CHENMKO ENTERPRISE CO.,LTD CHUMB6PT SURFACE MOUNT Dual Digital Silicon Transistor VOLTAGE 50 Volts CURRENT 30 mAmpere APPLICATION * Switching circuit, Inverter, Interface circuit, Driver circuit. FEATURE * Small surface mounting type. (SC-88/SOT-363) * High current gain. * Suitable for high packing density. * * * * SC-88/SOT-363 Low colloector-emitter saturation. High saturation current capability. tow CHDTA144E chips in apackage. Built in bias resistor(R1=47kΩ, Typ. ) (1) (6) 0.65 1.2~1.4 2.0~2.2 0.65 (4) 0.15~0.35 (3) 1.15~1.35 0.8~1.1 0.08~0.15 0~0.1 0.1 Min. CIRCUIT 6 4 2.15~2.45 R1 R2 R2 R1 1 3 SC-88/SOT-363 Dimensions in millimeters LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCC Supply voltage − -50 V VIN Input voltage -40 +10 V − -30 − -100 − 150 mW IO DC Output current IC(Max.) Tamb ≤ 25 OC, Note 1 mA PTOT Total power dissipation TSTG Storage temperature −55 +150 O C TJ Junction temperature − 150 O C Note 1. Transistor mounted on an FR4 printed-circuit board. 2004-04 RATING CHARACTERISTIC ( CHUMB6PT ) CHARACTERISTICS Tamb = 25 °C unless otherwise speciÞed. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIoff) Input off voltage IO=-100uA; VCC=-5.0V -0.5 − Input on voltage IO=-2mA; VO=-0.3V − − − -3.0 V VI(on) VO(on) Output voltage IO=-10mA; II=-0.5mA − -0.1 -0.3 V II Input current VI=-5V − − -0.18 mA IC(off) Output current VI=0V; VCC=-50V − − -0.5 uA hFE DC current gain IO=-5mA; VO=-5.0V 68 − − R1 Input resistor 32.9 47 61.1 KΩ R2/R1 fT Resistor ratio Transition frequency 0.8 − 1.0 250 1.2 − MHz Note 1.Pulse test: tp≤300uS; δ≤0.02. IC=-5mA, VCE=-10.0V f =100MHz V RATING CHARACTERISTIC CURVES ( CHUMB6PT) Typical Electrical Characteristics Fig.1 Input voltage vs. output current (ON characteristics) -100 Fig.2 Output current vs. input voltage (OFF characteristics) -10m VCC =- 5V -5m VO=- 0.3V OUTPUT CURRENT : Io (A) INPUT VOLTAGE : VI(on) (V) -50 -20 -10 -5 Ta =- 40OC O 25 = C 100OC -2 -1 -500m -200m -100m -100 -200 -500 -1m -2m -2m -1m -500 -200 -100 -50 -20 -10 -5 -2 -1 -0 -5m -10m -20m -50m -100m Ta=100OC 25OC -40 OC -0.5 Fig.3 DC current gain vs. output current -1 VO =- 5V -2.5 -3.0 lO/lI=20 -500m OUTPUT VOLTAGE : VO(on) (V) DC CURRENT GAIN : GI 100 -2.0 Fig.4 Output voltage vs. output current 500 200 -1.5 INPUT VOLTAGE : VI(off) (V) OUTPUT CURRENT : IO (A) 1k -1.0 Ta=100OC 25OC -40OC 50 20 10 5 2 1 -100 -200 O -200m Ta=100 C 25OC -40 OC -100m -50m -20m -10m -5m -2m -500 -1m -2m -5m -10m -20m -50m -100m OUTPUT CURRENT : IO (A) -1m -100 -200 -500 -1m -2m -5m -10m -20m -50m -100m OUTPUT CURRENT : IO (A)