL logic (VIH
≤4.5 V, TRISE <6 ns). In the event the clock is driven from a
high current source, use a 100 Ω resistor in series to current
limit to approximately 45 mA.
VEE
An example of a reference driver circuit recommended is
shown in figure 2. IC1 is REF-03, the +2.5 V reference with a
tolerance of 0.6% or +/- 0.015 V. The potentiometer R1 is
10 kΩ and supports a minimum adjustable range of up to
150 mV. IC2 is recommended to be an OP-07 or equivalent
device. R2 and R3 must be matched to within 0.1% with good
TC tracking to maintain a 0.3 LSB matching between VFT and
VFB. If 0.1% matching is not met, then potentiometer R4 can
be used to adjust the VFB voltage to the desired level. VFT and
VFB should be adjusted such that VST and VSB are exactly
+2.0 V and -2.0 V respectively.
DIGITAL OUTPUTS
The format of the output data (D0-D9) is straight binary. (See
table II.) The outputs are latched on the rising edge of CLK
with a propagation delay of 14 ns (typ). There is a one clock
cycle latency between CLK and the valid output data. (See
the timing diagram.)
Table II - Output Data Information
The analog input range will scale proportionally with respect
to the reference voltage if a different input range is required.
The maximum scaling factor for device operation is ± 20% of
the recommended reference voltages of VFT and VFB. However, because the device is laser trimmed to optimize performance with ± 2.5 V references, the accuracy of the device will
degrade if operated beyond a ± 2% range.
ANALOG INPUT
OVERRANGE
D1O
OUTPUT CODE
D9-DO
>+2.0 V + 1/2 LSB
+2.0 V -1 LSB
1
O
11 1111
11 1111
0.0 V
-2.0 V +1 LSB
O
O
ØØ ØØØØ ØØØØ
OO OOOO OOOØ
<-2.0 V
O
OO OOOO OOOO
1111
111Ø
(Ø indicates the flickering bit between logic 0 and 1).
The following errors are defined:
+FS error = top of ladder offset voltage = ∆(+FS -VST+1 LSB)
-FS error = bottom of ladder offset voltage = ∆(-FS -VSB -1 LSB)
where the +FS (full scale) input voltage is defined as the output
transition between 1-10 and 1-11 and the -FS input voltage is
defined as the output transition between 0-00 and 0-01.
The rise times and fall times of the digital outputs are not
symmetrical. The propagation delay of the rise time is typically 14 ns and the fall time is typically 6 ns. (See figure 4.)
The nonsymmetrical rise and fall times create approximately
8 ns of invalid data.
SPT7820
7
3/11/97
Figure 4 - Digital Output Characteristics
N
CLK In
N+1
2.4 V
Rise Time
6 nsec
6 ns
typ.
3.5 V
Data Out
(Actual)
2.4 V
AAA
AAA
AAA
AAA
AAA
(N-2)
0.8 V
0.5 V
Data Out
(Equivalent)
Invalid
Data
(N-1)
tpd1
(14 ns typ.)
(N-2)
Invalid
Data
(N-1)
AA
AA
AA
AA
AA
Invalid
Data
Invalid
Data
(N)
(N-1)
OVERRANGE OUTPUT
EVALUATION BOARD
The OVERRANGE OUTPUT (D10) is an indication that the
analog input signal has exceeded the positive full scale input
voltage by 1 LSB. When this condition occurs, D10 will switch
to logic 1. All other data outputs (D0 to D9) will remain at
logic 1 as long as D10 remains at logic 1. This feature makes
it possible to include the SPT7820 into higher resolution
systems.
The EB7820 evaluation board is available to aid designers in
demonstrating the full performance of the SPT7820. This
board includes a reference circuit, clock driver circuit, output
data latches and an on-board reconstruction of the digital
data. An application note describing the operation of this
board as well as information on the testing of the SPT7820 is
also available. Contact the factory for price and availability.
SPT7820
8
3/11/97
PACKAGE OUTLINES
28-Lead Sidebrazed
28
MILLIMETERS
MIN
MAX
SYMBOL
A
0.077
0.093
1.96
2.36
0.016
0.095
J
B
C
D
E
F
G
H
I
J
0.020
0.105
.050 typ
0.060
0.235
1.412
0.605
0.012
0.620
0.41
2.41
0.00
1.02
5.46
35.26
14.86
0.23
15.24
0.51
2.67
1.27
1.52
5.97
35.86
15.37
0.30
15.75
I
1
INCHES
MIN
MAX
H
G
A
0.040
0.215
1.388
0.585
0.009
0.600
E
F
C
B
D
28-Lead Plastic DIP
K
28
SYMBOL
A
I
1
J
H
G
A
B
F
C
D
INCHES
MIN
MAX
B
C
D
E
F
G
H
I
J
K
MILLIMETERS
MIN
MAX
0.200
0.120
0.170
0.135
0.020
0.100
0.067
0.013
0.180
0.622
0.555
1.460
0.085
5.08
3.05
4.32
3.43
0.51
2.54
1.70
0.33
4.57
15.80
14.10
37.08
2.16
E
SPT7820
9
3/11/97
PACKAGE OUTLINES
28-Lead SOIC
SYMBOL
28
I H
INCHES
MIN
MAX
MILLIMETERS
MIN
MAX
A
B
C
0.696
0.004
0.712
0.012
.050 typ
17.68
0.10
0.00
18.08
0.30
1.27
D
E
F
0.014
0.009
0.080
0.019
0.012
0.100
0.36
0.23
2.03
0.48
0.30
2.54
G
H
I
0.016
0.394
0.291
0.050
0.419
0.299
0.41
10.01
7.39
1.27
10.64
7.59
1
A
F
B
C
D
G
E
SPT7820
10
3/11/97
PIN ASSIGNMENTS
PIN FUNCTIONS
DGND
1
28
D0
2
27
V
D1
3
26
AGND
D2
4
25
V
D3
5
24
V
D4
6
23
V
SB
D5
7
22
V
DVCC
DIP/PDIP/SOIC
FB
RM
21
V
D7
9
20
V
ST
D8
10
19
V
D10
18
V
DGND
Digital Ground
D0-D9
TTL Outputs (D0=LSB)
D10
TTL Output Overrange
CLK
Clock
VEE
-5.2 V Supply (Analog)
AGND
Analog Ground
VCC
+5.0 V supply (Analog)
VIN
Analog Input
DVCC
Digital +5.0 V Supply
VRM
Middle of Voltage Reference Ladder
VFT
Force for Top of Reference Ladder
VST
Sense for Top of Reference Ladder
VFB
Force for Bottom of Reference Ladder
VSB
Sense for Bottom of Reference Ladder
CC
8
11
Function
EE
D6
D9
Name
IN
FT
CC
12
17
DGND
13
16
V
DV
CC
14
15
CLK
AGND
EE
ORDERING INFORMATION
PART NUMBER
TEMPERATURE RANGE
PACKAGE TYPE
SPT7820AIJ
-25 to +85 °C
28L Sidebrazed DIP
SPT7820BIJ
SPT7820ACN
SPT7820BCN
-25 to +85 °C
0 to +70 °C
0 to +70 °C
28L Sidebrazed DIP
28L Plastic DIP
28L Plastic DIP
SPT7820ACS
0 to +70 °C
28L SOIC
SPT7820BCS
SPT7820AMJ
SPT7820BMJ
0 to +70 °C
-55 to +125 °C
-55 to +125 °C
28L SOIC
28L Sidebrazed DIP
28L Sidebrazed DIP
SPT7820
11
3/11/97