CONNOR-WINFIELD MSTM-S3-IT3

MSTM-S3-IT3-19.44M
Stratum 3
Timing Module
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Bulletin
Page
Revision
Date
Issued By
TM034
1 of 16
P01
04 DEC 02
MBatts
Application
Features
The Connor-Winfield MSTM-S3-IT3
Simplified Control Timing Module acts as a
complete system clock module for Stratum 3
timing applications in accordance with GR1244, Issue 2 and GR-253, Issue 3.
Connor Winfield’s Stratum 3 timing modules
helps reduce the cost of your design by
minimizing your development time and
maximizing your control of the system clock
with our simplified design.
• -40° to 85° Temp.
Range
• 5V Miniature Timing
Module
• Redundant 8kHz
References
• 40 sec., Filtered,
Hold Over History
• Operational Status
Flags
General Description
Functional Block Diagram
The Connor-Winfield Stratum 3 Simplified Control Timing
Module acts as a complete system clock module for general
Stratum 3 timing applications.
Full external control input allows for selection and monitoring
of any of four possible operating states: 1) Holdover, 2) External
Reference #1, 3) External Reference #2, and 4) Free Run. Table
#1 illustrates the control signal inputs and corresponding operational states.
In the absence of External Control Inputs (A,B), the MSTM
enters the Free Run mode and signals an External Alarm. The
MSTM will enter other operating modes upon application of a
proper control signal. Mode 1 operation (A=1, B=0) results in an
output signal that is phase locked to the External Reference
Input #1. Mode 2 operation (A=0, B=1) results in an output signal that is phase locked to External Reference Input #2. Holdover mode operation (A=1, B=1) results in an output signal at or
near the frequency as determined by the latest (last) lockedsignal input values and the holdover performance of the MSTM.
Free Run ModeFree Run mode operation (A=0, B=0) is a guaranteed output of 4.6 ppm of the nominal frequency.
Alarm signals are generated at the Alarm Output during Holdover and Free Run operation. Alarm Signals are also generated
by loss-of-lock, loss of Reference, and by a Tune-Limit indication
from the PLL. A Tune-Limit alarm signal indicates that the
OCXO tuning voltage is approaching within 10% the limits of its
lock capability and that the External Reference Input may be
erroneous. A high level indicates an alarm condition. Real-time
indication of the operational mode is available at unique operating mode outputs on pins 1-4.
Control loop 0.1 Hz filters effectively attenuate any reference
jitter, smooth out phase transients, comply with wander transfer
and jitter tolerances.
Figure 1
CNTL A
Free Run
Ref 1
Ref 2
Holdover
Mode
Control
CNTL B
PLL TVL
Free Run
Holdover
Alarm Out
Reference
Select
Ex Ref 1
LOL/LOR
Phase
Comparator
Ex Ref 2
SYNC_OUT
DAC
Filters
DAC
Tuning
Voltage
Monitor
FIFO
Stratum
3
OCXO
PLL TVL
Function Control Table
Table 1
CNTL
A
CNTL
B
Operational
Mode
0
0
1
0
External
Reference
#1
0
1
External
Reference
#2
1
1
Ref 1
Free Run (Default Mode)
Ref 2
Hold Over
Free Run
PLL_TVL
Alarm Out
0
0
0
1
0
1
Normal
Tune Limit
LOR + LOL
1
1
1
0
0
0
0
0
0
0
0
0
0
1
0
0
1
1
Normal
Tune Limit
LOR + LOL
0
0
0
1
1
1
0
0
0
0
0
0
0
1
0
0
1
1
0
0
1
0
0
1
Hold Over
Absolute Maximum Rating
Table 2
Symbol
Parameter
Minimum
Nominal
VCC
Power Supply Voltage
-0.5
7.0
Volts
1.0
VI
Input Voltage
-0.5
VCC + 0.5
Volts
1.0
Ts
Storage Temperature
-55
100
deg. C
1.0
Data Sheet #: TM034
Maximum
Page 2 of 16
Units
Rev: P01
Notes
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Recommended Operating Conditions
Table 3
Symbol
Parameter
Minimum
Nominal
Maximum
Units
Vcc
Power supply voltage
4.75
5.00
5.25
Volts
VIH
High level input voltage - TTL
2.0
VCC
Volts
VIL
Low level input voltage - TTL
0
0.8
Volts
tIN
Input signal transition - TTL
250
ns
CIN
Input capacitance
15
pF
VOH
High level output voltage,
IOH = -4.0mA, VCC = min.
5.25
Volts
VOL
Low level output voltage,
IOL = 12.0 mA, VCC = min.
0.4
Volts
tTRANS
Clock out transition time
tPULSE
8kHz input reference pulse
width( positive or negative)
30
TOP
Operating temperature
-40
2.4
4.0
Notes
2.0
ns
ns
85
°C
Specifications
Table 4
Parameter
Specifications
Frequency Range (SYNC_OUT)
19.44 MHz
Notes
Supply Current
250 mA typical, 400 mA during warm-up (Maximum)
Timing Reference Inputs
Dual 8 kHz references
Jitter, Wander and Phase Transient Tolerances
GR-1244-CORE 4.2-4.4, GR-253-CORE 5.4.4.3.6
Wander Generation
GR-1244-CORE 5.3, GR-253-CORE 5.4.4.3.2
Wander Transfer
GR-1244-CORE 5.4
Jitter Generation
GR-1244-CORE 5.5, GR-253-CORE 5.6.2.3
Jitter Transfer
GR-1244-CORE 5.5, GR-253-CORE 5.6.2.1
Phase Transients
GR-1244-CORE 5.6, GR-253-CORE 5.4.4.3.3
3.0
Free Run Accuracy
4.6 ppm over TOP
Hold Over Stability
±0.37 ppm for initial 24 hrs
Inital Offset
±0.05 ppm
Temperature
±0.28 ppm
Drift
4.0
±0.04 ppm
Maximum Hold Over History
40 seconds
Pull-in/ Hold-in Range
±4.6 ppm minimum
Lock Time
<100 sec.
PLL_TVL Alarm Limit
Extreme 10% ranges of Pull-in/Hold-in Range
NOTES:
1.0: Stresses beyond those listed under Absolute Maximum Rating may cause damage
to the device. Operation beyond Recommended Conditions is not implied.
4.0:
2.0:
Logic is 3.3V CMOS
5.0:
3.0
GR-1244-CORE 3.2.1
5.0
Hold Over stability is the cumulative fractional frequency offset as described by
GR-1244-CORE, 5.2
Pull-in Range is the maximum frequency deviation from nominal clock rate on the
reference inputs to the timing module that can be overcome to pull into synchronization
with the reference
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 3 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
Pin Description
Table 5
Pin #
Connection
Description
1
HOLD OVER
Indicator output. High output when Hold Over mode is selected by control pins.
2
REF 1
Indicator output. High output when Ref 1 mode is selected by control pins.
3
REF 2
Indicator output. High output when Ref 2 mode is selected by control pins.
4
FREE RUN
Indicator output. High output when Free Run mode is selected by control pins.
5
GND
Ground
6
ALARM _OUT
Alarm output. High output if module is in Free Run, or Hold Over, or LOR, or LOL, or
PLL_TVL mode.
7
CNTL A
Mode control input
8
CNTL B
Mode control input
9
PLL_TVL
Tuning Voltage Limit alarm output. High output when Sync_Out is near the extreme
10% ranges of the Pull-in/Hold-in range.
10
GND
Ground
11
SYNC_OUT
Primary timing output signal. Signal is sychronized to reference.
12
GND
Ground
13
N/C
Do not connect. It may affect the module adversely if a signal is apllied.
14
GND
Ground
15
EX_REF_2
External Input Reference #2
16
GND
Ground
17
EX_REF_1
External Input Reference #1
18
VCC
+5V dc supply
Typical Application
Figure 2
BITS
System
Signal
#1
MUX Y
Input Select
Timing Card #1
Line Card #1
CW’s STM/MSTM module
CW’s SCG
2500/4500
#N
S
#1
MUX Y
Clockout
RCV
Timing Card #2
Line Card #N
CW’s STM/MSTM module
CW’s SCG
2500/4500
#N
S
Clockout
RCV
System Select
Data Sheet #: TM034
Page 4 of 16
Rev: P01
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Typical Module Test Set-up
Figure 3
Vcc
5 Vdc - 18
1 - Hold Over
2 - Ref 1
Ext. Ref 1 - 17
3 - Ref 2
Gnd - 16
8 kHz
Stratum 1 Traceable
Signal
Ext. Ref 2 - 15
4 - Free Run
5 - Gnd
Gnd - 14
6 - Alarm Out
N/C - 13
7 - Cntl A
Gnd - 12
8 - Cntl B
Sync_Out - 11
Oscilloscope
Probe
10 MHz
Vcc
Stratum 1 Reference
Frequency Counter
Probe
Gnd - 10
9 - PLL_TVL
Top View
Typical System Test Set-up
Figure 4
GPS or LORAN
Timing Source
This device supplies system time
information. It can be thought of as
supplying "absolute time" reference
information
S a m p le M T IE D a t a fo r S T M -S 3 /M S T M - S 3
1 .0 E -6
Possible Choices Include
Stanford Research Model: FS700
Truetime Model XXX
T ypic al res po n s e - 3000 se c o nd te st - Jitte r a pplie d (2 U I @ 10 H z)
re f da te A P R 22 1998
k dh
M T IE (s
1 0 0 .0 E -9
10
MHz
M TIE
1 0 .0 E -9
1 2 4 4 - 5 .2 M a s k ( A )
1 2 4 4 - 5 .2 M a s k ( B )
1 2 4 4 - 5 .6 M a s k
G R2 5 3 - 5 .4 .4 .3 . 2
1 .0 E -9
1 0 0 .0 E -3
1 .0E +0
10 .0E +0
1 0 0 .0 E +0
O bs e r va tion Tim e (s )
1.0 E+ 3
1 0 .0 E +3
C o pyright 1998 C o n n o r-W in fie ld a ll righ ts re se rve d
Target System Under Test
Clock or BITS logic level
clock input (TTL, CMOS,
etc.)
Arbitrary
Waveform
Generator
[Noise
Source]
S a m p le W a n d e r G e n e r a t io n (T D E V ) f o r S T M /M S T M - S 3
1.0 E- 6
T ypica l re s po n s e - 3000 s ec o nd te st - Jitter a pplie d ( 2 UI @ 10 H z)
re f da te A P R 22 1998
k dh
1 0 0.0 E- 9
1 0.0 E- 9
TD E V (s e c
DS-1 Line Card
OC-48 Line Card
OC-3 Line Card
. . . . ...
OC-12 Line Card
MTIE, TDEV, Wander Transfer,
and Wander Generation Plots
Line Card
Noise Modulation Input
10
MHz
External
Reference
Input
Standards
Compliance
Documents
DS1 rate RZ (1.544 MHz), E1 rate RZ or 8 kHz
clock RZ with noise modulation
Timing Card
Arbitrary
Waveform
Generator
Timing Card
External
Reference
Input
T DEV
G R1 2 4 4 - F ig 5 . 1
1.0 E- 9
G R1 2 4 4 - F ig 5 - 3
1 0 0 .0 E -1 2
10 .0E -3
10 0 .0 E -3
1 .0 E +0
1 0.0 E+0
In te g r a t io n T im e ( s e c )
1 .0 E +3
Time-stamped ensemble
based on absolute time
reference (10MHz input)
10
MHz
DS1 rate [1.544 MHz] BITS Bipolar
1 00 .0E +0
C o pyrigh t 1998 C o n no r-W in fie ld alll righ ts res e rv e d
Phase Error data output
DS-1, OC-3, OC-12 electrical or optical signals
10
MHz
Tektronix
SJ300E
External
Reference
Input
HP53310A
Modulation Analyzer / Time Interval Analyzer
Wander Analyzer data (IEEE-488)
External
Reference
Input
IEEE-488 Controller
Platform for software
HP 53305A Phase Analyzer
HP E1748A Sync
Measurement
Tektronix Wander Analyzer
TEKTRONIX SJ300E
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 5 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
MSTM-S3-IT3 Typical Current Draw
Figure 5
0.4
0.38
0.36
Current (Amps)
0.34
0.32
0.3
0.28
0.26
0.24
0.22
0.2
0
10
20
30
40
50
60
Time (sec)
MSTM-S3-IT3 Typical Phase Noise Plot
Figure 6
0
-20
-40
dBc/Hz
-60
-80
-100
-120
-140
-160
-180
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Hz
Data Sheet #: TM034
Page 6 of 16
Rev: P01
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
MSTM-S3-IT3 Typical Phase Gain
Figure 7
10.00
0.00
-10.00
-20.00
Phase Gain (dB)
-30.00
-40.00
-50.00
-60.00
-70.00
-80.00
-90.00
-100.00
-110.00
0.01
0.10
1.00
10.00
100.00
1000.00
10000.00
Reference Modulation Frequency (Hz)
MSTM-S3-IT3 Typical Hold Over Stability over Temperature
Figure 8
250
Frequency Offset (ppb)
200
150
100
50
0
0
10
20
30
40
50
60
70
Temperature (C°)
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 7 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
Typical Wander Generation MTIE
Figure 9
1000
GR1244, Fig 5.2 (A)
GR1244, Fig 5.2 (B)
GR253-5.4.4.3.2, Fig 5.17
Jittered Reference
Pristine Reference
Temperature Stressed Reference
MTIE (ns)
100
10
1
0.1
1
10
100
1000
10000
100000
1000000
Observation Time (sec.)
Typical Wander Generation TDEV
Figure 10
100
GR1244, Fig 5.1
Jitte re d Re fe re nce
Pristine Re fe re nce
Te m pe ra ture S tre sse d Re fe re nce
TDEV (ns)
10
1
0.1
0.01
0.1
1
10
100
Integration Time (sec.)
Data Sheet #: TM034
Page 8 of 16
1000
Rev: P01
10000
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Typical Calibrated Wander Transfer TDEV
Figure 11
10000
TDEV (ns)
1000
100
TDEV (ns)
GR1244, Fig 5.3
10
1
0.01
0.1
1
10
100
1000
10000
Integration Time (Sec.)
Typical Reference Switch MTIE
Figure 12
10000
GR1244, Fig 5-7, Stratum 2/3E
GR1244, Fig 5-7, Stratum 3/4E
MTIE (ns)
MTIE (ns)
1000
100
10
1
0.001
0.01
0.1
1
10
100
1000
Observation Time (sec)
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 9 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
Typical Entry Into Hold Over MTIE
Figure 13
10000
MTIE (ns)
1000
100
10
1
0 .0 0 1
G R -1 2 4 4 O b je c tive , F i g . 5 -8
G R -1 2 4 4 R e q uire m e nt, F i g . 5 -8
G R -2 5 3 , F ig . 5 -1 9 , R e q uire m e nt
T yp ic a l M T IE
0 .0 1
0 .1
1
10
100
1000
O b s e rv a tio n T im e (s e c o n d s )
Typical Return from Hold Over MTIE
Figure 14
10000
MTIE (ns)
1000
100
10
G R -1 2 4 4 R e q u ire m e n t , F ig . 5 -7 M TIE (n s )
Ty p ic a l M TIE
1
0.001
0.01
0.1
1
10
100
O b se r v a ti o n T i m e (se c . )
Data Sheet #: TM034
Page 10 of 16
Rev: P01
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Typical 1us Phase Transient TIE
Figure 15
1200
1000
TIE (ns)
800
600
400
200
0
-200
0
1
2
3
4
5
6
7
8
9
10
Time (sec)
Typical Phase Transient MTIE
Figure 16
10000
MTIE (ns)
1000
G R -2 5 3 , F i g . 5 -1 9 , R e q u i r e m e n t
M T I E (n s)
100
10
1
0 .0 1
0 .1
1
10
100
1000
O b s e rv a tio n T im e (s e c )
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 11 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
MSTM-S3-IT3 Mode Indicator Delay
Figure 17
Change in
Operational Mode
Operational Mode
Indicator
∆tm
2 msec <∆ tm < 4.125 msec
Tuning Voltage Limit Alarm Timing Diagram
Figure 18
TVL Limit High
Frequency
Sync_Out
(Nominal Frequency)
TVL Limit Low
Frequency
TVL Alarm
&
Alarm Out
∆t
0 < ∆t < 2.125 msec
*The DAC is updated only when the output changes level. The maximum
update rate is 8 kHz
Data Sheet #: TM034
Page 12 of 16
Rev: P01
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Loss of Reference Timing Diagram
Figure 19
External
Reference
Input
Alarm
tAon
tAoff
2 msec < tAon < 6.125 msec
0 msec < tAoff < 2.125 msec
Solder Clearance
Figure 20
.020" MAX.
.020"
.030"
PIN LAND
ALL SOLDER AND/OR WIRE TAGS
SHALL NOT EXTEND MORE THAN .020"
BELOW PC BOARD BOTTOM SURFACE
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 13 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
MECHANICAL OUTLINE:
GROUND AND POWER SUPPLY LINES:
The mechanical outline of the MSTM-S3-IT3 is
shown in Figure 21. The board space required is 2” x
2”. The pins are .040” in diameter and are .150” in
length. The unit is spaced off the PCB by .030”
shoulders on the pins. Due to the height of the
device it is recommended to have heat sensitive
devices away where the air flow might not be
blocked.
Power specifications will vary depending primarily
on the temperature range. At wider temperature
ranges starting at 0 to 70 deg. C., an ovenized
oscillator, OCXO, will be incorporated. The turn-on
current for an OCXO requires a peak current of about
.4A for about a minute. The steady state current will
the vary from 50-150 mA depending on the
temperature. It is suggested to plan for the peak
current in the power and ground traces pin 18 and
pin 5. The other four ground pins 10, 12, 14, and 16
are intended for signal grounds.
PAD ARRAY AND PAD SPACING:
The pins are arranged in a dual-in-line
configuration as shown in Figure 21. There is .2”
space between the pins in-line and each line is
separated by 1.6”. See Figures 21 & 22 and Table
6.
PAD CONSTRUCTION:
The recommended pad construction is shown in
Figure 23. For the pin diameter of .040” a hole
diameter of .055” is suggested for ease of insertion
and rework. A pad diameter of .150” is also
suggested for support. This leaves a spacing of
.050” between the pads which is sufficient for most
signal lines to pass through.
SOLDER MASK:
A solder mask is recommended to cover most the
top pad to avoid excessive solder underneath the
shoulder of the pin to avoid rework damage. See
Table 6 and Figure 23.
VIA KEEP OUT AREA:
It is recommended that there be no vias or feed
throughs underneath the main body of the module
between the pins. It is suggested that the traces in
this area be kept to a minimum and protected by a
layer of solder mask. See Figure 22.
POWER SUPPLY REGULATION:
Good power supply regulation is recommended for
the MSTM-S3-IT3 The internal oscillators are
regulated to operate from 4.75 - 5.25 volts. Large
jumps within this range may still produce varying
degrees of wander. If the host system is subject to
large voltage jumps due to hot-swapping and the like,
it is suggested that there be some form of external
regulation such as a DC/DC converter.
SOLDERING RECOMMENDATIONS:
Due to the sensitive nature of this part, hand
soldering or wave soldering of the pins is
recommended after reflow processes.
WASHING RECOMMENDATIONS:
The MSTM-S3-IT3 is not in a hermetic enclosure.
It is recommended that the leads be hand cleaned
after soldering. Do not completely immerse the
module.
MODULE BAKEOUT:
Do not bakeout the MSTM-S3-IT3
Data Sheet #: TM034
Page 14 of 16
Rev: P01
Date: 12 / 04 / 02
© Copyright 2002 The Connor-Winfield Corp. All Rights Reserved Specifications subject to change without notice
Package Dimensions
Characteristic Measurements
Figure 21
Table 6
Characteristic Item
Measurement (inches)
Pad to Pad Spacing
0.200
Solder pad top O.D.
0.150
Solder pad top I.D.
0.055
Solder pad bottom O.D.
0.150
Solder pad bottom I.D.
0.055
Solder mask top dia.
0.070
Solder mask bottom dia.
0.155
Pin row to row spacing
1.600
Recommended Footprint Dimensions
Side Assembly View
Figure 22
Figure 23
TOP SIDE
SOLDER RESIST
(OVER PAD)
PCB
SIDE VIEW
BOTTOM SIDE
SOLDER RESIST
(UP TO PAD)
Data Sheet #: TM034
© Copyright 2002 The Connor-Winfield Corp.
Page 15 of 16
Rev: P01
Date: 12 / 04 / 02
All Rights Reserved Specifications subject to change without notice
2111 Comprehensive Drive
Aurora, Illinois 60505
Phone: 630- 851- 4722
Fax: 630- 851- 5040
www.conwin.com
Revision
Revision Date
Note
P00
12/07/01
Final Release
P01
12/04/02
Increased upper temp. range to 85° C