PRODUCT DATA SHEET P7500 Family COMMON MODE CHOKE Features Applications ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Small size Wideband suppression Low profile (<2.0mm) Surface Mount Flat top for pick & place Lead-free (Pb-free) Noise suppression Common mode suppression USB lines IEEE 1394 DESCRIPTION The P7500 family is suitable for Common Mode suppression across a broad range of signal applications. Good Common Mode performance is achieved to beyond 500MHz. All chokes will handle DC currents of 300mA minimum. P7500-2012 ETALDOC 845/2 Components are available in two mechanical sizes similar to EIA 0805 and 1206. The P7500 family of components provides reliable lead-free terminations suitable for lead-free and conventional placement and reflow. P7500-3216 Page 1 of 4 July 2005 P7500 SPECIFICATIONS Electrical 2012 size (EIA 0805) Part Number Common mode Impedance (1) at 100MHz (Ω) DCR (Ω) Max 90±25% 160±25% 220±25% 0.30 0.35 0.40 Common mode Impedance (1) at 100MHz (Ω) DCR (Ω) Max 90±25% 160±25% 220±25% 0.30 0.35 0.40 P7500-2012-900MT P7500-2012-161MT P7500-2012-221MT Rated Current IDC (mA) (2) 400 350 300 3216 size (EIA 1206) Part Number P7500-3216-900MT P7500-3216-161MT P7500-3216-221MT Rated Current IDC (mA) (2) 400 350 300 Notes 1. 2. 3. 4. See fig. 1 and fig. 2 for typical impedance vs. frequency characteristics. Rated current, IDC, is the current at which the temperature rise is 40ºC (max). Operating temperature -40ºC to +85ºC. For non-standard inductance values, please contact Profec. Voltage ratings (all variants) Rated voltage 50VDC Withstand Voltage 125VDC Insulation resistance 10MΩ (min) ETALDOC 845/2 Page 2 of 4 July 2005 P7500 P7500-2012 impedance vs frequency characteristics 1000.0 Fig. 1 COMMON MODE IMPEDANCE IMPEDANCE (Ohm) 100.0 900 10.0 161 221 1.0 900 161 NORMAL MODE IMPEDANCE 221 0.1 1 10 100 FREQUENCY (MHz) 1000 10000 P7500-3216 impedance vs frequency characteristics 1000.0 Fig. 2 COMMON MODE IMPEDANCE IMPEDANCE (Ohm) 100.0 900 10.0 161 221 1.0 900 161 NORMAL MODE IMPEDANCE 221 0.1 ETALDOC 845/2 1 10 100 FREQUENCY (MHz) Page 3 of 4 1000 10000 July 2005 P7500 CONSTRUCTION P7500-2012 dimensions P7500-3216 dimensions Fig. 3 Fig. 4 3.2± 0.2 0.6 typ e3 0.4 typ e3 2.0± 0.2 1.2 ± 0.2 1.6± 0.2 1.2 ± 0.2 2.0± 0.2 0.6 typ 1.1 1.05 1.6 0.4 0.75 0.6 0.45 0.4 0.45 typ PCB PATTERN PCB PATTERN Dimensions shown are in millimetres Terminal plating JESD97 Category = e3. Recommended reflow solder profile: 2 minutes @ 150-200ºC, 10 seconds @ 260ºC; time above 217ºC 60 seconds maximum. Note: these parts are ceramic bodied: avoid PCB flexure after mounting. ORDERING CODE P7500- - ABSOLUTE MAXIMUM RATINGS Storage temperature -40ºC to +105ºC Tape and Reel Operating temperature -40ºC to +85ºC Tolerance (±25%) Soldering temperature peak Reflow Hand 260ºC 10s 260ºC 3s MT Impedance code (900, 161 or 221) Size (2012 or 3216) Type code Handle in accordance with IPC/JEDEC J-STD-033 procedure for components classified as IPC/JEDEC J-STD-020 Moisture Sensitivity Level 2. ISO 9001 FM 25326 ETAL Group Oy, Kuormatie 14, FIN-03101, Nummela Telephone: +358 (0)20 7500 330 Fax: +358 (0)20 7500 333 Website: www.etalgroup.com Email: [email protected] ETALDOC 845/2 Page 4 of 4 July 2005