EMERSON-NETWORKPOWER SMT06C

Embedded Power for
Business-Critical Continuity
Rev. 08.20.08_j93
SMT06C
1 of 4
SMT06C Series
5 Vin and 12 Vin
single output
Total Power:
20W
Input Voltage: 4.5-5.5 Vdc or
10.2 - 13.8 Vdc
# of Outputs: Single
Electrical Specifications
Special Features
• 6 A current rating
• Input voltage range:
4.5 Vdc - 5.5 Vdc or
10.2 Vdc - 13.8 Vdc
• Output voltage range:
0.9 Vdc - 3.3/5.0 Vdc
• Industry leading value
• Cost optimized design
• Excellent transient response
• Output voltage adjustability
• Pathway for future
upgrades
• Supports silicon voltage
migration
• Resulting in reduced
design-in and qualification
time
• Designed in reliability:
MTBF of >7 million hours
per Telcordia SR-332
• Available RoHS compliant
• 2 year warranty
Safety
UL/cUL : CAN/CSA 22.2
No. 60950
TÜV Product Service
(EN60950:2000)
CB report and certificate
Output
Voltage adjustability (see note 6) 5 V input models
12 Vins
Output setpoint accuracy
1.0% trim resistors
0.9 - 3.3 Vdc
0.9 - 5.0 Vdc
±2.5%
Line regulation
Low line to high line
±0.2%
Load regulation
Full load to min. load
Min/max load
±0.5%
0A/6A
Overshoot (at turn on)
5 V input models
12 V input models
3.0% max.
1.0% max.
Undershoot
At turn-off
100 mV max.
Ripple and noise 5 Hz to 20 MHz
(See note 2)
See table on page 2
Transient response (see note 1)
75 mV max. deviation
150 μs recovery to
within regulation band
Embedded Power for
Business-Critical Continuity
All specifications are typical at nominal input, full load at 25°C unless otherwise stated.
Input
Input voltage range
5 V input model
12 V input model
4.5 - 5.5 Vdc
10.2 - 13.8 Vdc
Input current
Minimum load
Remote OFF
50 mA
5 mA
Input current (max.)
(see note 8)
5 V input model
12 V input model
5.1 A max. @ lo max.
1.6 A @ lo max.
Input reflected ripple
(see note 2)
5 Vin
12 Vin
52 mA (pk-pk)
56 mA (pk-pk)
Remote ON/OFF
Logic compatibility
ON
OFF
Positive logic
>2.4 Vdc
<0.8 Vdc
Start-up time (see note 3) Power up
Remote ON/OFF
<20 ms
<20 ms
Turn ON threshold
5 Vin
12 Vin
4.5 Vdc typ.
9.3 Vdc typ.
Turn OFF threshold
5 Vin
12 Vin
4.3 Vdc typ.
7.8 Vdc typ.
General Specifications
Efficiency
See table on page 2
Switching frequency
Fixed
200 kHz.
Approvals and standards
(See note 4)
TÜV product Services
IEC69050, UL/cUL60950
Material flammability
UL94V-0
Weight
9.3 g (0.3 oz.)
Coplanarity
150 µm
MTBF
Telcordia SR-332
7,562,142 hours
Environmental Specifications
Thermal performance
(see note 9)
Operating ambient,
temperature
Non-operating
0 °C to +80 °C
-40 °C to +125 °C
Protection
Short-circuit
Hiccup, non-latching
Recommended system capacitance
Input capacitance
(See note 10)
270 μF/20 mW ESR max.
Output capacitance
(See note 10)
680 μF/10 m W ESR max.
Rev. 08.20.08_j93
SMT06C
2 of 4
Embedded Power for
Business-Critical Continuity
Rev. 08.20.08_j93
SMT06C
3 of 4
Ordering Information
Output
Power
(max)
Input
Voltage
Output
Voltage (11)
Output
Current
(min)
Output
Current
(max)
Maximum
Load (typ)
Regulation
Model Numbers (12, 13)
Line
Load
20 W
4.5-5.5 Vdc
0.9-3.3 V
0A
6A
89%
±0.2%
±0.5%
SMT06C-05SADJJ
30 W
10.2 - 13.8 Vdc
0.9-5.0 V
0A
6A
91%
±0.2%
±0.5%
SMT06C-12SADJJ
All specifications are typical at nominal input Vin = 12 V, full load at 25°C unless otherwise stated.
Part Number System with Options
Product Family
Rated Output
Current
Performance
Input Voltage
Number of Outputs
Packaging Options
SMT
06
C
12
SADJ
J
SMT = Surface Mount
06 = 6 A
C = C Series
05 = 4.5 Vdc to 5.5 Vdc
12 = 10.2 Vdc to 13.8 Vdc
SADJ = Single Adjustable
Output
J = PB-free (RoHS 6/6 compliant)
Output Voltage Adjustment of the SMT20C Series
The ultra-wide output voltage trim range offers major advantages to users who
select the SMT06C series. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SMT06C series converter
leaves the factory the output has been adjusted to the default voltage of 0.9 V.
Notes
di/dt = 10 A/μs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo max. to 0.75 lo
max. and 0.75 lo max. to 0.5 lo max.
2 Measured with external filter. See Application Note 169 for details.
3 Power up is the time from application of dc input to Power Good high.
Remote ON/OFF asserted high to Power Good high.
4 This product is only for inclusion by professional installers within other
equipment and must not be operated as a stand alone product.
5 Measured as per recommended set-up. Cin = 270 μF (20 mW ESR max.).
Cout = 680 μF (10 mW ESR max.).
6 Uses external resistor from trim to ground. Minimum value 485 W for 5 V
model, 280 W for 12 V model. See Application Note 169 for details.
7 Signal line assumed <3 m.
8 External input fusing recommended.
9 See Application Note 169 for operation above 50 ºC.
10 See Application Note 169 for more details.
11 TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special
request, please contact your local sales representative for details.
12 NOTICE: Some models do not support all options. Please contact your local
representative or use the on-line model number search tool at
www.powerconversion.com to find a suitable alternative.
Ripple and Noise Specification
1
Output
Voltage
Pk - Pk
RMS
5 V input models
0.9 Vdc to 2.5 Vdc
3.3 Vdc
30 mV
40 mV
15 mV
15 mV
12 V input models
0.9 Vdc to 2.5 Vdc
3.3 Vdc to 5 Vdc
40 mV
50 mV
20 mV
20 mV
Model
Embedded Power for
Business-Critical Continuity
Americas
Mechanical Drawing
0.190
(4.83)
1.200
(30.48)
0.190
(4.83)
0.190
(4.83)
0.190
(4.83)
Europe (UK)
0.310
(7.87)
0.430
(10.93)
0.530
(13.46)
0.050
(1.27)
PIN 6
Seating Plane
0.062
(1.57) REF
6 x 0.089
(2.26)
0.019
(0.48) TYP
All dimensions in inches (mm)
All tolerance 0.010in (0.25mm)
unless otherwise stated
Pin connections
Pin Number
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
Telephone: +44 (0) 1384 842 211
Facsimile: +44 (0) 1384 843 355
Asia (HK)
PIN 1
0.315
(8.00)
0.75
(1.90)
0.466 (11.83)
Installed Ht.
5810 Van Allen Way
Carlsbad, CA 92008
USA
Telephone: +1 (760) 930 4600
Facsimile: +1 (760) 930 0698
PIN 5
PIN 2
Rev. 08.20.08_j93
SMT06C
4 of 4
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
Telephone: +852 2176 3333
Facsimile: +852 2176 3888
For global contact, visit:
www.powerconversion.com
[email protected]
powerconversion.com
While every precaution has been taken to ensure
accuracy and completeness in this literature, Emerson
Network Power assumes no responsibility, and disclaims
all liability for damages resulting from use of this
information or for any errors or omissions.
Function
1
2
3
4
5
Remote ON/OFF
Power Good
Trim
Vout
GND
6
Vin
Emerson Network Power.
The global leader in enabling
business-critical continuity.
AC Power
Connectivity
DC Power
Embedded Computing
Embedded Power
Monitoring
Outside Plant
Power Switching & Controls
Precision Cooling
Racks & Integrated Cabinets
Services
Surge Protection
EmersonNetworkPower. com
Emerson Network Power and the Emerson
Network Power logo are trademarks and
service marks of Emerson Electric Co.
©2008 Emerson Electric Co.