EMERSON-NETWORKPOWER ALH60

60Amps
Total Power:
Input Voltages:
No. of Outputs:
200 Watts (3.3V @ 60A)
48 V
Single
AEH60
ALH60 (Open Frame)
Electrical Specs
Ultra High Efficiency Half Brick
Input
Input range
Input Surge
Efficiency
36-75 VDC
100V / 100ms
91% @ 3.3V (Typical)
Control
Enable
TTL compatible
(positive or negative enable logic
control options)
Output
Special Features
•
•
•
•
•
•
•
•
High efficiency, [email protected] 91% (Typical)
Baseplate (AEH) or Open frame (ALH) design
Low output ripple and noise
High capacitive load limit on start-up
Remote sense compensation
Regulation to zero load
Fixed frequency switching
Industry Std features: Input UVLO, OCP, OVP,
OTP; Short ckt protection; ±10% Output Adjust
• Positive or Negative enable logic control option
• Meets Basic Insulation
Regulation
(Line, Load, Temp)
<2%
Ripple and Noise1
Remote Sense
2% typical (100mVp-p max)
Up to 10%Vout
Output Voltage Adjust
Range
±10% of nominal output
Transient Response
60mV typical output deviation
25% step change
150 µS recovery time
Overv Voltage
Protection
135% nominal output (latching)
Over Current
Protection
115% of full load (latching)
Over Temperature
Protection
Shutdown - autorecovery mode
Isolation Voltage
1500 Vdc
Environmental
Operating temperature
-40°C to +100°C Baseplate (AEH60)
-40°C to +85°C Ambient (ALH60)
Storage temperature: -55°C to +125°C
Overtemperature protection: 115°C PCB
Temperature (Typical)
MTBF: >1 million hours
Safety
UL, cUL 60950 Recognized
TUV
2
EN60950 Licensed
North America (USA): 1-888-41-ASTEC
Europe (UK): 44 (1384) 842-211Asia (HK): 852-2437-9662
AMERICAS
EUROPE
ASIA
5810 Van Allen Way
Carlsbad, CA 92008
Telephone: 760-930-4600
Facsimile: 760-930-0698
Astec House, Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX, UK
Telephone: 44 (1384) 842-211
Facsimile: 44 (1384) 843-355
Units 2111-2116, Level 21
Tower1, Metroplaza
223, Hing Fong Road
Fwai Fong, New Territories
Hong Kong
Telephone: 852-2437-9662
Facsimile: 852-2402-4426
Ordering Information
Input
Voltage
Output
Voltage
48V
48V
48V
48V
48V
3.3V
2.5V
2.5V
1.8V
1.2V
@
@
@
@
@
48V
48V
48V
48V
3.3V
2.5V
1.8V
1.2V
@
@
@
@
OPTION:
Efficiency
Model Number
60A
60A
60A
60A
60A
91% (Typ)
90% (Typ)
90% (Typ)
89% (Typ)
85% (Typ)
AEH60F48(N)
AEH60G48(N)
AEH60G48N-6T
AEH60Y48(N)
AEH60K48(N)
60A
60A
60A
60A
91% (Typ)
90% (Typ)
89% (Typ)
85% (Typ)
ALH60F48(N)
ALH60G48(N)
ALH60Y48(N)
ALH60K48(N)
(see note 3)
suffix “N” = Negative Enable (default is Positive Enable without suffix “N”)
Standard pin length is 5mm nominal. Consult factory for other options.
AEH - BASEPLATE
Pin Assignments
0.20
[5.1]
+Vin
Enable (On/Off)
Case (AEH version)
-Vin
- Output
- Sense
Trim
+ Sense
+ Output
Notes:
0.50
[12.7]
0.20
[5.2]
M3 X0.5 MOUNTING HOLE
4 PLACES
0.08Ø[2.0Ø] 2 PLACES
0.20
[5.1]
Single Output
1.
2.
3.
4.
5.
6.
7.
8.
9.
2.30
[58.4]
1.90
[48.3]
+ Output
+ Vin
0.04Ø [1.0Ø] 7 PLACES
2.00
[50.8]
- Vin
2.40
[61.0]
-Output
0.46
[11.8]
PIN SIDE DOWN
1.90
[48.3]
0.50
[12.7]
SIDE VIEW
0.50
[12.7]
PIN ASSIGNMENT
0.90
1.20 [22.8]
1.50 [30.4]
1.90 [38.1]
[48.3]
0.90
[22.9]
4
5
6
3
1.20
[30.5] 1.50
[38.2]
1 + Vin
2 Enable (On/Off)
3 CASE
4 - Vin
5 -Output
6 -Sense
7 Trim
8 + Sense
9 + Output
1.90
[48.3]
7
2
1. 20 mHz bandwidth. External 10 uF tant. capacitor +
0.1 uF cer. capacitor placed from +V out to -Vout.
2. Requires a 2.2 mf, 100V film capacitor connected
between +V in and -V in to meet FCC class A and
ETS300-386-1 requirements for conducted noise.
Consult Factory for filtering information to meet FCC
class B, VDE or EIC specifications.
3. Suffix -”6” for 3.7mm nominal pin length, “T” for tuned
version for specific transient response requirement.
Minimum output capacitance required. Refer to
Technical refernce Notes for details.
4. All specifications are typical at nominal line, full load,
and 25°C unless otherwise noted.
5. All specifications subject to change without notice.
Mechanical drawings are for reference only
6. Technical Reference Notes should be consulted for
detailed information when available
7. Warranty: 1yr
* Astec reserves the right to make changes to the information
contained herein without notice and assumes no liability as a
result of its use or application. (REV05: FEBRUARY 2, 2004)
9
1
NOTES:
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)
PIN PLACEMENT TOLERANCE : ± 0.005(0.127)
MECHANICAL TOLERANCE ± .002(0.5)
PIN SIDE UP
2.30
[58.4]
1.90
[48.3]
0.20
[5.1]
0.20
[5.1]
0.40
[10.2]
+ Vin 1
9
2
+ Output
0.04Ø[1.0Ø] 7 PLACES
8
2.40 2.00
[60.9] [50.8]
7
3
6
5
- Vin
0.08Ø[2.0Ø] 2 PLACES
-Output
4
SIDE VIEW
PIN SIDE DOWN
PIN ASSIGNMENT
1.90
[48.3]
0.90
1.20 [22.9]
[30.5]
1.50
1.90 [38.1]
[48.3]
0.21
[5.4]
0.50
[12.7]
4
5
3
6
7
2
8
1
9
PIN SIDE UP
0.50
[12.7] 0.90
[22.9]
1.20
[30.5] 1.50
[38.1] 1.90
[48.2]
1 + Vin
2 Enable (On/Off)
3 CASE
4 - Vin
5 -Output
6 -Sense
7 Trim
8 + Sense
9 + Output
NOTES:
ALL DIMENSIONS ARE IN INCHES (MILLIMETERS)
PIN PLACEMENT TOLERANCE : ± 0.005(0.127)
MECHANICAL TOLERANCE ± .002(0.5)
ALH - BASEPLATE
www.astecpower.com
3