CPI VZU-6995AY

500W Compact High Power Amplifier
for Satellite Communications
DBS-Band
The VZU-6995AY
DBS-Band
500 Watt TWT High
Power Amplifier—
high efficiency in a
compact package.
Easy to Maintain
Provides 500 watts of power in a 5 rack unit
package, digital ready, for wideband, single- and
multi-carrier satellite service in the 17.3-18.4 GHz
frequency band. Ideal for transportable and fixed
earth station applications where space and prime
power are at a premium.
Modular design and built-in fault diagnostic
capability with convenient and clearly visible
indicators for easy maintainability in the field.
Efficient
Employs a high efficiency dual-depressed
collector helix traveling wave tube backed by
many years of field-proven experience in
airborne and military applications.
Worldwide Support
Backed by over three decades of satellite
communications experience, and CPI’s worldwide
24-hour customer support network that includes
fifteen regional factory Service Centers.
Simple to Operate
User-friendly microprocessor-controlled
logic with integrated computer interface.
Digital metering, pin diode attenuation and
optional integrated linearizer for improved
intermodulation performance.
Global Applications
Meets International Safety Standard EN-60215,
Electromagnetic Compatibility 89/336/EEC and
Harmonic Standard EN-61000-3-2 to satisfy
worldwide requirements.
811 Hansen Way
P.O. Box 51625, Palo Alto, CA 94303
tel: +1 (650) 846-3803
fax: +1 (650) 424-1744
e-mail: marketing@satcom.cpii.com
www.cpii.com/satcom
500W Compact High Power Amplif ier
Compact
DBS - B a n d
SPECIFICATIONS, VZU-6995AY
Electrical
OPTIONS:
Electrical (continued)
Frequency
17.3 to 18.4 GHz
Output Power
TWT
Flange
500 W min. (56.99 dBm min.)
407 W min. (56.10 dBm min.)
Bandwidth
1100 MHz
Gain
75 dB min. at rated power, 88 dB max.
78 dB min. at small signal, 90 dB max.
RF Level Adjust Range
0 to 20 dB (via PIN diode attenuator)
• Integral Linearizer
• Remote Control Panel
Gain Stability
At constant drive & temp.
• Redundant and Power
Combined Subsystems
Over temp., constant drive
(any frequency)
Small Signal Gain Slope
Small Signal Gain Variation
Across any 80 MHz band
Across the 1100 MHz band
Across the 1100 MHz band,
with linearizer
±0.25 dB/24hr max.
(after 30 min. warmup)
±1.0 dB over oper. temp. range (typical)
±0.75 dB over ±10°C (typical)
±0.02 dB/MHz max.
1.0 dB pk-pk max.
4.0 dB pk-pk max.
6.0 dB pk-pk max.
Input VSWR
1.30:1 max.
Output VSWR
1.30:1 max.
Load VSWR
Continuous operation
Full spec compliance
Operation without damage
2.0:1
1.2:1
Any value
Residual AM, max.
-50 dBc below 10 kHz
-20 [1.5 +log F(kHz)] dBc,
10 kHz to 500 kHz
-85 dBc above 500 kHz
Phase Noise
IESS-308/309
phase noise profile
-6 dB
AC fundamentals related
-36 dBc
Sum of spurs (370 Hz to 1 MHz) -47 dBc
AM/PM Conversion
2.5°/dB max. for a single-carrier at
8 dB below rated power
Harmonic Output
-60 dBc max. at rated power,
second and third harmonics
Noise and Spurious
<-120 dBW/4 kHz, below 16.5 GHz
<-65 dBW/4 kHz, 17.3 to 18.4 GHz
<-60 dBW/4 kHz, in passband with
linearizer
<-105 dBW/4 kHz, 18.9 to 26.0 GHz
<-125 dBW/4 kHz, 26.0 to 40.0 GHz
Noise Figure
10 dB max.; 15 dB max. with
optional integral linearizer
Intermodulation
-21 dBc or better with two equal carriers
at total output power level 7 dB
(4 dB with optional integral linearizer)
below rated single-carrier output
KEEPING YOU ON THE AIR
not up in the air
Certificate Number: 30515
For more detailed information, please refer to the corresponding CPI Technical Description.
Note: Specifications may change without notice as a result of additional data or product refinement.
Please contact CPI before using this information for system design.
MKT 54, ISSUE 9
08/06
PDF
Group Delay
(in any 80 MHz band)
Primary Power
Voltage
Frequency
Power Consumption
0.01 ns/MHz linear max.
0.001 ns/MHz sq. parabolic max.
0.5 ns pk-pk ripple max.
Single phase, 208-240 VAC ±10%
47-63 Hz
2.3 kVA typ. (small signal)
2.8 kVA max.
Power Factor
0.95 min.
Inrush Current
200% max.
Environmental (Operating)
Ambient Temperature
-10° to +50°C operating
-40° to +70°C non-operating
Relative Humidity
95% non-condensing
Altitude
10,000 ft. with standard adiabatic
derating of 2°C/1000 ft., operating;
50,000 ft., non-operating
Shock and Vibration
Designed for normal transportation
environment per Section 514.4
MIL-STD-810E. Designed to
withstand 20G at 11 ms
(1/2 sine pulse) in non-operating
condition.
Mechanical
Cooling (TWT)
Forced air with integral blower
Rear air intake & exhaust
Maximum external pressure loss
allowable: 0.5 inches water column
RF Input Connection
Type SMA female
RF Output Connection
WR-62 waveguide flange,
grooved, threaded UNC 2B 6-32
RF Output Monitor
Type SMA female
Dimensions (W x H x D)
19 x 8.75 x 24 in.
(483 x 222 x 610 mm)
Weight
95 lbs (43 kg) max.
Heat and Acoustic
Heat Dissipation
2,000 Watts max.
Acoustic Noise
68 dBA (as measured at 3 ft.)