CONNOR-WINFIELD OVC5EE3BA

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
5V SINEWAVE OCVCXO
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
Supply Voltage
TABLE 1.0
UNITS
MINIMUM
-55
NOMINAL
-
MAXIMUM
100
UNITS
°C
(Vcc)
-0.5
-
7.0
Vdc
MINIMUM
NOMINAL
MAXIMUM
UNITS
OPERATING SPECIFICATIONS
Center Frequency
Frequency Calibration (Vc= 2.5 Vdc)
Frequency Stability
Aging: Daily
Aging: First Year
Aging: Short Term (1 second)
Operating Temperature Range
(Fo)
-0.2
-10
-1
-50
-20
5.00E-11
-
0.2
10
1
50
70
MHz
ppm
ppb
ppb/day
RMS
ppb
°C
Supply Voltage
Voltage Stability (+/-1%)
Power Consumption: Turn On
Power Consumption: Steady-State
Warm Up
2G Tip-over
(Vcc)
4.75
-1.0
-100
-
5.00
5
5.25
1.0
3.50
1.5
100
-
Vdc
ppb
W
W
ppb
ppb/G
10.23
MINIMUM
NOMINAL
MAXIMUM
UNITS
0.0
2.5
5.0
Vdc
±1.0
10K
-
±3.0
-
ppm
Ohm
PARAMETER
LOAD
Output Power
Spurious Output
Harmonics
Jitter (BW=10Hz to Fo/2)
Period Jitter
SSB Phase Noise at 1Hz offset
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
MINIMUM
45
7.0
NOMINAL
50
-
-
-70
-100
-130
-140
MAXIMUM
55
10.0
-100
-30
2
2
-
UNITS
ohms
dBm
dBc
ðBc
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-150
-
dBc/Hz
PARAMETER
Vc
SINEWAVE OUTPUT CHARACTERISTICS
PACKAGE CHARACTERISTICS
Notes:
1)
2)
3)
4)
5)
6)
7)
OVC5EE3BA
10.230 MHz
1
2
DESCRIPTION
3
4
5
6
7
NOTE
Cx110
TABLE 4.0
NOTE
TABLE 5.0
Metal package: solder sealed, grounded case, solder tinned pins.
See solder profile on page 2.
PAGE 1
OF
2
REV: 01
DATE:
The Connor-Winfield
OVC5EE3BA is a 5V Oven
Controlled Voltage Controlled
Crystal Oscillator (OCVCXO)
with a Sinewave output. The
OVC5EE3BA is designed for
applications requiring low
jitter and tight frequency
stability.
FEATURES
Initial calibration @ 25C, Vc=2.5Vdc at time of shipment.
Frequency stability vs. change in temperature stability -20C to 70C absolute.
Allen Variance: 1 second, 100 average.
Frequency vs. change in supply voltage, referenced to 5.00 Vdc.
Vcc = 5.0Vdc.
Measured @ 25C.
Measured @-20C, within 5 minutes, referenced one hour after turn-on.
DATA SHEET #:
OVC5EE3BA
NOTE
TABLE 3.0
INPUT CHARACTERISTICS
Package
Solder Process
0646
TABLE 2.0
PARAMETER
Control Voltage (Pin 3)
Deviation @ 25°C referenced to Fo @
Vc=2.5V
Input Impedance (Pin 3)
I( W
NOTE
05/15/07
VOLTAGE CONTROLLED OCXO
5.0V OPERATION
FREQUENCY STABILITY: 10ppb
ABSOLUTE
TEMPERATURE RANGE: -20 to 70°C
SINEWAVE OUTPUT
HERMETICALLY SEALED PACKAGE
RoHS COMPLIANT / LEAD FREE
ORDERING INFORMATION
OVC5EE3BA
OCXO
SERIES
- 10.230 MHz
CENTER
FREQUENCY
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles, 10
minute dwell, 1minute transition.
Gross Leak Test: Per MIL-STD-202, Method 2003, Method 112, Condition D, No bubbles in
flourinert (FC-43) at 125C +/-5C for 20 seconds.
SOLDERING
Pin Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 254°C ±5°C Solder
pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside boardmount product, 260°C ±5°C for 20 seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204D, Condition A. 10G’s peak, 10Hz to 500Hz, 15 minute
cycles 12 times each perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, half sine, 3 shocks per
direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.
Solder Profile
TOP VIEW
Temperature
260°C
260°C
I( W
0646
220°C
180°C
150°C
OVC5EE3BA
10.230 MHz
120°C
0
120 S
Max.
Time
10 S
60 S
Max.
360 Sec. Max.
Pin Connections
Package Outline
TABLE 6.0
Pin
1
2
3
4
5
Connection
Output
Ground, Case
Control Voltage
N/C
Vcc
Test Circuit
CONTROL
VOLTAGE
0 to 5V
Dimensional Tolerance:
±.005 (.127mm)
Specifications subject to change without notice.
DATA SHEET #:
Cx110
PAGE 2
OF
2
REV:
01
DATE:
05/15/07
aCopyright 2001 Connor-Winfield all rights reserved.