XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION 2009 REV. 1.0.1 GENERAL DESCRIPTION The XRT86VX38 is an eight-channel 1.544 Mbit/s or 2.048 Mbit/s DS1/E1/J1 framer and Long-haul/Shorthual LIU integrated solution featuring R3 technology (Relayless, Reconfigurable, Redundancy) and BITS Timing element. The physical interface is optimized with internal impedance, and with the patented pad structure, the XRT86VX38 provides protection from power failures and hot swapping. The XRT86VX38 contains an integrated DS1/E1/J1 framer and LIU which provide DS1/E1/J1 framing and error accumulation in accordance with ANSI/ITU_T specifications. Each framer has its own framing synchronizer and transmit-receive slip buffers. The slip buffers can be independently enabled or disabled as required and can be configured to frame to the common DS1/E1/J1 signal formats. Each Framer block contains its own Transmit and Receive T1/E1/J1 Framing function. There are 3 Transmit HDLC controllers per channel which encapsulate contents of the Transmit HDLC buffers into LAPD Message frames. There are 3 Receive HDLC controllers per channel which extract the payload content of Receive LAPD Message frames from the incoming T1/E1/J1 data stream and write the contents into the Receive HDLC buffers. Each framer also contains a Transmit and Overhead Data Input port, which permits Data Link Terminal Equipment direct access to the outbound T1/E1/J1 frames. Likewise, a Receive Overhead output data port permits Data Link Terminal Equipment direct access to the Data Link bits of the inbound T1/E1/J1 frames. The XRT86VX38 fully meets all of the latest T1/E1/J1 specifications: ANSI T1/E1.107-1988, ANSI T1/ E1.403-1995, ANSI T1/E1.231-1993, ANSI T1/ E1.408-1990, AT&T TR 62411 (12-90) TR54016, and ITU G-703, G.704, G706 and G.733, AT&T Pub. 43801, and ETS 300 011, 300 233, JT G.703, JT G.704, JT G706, I.431. Extensive test and diagnostic functions include Loop-backs, Boundary scan, Pseudo Random bit sequence (PRBS) test pattern generation, Performance Monitor, Bit Error Rate (BER) meter, forced error insertion, and LAPD unchannelized data payload processing according to ITU-T standard Q.921. . APPLICATIONS AND FEATURES (NEXT PAGE) FIGURE 1. XRT86VX38 EIGHT CHANNEL DS1 (T1/E1/J1) FRAMER/LIU COMBO Local PCM Highway External Data Link Controller XRT86VX38 Tx Overhead In Rx Overhead Out 1:2 Turns Ratio Tx Serial Data In TTIP 2-Frame Slip Buffer Elastic Store Tx LIU Interface Tx Framer Tx Serial Clock ST-BUS LLB Rx Serial Clock TRING LB RTIP Rx Serial Data Out 2-Frame Slip Buffer Elastic Store Rx Framer Rx LIU Interface PRBS Generator & Analyser Performance Monitor HDLC/LAPD Controllers LIU & Loopback Control RRING RxLOS Line Side 8kHz sync OSC Back Plane 1.544-16.384 Mbit/s 1:1 Turns Ratio Signaling & Alarms Microprocessor Interface DMA Interface JTAG 3 System (Terminal) Side INT TxON Memory D[7:0] A[11:0] P Select 4 WR ALE_AS RD RDY_DTACK Intel/Motorola µP Configuration, Control & Status Monitor Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 APPLICATIONS High-Density T1/E1/J1 interfaces for Multiplexers, Switches, LAN Routers and Digital Modems SONET/SDH terminal or Add/Drop multiplexers (ADMs) T1/E1/J1 add/drop multiplexers (MUX) Channel Service Units (CSUs): T1/E1/J1 and Fractional T1/E1/J1 BITS Timing Digital Access Cross-connect System (DACs) Digital Cross-connect Systems (DCS) Frame Relay Switches and Access Devices (FRADS) ISDN Primary Rate Interfaces (PRA) PBXs and PCM channel bank T3 channelized access concentrators and M13 MUX Wireless base stations ATM equipment with integrated DS1 interfaces Multichannel DS1 Test Equipment T1/E1/J1 Performance Monitoring Voice over packet gateways Routers FEATURES Supports Section 13 - Synchronization Interface in ITU G.703 for both Transmit and Receive Paths Supports SSM Synchronous Messaging Generation (BOC for T1, National Bits for E1) on the Transmit Path Supports SSM Synchronous Messaging Extraction (BOC for T1, National Bits for E1) on the Receive Path Supports BITS timing generation on the Transmit Outputs Supports BITS timing extraction from NRZ data on the Analog Receive Path DS-0 Monitoring on both Transmit and Receive Time Slots Supports SSM Synchronization Messaging per ANSI T1.101-1999 and ITU G.704 Supports a Customized Section 13 - Synchronization Interface in G.703 at 1.544MHz Independent, full duplex DS1 Tx and Rx Framer/LIUs Each channel has full featured Long-haul/Short-haul LIU Two 512-bit (two-frame) elastic store, PCM frame slip buffers (FIFO) on TX and Rx provide up to 8.192 MHz asynchronous back plane connections with jitter and wander attenuation Supports input PCM and signaling data at 1.544, 2.048, 4.096 and 8.192 Mbits. Also supports 2-channel multiplexed 12.352/16.384 (HMVIP/H.100) Mbit/s on the back plane bus Programmable output clocks for Fractional T1/E1/J1 Supports Channel Associated Signaling (CAS) Supports Common Channel Signalling (CCS) Supports ISDN Primary Rate Interface (ISDN PRI) signaling 2 XRT86VX38 REV. 1.0.1 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION 8-CHANNEL T1/E1/J1 FRAMER/ Extracts and inserts robbed bit signaling (RBS) 3 Integrated HDLC controllers for transmit and receive, each controller having two 96-byte buffers (buffer 0 / buffer 1) HDLC Controllers Support SS7 Timeslot assignable HDLC V5.1 or V5.2 Interface Automatic Performance Report Generation (PMON Status) can be inserted into the transmit LAPD interface every 1 second or for a single transmission Supports SPRM and NPRM Alarm Indication Signal with Customer Installation signature (AIS-CI) Remote Alarm Indication with Customer Installation (RAI-CI) Gapped Clock interface mode for Transmit and Receive. Intel/Motorola and Power PC interfaces for configuration, control and status monitoring Parallel search algorithm for fast frame synchronization Wide choice of T1 framing structures: SF/D4, ESF, SLC®96, T1DM and N-Frame (non-signaling) Direct access to D and E channels for fast transmission of data link information Full BERT Controller for generation and detection on system and line side of the chip PRBS, QRSS, and Network Loop Code generation and detection Seven Independent, simultaneous Loop Code Detectors per Channel Programmable Interrupt output pin Supports programmed I/O and DMA modes of Read-Write access The framer block encodes and decodes the T1/E1/J1 Frame serial data Detects and forces Red (SAI), Yellow (RAI) and Blue (AIS) Alarms Detects OOF, LOF, LOS errors and COFA conditions Loopbacks: Local (LLB) and Line remote (LB) Facilitates Inverse Multiplexing for ATM Performance monitor with one second polling Boundary scan (IEEE 1149.1) JTAG test port Accepts external 8kHz Sync reference 1.8V Inner Core 3.3V CMOS operation with 5V tolerant inputs 256-pin fpBGA and 329-pin fpBGA package with -40C to +85C operation ORDERING INFORMATION PART NUMBER PACKAGE OPERATING TEMPERATURE RANGE XRT86VX38IB256 256 PIn Fine Pitch Ball Grid Array -40C to +85C XRT86VX38IB329 329 PIn Fine Pitch Ball Grid Array -40C to +85C 3 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 LIST OF TABLES Table 1:: Register Summary .............................................................................................................................................. 4 Table 2:: Clock Select Register(CSR) Hex Address: 0xN100 .......... 9 Table 3:: Line Interface Control Register (LICR) Hex Address: 0xN101 ............... 11 Table 4:: Framing Select Register (FSR) Hex Address: 0xN107 .................... 13 Table 5:: Alarm Generation Register (AGR) Hex Address: 0xN108 ..................... 15 Table 6:: yellow alarm duration and format when one second rule is not enforced ......................................................... 16 Table 7:: yellow alarm format when one second rule is enforced .................................................................................... 17 Table 8:: Synchronization MUX Register (SMR) Hex Address: 0xN109 ................... 19 Table 9:: Transmit Signaling and Data Link Select Register (TSDLSR) Hex Address:0xN10A .................... 22 Table 10:: Framing Control Register (FCR) Hex Address: 0xN10B .................. 24 Table 11:: Receive Signaling & Data Link Select Register (RSDLSR) Hex Address: 0xN10C .................... 25 Table 12:: Receive Signaling Change Register 0 (RSCR 0) Hex Address: 0xN10D .......... 27 Table 13:: Receive Signaling Change Register 1(RSCR 1) Hex Address: 0xN10E ...... 27 Table 14:: Receive Signaling Change Register 2 (RSCR 2) Hex Address: 0xN10F ........ 27 Table 15:: Receive In Frame Register (RIFR) Hex Address: 0xN112 .................. 28 Table 16:: Data Link Control Register (DLCR1) Hex Address: 0xN113 .................... 28 Table 17:: Transmit Data Link Byte Count Register (TDLBCR1) Hex Address: 0xN114 .................... 31 Table 18:: Receive Data Link Byte Count Register (RDLBCR1) Hex Address: 0xN115 .................. 32 Table 19:: Slip Buffer Control Register (SBCR) Hex Address: 0xN116 ..................... 33 Table 20:: FIFO Latency Register (FFOLR) Hex Address: 0xN117 ................ 34 Table 21:: DMA 0 (Write) Configuration Register (D0WCR) Hex Address: 0xN118 .................. 35 Table 22:: DMA 1 (Read) Configuration Register (D1RCR) Hex Address: 0xN119 ................. 36 Table 23:: Interrupt Control Register (ICR) Hex Address: 0xN11A ...................... 37 Table 24:: LAPD Select Register (LAPDSR) Hex Address: 0xN11B ................ 37 Table 25:: Customer Installation Alarm Generation Register (CIAGR) Hex Address: 0xN11C ....................... 38 Table 26:: Performance Report Control Register (PRCR) Hex Address: 0xN11D .................... 39 Table 27:: Gapped Clock Control Register (GCCR) Hex Address: 0xN11E .................. 40 Table 28:: Transmit Interface Control Register (TICR) Hex Address:0xN120 .................... 41 Table 29:: Transmit Interface Speed When Multiplexed Mode is Disabled (TxMUXEN = 0) ........................................... 43 Table 30:: Transmit Interface Speed when Multiplexed Mode is Enabled (TxMUXEN = 1) ............................................ 44 Table 31:: PRBS Control & Status Register (PRBSCSR0) Hex Address: 0xN121 ............... 45 Table 32:: Receive Interface Control Register (RICR) Hex Address: 0xN122 .............. 47 Table 33:: Receive Interface Speed When Multiplexed Mode is Disabled (TxMUXEN = 0) ............................................ 49 Table 34:: Receive Interface Speed when Multiplexed Mode is Enabled (TxMUXEN = 1) ............................................. 50 Table 35:: PRBS Control & Status Register (PRBSCSR1) Hex Address: 0xN123 ..................... 51 Table 36:: Loopback Code Control Register (LCCR) Hex Address: 0xN124 ................ 53 Table 37:: Transmit Loopback Coder Register (TLCR) Hex Address: 0xN125 ............. 55 Table 38:: Receive Loopback Activation Code Register (RLACR) Hex Address: 0xN126 ................ 55 Table 39:: Receive Loopback Deactivation Code Register (RLDCR) Hex Address: 0xN127 ................... 55 Table 40:: Defect Detection Enable Register (DDER) Hex Address: 0xN129 .............. 56 Table 41:: Transmit SPRM Control Register (TSPRMCR) Hex Address: 0xN142 ................ 56 Table 42:: Data Link Control Register (DLCR2) Hex Address: 0xN143 ................... 57 Table 43:: Transmit Data Link Byte Count Register (TDLBCR2) Hex Address: 0xN144 ................... 59 Table 44:: Receive Data Link Byte Count Register (RDLBCR2) Hex Address: 0xN145 ................. 60 Table 45:: Data Link Control Register (DLCR3) Hex Address: 0xN153 .................. 61 Table 46:: Transmit Data Link Byte Count Register (TDLBCR3) Hex Address: 0xN154 ................... 63 Table 47:: Receive Data Link Byte Count Register (RDLBCR3) Hex Address: 0xN155 ................. 64 Table 48:: Device ID Register (DEVID) Hex Address: 0xN1FE ........... 65 Table 49:: Revision ID Register (REVID) Hex Address: 0xN1FF .......... 65 Table 50:: Transmit Channel Control Register 0-23 (TCCR 0-23) Hex Address: 0xN300 to 0xN317 ................... 66 Table 51:: Transmit User Code Register 0-23 (TUCR 0-23) Hex Address: 0xN320 to 0xN337 ............... 68 Table 52:: Transmit Signaling Control Register 0-23 (TSCR 0-23) Hex Address: 0xN340 to 0xN357 ...................... 69 Table 53:: Receive Channel Control Register 0-23 (RCCR 0-23) Hex Address: 0xN360 to 0xN377 .................. 71 Table 54:: Receive User Code Register 0-23 (RUCR 0-23) Hex Address: 0xN380 to 0xN397 ............. 73 Table 55:: Receive Signaling Control Register 0-23 (RSCR 0-23) Hex Address: 0xN3A0 to 0xN3B7 ................... 74 Table 56:: Receive Substitution Signaling Register 0-23 (RSSR 0-23) Hex Address: 0xN3C0 to 0xN3D7 .................. 76 Table 57:: Receive Signaling Array Register 0 to 23 (RSAR 0-23) Hex Address: 0xN500 to 0xN517 .................. 77 Table 58:: LAPD Buffer 0 Control Register (LAPDBCR0) Hex Address: 0xN600 .................................... 78 I XRT86VX38 REV. 1.0.1 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION Table 59:: LAPD Buffer 1 Control Register (LAPDBCR1) Hex Address: 0xN700 ..................................... 78 Table 60:: PMON Receive Line Code Violation Counter MSB (RLCVCU) Hex Address: 0xN900 ................ 79 Table 61:: PMON Receive Line Code Violation Counter LSB (RLCVCL) Hex Address: 0xN901 ................ 79 Table 62:: PMON Receive Framing Alignment Bit Error Counter MSB (RFAECU) Hex Address: 0xN902 ................... 80 Table 63:: PMON Receive Framing Alignment Bit Error Counter LSB (RFAECL) Hex Address: 0xN903 ................... 80 Table 64:: PMON Receive Severely Errored Frame Counter (RSEFC) Hex Address: 0xN904 .................. 81 Table 65:: PMON Receive CRC-6 BIT Error Counter - MSB (RSBBECU) Hex Address: 0xN905 ................. 82 Table 66:: PMON Receive CRC-6 Bit Error Counter - LSB (RSBBECL) Hex Address: 0xN906 ................ 82 Table 67:: PMON Receive Slip Counter (RSC) Hex Address: 0xN909 .............. 83 Table 68:: PMON Receive Loss of Frame Counter (RLFC) Hex Address: 0xN90A ............... 83 Table 69:: PMON Receive Change of Frame Alignment Counter (RCFAC) Hex Address: 0xN90B ............... 83 Table 70:: PMON LAPD1 Frame Check Sequence Error Counter 1 (LFCSEC1) Hex Address: 0xN90C ................. 84 Table 71:: PRBS Bit Error Counter MSB (PBECU) Hex Address: 0xN90D ................. 84 Table 72:: PRBS Bit Error Counter LSB (PBECL) Hex Address: 0xN90E ................. 84 Table 73:: Transmit Slip Counter (TSC) Hex Address: 0xN90F .............. 85 Table 74:: Excessive Zero Violation Counter MSB (EZVCU) Hex Address: 0xN910 ................ 85 Table 75:: Excessive Zero Violation Counter LSB (EZVCL) Hex Address: 0xN911 ................. 85 Table 76:: PMON LAPD2 Frame Check Sequence Error Counter 2 (LFCSEC2) Hex Address: 0xN91C ................. 86 Table 77:: PMON LAPD2 Frame Check Sequence Error Counter 3 (LFCSEC3) Hex Address: 0xN92C ................. 86 Table 78:: Block Interrupt Status Register (BISR) Hex Address: 0xNB00 .................... 87 Table 79:: Block Interrupt Enable Register (BIER) Hex Address: 0xNB01 ................... 89 Table 80:: Alarm & Error Interrupt Status Register (AEISR) Hex Address: 0xNB02 .................... 91 Table 81:: Alarm & Error Interrupt Enable Register (AEIER) Hex Address: 0xNB03 ..................... 93 Table 82:: Framer Interrupt Status Register (FISR) Hex Address: 0xNB04 .................. 94 Table 83:: Framer Interrupt Enable Register (FIER) Hex Address: 0xNB05 .................. 96 Table 84:: Data Link Status Register 1 (DLSR1) Hex Address: 0xNB06 ................ 98 Table 85:: Data Link Interrupt Enable Register 1 (DLIER1) Hex Address: 0xNB07 ................ 100 Table 86:: Slip Buffer Interrupt Status Register (SBISR) Hex Address: 0xNB08 ................... 102 Table 87:: Slip Buffer Interrupt Enable Register (SBIER) Hex Address: 0xNB09 .................. 105 Table 88:: Receive Loopback Code Interrupt and Status Register (RLCISR) Hex Address: 0xNB0A .................. 107 Table 89:: Receive Loopback Code Interrupt Enable Register (RLCIER) Hex Address: 0xNB0B .................. 108 Table 90:: Excessive Zero Status Register (EXZSR) Hex Address: 0xNB0E ............... 109 Table 91:: Excessive Zero Enable Register (EXZER) Hex Address: 0xNB0F .............. 109 Table 92:: SS7 Status Register for LAPD1 (SS7SR1) Hex Address: 0xNB10 ............... 110 Table 93:: SS7 Enable Register for LAPD1 (SS7ER1) Hex Address: 0xNB11 ............. 110 Table 94:: RxLOS/CRC Interrupt Status Register (RLCISR) Hex Address: 0xNB12 .............. 111 Table 95:: RxLOS/CRC Interrupt Enable Register (RLCIER) Hex Address: 0xNB13 .............. 111 Table 96:: Data Link Status Register 2 (DLSR2) Hex Address: 0xNB16 ............... 112 Table 97:: Data Link Interrupt Enable Register 2 (DLIER2) Hex Address: 0xNB17 ................ 114 Table 98:: SS7 Status Register for LAPD2 (SS7SR2) Hex Address: 0xNB18 ............... 116 Table 99:: SS7 Enable Register for LAPD2 (SS7ER2) Hex Address: 0xNB19 ............... 116 Table 100:: Data Link Status Register 3 (DLSR3) Hex Address: 0xNB26 ............. 117 Table 101:: Data Link Interrupt Enable Register 3 (DLIER3) Hex Address: 0xNB27 ............. 119 Table 102:: SS7 Status Register for LAPD3 (SS7SR3) Hex Address: 0xNB28 ............ 121 Table 103:: SS7 Enable Register for LAPD3 (SS7ER3) Hex Address: 0xNB29 ........... 121 Table 104:: Customer Installation Alarm Status Register (CIASR) Hex Address: 0xNB40 ................. 122 Table 105:: Customer Installation Alarm Status Register (CIAIER) Hex Address: 0xNB41 ................. 123 Table 106:: LIU Channel Control Register 0 (LIUCCR0) Hex Address: 0xNF00 ............ 124 Table 107:: Equalizer Control and Transmit Line Build Out ........................................................................................... 126 Table 108:: LIU Channel Control Register 1 (LIUCCR1) Hex Address: 0xNF01 ........... 127 Table 109:: LIU Channel Control Register 2 (LIUCCR2) Hex Address: 0xNF02 ............ 129 Table 110:: LIU Channel Control Register 3 (LIUCCR3) Hex Address: 0xNF03 ........... 131 Table 111:: LIU Channel Control Interrupt Enable Register (LIUCCIER) Hex Address: 0xNF04 ................. 133 Table 112:: LIU Channel Control Status Register (LIUCCSR) Hex Address: 0xNF05 ............... 135 Table 113:: LIU Channel Control Interrupt Status Register (LIUCCISR) Hex Address: 0xNF06 .................... 138 Table 114:: LIU Channel Control Cable Loss Register (LIUCCCCR) Hex Address: 0xNF07 ............... 139 Table 115:: LIU Channel Control Arbitrary Register 1 (LIUCCAR1) Hex Address: 0xNF08 .................. 140 Table 116:: LIU Channel Control Arbitrary Register 2 (LIUCCAR2) Hex Address: 0xNF09 ..................... 140 Table 117:: LIU Channel Control Arbitrary Register 3 (LIUCCAR3) Hex Address: 0xNF0A .................... 140 Table 120:: LIU Channel Control Arbitrary Register 6 (LIUCCAR6) Hex Address: 0xNF0D .................... 141 II XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION Table 118:: LIU Channel Control Arbitrary Register 4 (LIUCCAR4) Table 119:: LIU Channel Control Arbitrary Register 5 (LIUCCAR5) Table 121:: LIU Channel Control Arbitrary Register 7 (LIUCCAR7) Table 122:: LIU Channel Control Arbitrary Register 8 (LIUCCAR8) Table 123:: LIU Global Control Register 0 (LIUGCR0) Table 124:: LIU Global Control Register 1 (LIUGCR1) Table 125:: LIU Global Control Register 2 (LIUGCR2) Table 126:: LIU Global Control Register 3 (LIUGCR3) Table 127:: LIU Global Control Register 4 (LIUGCR4) Table 128:: LIU Global Control Register 5 (LIUGCR5) III REV. 1.0.1 Hex Address: 0xNF0B ..................... 141 Hex Address: 0xNF0C .................... 141 Hex Address: 0xNF0E ..................... 142 Hex Address: 0xNF0F ..................... 142 Hex Address: 0xNFE0 ............ 143 Hex Address: 0xNFE1 ............ 144 Hex Address: 0xNFE2 ............ 145 Hex Address: 0xNFE4 ............ 146 Hex Address: 0xNFE9 ............ 147 Hex Address: 0xNFEA ............ 148 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 DESCRIPTION OF THE CONTROL REGISTERS - T1 MODE All address on this register description is shown in HEX format. TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX Clock and Select Register CSR 0xN100 Line Interface Control Register LICR 0xN101 - 0xN102 - 0xN106 Framing Select Register FSR 0xN107 Alarm Generation Register AGR 0xN108 Synchronization MUX Register SMR 0xN109 TSDLSR 0xN10A FCR 0xN10B RSDLSR 0xN10C Receive Signaling Change Register 0 RSCR0 0xN10D Receive Signaling Change Register 1 RSCR1 0xN10E Receive Signaling Change Register 2 RSCR2 0xN10F - 0xN110 0xN111 Receive In-Frame Register RIFR 0xN112 Data Link Control Register 1 DLCR1 0xN113 Transmit Data Link Byte Count Register 1 TDLBCR1 0xN114 Receive Data Link Byte Count Register 1 RDLBCR1 0xN115 SBCR 0xN116 FIFO Latency Register FIFOLR 0xN117 DMA 0 (Write) Configuration Register D0WCR 0xN118 DMA 1 (Read) Configuration Register D1RCR 0xN119 ICR 0xN11A LAPDSR 0xN11B Customer Installation Alarm Generation Register CIAGR 0xN11C Performance Report Control Register PRCR 0xN11D Gapped Clock Control Register GCCR 0xN11E Transmit Interface Control Register TICR 0xN120 BERT Control & Status - Register 0 BERTCSR0 0xN121 Receive Interface Control Register RICR 0xN122 Control Registers (0xN100 - 0xN1FF) Reserved Transmit Signaling and Data Link Select Register Framing Control Register Receive Signaling & Data Link Select Register Reserved - E1 mode only Slip Buffer Control Register Interrupt Control Register LAPD Select Register 4 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX BERTCSR1 0xN123 LCCR0 0xN124 TLCR 0xN125 Receive Loopback Activation Code Register - Code 0 RLACR0 0xN126 Receive Loopback Deactivation Code Register - Code 0 RLDCR0 0xN127 Receive LoopCode Detection Switch RLCDS 0xN128 Defect Detection Enable Register DDER 0xN129 Loopback Code Control Register - Code 1 LCCR1 0xN12A Receive Loopback Activation Code Register - Code 1 RLACR1 0xN12B Receive Loopback Deactivation Code Register - Code 1 RLDCR1 0xN12C LCCR2 0xN12D Receive Loopback Activation Code Register - Code 2 RLACR2 0xN12E Receive Loopback Deactivation Code Register - Code 2 RLDCR2 0xN12F - 0xN130 - 0xN13F TLCGS 0xN140 LCTS 0xN141 TSPRMCR 0xN142 DLCR2 0xN143 Transmit Data Link Byte Count Register 2 TDLBCR2 0xN144 Receive Data Link Byte Count Register 2 RDLBCR2 0xN145 Loopback Code Control Register - Code 3 LCCR3 0xN146 Receive Loopback Activation Code Register - Code 3 RLACR3 0xN147 Receive Loopback Deactivation Code Register - Code 3 RLDCR3 0xN148 LCCR4 0xN149 Receive Loopback Activation Code Register - Code 4 RLACR4 0xN14A Receive Loopback Deactivation Code Register - Code 4 RLDCR4 0xN14B LCCR5 0xN14C Receive Loopback Activation Code Register - Code 5 RLACR5 0xN14D Receive Loopback Deactivation Code Register - Code 5 RLDCR5 0xN14E LCCR6 0xN14F Receive Loopback Activation Code Register - Code 6 RLACR6 0xN150 Receive Loopback Deactivation Code Register - Code 6 RLDCR6 0xN151 DLCR3 0xN153 BERT Control & Status - Register 1 Loopback Code Control Register - Code 0 Transmit Loopback Code Register Loopback Code Control Register - Code 2 Reserved - E1 mode only Transmit LoopCode Generation Switch Loopcode Timer Select Transmit SPRM and NPRM Control Register Data Link Control Register 2 Loopback Code Control Register - Code 4 Loopback Code Control Register - Code 5 Loopback Code Control Register - Code 6 Data Link Control Register 3 5 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX Transmit Data Link Byte Count Register 3 TDLBCR3 0xN154 Receive Data Link Byte Count Register 3 RDLBCR3 0xN155 Loopback Code Control Register - Code 7 LCCR7 0xN156 Receive Loopback Activation Code Register - Code 7 RLACR7 0xN157 Receive Loopback Deactivation Code Register - Code 7 RLDCR7 0xN158 BCR 0xN163 SSM BOC Control Register BOCCR 0xN170 SSM Receive FDL Register RFDLR 0xN171 SSM Receive FDL Match 1 Register RFDLMR1 0xN172 SSM Receive FDL Match 2 Register RFDLMR2 0xN173 SSM Receive FDL Match 3 Register RFDLMR3 0xN174 SSM Transmit FDL Register TFDLR 0xN175 SSM Transmit Byte Count Register TBCR 0xN176 Receive DS-0 Monitor Registers RDS0MR 0xN15F - 0xN1CF Transmit DS-0 Monitor Registers TDS0MR 0xN1D0 - 0xN1EF Device ID Register DEVID 0xN1FE Revision Number Register REVID 0xN1FF Transmit Channel Control Register 0-23 TCCR 0-23 0xN300 - 0xN317 Transmit User Code Register 0-23 TUCR 0-23 0xN320 - 0xN337 Transmit Signaling Control Register 0-23 TSCR 0-23 0xN340 - 0xN357 Receive Channel Control Register 0-23 RCCR 0-23 0xN360 - 0xN377 Receive User Code Register 0-23 RUCR 0-23 0xN380 - 0xN397 Receive Signaling Control Register 0-23 RSCR 0-23 0xN3A0 - 0xN3B7 Receive Substitution Signaling Register 0-23 RSSR 0-23 0xN3C0 - 0xN3D7 RSAR0-23 0xN500 0xN517 LAPDBCR0 0xN600 0xN660 LAPDBCR1 0xN700 0xN760 BERT Control Register Time Slot (payload) Control (0xN300 - 0xN3FF) Receive Signaling Array (0xN500 - 0xN51F) Receive Signaling Array Register 0 LAPDn Buffer 0 LAPD Buffer 0 Control Register LAPDn Buffer 1 LAPD Buffer 1 Control Register 6 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX Receive Line Code Violation Counter: MSB RLCVCU 0xN900 Receive Line Code Violation Counter: LSB RLCVCL 0xN901 Receive Frame Alignment Error Counter: MSB RFAECU 0xN902 Receive Frame Alignment Error Counter: LSB RFAECL 0xN903 Receive Severely Errored Frame Counter RSEFC 0xN904 Receive Synchronization Bit (CRC-6) Error Counter: MSB RSBBECU 0xN905 Receive Synchronization Bit (CRC-6) Error Counter: LSB RSBBECL 0xN906 Performance Monitor Reserved - E1 Mode Only 0xN907 - 0xN908 Receive Slip Counter RSC 0xN909 Receive Loss of Frame Counter RLFC 0xN90A Receive Change of Frame Alignment Counter RCOAC 0xN90B LAPD Frame Check Sequence Error counter 1 LFCSEC1 0xN90C PRBS bit Error Counter: MSB PBECU 0xN90D PRBS bit Error Counter: LSB PBECL 0xN90E TSC 0xN90F Excessive Zero Violation Counter: MSB EZVCU 0xN910 Excessive Zero Violation Counter: LSB EZVCL 0xN911 LAPD Frame Check Sequence Error counter 2 LFCSEC2 0xN91C LAPD Frame Check Sequence Error counter 3 LFCSEC3 0xN92C Block Interrupt Status Register BISR 0xNB00 Block Interrupt Enable Register BIER 0xNB01 Alarm & Error Interrupt Status Register AEISR 0xNB02 Alarm & Error Interrupt Enable Register AEIER 0xNB03 Framer Interrupt Status Register FISR 0xNB04 Framer Interrupt Enable Register FIER 0xNB05 Data Link Status Register 1 DLSR1 0xNB06 Data Link Interrupt Enable Register 1 DLIER1 0xNB07 Slip Buffer Interrupt Status Register SBISR 0xNB08 Slip Buffer Interrupt Enable Register SBIER 0xNB09 Receive Loopback code 0 Interrupt and Status Register RLCISR0 0xNB0A Receive Loopback code 0 Interrupt Enable Register RLCIER0 0xNB0B Transmit Slip Counter Interrupt Generation/Enable Register Address Map (0xNB00 - 0xNB41) 7 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX - 0xNB0C - 0xNB0D Excessive Zero Status Register EXZSR 0xNB0E Excessive Zero Enable Register EXZER 0xNB0F SS7 Status Register for LAPD 1 SS7SR1 0xNB10 SS7 Enable Register for LAPD 1 SS7ER1 0xNB11 RxLOS/CRC Interrupt Status Register RLCISR 0xNB12 RxLOS/CRC Interrupt Enable Register RLCIER 0xNB13 Receive Loopback code 1 Interrupt and Status Register RLCISR1 0xNB14 Receive Loopback code 1 Interrupt Enable Register RLCIER1 0xNB15 Data Link Status Register 2 DLSR2 0xNB16 Data Link Interrupt Enable Register 2 DLIER2 0xNB17 SS7 Status Register for LAPD 2 SS7SR2 0xNB18 SS7 Enable Register for LAPD 2 SS7ER2 0xNB19 Receive Loopback code 2 Interrupt and Status Register RLCISR2 0xNB1A Receive Loopback code 2 Interrupt Enable Register RLCIER2 0xNB1B Receive Loopback code 3 Interrupt and Status Register RLCISR3 0xNB1C Receive Loopback code 3 Interrupt Enable Register RLCIER3 0xNB1D Receive Loopback code 4 Interrupt and Status Register RLCISR4 0xNB1E Receive Loopback code 4Interrupt Enable Register RLCIER4 0xNB1F Receive Loopback code 5 Interrupt and Status Register RLCISR5 0xNB20 Receive Loopback code 5 Interrupt Enable Register RLCIER5 0xNB21 Receive Loopback code 6 Interrupt and Status Register RLCISR6 0xNB22 Receive Loopback code 6 Interrupt Enable Register RLCIER6 0xNB23 Receive Loopback code 7 Interrupt and Status Register RLCISR7 0xNB24 Receive Loopback code 7 Interrupt Enable Register RLCIER7 0xNB25 Data Link Status Register 3 DLSR3 0xNB26 Data Link Interrupt Enable Register 3 DLIER3 0xNB27 SS7 Status Register for LAPD 3 SS7SR3 0xNB28 SS7 Enable Register for LAPD 3 SS7ER3 0xNB29 Customer Installation Alarm Status Register CIASR 0xNB40 Customer Installation Alarm Interrupt Enable Register CIAIER 0xNB41 BOC Interrupt Status Register BOCISR 0xNB70 BOC Interrupt Enable Register BOCIER 0xNB71 Reserved - E1 Mode Only 8 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 1: REGISTER SUMMARY FUNCTION SYMBOL HEX - 0xNB72 - 0xNB73 BOC Unstable Interrupt Status Register BOCUSR 0xNB74 BOC Unstable Interrupt Enable Register BOCUER 0xNB75 LIU Channel Control Register 0 LIUCCR0 0x0FN0 LIU Channel Control Register 1 LIUCCR1 0x0FN1 LIU Channel Control Register 2 LIUCCR2 0x0FN2 LIU Channel Control Register 3 LIUCCR3 0x0FN3 LIU Channel Control Interrupt Enable Register LIUCCIER 0x0FN4 LIU Channel Control Status Register LIUCCSR 0x0FN5 LIU Channel Control Interrupt Status Register LIUCCISR 0x0FN6 LIU Channel Control Cable Loss Register LIUCCCCR 0x0FN7 LIU Channel Control Arbitrary Register 1 LIUCCAR1 0x0FN8 LIU Channel Control Arbitrary Register 2 LIUCCAR2 0x0FN9 LIU Channel Control Arbitrary Register 3 LIUCCAR3 0x0FNA LIU Channel Control Arbitrary Register 4 LIUCCAR4 0x0FNB LIU Channel Control Arbitrary Register 5 LIUCCAR5 0x0FNC LIU Channel Control Arbitrary Register 6 LIUCCAR6 0x0FND LIU Channel Control Arbitrary Register 7 LIUCCAR7 0x0FNE LIU Channel Control Arbitrary Register 8 LIUCCAR8 0x0FNF - 0x0F80 0x0FDF LIU Global Control Register 0 LIUGCR0 0x0FE0 LIU Global Control Register 1 LIUGCR1 0x0FE1 LIU Global Control Register 2 LIUGCR2 0x0FE2 LIU Global Control Register 3 LIUGCR3 0x0FE4 LIU Global Control Register 4 LIUGCR4 0x0FE9 LIU Global Control Register 5 LIUGCR5 0x0FEA - 0x0FEB 0x0FFF Reserved LIU Register Summary - Channel Control Registers Reserved LIU Register Summary - Global Control Registers Reserved 9 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 1.0 REGISTER DESCRIPTIONS - T1 MODE All address on this register description is shown in HEX format TABLE 2: CLOCK SELECT REGISTER(CSR) BIT FUNCTION TYPE DEFAULT HEX ADDRESS: 0XN100 DESCRIPTION-OPERATION 7 LCV Insert R/W 0 Line Code Violation Insertion This bit is used to force a Line Code Violation (LCV) on the transmit output of TTIP/TRING. A “0” to “1” transition on this bit will cause a single LCV to be inserted on the transmit output of TTIP/TRING. 6 Set T1 Mode R/W 0 T1 Mode select This bit is used to program the individual channel to operate in either T1 or E1 mode. 0 = Configures the selected channel to operate in E1 mode. 1 = Configures the selected channel to operate in T1 mode. 5 Sync All Transmitters to 8kHz R/W 0 Sync All Transmit Framers to 8kHz This bit permits the user to configure the Transmit T1 Framer block to synchronize its “transmit output” frame alignment with the 8kHz signal that is derived from the MCLK PLL, as described below. 0 - Disables the “Sync all Transmit Framers to 8kHz” feature. 1 - Enables the “Sync all Transmit Framers to 8kHz” feature. NOTE: This bit is only active if the MCLK PLL is used as the “Timing Source” for the Transmit T1 Framer” blocks. CSS[1:0] of this register allows users to select the transmit source of the framer. 4 Clock Loss Detect R/W 1 Clock Loss Detect Enable/Disable Select This bit enables a clock loss protection feature for the Framer whenever the recovered line clock is used as the timing source for the transmit section. If the LIU loses clock recovery, the Clock Distribution Block will detect this occurrence and automatically begin to use the internal clock derived from MCLK PLL as the Transmit source, until the LIU is able to regain clock recovery. 0 = Disables the clock loss protection feature. 1 = Enables the clock loss protection feature. NOTE: This bit needs to be enabled in order to detect the clock closs detection interrupt status (address: 0xNB00, bit 5) 3:2 Reserved R/W 00 Reserved 10 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 2: CLOCK SELECT REGISTER(CSR) BIT 1:0 FUNCTION CSS[1:0] REV. 1.0.1 HEX ADDRESS: 0XN100 TYPE DEFAULT DESCRIPTION-OPERATION R/W 01 Clock Source Select These bits select the timing source for the Transmit T1 Framer block. These bits can also determine the direction of TxSERCLK, TxSYNC, and TxMSYNC in base rate operation mode (1.544MHz Clock mode). In Base Rate (1.544MHz Clock Mode): CSS[1:0] 00/11 TRANSMIT SOURCE FOR THE TRANSMIT T1 FRAMER BLOCK Loop Timing Mode The recovered line clock is chosen as the timing source. 01 External Timing Mode The Transmit Serial Input Clock from the TxSERCLK_n input pin is chosen as the timing source. 10 Internal Timing Mode The MCLK PLL is chosen as the timing source. DIRECTION OF TXSERCLK Output Input Output NOTE: TxSYNC/TxMSYNC can be programmed as input or output depending on the setting of SYNC INV bit in Register Address 0xN109, bit 4. Please see Register Description for the Synchronization Mux Register (SMR - 0xN109) Table 8. NOTES: In High-Speed or multiplexed modes, TxSERCLK, TxSYNC, and TxMSYNC are all configured as INPUTS only. 11 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 3: LINE INTERFACE CONTROL REGISTER (LICR) BIT FUNCTION HEX ADDRESS: 0XN101 TYPE DEFAULT DESCRIPTION-OPERATION 7 FORCE_LOS R/W 0 Force Transmit LOS (To the Line Side) This bit permits the user to configure the transmit direction circuitry (within the channel) to transmit the LOS pattern to the remote terminal equipment, as described below. 0 - Configures the transmit direction circuitry to transmit “normal” traffic. 1 - Configures the transmit direction circuitry to transmit the LOS Pattern. 6 Reserved R/W 0 Single Rail Mode This bit can only be set if the LIU Block is also set to single rail mode. See Register 0xNFE0, bit 7. 0 - Dual Rail 1 - Single Rail LB[1:0] R/W 00 Framer Loopback Selection These bits are used to select any of the following loop-back modes for the framer section. For LIU loopback modes, see the LIU configuration registers. 5:4 3:2 Reserved R/W 0 LB[1:0] TYPES OF LOOPBACK SELECTED 00 Normal Mode (No LoopBack) 01 Framer Local LoopBack: When framer local loopback is enabled, the transmit PCM input data is looped back to the receive PCM output data. The receive input data at RTIP/RRING is ignored while an All Ones Signal is transmitted out to the line interface. 10 Framer Far-End (Remote) Line LoopBack: When framer remote loopback is enabled, the digital data enters the framer interface, however does not enter the framing blocks. The receive digital data from the LIU is allowed to pass through the LIU Decoder/ Encoder circuitry before returning to the line interface. 11 Framer Payload LoopBack: When framer payload loopback is enabled, the raw data within the receive time slots are looped back to the transmit framer block where the data is re-framed according to the transmit timing. Reserved 12 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 3: LINE INTERFACE CONTROL REGISTER (LICR) BIT 1 FUNCTION Encode B8ZS TYPE DEFAULT R/W 0 REV. 1.0.1 HEX ADDRESS: 0XN101 DESCRIPTION-OPERATION Encode AMI or B8ZS/HDB3 Line Code Select This bit enables or disables the B8ZS/HDB3 encoder on the transmit path. 0 = Enables the B8ZS encoder. 1 = Disables the B8ZS encoder. NOTE: When B8ZS encoder is disabled, AMI line code is used. 0 Decode AMI/B8ZS R/W 0 Decode AMI or B8ZS/HDB3 Line Code Select This bit enables or disables the B8ZS/HDB3 decoder on the receive path. 0 = Enables the B8ZS decoder. 1 = Disables the B8ZS decoder. NOTE: When B8ZS decoder is disabled, AMI line code is received. 13 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 4: FRAMING SELECT REGISTER (FSR) HEX ADDRESS: 0XN107 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 Signaling update on Superframe Boundaries R/W 0 Enable Robbed-Bit Signaling Update on Superframe Boundary on Both Transmit and Receive Direction This bit enables or disables robbed-bit signaling update on the superframe boundary for both the transmit and receive side of the framer. On the Receive Side: If signaling update is enabled, signaling data on the receive side (RxSIG pin and Signaling Array Register - RSAR) will be updated on the superframe boundary, otherwise, signaling data will be updated as soon as it is received. On the Transmit Side: If signaling update is enabled, any signaling data changes on the transmit side will be transmitted on the superframe boundary, otherwise, signaling data will be transmitted as soon as it is changed. 0 - Disables the signaling update feature for both transmit and receive. 1 - Enables the signaling update feature for both transmit and receive. 6 Force CRC Errors R/W 0 Force CRC Errors (To the Line Side) This bit permits the user to force the Transmit T1 Framer block to transmit CRC errors within the outbound T1 data-stream, as depicted below. 0 - Disables CRC error transmission on the outbound T1 stream. 1 - Enables CRC error transmission on the outbound T1 stream. 5 J1_MODE R/W 0 J1 Mode This bit is used to configure the device in J1 mode. Once the device is configured in J1 mode, the following two changes will happen: 1. CRC calculation is done in J1 format. The J1 CRC6 calculation is based on the actual values of all 4632 bits in a T1 multiframe including Fe bits instead of assuming all Fe bits to be a one in T1 format. 2. Receive and Transmit Yellow Alarm signal format is interpreted per the J1 standard. (J1-SF or J1-ESF) 0 - Configures the device in T1 mode. (Default) 1 - Configures the device in J1 mode. NOTE: Users can select between J1-SF or J1-ESF by setting this bit and the T1 Framing Mode Select Bits[2:0] (Bits 2-0 within this register). 4 ONEONLY R/W 0 Allow Only One Sync Candidate This bit is used to specify one of the synchronization criteria that the Receive T1 Framer block employs. 0 - Allows the Receive T1 Framer to select any one of the winners in the matching process when there are two or more valid synchronization patterns appear in the required time frame. 1 - Allows the Receive T1 Framer to declare success of match when there is only one candidate left in the required time frame. 14 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 4: FRAMING SELECT REGISTER (FSR) BIT 3 FUNCTION FASTSYNC HEX ADDRESS: 0XN107 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Faster Sync Algorithm This bit is used to specify one of the synchronization criteria that the Receive T1 Framer block employs. If this “Faster Sync Algorithm” is enabled, the Receive T1 Framer Block will declare synchronization earlier. The table below specifies the number of consecutive frames with correct F-bits that the T1 Receive framer must receive in order to declare “SYNC” when FASTSYNC is enabled or disabled. Framing FastSync =0 FastSync =1 ESF 96 48 SF 48 24 N 48 24 SLC 96 48 24 0 - Disables FASTSYNC feature. 1 - Enables FASTSYNC feature. 2-0 FSl[2:0] R/W 000 T1 Framing Mode Select [2:0] These three bits permit the user to select the exact T1 framing format that the channel is to operate in. Bit 2 is MSB and Bit 0 is LSB. The following table shows the five different framing formats that can be selected by configuring these three bits accordingly. NOTE: Changing Framing formats 'on the fly' will cause the Receive T1 Framer block to undergo a “Reframe” event. 15 Framing FS[2] FS[1] FS[0] ESF 0 X X SF 1 0 1 N 1 1 0 T1DM 1 1 1 SLC96 1 0 0 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 5: ALARM GENERATION REGISTER (AGR) BIT 7 FUNCTION HEX ADDRESS: 0XN108 TYPE DEFAULT Yellow Alarm - R/W One Second Rule 0 DESCRIPTION-OPERATION One-Second Yellow Alarm Rule Enforcement This bit is used to enforce the one-second yellow alarm rule according to the yellow alarm (RAI) transmission duration per the ANSI standards. If the one second alarm rule is enforced, the following will happen: 1. RAI will be transmitted for at least one second for both ESF and SF. 2. There must be a minimum of one second delay between termination of the first RAI and the initiation of a subsequent RAI. 3. ALARM_ENB bit (see description of bit 6 of this register) controls the duration of RAI. 4. YEL[0] & YEL[1] (see description of bits 5-4 of this register) controls the format of RAI. If the one second alarm rule is NOT enforced, the following will happen: 1. RAI will be transmitted for at least one second for ESF and SF. 2. Minimum one second delay between termination of the first RAI and the initiation of the subsequent RAI is NOT enforced. 3. YEL[0] and YEL[1] bits (see description of bits 5-4 of this register) are used to control the duration AND the format of RAI transmission. 0 - The one-second yellow alarm rule is NOT enforced. 1 - The one-second yellow alarm rule is enforced. NOTE: When setting this bit to ‘0’, yellow alarm transmission will be backward compatible with the XRT86L38 device. XRT86L38 does not support the one-second yellow alarm rule. 6 ALARM_ENB R/W 0 Yellow Alarm Transmission Enable This bit is used to control the duration of yellow alarm (RAI) when the one-second yellow alarm rule is enforced (bit 7 of this register set to’1’). When the one-second yellow alarm rule is not enforced (bit 7 of this register set to’0’), the duration of the RAI is controlled by the YEL[0] and YEL[1] bits (bits 5-4 of this register). If the one-second alarm rule is enforced: 0 - Stop the transmission of yellow alarm (see description of bits 5-4). 1 - Start the transmission of yellow alarm (see description of bits 5-4). NOTE: This bit has no function if the one second alarm rule is not enforced. 16 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 5: ALARM GENERATION REGISTER (AGR) BIT FUNCTION 5-4 YEL[1:0] HEX ADDRESS: 0XN108 TYPE DEFAULT R/W 00 REV. 1.0.1 DESCRIPTION-OPERATION Yellow Alarm (RAI) Duration and Format The exact function of these bits depends on whether or not the one-second yellow alarm rule is enforced. (Bit 7 of this register). The decoding of these bits are explained in Table 6 and Table 7 below. TABLE 6: YELLOW ALARM DURATION AND FORMAT WHEN ONE SECOND RULE IS NOT ENFORCED YEL[1:0] YELLOW ALARM DURATION AND FORMAT 00 Disable the transmission of yellow alarm 01 SF or N mode: RAI is transmitted as bit 2 = 0 (second MSB) in all DS0 data channel. T1DM mode: RAI is transmitted as Y-bit = 0 (6th bit in the SYNC byte). ESF mode: 1. If YEL[0] bit is set ’high’ for a duration shorter or equal to the time required to transmit 255 patterns of 1111_1111_0000_0000 on the 4-kbit/s data link bits (M1M12), RAI is transmitted for 255 patterns.of 1111_1111_0000_0000 (approximately 1 second) 2. If YEL[0] bit is set ’high’ for a duration longer than the time required to transmit 255 patterns of 1111_1111_0000_0000 on the 4-kbit/s data link bits (M1-M12), RAI transmission continues until YEL[0] bit is set ’low’. 3. If YEL[0] bit forms another pulse during the RAI transmission, it resets the pattern counter and extends the RAI duration for another 255 patterns of 1111_1111_0000_0000. (approximately 1 second) 10 SF mode: RAI is transmitted as a “1” in the Fs bit of frame 12 (This is RAI for J1 SF standard). T1DM mode: RAI is transmitted as Y-bit = 0 (6th bit in the SYNC byte). ESF mode: RAI is controlled by the duration of YEL[1] bit. This allows continuous RAI of any length. 11 SF, N, and T1DM mode: RAI format is the same as described above when YEL[1:0] is set to’01’. ESF mode: RAI duration is the same as described above when YEL[1:0] is set to’01’, except that format of RAI is transmitted as 255 patterns of 1111_1111_1111_1111 (sixteen ones) on the 4kbits/s data link bits instead of 255 patterns of 1111_1111_0000_0000. NOTE: 255 patterns of 1111_1111_1111_111 is the J1 ESF RAI standard) 17 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 5: ALARM GENERATION REGISTER (AGR) BIT FUNCTION 5-4 YEL[1:0] HEX ADDRESS: 0XN108 TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION (Continued) TABLE 7: YELLOW ALARM FORMAT WHEN ONE SECOND RULE IS ENFORCED YEL[1:0] YELLOW ALARM FORMAT 00 Disable the transmission of yellow alarm 01 SF or N mode: RAI is transmitted as bit 2 = 0 (second MSB) in all DS0 data channel. T1DM mode: RAI is transmitted as Y-bit = 0 (6th bit in the SYNC byte). ESF mode: YEL[1:0] controls the format of RAI. When YEL[1:0] is set to’01’, RAI is transmitted as 255 patterns of 1111_1111_0000_0000 on the 4kbit/s data link (M1-M12) (approximately 1 second). ALARM_ENB (Bit 6 of this register) controls the duration of RAI as described below: 1. If ALARM_ENB bit is set ’high’ for a duration shorter or equal to the time required to transmit 255 pattern of 1111_1111_0000_0000 on the 4-kbit/s data link (M1-M12), RAI is transmitted for 255 patterns. (approximately 1 second) 2. If ALARM_ENB bit is set ’high’ for a duration longer than the time required to transmit 255 patterns of 1111_1111_0000_0000 on the 4-kbit/s data link (M1-M12), RAI continues until ALARM_ENB bit is set ’low’. 3. If ALARM_ENB forms another pulse during an alarm transmission, it resets the pattern counter and extends the RAI duration for another 255 patterns.(approximately 1 second) NOTE: A minimum of one second delay between termination of the first RAI and the initiation of a subsequent RAI is enforced. 10 SF mode: RAI is transmitted as a “1” in the Fs bit of frame 12 (This is RAI for J1 SF standard). T1DM mode: RAI is transmitted as Y-bit = 0 (6th bit in the SYNC byte). ESF mode: RAI is controlled by the duration of ALARM_ENB bit. This allows continuous RAI of any length. 11 SF, N, and T1DM mode: RAI format is the same as described above when YEL[1:0] is set to’01’. ESF mode: RAI duration is the same as described above when YEL[1:0] is set to’01’, except that format of RAI is transmitted as 255 patterns of 1111_1111_1111_1111 on the 4kbits/s data link bits (J1 ESF standard) instead of 255 patterns of 1111_1111_0000_0000. 18 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 5: ALARM GENERATION REGISTER (AGR) BIT FUNCTION 3-2 Transmit AIS Pattern Select[1:0] HEX ADDRESS: 0XN108 TYPE DEFAULT R/W 00 REV. 1.0.1 DESCRIPTION-OPERATION Transmit AIS Pattern Select[1:0]: These two bits permit the user to do the following. 1. To select the appropriate AIS Pattern that the Transmit T1 Framer block will transmit to the remote terminal equipment, and 2. To command (via Software Control) the Transmit T1 Framer block to transmit that particular AIS Pattern to the remote terminal equipment, as depicted below. AISG[1:0] TYPES OF AIS PATTERNS TRANSMITTED 00/10 Disable AIS Alarm Generation The Transmit T1 Framer block will transmit “normal” T1 traffic to the remote terminal equipment. 01 Enable Unframed AIS Alarm Generation Transmit T1 Framer block will transmit an Unframed All Ones Pattern, as an AIS Pattern. 11 Enable Framed AIS Alarm Generation Transmit T1 Framer block will transmit a Framed, All Ones Pattern, as the AIS Pattern. NOTE: For normal operation (e.g., to configure the Transmit T1 Framer block to transmit normal T1 traffic) the user should set this bit to “[X, 0]” 1-0 AIS Defect Declaration Criteria [1:0] R/W 00 AIS Defect Declaration Criteria[1:0]: These bits permit the user to specify the types of AIS Patterns that the Receive T1 Framer block must detect before it will declare the AIS defect condition. AISD[1:0] 00/10 AIS Defect Declaration Criteria AIS Detection Disabled AIS Defect Condition will NOT be declared. 01 Enable Unframed and Framed AIS Alarm Detection ReceiveT1 Framer block will detect both Unframed and Framed AIS pattern 11 Enable Framed AIS Alarm Detection Receive T1 Framer block will detect only Framed AIS pattern 19 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 8: SYNCHRONIZATION MUX REGISTER (SMR) BIT FUNCTION 7 Reserved 6 MFRAMEALIGN HEX ADDRESS: 0XN109 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Transmit Multiframe Sync Alignment This bit forces Transmit T1 framer block to align with the backplane multiframe boundary (TxMSYNC_n). 0 = Do not force the transmit T1 framer block to align with the TxMSYNC signal. 1 = Force the transmit T1 framer block to align with the TxMSYNC signal. NOTE: This bit is not used in base rate (1.544MHz Clock) mode. 5 MSYNC R/W O Transmit Super Frame Boundary This bit provides an option to use the transmit single frame boundary (TxSYNC) as the transmit multi-frame boundary (TxMSYNC) in high speed or multiplexed modes. In 1.544MHz clock mode (base rate), the TxMSYNC is used as the transmit superframe boundary, in other clock modes (i.e. high speed or multiplexed modes), TxMSYNC is used as an input transmit clock for the backplane interface. 0 = Configures the TxSYNC as a single frame boundary. 1 = Configures the TxSYNC as a superframe boundary (TxMSYNC) in high-speed or multiplexed mode. NOTE: This bit is not used in base rate (1.544MHz Clock) mode. 20 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 8: SYNCHRONIZATION MUX REGISTER (SMR) BIT 4 FUNCTION Transmit Frame Sync Select REV. 1.0.1 HEX ADDRESS: 0XN109 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit Frame Sync Select This bit permits the user to configure the System-Side Terminal Equipment or the T1 Transmit Framer to dictate whenever the Transmit T1 Framer block will initiate its generation and transmission of the very next T1 frame. If the system side controls, then all of the following will be true. 1. The corresponding TxSync_n and TxMSync_n pins will function as input pins. 2. The Transmit T1 Framer block will initiate its generation of a new T1 frame whenever it samples the corresponding “TxSync_n” input pin “high” (via the TxSerClk_n input clock signal). 3. The Transmit T1 Framer block will initiate its generation of a new Multiframe whenever it samples the corresponding “TxMSync_n” input pin “high”. This bit can also be used to select the direction of the transmit single frame boundary (TxSYNC) and multi-frame boundary (TxMSYNC) depending on whether TxSERCLK is chosen as the timing source for the transmit section of the framer. (CSS[1:0] = 01 in register 0xN100) If TxSERCLK is chosen as the timing source: 0 = Configures TxSYNC and TxMSYNC as inputs. (System Side Controls) 1 = Configures TxSYNC and TxMSYNC as outputs. (Chip Controls) If either Recovered Line Clock, MCLK PLL is chosen as the timing source: 0 = Configures TxSYNC and TxMSYNC as outputs. (Chip Controls) 1 = Configures TxSYNC and TxMSYNC as inputs. (System Side Controls) NOTE: TxSERCLK is chosen as the transmit clock if CSS[1:0] of the Clock Select Register (Register Address: 0xN100) is set to b01. Recovered Clock is chosen as the transmit clock if CSS[1:0] is set to b00 or b11; Internal Clock is chosen as the transmit clock if CSS[1:0] is set to b10. 3 - 2 Reserved - - Reserved 21 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 8: SYNCHRONIZATION MUX REGISTER (SMR) BIT FUNCTION HEX ADDRESS: 0XN109 TYPE DEFAULT DESCRIPTION-OPERATION 1 CRC-6 Bits Source Select R/W 0 CRC-6 Bits Source Select This bit permits the user to specify the source of the CRC-6 bits, within the outbound T1 data-stream, as depicted below. 0 - Configures the Transmit T1 Framer block to internally compute and insert the CRC-6 bits within the outbound T1 data-stream. 1 - Configures the Transmit T1 Framer block to externally accept data from the TxSer_n input pin, and to insert this data into the CRC6 bits within the outbound T1 data-stream. This bit is ignored if CRC Multiframe Alignment is disabled 0 Framing Bits Source Select R/W 0 Framing Bits Source Select This bit is used to specify the source for the Framing bits that will be inserted into the outbound T1 frames. The Framing bits can be generated internally or inserted from the transmit serial input pin. (TxSER_n input pin) 0 = Configures the Transmit T1 Framer block to internally generate and insert the Framing bits into the outbound T1 data stream. 1 = Configures the Transmit T1 Framer block to externally accept framing bits from the TxSer_n input pin, and to insert this data to the outbound T1 data-stream. 22 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 9: TRANSMIT SIGNALING AND DATA LINK SELECT REGISTER (TSDLSR) BIT FUNCTION TYPE DEFAULT HEX ADDRESS:0XN10A DESCRIPTION-OPERATION 7 Reserved - - Reserved 6 Reserved - - Reserved R/W 00 5-4 TxDLBW[1:0] REV. 1.0.1 Transmit Data Link Bandwidth[1:0] These two bits are used to select the bandwidth for data link message transmission. Data Link messages can be transmitted at a 4kHz rate or at a 2kHz rate on odd or even framing bits depending on the configuration of these three bits. The table below specifies the four different configurations. TXDLBW[1:0] TRANSMIT DATA LINK BANDWIDTH SELECTED 00 Data link bits are inserted in every frame. Facility Data Link Bits (FDL) is a 4kHz data link channel. 01 Data link bits are inserted in every other frame. Facility Data Link Bits (FDL) is a 2kHz data link channel carried by odd framing bits (Frames 1,5,9.....) 10 Data link bits are inserted in every other frame. Facility Data Link Bits (FDL) is a 2kHz data link channel carried by even framing bits (Frames 3,7,11.....) 11 Reserved NOTE: This bit only applies to T1 ESF framing format. For SLC96 and N framing formats, FDL is a 4kHz data link channel. For T1DM, FDL is a 8kHz data link channel. 3-2 TxDE[1:0] R/W 00 Transmit D/E TimeSlot Source Select[1:0]: These two bits specify the source for transmit D/E time slots. The table below shows the different sources from which D/E time slots can be inserted. TXDE[1:0] SOURCE FOR TRANSMIT D/E TIMESLOTS 00 TxSER_n input pin - The D/E time slots are inserted from the transmit serial data input pin (TxSER_n) pin. 01 Transmit LAPD Controller - The D/E time slots are inserted from LAPD Controller. 10 Reserved 11 TxFRTD_n - The D/E time slots are inserted from the transmit fractional input pin. 23 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 9: TRANSMIT SIGNALING AND DATA LINK SELECT REGISTER (TSDLSR) BIT FUNCTION 1-0 TxDL[1:0] HEX ADDRESS:0XN10A TYPE DEFAULT DESCRIPTION-OPERATION R/W 00 Transmit Data Link Source Select [1:0] These two bits specify the source for data link bits that will be inserted in the outbound T1 frames. The table below shows the three different sources from which data link bits can be inserted. TXDL[1:0] SOURCE FOR DATA LINK BITS 00 Transmit LAPD Controller #1 / SLC96 Buffer - The Data Link bits are inserted from the Transmit LAPD Controller #1 or SLC96 Buffer. NOTE: LAPD Controller #1 is the only LAPD controller that can be used to transport LAPD messages through the data link bits 01 TxSER_n input pin - The Data Link bits are inserted from the transmit serial data input pin (TxSER_n) pin. 10 TxOH_n input pin - The Data Link bits are inserted from the transmit overhead input pin. (TxOH_n) 11 Data Link bits are forced to 1. 24 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 10: FRAMING CONTROL REGISTER (FCR) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN10B TYPE DEFAULT DESCRIPTION-OPERATION 7 Reframe R/W 0 Force Reframe A ‘0’ to ‘1’ transition will force the Receive T1 Framer to restart the synchronization process. This bit field is automatically cleared (set to 0) after frame synchronization is reached. 6 Framing with CRC Checking R/W 1 Framing with CRC Checking in ESF This bit permits the user to include CRC verification as a part of the “T1/ESF Framing Alignment” process. If the user enables this feature, then the Receive T1 Framer block will also check and verify that the incoming T1 data-stream contains correct CRC data, prior to declaring the “In-Frame” condition. 0 - CRC Verification is NOT included in the “Framing Alignment” process. 1 - Receive T1 Framer block will also check for correct CRC values prior to declaring the “In-Frame” condition. R/W 000 LOF Defect Declaration Tolerance[2:0]: These bits along with the LOF_RANGE[2:0] bits are used to define the LOF Defect Declaration criteria. The Receive T1 Framer block will declare the LOF defect condition anytime it detects “LOF_Tolerance[2:0]” out of “LOF_Range[2:0] framing bit errors within the incoming T1 data-stream. The recommended LOF_TOLR value is 2. 5-3 LOF Tolerance[2:0] NOTE: A “0” value for LOF_TOLR is internally blocked. A LOF_TOLR value must be specified. 2-0 LOF_Range[2:0] R/W 011 LOF Defect Declaration Range[2:0]: These bits along with the “LOF_Tolerance[2:0] bits are used to define the “LOF Defect Declaration” criteria. The Receive T1 Framer block will declare the LOF Defect condition anytime it has received “LOF_Tolerance[2:0] out of “LOF_Range[2:0] framing bit errors, within the incoming T1 data-stream. The recommended LOF_ANG value is 5. NOTE: A “0” value for LOF_RANG is internally blocked. A LOF_RANG value must be specified. 25 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 11: RECEIVE SIGNALING & DATA LINK SELECT REGISTER (RSDLSR) BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 Reserved - - Reserved 6 Reserved - - Reserved R/W 00 5-4 RxDLBW[1:0] HEX ADDRESS: 0XN10C Receive Data Link Bandwidth[1:0]: These two bits select the bandwidth for data link message reception. Data Link messages can be received at a 4kHz rate or at a 2kHz rate on odd or even framing bits depending on the configuration of these bits. The table below specifies the different configurations. RXDLBW[1:0] RECEIVE DATA LINK BANDWIDTH SELECTED 00 Received Data link bits are extracted in every frame. Facility Data Link Bits (FDL) is a 4kHz data link channel. 01 Received Data link bits are extracted in every other frame. Facility Data Link Bits (FDL) is a 2kHz data link channel carried by odd framing bits (Frames 1,5,9.....) 10 Received Data link bits are extracted in every other frame. Facility Data Link Bits (FDL) is a 2kHz data link channel carried by even framing bits (Frames 3,7,11.....) 11 Reserved NOTE: This bit only applies to T1 ESF framing format. For SLC96 and N framing formats, FDL is a 4kHz data link channel. For T1DM, FDL is a 8kHz data link channel. 3-2 RxDE[1:0] R/W 00 Receive D/E Time-Slot Destination Select[1:0]: These bits permit the user to specify the “destination” circuitry that will receive and process the D/E-Time-slot within the incoming T1 datastream. DESTINATION CIRCUITRY FOR RECEIVE D/E TIME-SLOT RXDE[1:0] 00 RxSER_n output pin - The D/E time slots are output to the receive serial data output pin (RxSER_n) pin. 01 Receive LAPD Controller Block - The D/E time slots are output to Receive LAPD Controller Block. 10 Reserved 11 RxFRTD_n output pin- The D/E time slots are output to the receive fractional output pin. 26 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 11: RECEIVE SIGNALING & DATA LINK SELECT REGISTER (RSDLSR) BIT FUNCTION 1-0 RxDL[1:0] TYPE DEFAULT R/W 00 REV. 1.0.1 HEX ADDRESS: 0XN10C DESCRIPTION-OPERATION Receive Data-Link Destination Select[1:0]: These bits specify the destination circuitry, that is used to process the Data-Link data, within the incoming T1 data-stream. RXDL[1:0] 00 DESTINATION CIRCUITRY FOR RECEIVE DATA-LINK Receive LAPD Controller Block # 1 and RxSER_n - The Data Link bits are routed to the Receive LAPD Controller block #1 and the RxSER_n output pin NOTE: LAPD Controller #1 is the only LAPD controller that can be used to extract LAPD messages through the data link bits 01 RxSER_n- The Data Link bits are routed to the RxSER_n output pin. 10 RxOH_n and RxSER_n - The Data Link bits are routed to the RxOH_n and RxSER_n output pins. 11 Data Link bits are forced to 1. 27 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 12: RECEIVE SIGNALING CHANGE REGISTER 0 (RSCR 0) BIT FUNCTION TYPE DEFAULT 7 Ch. 0 RUR 0 6 Ch. 1 RUR 0 5 Ch.2 RUR 0 4 Ch.3 RUR 0 3 Ch.4 RUR 0 2 Ch.5 RUR 0 1 Ch.6 RUR 0 0 Ch.7 RUR 0 HEX ADDRESS: 0XN10D DESCRIPTION-OPERATION These bits indicate whether the Channel Associated signaling data, associated with Time-Slots 0 through 7 within the incoming T1 datastream, has changed since the last read of this register, as depicted below. 0 - CAS data (for Time-slots 0 through 7) has NOT changed since the last read of this register. 1 - CAS data (for Time-slots 0 through 7) HAS changed since the last read of this register. NOTES: This register is only active if the incoming T1 data-stream is using Channel Associated Signaling. TABLE 13: RECEIVE SIGNALING CHANGE REGISTER 1(RSCR 1) 0XN10E BIT FUNCTION HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION These bits indicate whether the Channel Associated signaling data, associated with Time-Slots 8 through 15 within the incoming T1 datastream, has changed since the last read of this register, as depicted below. 0 - CAS data (for Time-slots 8 through 15) has NOT changed since the last read of this register. 1 - CAS data (for Time-slots 8 through 15) HAS changed since the last read of this register. This register is only active if the incoming T1 data-stream is using Channel Associated Signaling. 7 Ch.8 RUR 0 6 Ch.9 RUR 0 5 Ch.10 RUR 0 4 Ch.11 RUR 0 3 Ch.12 RUR 0 2 Ch.13 RUR 0 1 Ch.14 RUR 0 0 Ch.15 RUR 0 TABLE 14: RECEIVE SIGNALING CHANGE REGISTER 2 (RSCR 2) 0XN10F BIT FUNCTION HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION These bits indicate whether the Channel Associated signaling data, associated with Time-Slots 16 through 23 within the incoming T1 data-stream, has changed since the last read of this register, as depicted below. 0 - CAS data (for Time-slots 16 through 23) has NOT changed since the last read of this register. 1 - CAS data (for Time-slots 16 through 23) HAS changed since the last read of this register. 7 Ch.16 RUR 0 6 Ch.17 RUR 0 5 Ch.18 RUR 0 4 Ch.19 RUR 0 3 Ch.20 RUR 0 2 Ch.21 RUR 0 1 Ch.22 RUR 0 0 Ch.23 RUR 0 NOTE: This register is only active if the incoming T1 data-stream is using Channel Associated Signaling. 28 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 15: RECEIVE IN FRAME REGISTER (RIFR) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN112 TYPE DEFAULT DESCRIPTION-OPERATION 7 In Frame RO 0 In Frame State This READ-ONLY bit indicates whether the Receive T1 Framer block is currently declaring the “In-Frame” condition with the incoming T1 datastream. 0 - Indicates that the Receive T1 Framer block is currently declaring the LOF (Loss of Frame) Defect condition. 1 - Indicates that the Receive T1 Framer block is currently declaring itself to be in the “In-Frame” condition. 6 Reserved - - Reserved (For E1 Mode Only) 5 AIS_Ingress R/W 0 AIS Ingress Generation This bit is used to send an AIS signal (unframed all ones) on the receiver output RxSER. 0 - Disabled 1 - Rx AIS Ingress Generation Enabled 4 FRAlarmMask R/W 0 Framer Alarm Mask This bit can be used to mask the alarms associated with the Framing Mode that is selected. Regardless of the framing mode, this bit will mask to following alarms: LOF, IF, COFA, COMFA, FE, SE, and FMD. By default, the alarms are NOT masked. 0 - Disabled 1 - Framing Alarms Masked 3 DS0Yel R/W 0 DS-0 Yellow Alarm Generation (T1 Mode Only) This bit is used to send a DS-0 Yellow alarm to TTip/TRing Egress direction regardless of what framing format is used if bit 2 in this register is set to "0". If bit 2 is set to "1", then the Yellow Alarm is sent to RxSER on the Ingress side. DS-0 Yellow Alarm is defined as bit 2 = 0 (second MSB) in all DS-0 data channels. 0 - Disabled 1 - DS-0 Yellow Alarm Generation Enabled 2 DS0Yel_Switch R/W 0 DS-0 Yellow Alarm Switch Bit (T1 Mode Only) This bit is used to set the direction of the DS-0 Yellow Alarm as described in bit 3 of this register. 0 - DS-0 Yellow Egress (TTip/TRing) Generation 1 - DS-0 Yellow Ingress (RxSER) Generation - - Reserved (For E1 Mode Only) 1-0 Reserved 29 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 16: DATA LINK CONTROL REGISTER (DLCR1) BIT FUNCTION HEX ADDRESS: 0XN113 TYPE DEFAULT DESCRIPTION-OPERATION 7 SLC-96 Data Link Enable R/W 0 SLC®96 DataLink Enable This bit permits the user to configure the channel to support the transmission and reception of the “SLC-96 type” of data-link message. 0 - Channel does not support the transmission and reception of “SLC-96” type of data-link messages. Regular SF framing bits will be transmitted. 1 - Channel supports the transmission and reception of the “SLC96” type of data-link messages. This bit is only active if the channel has been configured to operate in either the SLC-96 or the ESF Framing formats. 6 MOS ABORT Disable R/W 0 MOS ABORT Disable: This bit permits the user to either enable or disable the “Automatic MOS ABORT” feature within Transmit HDLC Controller # 1. If the user enables this feature, then Transmit HDLC Controller block # 1 will automatically transmit the ABORT Sequence (e.g., a zero followed by a string of 7 consecutive “1s”) whenever it abruptly transitions from transmitting a MOS type of message, to transmitting a BOS type of message. If the user disables this feature, then the Transmit HDLC Controller Block # 1 will NOT transmit the ABORT sequence, whenever it abruptly transitions from transmitting a MOS-type of message to transmitting a BOS-type of message. 0 - Enables the “Automatic MOS Abort” feature 1 - Disables the “Automatic MOS Abort” feature 5 Rx_FCS_DIS R/W 0 Receive Frame Check Sequence (FCS) Verification Enable/Disable This bit permits the user to configure the Receive HDLC Controller Block # 1 to compute and verify the FCS value within each incoming LAPD message frame. 0 - Enables FCS Verification 1 - Disables FCS Verification 4 AutoRx R/W 0 Auto Receive LAPD Message This bit configures the Receive HDLC Controller Block #1 to discard any incoming BOS or LAPD Message frame that exactly match which is currently stored in the Receive HDLC1 buffer. 0 = Disables this “AUTO DISCARD” feature 1 = Enables this “AUTO DISCARD” feature. 3 Tx_ABORT R/W 0 Transmit ABORT This bit configures the Transmit HDLC Controller Block #1 to transmit an ABORT sequence (string of 7 or more consecutive 1’s) to the Remote terminal. 0 - Configures the Transmit HDLC Controller Block # 1 to function normally (e.g., not transmit the ABORT sequence). 1 - Configures the Transmit HDLC Controller block # 1 to transmit the ABORT Sequence. 30 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 16: DATA LINK CONTROL REGISTER (DLCR1) BIT 2 FUNCTION Tx_IDLE Tx_FCS_EN HEX ADDRESS: 0XN113 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit Idle (Flag Sequence Byte) This bit configures the Transmit HDLC Controller Block #1 to unconditionally transmit a repeating string of Flag Sequence octets (0X7E) in the data link channel to the Remote terminal. In normal conditions, the Transmit HDLC Controller block will repeatedly transmit the Flag Sequence octet whenever there is no MOS message to transmit to the remote terminal equipment. However, if the user invokes this “Transmit Idle Sequence” feature, then the Transmit HDLC Controller block will UNCONDITIONALLY transmit a repeating stream of the Flag Sequence octet (thereby overwriting all outbound MOS data-link messages). 0 - Configures the Transmit HDLC Controller Block # 1 to transmit data-link information in a “normal” manner. 1 - Configures the Transmit HDLC Controller block # 1 to transmit a repeating string of Flag Sequence Octets (0x7E). NOTE: 1 REV. 1.0.1 R/W 0 This bit is ignored if the Transmit HDLC1 controller is operating in the BOS Mode - bit 0 (MOS/BOS) within this register is set to 0. Transmit LAPD Message with Frame Check Sequence (FCS) This bit permits the user to configure the Transmit HDLC Controller block # 1 to compute and append FCS octets to the “back-end” of each outbound MOS data-link message. 0 - Configures the Transmit HDLC Controller block # 1 to NOT compute and append the FCS octets to the back-end of each outbound MOS data-link message. 1 - Configures the Transmit HDLC Controller block # 1 TO COMPUTE and append the FCS octets to the back-end of each outbound MOS data-link message. NOTE: This bit is ignored if the transmit HDLC1 controller has been configured to operate in the BOS mode - bit 0 (MOS/BOS) within this register is set to 0. 0 MOS/BOS R/W 0 Message Oriented Signaling/Bit Oriented Signaling Send This bit permits the user to enable LAPD transmission through HDLC Controller Block # 1 using either BOS (Bit-Oriented Signaling) or MOS (Message-Oriented Signaling) frames. 0 - Transmit HDLC Controller block # 1 BOS message Send. 1 - Transmit HDLC Controller block # 1 MOS message Send. NOTE: This is not an Enable bit. This bit must be set to "0" each time a BOS is to be sent. 31 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 17: TRANSMIT DATA LINK BYTE COUNT REGISTER (TDLBCR1) BIT 7 FUNCTION TxHDLC1 BUFAvail/ BUFSel HEX ADDRESS: 0XN114 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit HDLC1 Buffer Available/Buffer Select This bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. If the user is writing data into this register bit: 0 - Configures the Transmit HDLC1 Controller to read out and transmit the data, residing within “Transmit HDLC1 Buffer # 0", via the Data Link channel to the remote terminal equipment. 1 - Configures the Transmit HDLC1 Controller to read out and transmit the data, residing within the “Transmit HDLC1 Buffer #1”, via the Data Link channel to the remote terminal equipment. If the user is reading data from this register bit: 0 - Indicates that “Transmit HDLC1 Buffer # 0" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC1 Message Buffer, he/she should proceed to write this message into “Transmit HDLC1 Buffer # 0" - Address location: 0xN600. 1 - Indicates that “Transmit HDLC1 Buffer # 1" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC1 Message Buffer, he/she should proceed to write this message into “Transmit HDLC1 Buffer # 1" - Address location: 0xN700. NOTE: If one of these Transmit HDLC1 buffers contain a message which has yet to be completely read-in and processed for transmission by the Transmit HDLC1 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. Changing this bit to the inuse buffer is not permitted. 6-0 TDLBC[6:0] R/W 0000000 Transmit HDLC1 Message - Byte Count The exact function of these bits depends on whether the Transmit HDLC 1 Controller is configured to transmit MOS or BOS messages to the Remote Terminal Equipment. In BOS MODE: These bit fields contain the number of repetitions the BOS message must be transmitted before the Transmit HDLC1 controller generates the Transmit End of Transfer (TxEOT) interrupt and halts transmission. If these fields are set to 00000000, then the BOS message will be transmitted for an indefinite number of times. In MOS MODE: These bit fields contain the length, in number of octets, of the message to be transmitted. The length of MOS message specified in these bits include header bytes such as the SAPI, TEI, Control field, however, it does not include the FCS bytes. 32 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 18: RECEIVE DATA LINK BYTE COUNT REGISTER (RDLBCR1) BIT 7 FUNCTION RBUFPTR 6-0 RDLBC[6:0] REV. 1.0.1 HEX ADDRESS: 0XN115 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Receive HDLC1 Buffer-Pointer This bit Identifies which Receive HDLC1 buffer contains the most recently received HDLC1 message. 0 - Indicates that Receive HDLC1 Buffer # 0 contains the contents of the most recently received HDLC message. 1 - Indicates that Receive HDLC1 Buffer # 1 contains the contents of the most recently received HDLC message. R/W 0000000 Receive HDLC Message - byte count The exact function of these bits depends on whether the Receive HDLC Controller Block #1 is configured to receive MOS or BOS messages. In BOS Mode: These seven bits contain the number of repetitions the BOS message must be received before the Receive HDLC1 controller generates the Receive End of Transfer (RxEOT) interrupt. If these bits are set to “0000000”, the message will be received indefinitely and no Receive End of Transfer (RxEOT) interrupt will be generated. In MOS Mode: These seven bits contain the size in bytes of the HDLC1 message that has been received and written into the Receive HDLC buffer. The length of MOS message shown in these bits include header bytes such as the SAPI, TEI, Control field, AND the FCS bytes. 33 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 19: SLIP BUFFER CONTROL REGISTER (SBCR) BIT 7 FUNCTION TYPE DEFAULT TxSB_ISFIFO R/W 0 HEX ADDRESS: 0XN116 DESCRIPTION-OPERATION Transmit Slip Buffer Mode This bit permits the user to configure the Transmit Slip Buffer to function as either “Slip-Buffer” Mode, or as a “FIFO”, as depicted below. 0 - Configures the Transmit Slip Buffer to function as a “Slip-Buffer”. 1 - Configures the Transmit Slip Buffer to function as a “FIFO”. NOTE: Transmit slip buffer is only used in high-speed or multiplexed mode where TxSERCLKn must be configured as inputs only. Users must make sure that the “Transmit Direction” timing (i.e. TxMSYNC) and the TxSerClk input clock signal are synchronous to prevent any transmit slips from occuring. NOTE: The data latency is dictated by FIFO Latency in the FIFO Latency Register (register 0xN117). 6-5 Reserved - - Reserved 4 SB_FORCESF R/W 0 Force Signaling Freeze This bit permits the user to freeze any signaling update on the RxSIGn output pin as well as the Receive Signaling Array Register -RSAR (0xN5000xN51F) until this bit is cleared. 0 = Signaling on RxSIG and RSAR is updated immediately. 1 = Signaling on RxSIG and RSAR is not updated until this bit is set to ‘0’. 3 SB_SFENB R/W 0 Signal Freeze Enable Upon Buffer Slips This bit enables signaling freeze for one multiframe after the receive buffer slips. If signaling freeze is enabled, then the “Receive Channel” will freeze all signaling updates on RxSIG pin and RSAR (0xN500-0xN51F) for at least “onemultiframe” period, after a “slip-event” has been detected within the “Receive Slip Buffer”. 0 = Disables signaling freeze for one multi-frame after receive buffer slips. 1 = Enables signaling freeze for one multi-frame after receive buffer slips. 2 SB_SDIR R/W 1 Slip Buffer (RxSync) Direction Select This bit permits user to select the direction of the receive frame boundary (RxSYNC) signal if the receive buffer is enabled. (i.e. SB_ENB[1:0] = 01 or 10). If slip buffer is bypassed, RxSYNC is always an output pin. 0 = Selects the RxSync signal as an output 1 = Selects the RxSync signal as an input 34 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 19: SLIP BUFFER CONTROL REGISTER (SBCR) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN116 TYPE DEFAULT DESCRIPTION-OPERATION Receive Slip Buffer Mode Select These bits select modes of operation for the receive slip buffer. These two bits also select the direction of RxSERCLK and RxSYNC in base clock rate (2.048MHz). The following table shows the corresponding slip buffer modes as well as the direction of the RxSYNC/RxSERCLK according to the setting of these two bits. 1 SB_ENB(1) R/w 0 0 SB_ENB(0) R/W 1 SB_ENB RECEIVE SLIP BUFFER DIRECTION OF MODE SELECT RXSERCLK [1:0] 00/11 DIRECTION OF RXSYNC Receive Slip Buffer is Output bypassed Output 01 Slip Buffer Mode Input Depends on the setting of SB_SDIR (bit 2 of this register) If SB_SDIR = 0: RxSYNC = Output If SB_SDIR = 1: RxSYNC = Input 10 FIFO Mode. Input FIFO data latency can be programmed by the 'FIFO Latency Register' (Address = 0xN117). Depends on the setting of SB_SDIR (bit 2 of this register) If SB_SDIR = 0: RxSYNC = Output If SB_SDIR = 1: RxSYNC = Input NOTE: Users must make sure that the RxSerClk input pin is synchronized to the Recovered Clock signal for this particular channel to prevent any buffer slips from occurring. TABLE 20: FIFO LATENCY REGISTER (FFOLR) BIT FUNCTION 7-5 Reserved 4-0 Rx Slip Buffer FIFO Latency[4:0] TYPE DEFAULT - - R/W 00100 HEX ADDRESS: 0XN117 DESCRIPTION-OPERATION Reserved Receive Slip Buffer FIFO Latency[4:0]: These bits permit the user to specify the “Receive Data” Latency (in terms of RxSerClk_n clock periods), whenever the Receive Slip Buffer has been configured to operate in the “FIFO” Mode. NOTE: These bits are only active if the Receive Slip Buffer has been configured to operate in the FIFO Mode. 35 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 21: DMA 0 (WRITE) CONFIGURATION REGISTER (D0WCR) BIT FUNCTION HEX ADDRESS: 0XN118 TYPE DEFAULT DESCRIPTION-OPERATION 7 DMA0 RST R/W 0 DMA_0 Reset This bit resets the transmit DMA (Write) channel 0. 0 = Normal operation. 1 = A zero to one transition resets the transmit DMA (Write) channel 0. 6 DMA0 ENB R/W 0 DMA_0 Enable This bit enables the transmit DMA_0 (Write) interface. After a transmit DMA is enabled, DMA transfers are only requested when the transmit buffer status bits indicate that there is space for a complete message or cell. The DMA write channel is used by the external DMA controller to transfer data from the external memory to the HDLC buffers within the T1 Framer. The DMA Write cycle starts by T1 Framer asserting the DMA Request (REQ0) ‘low’, then the external DMA controller should drive the DMA Acknowledge (ACK0) ‘low’ to indicate that it is ready to start the transfer. The external DMA controller should place new data on the Microprocessor data bus each time the Write Signal is Strobed low if the WR is configured as a Write Strobe. If WR is configured as a direction signal, then the external DMA controller would place new data on the Microprocessor data bus each time the Read Signal (RD) is Strobed low. 0 = Disables the transmit DMA_0 (Write) interface 1 = Enables the transmit DMA_0 (Write) interface 5 WR TYPE R/W 0 Write Type Select This bit selects the function of the WR signal. 0 = WR functions as a direction signal (indicates whether the current bus cycle is a read or write operation) and RD functions as a data strobe signal. 1 =WR functions as a write strobe signal - - Reserved Channel Select These three bits select which T1 channel within the XRT86VX38 uses the Transmit DMA_0 (Write) interface. 000 = Channel 0 001 = Reserved 001 = Channel 2 011 = Reserved 1xx = Reserved 4 - 3 Reserved 2 DMA0_CHAN(2) R/W 0 1 DMA0_CHAN(1) R/W 0 0 DMA0_CHAN(0) R/W 0 36 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 22: DMA 1 (READ) CONFIGURATION REGISTER (D1RCR) BIT FUNCTION 7-6 Reserved TYPE DEFAULT - - Reserved REV. 1.0.1 HEX ADDRESS: 0XN119 DESCRIPTION-OPERATION 7 DMA1 RST R/W 0 DMA_1 Reset This bit resets the Receive DMA (Read) Channel 1 0 = Normal operation. 1 = A zero to one transition resets the Receive DMA (Read) channel 1. 6 DMA1 ENB R/W 0 DMA1_ENB This bit enables the Receive DMA_1 (Read) interface. After a receive DMA is enabled, DMA transfers are only requested when the receive cell buffer contains a complete message or cell. The DMA read channel is used by the T1 Framer to transfer data from the HDLC buffers within the T1 Framer to external memory. The DMA Read cycle starts by T1 Framer asserting the DMA Request (REQ1) ‘low’, then the external DMA controller should drive the DMA Acknowledge (ACK1) ‘low’ to indicate that it is ready to receive the data. The T1 Framer should place new data on the Microprocessor data bus each time the Read Signal is Strobed low if the RD is configured as a Read Strobe. If RD is configured as a direction signal, then the T1 Framer would place new data on the Microprocessor data bus each time the Write Signal (WR) is Strobed low. 0 = Disables the DMA_1 (Read) interface 1 = Enables the DMA_1 (Read) interface 5 RD TYPE R/W 0 READ Type Select This bit selects the function of the RD signal. 0 = RD functions as a Read Strobe signal 1 = RD acts as a direction signal (indicates whether the current bus cycle is a read or write operation), and WR works as a data strobe. - - Reserved Channel Select These three bits select which T1 channel within the chip uses the Receive DMA_1 (Read) interface. 000 = Channel 0 001 = Reserved 001 = Channel 2 011 = Reserved 1xx = Reserved 4 - 3 Reserved 2 DMA1_CHAN(2) R/W 0 1 DMA1_CHAN(1) R/W 0 0 DMA1_CHAN(0) R/W 0 37 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 23: INTERRUPT CONTROL REGISTER (ICR) BIT FUNCTION 7-3 Reserved HEX ADDRESS: 0XN11A TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved 2 INT_WC_RUR R/W 0 Interrupt Write-to-Clear or Reset-upon-Read Select This bit configures all Interrupt Status bits to be either Reset Upon Read or Write-to-Clear 0= Configures all Interrupt Status bits to be Reset-Upon-Read (RUR). 1= Configures all Interrupt Status bits to be Write-to-Clear (WC). 1 ENBCLR R/W 0 Interrupt Enable Auto Clear This bit configures all interrupt enable bits to clear or not clear after reading the interrupt status bit. 0= Configures all Interrupt Enable bits to not cleared after reading the interrupt status bit. The corresponding Interrupt Enable bit will stay ‘high’ after reading the interrupt status bit. 1= Configures all interrupt Enable bits to clear after reading the interrupt status bit. The corresponding interrupt enable bit will be set to ‘low’ after reading the interrupt status bit. 0 INTRUP_ENB R/W 0 Interrupt Enable for Framer_n This bit enables or disables the entire T1 Framer Block for Interrupt Generation. 0 = Disables the T1 framer block for Interrupt Generation 1 = Enables the T1 framer block for Interrupt Generation 38 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 24: LAPD SELECT REGISTER (LAPDSR) BIT FUNCTION [7:5] Reserved REV. 1.0.1 HEX ADDRESS: 0XN11B TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved 4 HDLC3en R/W 1 HDLC Controller 3 Enable This bit is used to enable or disable HDLC Controller 3. By default, the HDLC controller is Enabled, this bit set to "1". If the HDLC controller is disabled while transmitting a message, BOS will disrupt the transmission and send all ones, MOS will send the flag sequence. 0 - Disabled 1 - Enabled 3 HDLC2en R/W 1 HDLC Controller 2 Enable This bit is used to enable or disable HDLC Controller 2. By default, the HDLC controller is Enabled, this bit set to "1". If the HDLC controller is disabled while transmitting a message, BOS will disrupt the transmission and send all ones, MOS will send the flag sequence. 0 - Disabled 1 - Enabled 2 HDLC1en R/W 1 HDLC Controller 1 Enable This bit is used to enable or disable HDLC Controller 1. By default, the HDLC controller is Enabled, this bit set to "1". If the HDLC controller is disabled while transmitting a message, BOS will disrupt the transmission and send all ones, MOS will send the flag sequence. 0 - Disabled 1 - Enabled [1:0] HDLC Controller Select[1:0] R/W 0 HDLC Controller Select[1:0]: These bits permit the user to select any of the three (3) HDLC Controllers that he/she will use within this particular channel, as depicted below. 00 & 11 - Selects HDLC Controller # 1 01 - Selects HDLC Controller # 2 10 - Selects HDLC Controller # 3 39 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 25: CUSTOMER INSTALLATION ALARM GENERATION REGISTER (CIAGR) BIT FUNCTION HEX ADDRESS: 0XN11C TYPE DEFAULT - - [3:2] CIAG R/W 00 CI Alarm Transmit (Only in ESF) These two bits are used to enable or disable AIS-CI or RAI-CI generation in T1 ESF mode only. Alarm Indication Signal-Customer Installation (AIS-CI) and Remote Alarm Indication-Customer Installation (RAI-CI) are intended for use in a network to differentiate between an issue within the network or the Customer Installation (CI). AIS-CI AIS-CI is an all ones signal with an embedded signature of 01111100 11111111 (right-to left) which recurs at 386 bit intervals inthe DS-1 signal. RAI-CI Remote Alarm Indication - Customer Installation (RAI-CI) is a repetitive pattern with a period of 1.08 seconds. It comprises 0.99 seconds of RAI message (00000000 11111111 Right-to-left) and a 90 ms of RAI-CI signature (00111110 11111111 Right to left) to form a RAI-CI signal. RAI-CI applies to T1 ESF framing mode only. 00/11 = Disables RAI-CI or AIS-CI alarms generation 01 = Enables unframed AIS-CI alarm generation 10 = Enables RAI-CI alarm generation [1:0] CIAD R/W 00 CI Alarm Detect (Only in ESF) These two bits are used to enable or disable RAI-CI or AIS-CI alarm detection in T1 ESF mode only. 00/11 = Disables the RAI-CI or AIS-CI alarm detection 01 = Enables the unframed AIS-CI alarm detection 10 = Enables the RAI-CI alarm detection [7:4] Reserved DESCRIPTION-OPERATION Reserved 40 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 26: PERFORMANCE REPORT CONTROL REGISTER (PRCR) BIT 7 FUNCTION LBO_ADJ_ENB REV. 1.0.1 HEX ADDRESS: 0XN11D TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit Line Build Out Auto Adjustment: This bit is used to enable or disable the transmit line build out auto adjustment feature. When the transmitter of the device is sending AIS condition, the transmit line build out will automatically be adjust to one setting lower if this feature is enabled. (Please refer to the EQC[4:0] bits in register 0xNF00 for different settings of Transmit Line Build Out). This feature is designed to for power saving purposes when an AIS signal is being transmitted. 1 - Enables the transmit line build out auto adjustment feature. 0 - Disables the transmit line build out auto adjustment feature. NOTE: This feature is only available for T1 short haul applications. 6 RLOS_OUT_ENB [5-3] Reserved 2 C/R_BIt [1:0] APCR R/W 1 RLOS Output Enable: This bit is used to enable or disable the Receive LOS (RLOS_n) output pins. When this bit is set "Low", the RLOS_n pin will be tri-stated for all conditions. When this bit is set "High", the RLOS_n pin will pull "High" during a LOS condition and pull "Low" when data is present on RTIP/RRING. 0 - Disables the RLOS output pin. 1 - Enables the RLOS output pin. - - Reserved. R/W 0 C/R Bit Control This bit allows user to control the value of C/R bit within an outgoing performance report. 0 - Outgoing C/R bit will be set to’0’ 1 - Outgoing C/R bit will be set to’1’ R/W 00 Automatic Performance Control/Response Report These bits automatically generates a summary report of the PMON status so that it can be inserted into an out going LAPD message. Automatic performance report can be generated every time these bits transition from ‘b00’ to ‘b01‘or automatically every one second. The table below describes the different APCR[1:0] bits settings. APCR[1:0] 00/11 SOURCE FOR RECEIVE D/E TIMESLOTS No performance report issued 01 Single performance report is issued when these bits transitions from ‘b00’ to b’01’. 10 Automatically issues a performance report every one second 41 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 27: GAPPED CLOCK CONTROL REGISTER (GCCR) BIT 7 FUNCTION FrOutclk [6:2] Reserved HEX ADDRESS: 0XN11E TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Framer Output Clock Reference This bit is used to enable or disable high-speed T1 rate on the T1OSCCLK and the E1OSCCLK output pins. By default, the output clock reference on T1OSCCLK and E1OSCCLK output pins are set to 1.544MHz/2.048MHz respectively. By setting this bit to a “1”, the output clock reference on the T1OSCLK and the E1OSCCLK are changed to 49.408MHz/ 65.536MHz respectively. 0 = Disables high-speed rate to be output on the T1OSCCLK and E1OSCCLK output pins. 1 = Enables high-speed rate to be output on the T1OSCCLK and E1OSCCLK output pins. - - Reserved 1 TxGCCR R/W 0 Transmit Gapped Clock Interface This bit is used to enable or disable the transmit gapped clock interface operating at 2.048Mbit/s in DS-1 mode. In this application, 63 gaps (missing data) are inserted so that the overall bit rate is reduced to 1.544Mbit/s. If the transmit Gapped Clock Interface is enabled: TxMSYNC is used as the 2.048MHz Gapped Clock Input. TxSER is used as the 2.048MHz Gapped Data Input. TxSERCLK must be a 1.544MHz clock input. 0 = Disables the transmit gapped clock interface. 1 = Enables the transmit gapped clock interface. 0 RxGCCR R/W 0 Receive Gapped Clock Interface This bit is used to enable or disable the receive gapped clock interface operating at 2.048Mbit/s in DS-1 mode. In this application, 63 gaps (missing data) are extracted so that the overall bit rate is reduced to 1.544Mbit/s. If the Receive Gapped Clock Interface is enabled: RxSERCLK should be configured as a Gapped clock input at 2.048MHz so that a 2.048MHz Gapped Clock can be applied to the Framer block. RxSER is used as the 2.048MHz Gapped Data Output. The position of the gaps will be determined by the gaps placed on RxSERCLK by the user. 0 = Disables the Receive Gapped Clock Interface 1 = Enables the Receive Gapped Clock Interface 42 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 28: TRANSMIT INTERFACE CONTROL REGISTER (TICR) BIT 7 FUNCTION TxSyncFrD REV. 1.0.1 HEX ADDRESS:0XN120 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Tx Synchronous fraction data interface This bit selects whether TxCHCLK or TxSERCLK will be used for fractional data input if fractional interface is enabled. If TxSERCLK is selected to clock in fractional data input, TxCHCLK will be used as an enable signal 0 = Fractional data Is clocked into the chip using TxChCLK if fractional data interface is enabled. 1 = Fractional data is clocked into the chip using TxSerClk. TxChClk is used as fractional data enable. NOTE: The Time Slot Identifier Pins (TxChn[4:0]) still indicates the time slot number if fractional data interface is not enabled. Fractional Interface can be enabled by setting TxFr1544 to 1 6 Reserved 5 TxPLClkEnb/ TxSync Is Low - - Reserved R/W 0 Transmit payload clock enable/TxSYNC is Active Low This exact function of this bit depends on whether the T1 framer is configured to operate in base rate or high speed modes of operation. If the T1 framer is configured to operate in base rate - TxPayload Clock: This bit configures the framer to output a regular clock or a payload clock on the transmit serial clock (TxSERCLK) pin when TxSERCLK is configured to be an output. 0 = Configures the framer to output a 1.544MHz clock on the TxSERCLK pin when TxSERCLK is configured as an output. 1 = Configures the framer to output a 1.544MHz clock on the TxSERCLK pin when transmitting payload bits. There will be gaps on the TxSERCLK output pin when transmitting overhead bits. If the T1 framer is configured to operate in high-speed or multiplexed modes - TxSYNC is Active Low: This bit is used to select whether the transmit frame boundary (TxSYNC) is active low or active high. 0 = Selects TxSync to be active “High” 1 = Selects TxSync to be active “Low” 43 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 28: TRANSMIT INTERFACE CONTROL REGISTER (TICR) BIT 4 FUNCTION TxFr1544 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Fractional/Signaling Interface Enabled This bit is used to enable or disable the transmit fractional data interface, signaling input, as well as the 32MHz transmit clock and the transmit overhead Signal output. 0 = Configures the 5 time slot identifier pins (TxChn[4:0]) to output the channel number as usual. 1 = Configures the 5 time slot identifier pins (TxChn[4:0]) to function as the following: TxChn[0] becomes the Transmit Serial SIgnaling pin (TxSIG_n) for signaling inputs. Signaling data can now be input from the TxSIG pin if configured appropriately. TxChn[1] becomes the Transmit Fractional Data Input pin (TxFrTD_n) for fractional data input. Fractional data can now be input from the TxFrTD pin if configured appropriately. TxChn[2] becomes the 32 MHz transmit clock output TxChn[3] becomes the Transmit Overhead Signal which pulses high on the first bit of each multi-frame. NOTE: 3 TxICLKINV HEX ADDRESS:0XN120 R/W 0 This bit has no effect in the high speed or multiplexed modes of operation. In high-speed or multiplexed modes, TxCHN[0] functions as TxSIGn for signaling input. Transmit Clock Inversion (Backplane Interface) This bit selects whether data transition will happen on the rising or falling edge of the transmit clock. 0 = Selects data transition to happen on the rising edge of the transmit clocks. 1 = Selects data transition to happen on the falling edge of the transmit clocks. NOTE: This feature is only available for base rate configuration (i.e. nonhighspeed, and non-multiplexed modes). 2 TxMUXEN R/W 0 Multiplexed Mode Enable This bit enables or disables the multiplexed mode. When multiplexed mode is enable, multiplexed data of four channels at 12.352 or 16.384MHz are demultiplexed inside the transmit framer and sent to 2 channels on the line side. The backplane speed will be running at either 12.352 or 16.384MHz depending on the multiplexed mode selected by TxIMODE[1:0] of this register. 0 = Disables the multiplexed mode. 1 = Enables the multiplexed mode. 44 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 28: TRANSMIT INTERFACE CONTROL REGISTER (TICR) BIT FUNCTION 1-0 TxIMODE[1:0] REV. 1.0.1 HEX ADDRESS:0XN120 TYPE DEFAULT DESCRIPTION-OPERATION R/W 00 Transmit Interface Mode selection This bit determines the transmit interface speed. The exact function of these two bits depends on whether Multiplexed mode is enabled or disabled. Table 29 and Table 30 shows the functions of these two bits for non-multiplexed and multiplexed modes.: TABLE 29: TRANSMIT INTERFACE SPEED WHEN MULTIPLEXED MODE IS DISABLED (TXMUXEN = 0) TXIMODE[1:0] TRANSMIT INTERFACE SPEED 00 1.544Mbit/s Base Rate Mode: Transmit Backplane interface signals include: TxSERCLK is an input or output clock at 1.544MHz TxMSYNC is the superframe boundary at 3ms (ESF) or 1.5ms (SF) TxSYNC is the single frame boundary at 125 us TxSER is the base-rate data input 01 2.048Mbit/s (High-Speed MVIP Mode): Transmit backplane interface signals include: TxSERCLK is an input clock at 1.544MHz TxMSYNC is the high speed input clock at 2.048MHz to input high-speed data TxSYNC can be configured as a single frame or superframe boundary, depending on the setting of bit 5 of register 0xN109 TxSER is the high-speed data input 10 4.096Mbit/s High-Speed Mode: Transmit Backplane interface signals include: TxSERCLK is an input clock at 1.544MHz TxMSYNC will become the high speed input clock at 4.096MHz to input high-speed data TxSYNC can be configured as a single frame or superframe boundary, depending on the setting of bit 5 of register 0xN109 TxSER is the high-speed data input 11 8.192Mbit/s High-Speed Mode: Transmit Backplane interface signals include: TxSERCLK is an input clock at 1.544MHz TxMSYNC will become the high speed input clock at 8.192MHz to input high-speed data TxSYNC can be configured as a single frame or superframe boundary, depending on the setting of bit 5 of register 0xN109 TxSER is the high-speed data input 45 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 28: TRANSMIT INTERFACE CONTROL REGISTER (TICR) BIT FUNCTION 1-0 TxIMODE[1:0] TYPE DEFAULT R/W 00 HEX ADDRESS:0XN120 DESCRIPTION-OPERATION (Continued) TABLE 30: TRANSMIT INTERFACE SPEED WHEN MULTIPLEXED MODE IS ENABLED (TXMUXEN = 1) TXIMODE[1:0] TRANSMIT INTERFACE SPEED 00 Bit-Multiplexed Mode at 12.352MHz is Enabled: Transmit backplane interface is taking four-channel multiplexed data at a rate of 12.352Mbit/s from channel 0 and bit-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. The TxSYNC signal pulses “High” during the framing bit of each DS-1 frame. 01 Bit-Multiplexed Mode at 16.384MHz is Enabled: Transmit backplane interface is taking four-channel multiplexed data at a rate of 16.384Mbit/s from channel 0 and bit-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. The TxSYNC signal pulses “High” during the framing bit of each DS-1 frame. 10 HMVIP High-Speed Multiplexed Mode Enabled: Transmit backplane interface is taking four-channel multiplexed data at a rate of 16.384Mbit/s from channel 0 and byte-demultiplexing the serial data into 4 channels and output on channels 0 through 3. The TxSYNC signal pulses “High” during the last two bits of the previous DS1 frame and the first two bits of the current DS-1 frame. 11 H.100 High-Speed Multiplexed Mode Enabled: Transmit backplane interface is taking four-channel multiplexed data at a rate of 16.384Mbit/s from channel 0 and byte-demultiplexing the serial data into 4 channels and output to the line on channels 0 through 3. The TxSYNC signal pulses “High” during the last bit of the previous DS-1 frame and the first bit of the current DS-1 frame. Transmit backplane interface signals include: TxSERCLK is an input clock at 1.544MHz TxMSYNC will become the highspeed input clock at 12.352 or 16.384MHz to input high-speed multiplexed data on the back-plane interface TxSYNC can be configured as a single frame or super-frame boundary, depending on the setting of bit 5 of register 0xN109 TxSER is the high-speed data input NOTE: In high speed mode, transmit data is sampled on the rising edge of the 12Mhz or 16MHz clock edge. 46 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 31: BERT CONTROL & STATUS REGISTER (BERTCSR0) BIT FUNCTION 7-4 Reserved REV. 1.0.1 HEX ADDRESS: 0XN121 TYPE DEFAULT DESCRIPTION-OPERATION - - These bits are not used 3 BERT_Switch R/W 0 BERT Switch This bit enables or disables the BERT switch function within the XRT86VX38 device. By enabling the BERT switch function, BERT functionality will be switched between the receive and transmit framer. T1 Receive framer will generate the BERT pattern and insert it onto the receive backplane interface, and T1 Transmit Framer will be monitoring the transmit backplane interface for BERT pattern and declare BERT LOCK if BERT has locked onto the input pattern. If BERT switch is disabled, T1 Transmit framer will generate the BERT pattern to the line interface and the receive framer will be monitoring the line for BERT pattern and declare BERT LOCK if BERT has locked onto the input pattern. 0 = Disables the BERT Switch Feature. 1 = Enables the BERT Switch Feature. 2 BER[1] R/W 0 1 BER[0] R/W 0 Bit Error Rate This bit is used to insert BERT bit error at the rates presented at the table below. The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 within this register). If the BERT switch function is disabled, bit error will be inserted by the T1 transmit framer out to the line interface if this bit is enabled. If the BERT switch function is enabled, bit error will be inserted by the T1 receive framer out to the receive backplane interface if this bit is enabled. BER[1:0] BIT ERROR RATE 00/11 Disable Bit Error insertion to the transmit output or receive backplane interface 01 Bit Error is inserted to the transmit output or receive backplane interface at a rate of 1/1000 (one out of one Thousand) 10 Bit Error is inserted to the transmit output or receive backplane interface at a rate of 1/ 1,000,000 (one out of one million) 47 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 31: BERT CONTROL & STATUS REGISTER (BERTCSR0) BIT 0 HEX ADDRESS: 0XN121 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION UnFramedBERT R/W 0 Unframed BERT Pattern This bit enables or disables unframed BERT pattern generation (i.e. All timeslots and framing bits are all BERT data). The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 within this register). If BERT switch function is disabled, T1 Transmit Framer will generate an unframed BERT pattern to the line side if this bit is enabled. If PRBS switch function is enabled, T1 Receive Framer will generate an unframed BERT pattern to the receive backplane interface if this bit is enabled. 0 - Enables an unframed BERT pattern generation to the line interface or to the receive backplane interface 1 - Disables an unframed BERT pattern generation to the line interface or to the receive backplane interface 48 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 32: RECEIVE INTERFACE CONTROL REGISTER (RICR) BIT 7 REV. 1.0.1 HEX ADDRESS: 0XN122 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION RxSyncFrD R/W 0 Receive Synchronous fraction data interface This bit selects whether RxCHCLK or RxSERCLK will be used for fractional data output if receive fractional interface is enabled. If RxSERCLK is selected to clock out fractional data, RxCHCLK will be used as an enable signal 0 = Fractional data Is clocked out of the chip using RxChCLK if the receive fractional interface is enabled. 1 = Fractional data is clocked out of the chip using RxSerClk if the receive fractional interface is enabled. RxChClk is used as fractional data enable. NOTE: The Time Slot Identifier Pins (RxChn[4:0]) still indicates the time slot number if the receive fractional data interface is not enabled. Fractional Interface can be enabled by setting RxFr1544 to 1 6 Reserved 5 RxPLClkEnb/ RxSync is low - - Reserved R/W 0 Receive payload clock enable/RxSYNC is Active Low This exact function of this bit depends on whether the T1 framer is configured to operate in base rate or high speed modes of operation. If the T1 framer is configured to operate in base rate - TxPayload Clock: This bit configures the T1 framer to either output a regular clock or a payload clock on the receive serial clock (RxSERCLK) pin when RxSERCLK is configured to be an output. 0 = Configures the framer to output a 1.544MHz clock on the RxSERCLK pin when RxSERCLK is configured as an output. 1 = Configures the framer to output a 1.544MHz clock on the RxSERCLK pin when receiving payload bits. There will be gaps on the RxSERCLK output pin when receiving overhead bits. If the T1 framer is configured to operate in high-speed or multiplexed modes - RxSYNC is Active Low: This bit is used to select whether the receive frame boundary (RxSYNC) is active low or active high. 0 = Selects RxSync to be active “High” 1 = Selects RxSync to be active “Low” 49 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 32: RECEIVE INTERFACE CONTROL REGISTER (RICR) BIT 4 FUNCTION RxFr1544 HEX ADDRESS: 0XN122 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Receive Fractional/Signaling Interface Enabled This bit is used to enable or disable the receive fractional output interface, receive signaling output, the serial channel number output, as well as the 8kHz and the received recovered clock output. This bit only functions when the device is configured in non-high speed or multiplexed modes of operations. If the device is configured in base rate: 0 = Configures the 5 time slot identifier pins (RxChn[4:0]) to output the channel number in parallel as usual. 1 = Configures the 5 time slot identifier pins (RxChn[4:0]) into the following different functions: RxChn[0] becomes the Receive Serial SIgnaling output pin (RxSIG_n) for signaling outputs. Signaling data can now be output to the RxSIG pin if configured appropriately. RxChn[1] becomes the Receive Fractional Data Output pin (RxFrTD_n) for fractional data output. Fractional data can now be output to the RxFrTD pin if configured appropriately. RxChn[2] outputs the serial channel number RxChn[3] outputs an 8kHz clock signal. RxCHN[4] outputs the received recovered clock signal (1.544MHz for T1) NOTE: This bit has no effect in the high speed or multiplexed modes of operation. In high-speed or multiplexed modes, RxCHN[0] outputs the Signaling data and RxCHN[4] outputs the recovered clock. 3 RxICLKINV N/A 0 Receive Clock Inversion (Backplane Interface) This bit selects whether data transition will happen on the rising or falling edge of the receive clock. 0 = Selects data transition to happen on the rising edge of the receive clocks. 1 = Selects data transition to happen on the falling edge of the receive clocks. NOTE: This feature is only available for base rate configuration (i.e. nonhighspeed, or non-multiplexed modes). 2 RxMUXEN R/W 0 Receive Multiplexed Mode Enable This bit enables or disables the multiplexed mode on the receive side. When multiplexed mode is enable, data of four channels from the line side are multiplexed onto one serial stream inside the receive framer and output to the back-plane interface on RxSER. The backplane speed will become either 12.352MHz or 16.384MHz once multiplexed mode is enabled. 0 = Disables the multiplexed mode. 1 = Enables the multiplexed mode. 50 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 32: RECEIVE INTERFACE CONTROL REGISTER (RICR) BIT FUNCTION 1-0 RxIMODE[1:0] REV. 1.0.1 HEX ADDRESS: 0XN122 TYPE DEFAULT DESCRIPTION-OPERATION R/W 00 Receive Interface Mode Selection[1:0] This bit determines the receive backplane interface speed. The exact function of these two bits depends on whether Receive Multiplexed mode is enabled or disabled. Table 33 and Table 34 shows the functions of these two bits for non-multiplexed and multiplexed modes.: TABLE 33: RECEIVE INTERFACE SPEED WHEN MULTIPLEXED MODE IS DISABLED (TXMUXEN = 0) RXIMODE[1:0] RECEIVE INTERFACE SPEED 00 1.544Mbit/s Base Rate Mode Receive backplane interface signals include: RxSERCLK is an input or output clock at 1.544MHz RxSYNC is an input or output signal which indicates the receive singe frame boundary RxSER is the base-rate data output 01 2.048Mbit/s High-Speed MVIP Mode: Receive backplane interface signals include: RxSERCLK is an input clock at 2.048MHz RxSYNC is an input signal which indicates the receive singe frame boundary RxSER is the high-speed data output 10 4.096Mbit/s High-Speed Mode: Receive backplane interface signals include: RxSERCLK is an input clock at 4.096MHz RxSYNC is an input signal which indicates the receive singe frame boundary RxSER is the high-speed data output 11 8.192Mbit/s High-Speed Mode: Receive backplane interface signals include: RxSERCLK is an input clock at 8.192MHz RxSYNC is an input signal which indicates the receive singe frame boundary RxSER is the high-speed data output 51 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 32: RECEIVE INTERFACE CONTROL REGISTER (RICR) BIT FUNCTION 1-0 RxIMODE[1:0] TYPE DEFAULT R/W 00 HEX ADDRESS: 0XN122 DESCRIPTION-OPERATION (Continued):( TABLE 34: RECEIVE INTERFACE SPEED WHEN MULTIPLEXED MODE IS ENABLED (TXMUXEN = 1) TXIMODE[1:0] TRANSMIT INTERFACE SPEED 00 Bit-Multiplexed Mode at 12.352MHz is Enabled: Receive backplane interface is taking data from the four LIU input channels 0 through 3 and bit-multiplexing the four-channel data into one 12.352MHz serial stream and output on channel 0 of the Receive Serial Output (RxSER). The RxSYNC signal pulses “High” during the framing bit of each DS-1 frame. 01 Bit-Multiplexed Mode at 16.384MHz is Enabled: Receive backplane interface is taking data from the four LIU input channels 0 through 3 and bit-multiplexing the four-channel data into one 16.384MHz serial stream and output to channel 0 of the Receive Serial Output (RxSER). The RxSYNC signal pulses “High” during the framing bit of each T1 frame. 10 HMVIP High-Speed Multiplexed Mode Enabled: Receive backplane interface is taking data from the four LIU input channels 0 through 3 and byte-multiplexing the four-channel data into one 16.384MHz serial stream and output to channel 0 of the Receive Serial Output (RxSER). The RxSYNC signal pulses “High” during the last two bits of the previous T1 frame and the first two bits of the current T1 frame. 11 H.100 High-Speed Multiplexed Mode Enabled: Receive backplane interface is taking data from the four LIU input channels 0 through 3 and byte-multiplexing the four-channel data into one 16.384MHz serial stream and output to channel 0 of the Receive Serial Output (RxSER). The RxSYNC signal pulses “High” during the last bit of the previous T1 frame and the first bit of the current T1 frame. Receive backplane interface signals include: RxSERCLK is an input clock at either 12.352MHz or16.384MHz depending on the selected multiplexed mode. RxSYNC is an input signal which indicates the multiplexed frame boundary. The length of RxSYNC depends on the multiplexed mode selected. RxSER is the high-speed data output NOTE: In high speed mode, receive data is clocked out on the rising edge of the 12Mhz or 16MHz clock edge. 52 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 35: BERT CONTROL & STATUS REGISTER (BERTCSR1) BIT 7 FUNCTION PRBSTyp REV. 1.0.1 HEX ADDRESS: 0XN123 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 PRBS Pattern Type This bit selects the type of PRBS pattern that the T1 Transmit/ Receive framer will generate or detect. PRBS 15 (X15 + X14 +1) Polynomial or QRTS (Quasi-Random Test Signal) Pattern can be generated by the transmit or receive framer depending on whether PRBS switch function is enabled or not (bit 3 in register 0xN121). If the PRBS Switch function is disabled, T1 transmit framer will generate either PRBS 15 or QRTS pattern and output to the line interface. PRBS 15 or QRTS pattern depends on the setting of this bit. If the PRBS Switch function is enabled, T1 receive framer will generate either PRBS 15 or QRTS pattern and output to the receive back plane interface. PRBS 15 or QRTS pattern depends on the setting of this bit. 0 = Enables the PRBS 15 (X15 + X14 +1) Polynomial generation. 1 = Enables the QRTS (Quasi-Random Test Signal) pattern generation. 6 ERRORIns R/W 0 Error Insertion This bit is used to insert a single BERT error to the transmit or receive output depending on whether BERT switch function is enabled or not. (bit 3 in register 0xN121). If the BERT Switch function is disabled, T1 transmit framer will insert a single BERT error and output to the line interface if this bit is enabled. If the BERT Switch function is enabled, T1 receive framer will insert a single BERT error and output to the receive back plane interface if this bit is enabled. A ‘0’ to ‘1’ transition will cause one output bit inverted in the BERT stream. NOTE: This bit only works if BERT generation is enabled. 5 DATAInv R/W 0 BERT Data Invert: This bit inverts the Transmit BERT output data and the Receive BERT input data. The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 in register 0xN121). If the BERT Switch function is disabled and if this bit is enabled, T1 transmit framer will invert the BERT data before it outputs to the line interface, and the T1 receive framer will invert the incoming BERT data before it receives it. If the BERT Switch function and this bit are both enabled, T1 receive framer will invert the BERT data before it outputs to the line interface, and the T1 transmit framer will invert the incoming BERT data before it receives it. 0 - Transmit and Receive Framer will NOT invert the Transmit and Receive BERT data. 1 - Transmit and Receive Framer will invert the Transmit and Receive BERT data. 53 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 35: BERT CONTROL & STATUS REGISTER (BERTCSR1) BIT FUNCTION HEX ADDRESS: 0XN123 TYPE DEFAULT DESCRIPTION-OPERATION 4 RxBERTLock RO 0 Lock Status This bit indicates whether or not the Receive or Transmit BERT lock has obtained. The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 in register 0xN121). If the BERT Switch function is disabled, T1 receive framer will declare LOCK if BERT has locked onto the input pattern. If the BERT Switch function is disabled, T1 transmit framer will declare LOCK if BERT has locked onto the input pattern. 0 = Indicates the Receive BERT has not Locked onto the input patterns. 1 = Indicates the Receive BERT has locked onto the input patterns. 3 RxBERTEnb R/W 0 Receive BERT Detection/Generation Enable This bit enables or disables the receive BERT pattern detection or generation. The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 in register 0xN121). If the BERT switch function is disabled and if this bit is enabled, T1 Receive Framer will detect the incoming BERT pattern from the line side and declare BERT lock if incoming data locks onto the BERT pattern. If the BERT switch function and this bit are both enabled, T1 Transmit Framer will detect the incoming BERT pattern from the transmit backplane interface and declare BERT lock if incoming data locks onto the BERT pattern. 0 = Disables the Receive BERT pattern detection. 1 = Enables the Receive BERT pattern detection. 2 TxBERTEnb R/W 0 Transmit BERT Generation Enable This bit enables or disables the Transmit BERT pattern generator. The exact function of this bit depends on whether BERT switch function is enabled or not. (bit 3 in register 0xN121). If BERT switch function is disabled, T1 Transmit Framer will generate the BERT pattern to the line side if this bit is enabled. If BERT switch function is enabled, T1 Receive Framer will generate the BERT pattern to the receive backplane interface if this bit is enabled. 0 = Disables the Transmit BERT pattern generator. 1 = Enables the Transmit BERT pattern generator. 1 RxBypass R/W 0 Receive Framer Bypass This bit enables or disables the Receive T1 Framer bypass. 0 = Disables the Receive T1 framer Bypass. 1 = Enables the Receive T1 Framer Bypass. 0 TxBypass R/W 0 Transmit Framer Bypass This bit enables or disables the Transmit T1 Framer bypass. 0 = Disables the Transmit T1 framer Bypass. 1 = Enables the Transmit T1 Framer Bypass. 54 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 36: LOOPBACK CODE CONTROL REGISTER - CODE 0 (LCCR0) BIT FUNCTION 7-6 RXLBCALEN[1:0] HEX ADDRESS: 0XN124 TYPE DEFAULT DESCRIPTION-OPERATION R/W 00 Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported by the XRT86VX38 as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] REV. 1.0.1 R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported by the XRT86VX38 as presented in the table below RXLBCDLEN[1:0] 55 RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 36: LOOPBACK CODE CONTROL REGISTER - CODE 0 (LCCR0) BIT FUNCTION 3-2 TXLBCLEN[1:0] TYPE DEFAULT R/W 00 HEX ADDRESS: 0XN124 DESCRIPTION-OPERATION Transmit Loopback Code Length This bit determines transmit loopback code length. There are four lengths supported by the XRT86VX38 as presented in the table below TXLBCLEN[1:0] TRANSMIT LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit transmit loopback code Sequence 01 Selects 5-bit transmit loopback code Sequence 10 Selects 6-bit transmit loopback code Sequence 11 Selects 7-bit transmit loopback code Sequence 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 AUTOENB R/W 0 Remote Loopback Automatically This bit configures the XRT86VX38 in remote loopback automatically upon detecting the loopback code activation code specified in the Receive Loopback Code Activation Register if Receive activation loopback code is enabled (Register address:0xN126). The XRT86VX38 will cancel the remote loopback upon detecting the loopback code deactivation code specified in the Receive Loopback Code Deactivation register if the Receive deactivation loopback code is enabled. (Register address:0xN127) 0 = Disables automatic remote loopback upon detecting the receive activation code. 1 = Enables automatic remote loopback upon detecting the receive activation code. NOTE: This feature is only available on the Loopcode 0 Controller. Loopcode Generators 1 through 7 do not support this feature. 56 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 37: TRANSMIT LOOPBACK CODER REGISTER (TLCR) BIT FUNCTION 7-1 TXLBC[6:0] 0 TXLBCENB HEX ADDRESS: 0XN125 TYPE DEFAULT R/W 1010101 Transmit Loopback Code These seven bits determine the transmit loopback code. The MSB of the transmit loopback code is loaded first for transmission. R/W 0 DESCRIPTION-OPERATION Transmit Loopback Code Enable This bit enables loopback code generation in the transmit path. Transmit loopback code is generated by writing the transmit loopback code in this register and enabling it using this bit. The length and the format of the transmit loopback code is determined by the Loopback Code Control Register. 0 = Disables the transmit loopback code generation. 1 = Enables the transmit loopback code generation. TABLE 38: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 0 (RLACR0) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN126 TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 39: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 0 (RLDCR0) BIT REV. 1.0.1 HEX ADDRESS: 0XN127 TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 57 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 40: RECEIVE LOOPCODE DETECTION SWITCH (RLCDS) BIT HEX ADDRESS: 0XN128 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 RxLCDetSwitch7 R/W 7 Receive LoopCode Switch 7 If receive loopcode 7 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 6 RxLCDetSwitch6 R/W 6 Receive LoopCode Switch 6 If receive loopcode 6 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 5 RxLCDetSwitch5 R/W 5 Receive LoopCode Switch 5 If receive loopcode 5 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 4 RxLCDetSwitch4 R/W 4 Receive LoopCode Switch 4 If receive loopcode 4 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 3 RxLCDetSwitch3 R/W 3 Receive LoopCode Switch 3 If receive loopcode 3 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 2 RxLCDetSwitch2 R/W 2 Receive LoopCode Switch 2 If receive loopcode 2 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 58 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 40: RECEIVE LOOPCODE DETECTION SWITCH (RLCDS) BIT REV. 1.0.1 HEX ADDRESS: 0XN128 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 RxLCDetSwitch1 R/W 0 Receive LoopCode Switch 1 If receive loopcode 1 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) 0 RxLCDetSwitch0 R/W 0 Receive LoopCode Switch 0 If receive loopcode 0 is enabled, this bit will determine which input the loopcode will be detected on. By default, the loopcode is searching for the line side (RTIP/RRING). 0 - Line Side (RTIP/RRING) 1 - System Side (TxSER) TABLE 41: DEFECT DETECTION ENABLE REGISTER (DDER) BIT 7 FUNCTION DEFDET HEX ADDRESS: 0XN129 TYPE DEFAULT DESCRIPTION-OPERATION R/W 1 For defect detection per ANSI T1.231-1997 and T1.403-1999, user should leave this bit set to ‘1’. 59 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 42: LOOPBACK CODE CONTROL REGISTER - CODE 1 (LCCR1) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN12A RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 60 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 43: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 1 (RLACR1) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN12B TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 44: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 1 (RLDCR1) BIT REV. 1.0.1 HEX ADDRESS: 0XN12C TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 61 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 45: LOOPBACK CODE CONTROL REGISTER - CODE 2 (LCCR2) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN12D RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 62 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 46: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 2 (RLACR2) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN12E TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 47: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 2 (RLDCR2) BIT REV. 1.0.1 HEX ADDRESS: 0XN12F TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 63 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 48: TRANSMIT LOOPCODE GENERATION SWITCH (TLCGS) BIT FUNCTION 7-1 Reserved 0 TxLCGenSwitch HEX ADDRESS: 0XN140 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Reserved R/W 0 Transmit LoopCode Switch If the transmit loopcode is enabled, this bit will determine which direction the loopcode will be transmitted. By default, the loopcode is generated on the line side (TTIP/TRING). 0 - Line Side (TTIP/TRING) 1 - System Side (RxSER) TABLE 49: LOOPCODE TIMER SELECT (LCTS) BIT FUNCTION TYPE DEFAULT 7-3 Reserved R/W 0 2-0 LCTimer R/W 110 HEX ADDRESS: 0XN141 DESCRIPTION-OPERATION Reserved Loopcode Timer Select These bits are used to select the timer value for declaring a valid loopcode detection for both Activation and De-Activation. By default, the timer is set to 5 seconds. 000 - Do Not Use 001 - Do Not Use 010 - 1 Second 011 - 2 Seconds 100 - 3 Seconds 101 - 4 Seconds 110 - 5 Seconds 111 - 6 Seconds TABLE 50: TRANSMIT SPRM AND NPRM CONTROL REGISTER (TSPRMCR) BIT FUNCTION TYPE DEFAULT HEX ADDRESS: 0XN142 DESCRIPTION-OPERATION 7 FC_Bit R/W 0 NPRM FC Bit This bit is used to set the value of the FC bit field within the NPRM report. 6 PA_Bit R/W 0 NPRM PA Bit This bit is used to set the value of the PA bit field within the NPRM report. 5 U1_BIT R/W 0 U1 Bit This bit provides the contents of the U1 bit within the outgoing SPRM message. 64 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 50: TRANSMIT SPRM AND NPRM CONTROL REGISTER (TSPRMCR) BIT 4 FUNCTION U2_BIT 3-0 R_BIT TYPE DEFAULT R/W 0 R/W 0000 REV. 1.0.1 HEX ADDRESS: 0XN142 DESCRIPTION-OPERATION U2 Bit This bit provides the contents of the U2 bit within the outgoing SPRM message. R Bit This bit provides the contents of the R bit within the outgoing SPRM message. 65 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 51: DATA LINK CONTROL REGISTER (DLCR2) BIT 7 FUNCTION SLC-96 Data Link Enable TYPE DEFAULT R/W 0 HEX ADDRESS: 0XN143 DESCRIPTION-OPERATION SLC®96 DataLink Enable This bit permits the user to configure the channel to support the transmission and reception of the “SLC-96 type” of data-link message. 0 - Channel does not support the transmission and reception of “SLC-96” type of data-link messages. Regular SF framing bits will be transmitted. 1 - Channel supports the transmission and reception of the “SLC96” type of data-link messages. NOTE: This bit is only active if the channel has been configured to operate in either the SLC-96 or the ESF Framing formats. 6 MOS ABORT Disable R/W 0 MOS ABORT Disable: This bit permits the user to either enable or disable the “Automatic MOS ABORT” feature within Transmit HDLC Controller # 2. If the user enables this feature, then Transmit HDLC Controller block # 2 will automatically transmit the ABORT Sequence (e.g., a zero followed by a string of 7 consecutive “1s”) whenever it abruptly transitions from transmitting a MOS type of message, to transmitting a BOS type of message. If the user disables this feature, then the Transmit HDLC Controller Block # 2 will NOT transmit the ABORT sequence, whenever it abruptly transitions from transmitting a MOS-type of message to transmitting a BOS-type of message. 0 - Enables the “Automatic MOS Abort” feature 1 - Disables the “Automatic MOS Abort” feature 5 Rx_FCS_DIS R/W 0 Receive Frame Check Sequence (FCS) Verification Enable/Disable This bit permits the user to configure the Receive HDLC Controller Block # 2 to compute and verify the FCS value within each incoming LAPD message frame. 0 - Enables FCS Verification 1 - Disables FCS Verification 4 AutoRx R/W 0 Auto Receive LAPD Message This bit configures the Receive HDLC Controller Block #2 to discard any incoming BOS or LAPD Message frame that exactly match which is currently stored in the Receive HDLC1 buffer. 0 = Disables this “AUTO DISCARD” feature 1 = Enables this “AUTO DISCARD” feature. 3 Tx_ABORT R/W 0 Transmit ABORT This bit configures the Transmit HDLC Controller Block # 2 to transmit an ABORT sequence (string of 7 or more consecutive 1’s) to the Remote terminal. 0 - Configures the Transmit HDLC Controller Block # 2 to function normally (e.g., not transmit the ABORT sequence). 1 - Configures the Transmit HDLC Controller block # 2 to transmit the ABORT Sequence. 66 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 51: DATA LINK CONTROL REGISTER (DLCR2) BIT 2 FUNCTION Tx_IDLE Tx_FCS_EN HEX ADDRESS: 0XN143 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit Idle (Flag Sequence Byte) This bit configures the Transmit HDLC Controller Block #2 to unconditionally transmit a repeating string of Flag Sequence octets (0X7E) in the data link channel to the Remote terminal. In normal conditions, the Transmit HDLC Controller block will repeatedly transmit the Flag Sequence octet whenever there is no MOS message to transmit to the remote terminal equipment. However, if the user invokes this “Transmit Idle Sequence” feature, then the Transmit HDLC Controller block will UNCONDITIONALLY transmit a repeating stream of the Flag Sequence octet (thereby overwriting all outbound MOS data-link messages). 0 - Configures the Transmit HDLC Controller Block # 2 to transmit data-link information in a “normal” manner. 1 - Configures the Transmit HDLC Controller block # 2 to transmit a repeating string of Flag Sequence Octets (0x7E). NOTE: 1 REV. 1.0.1 R/W 0 This bit is ignored if the Transmit HDLC2 controller is operating in the BOS Mode - bit 0 (MOS/BOS) within this register is set to 0. Transmit LAPD Message with Frame Check Sequence (FCS) This bit permits the user to configure the Transmit HDLC Controller block # 2 to compute and append FCS octets to the “back-end” of each outbound MOS data-link message. 0 - Configures the Transmit HDLC Controller block # 2 to NOT compute and append the FCS octets to the back-end of each outbound MOS data-link message. 1 - Configures the Transmit HDLC Controller block # 2 TO COMPUTE and append the FCS octets to the back-end of each outbound MOS data-link message. NOTE: This bit is ignored if the transmit HDLC2 controller has been configured to operate in the BOS mode - bit 0 (MOS/BOS) within this register is set to 0. 0 MOS/BOS R/W 0 Message Oriented Signaling/Bit Oriented Signaling Send This bit permits the user to enable LAPD transmission through HDLC Controller Block # 2 using either BOS (Bit-Oriented Signaling) or MOS (Message-Oriented Signaling) frames. 0 - Transmit HDLC Controller block # 2 BOS message Send. 1 - Transmit HDLC Controller block # 2 MOS message Send. NOTE: This is not an Enable bit. This bit must be set to "0" each time a BOS is to be sent. 67 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 52: TRANSMIT DATA LINK BYTE COUNT REGISTER (TDLBCR2) BIT 7 FUNCTION TxHDLC2 BUFAvail/ BUFSel HEX ADDRESS: 0XN144 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit HDLC2 Buffer Available/Buffer Select This bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. If the user is writing data into this register bit: 0 - Configures the Transmit HDLC2 Controller to read out and transmit the data, residing within “Transmit HDLC2 Buffer # 0", via the Data Link channel to the remote terminal equipment. 1 - Configures the Transmit HDLC2 Controller to read out and transmit the data, residing within the “Transmit HDLC2 Buffer #1”, via the Data Link channel to the remote terminal equipment. If the user is reading data from this register bit: 0 - Indicates that “Transmit HDLC2 Buffer # 0" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC2 Message Buffer, he/she should proceed to write this message into “Transmit HDLC2 Buffer # 0" - Address location: 0xN600. 1 - Indicates that “Transmit HDLC2 Buffer # 1" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC2 Message Buffer, he/she should proceed to write this message into “Transmit HDLC2 Buffer # 1" - Address location: 0xN700. NOTE: If one of these Transmit HDLC2 buffers contain a message which has yet to be completely read-in and processed for transmission by the Transmit HDLC2 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. Changing this bit to the inuse buffer is not permitted. 6-0 TDLBC[6:0] R/W 0000000 Transmit HDLC2 Message - Byte Count The exact function of these bits depends on whether the Transmit HDLC 2 Controller is configured to transmit MOS or BOS messages to the Remote Terminal Equipment. In BOS MODE: These bit fields contain the number of repetitions the BOS message must be transmitted before the Transmit HDLC2 controller generates the Transmit End of Transfer (TxEOT) interrupt and halts transmission. If these fields are set to 00000000, then the BOS message will be transmitted for an indefinite number of times. In MOS MODE: These bit fields contain the length, in number of octets, of the message to be transmitted. The length of MOS message specified in these bits include header bytes such as the SAPI, TEI, Control field, however, it does not include the FCS bytes. 68 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 53: RECEIVE DATA LINK BYTE COUNT REGISTER (RDLBCR2) BIT 7 FUNCTION RBUFPTR 6-0 RDLBC[6:0] REV. 1.0.1 HEX ADDRESS: 0XN145 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Receive HDLC2 Buffer-Pointer This bit Identifies which Receive HDLC2 buffer contains the most recently received HDLC2 message. 0 - Indicates that Receive HDLC2 Buffer # 0 contains the contents of the most recently received HDLC message. 1 - Indicates that Receive HDLC2 Buffer # 1 contains the contents of the most recently received HDLC message. R/W 0000000 Receive HDLC Message - byte count The exact function of these bits depends on whether the Receive HDLC Controller Block #2 is configured to receive MOS or BOS messages. In BOS Mode: These seven bits contain the number of repetitions the BOS message must be received before the Receive HDLC2 controller generates the Receive End of Transfer (RxEOT) interrupt. If these bits are set to “0000000”, the message will be received indefinitely and no Receive End of Transfer (RxEOT) interrupt will be generated. In MOS Mode: These seven bits contain the size in bytes of the HDLC2 message that has been received and written into the Receive HDLC buffer. The length of MOS message shown in these bits include header bytes such as the SAPI, TEI, Control field, AND the FCS bytes. 69 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 54: LOOPBACK CODE CONTROL REGISTER - CODE 3 (LCCR3) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN146 RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 70 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 55: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 3 (RLACR3) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN147 TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 56: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 3 (RLDCR3) BIT REV. 1.0.1 HEX ADDRESS: 0XN148 TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 71 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 57: LOOPBACK CODE CONTROL REGISTER - CODE 4 (LCCR4) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN149 RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 72 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 58: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 4 (RLACR4) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN14A TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 59: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 4 (RLDCR4) BIT REV. 1.0.1 HEX ADDRESS: 0XN14B TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 73 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 60: LOOPBACK CODE CONTROL REGISTER - CODE 5 (LCCR5) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN14C RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 74 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 61: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 5 (RLACR5) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN14D TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 62: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 5 (RLDCR5) BIT REV. 1.0.1 HEX ADDRESS: 0XN14E TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 75 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 63: LOOPBACK CODE CONTROL REGISTER - CODE 6 (LCCR6) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN14F RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 76 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 64: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 6 (RLACR6) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN150 TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 65: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 6 (RLDCR6) BIT REV. 1.0.1 HEX ADDRESS: 0XN151 TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 77 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 66: DATA LINK CONTROL REGISTER (DLCR3) BIT 7 HEX ADDRESS: 0XN153 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION SLC-96 Data Link Enable R/W 0 SLC®96 DataLink Enable This bit permits the user to configure the channel to support the transmission and reception of the “SLC-96 type” of data-link message. 0 - Channel does not support the transmission and reception of “SLC-96” type of data-link messages. Regular SF framing bits will be transmitted. 1 - Channel supports the transmission and reception of the “SLC-96” type of data-link messages. NOTE: This bit is only active if the channel has been configured to operate in either the SLC-96 or the ESF Framing formats. 6 MOS ABORT Disable R/W 0 MOS ABORT Disable: This bit permits the user to either enable or disable the “Automatic MOS ABORT” feature within Transmit HDLC Controller # 3. If the user enables this feature, then Transmit HDLC Controller block # 3 will automatically transmit the ABORT Sequence (e.g., a zero followed by a string of 7 consecutive “1s”) whenever it abruptly transitions from transmitting a MOS type of message, to transmitting a BOS type of message. If the user disables this feature, then the Transmit HDLC Controller Block # 3 will NOT transmit the ABORT sequence, whenever it abruptly transitions from transmitting a MOS-type of message to transmitting a BOS-type of message. 0 - Enables the “Automatic MOS Abort” feature 1 - Disables the “Automatic MOS Abort” feature 5 Rx_FCS_DIS R/W 0 Receive Frame Check Sequence (FCS) Verification Enable/Disable This bit permits the user to configure the Receive HDLC Controller Block # 3 to compute and verify the FCS value within each incoming LAPD message frame. 0 - Enables FCS Verification 1 - Disables FCS Verification 4 AutoRx R/W 0 Auto Receive LAPD Message This bit configures the Receive HDLC Controller Block #3 to discard any incoming BOS or LAPD Message frame that exactly match which is currently stored in the Receive HDLC3 buffer. 0 = Disables this “AUTO DISCARD” feature 1 = Enables this “AUTO DISCARD” feature. 3 Tx_ABORT R/W 0 Transmit ABORT This bit configures the Transmit HDLC Controller Block #3 to transmit an ABORT sequence (string of 7 or more consecutive 1’s) to the Remote terminal. 0 - Configures the Transmit HDLC Controller Block # 3 to function normally (e.g., not transmit the ABORT sequence). 1 - Configures the Transmit HDLC Controller block # 3 to transmit the ABORT Sequence. 78 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 66: DATA LINK CONTROL REGISTER (DLCR3) BIT 2 FUNCTION Tx_IDLE REV. 1.0.1 HEX ADDRESS: 0XN153 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit Idle (Flag Sequence Byte) This bit configures the Transmit HDLC Controller Block #3 to unconditionally transmit a repeating string of Flag Sequence octets (0X7E) in the data link channel to the Remote terminal. In normal conditions, the Transmit HDLC Controller block will repeatedly transmit the Flag Sequence octet whenever there is no MOS message to transmit to the remote terminal equipment. However, if the user invokes this “Transmit Idle Sequence” feature, then the Transmit HDLC Controller block will UNCONDITIONALLY transmit a repeating stream of the Flag Sequence octet (thereby overwriting all outbound MOS data-link messages). 0 - Configures the Transmit HDLC Controller Block # 3 to transmit data-link information in a “normal” manner. 1 - Configures the Transmit HDLC Controller block # 3 to transmit a repeating string of Flag Sequence Octets (0x7E). NOTE: This bit is ignored if the Transmit HDLC3 controller is operating in the BOS Mode - bit 0 (MOS/BOS) within this register is set to 0. 1 Tx_FCS_EN R/W 0 Transmit LAPD Message with Frame Check Sequence (FCS) This bit permits the user to configure the Transmit HDLC Controller block # 3 to compute and append FCS octets to the “back-end” of each outbound MOS data-link message. 0 - Configures the Transmit HDLC Controller block # 3 to NOT compute and append the FCS octets to the back-end of each outbound MOS data-link message. 1 - Configures the Transmit HDLC Controller block # 3 TO COMPUTE and append the FCS octets to the back-end of each outbound MOS data-link message. NOTE: 0 MOS/BOS R/W 0 This bit is ignored if the transmit HDLC3 controller has been configured to operate in the BOS mode - bit 0 (MOS/BOS) within this register is set to 0. Message Oriented Signaling/Bit Oriented Signaling Send This bit permits the user to enable LAPD transmission through HDLC Controller Block # 3 using either BOS (Bit-Oriented Signaling) or MOS (Message-Oriented Signaling) frames. 0 - Transmit HDLC Controller block # 3 BOS message Send. 1 - Transmit HDLC Controller block # 3 MOS message Send. NOTE: This is not an Enable bit. This bit must be set to "0" each time a BOS is to be sent. 79 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 67: TRANSMIT DATA LINK BYTE COUNT REGISTER (TDLBCR3) BIT 7 FUNCTION TxHDLC3 BUFAvail/ BUFSel HEX ADDRESS: 0XN154 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Transmit HDLC3 Buffer Available/Buffer Select This bit has different functions, depending upon whether the user is writing to or reading from this register, as depicted below. If the user is writing data into this register bit: 0 - Configures the Transmit HDLC3 Controller to read out and transmit the data, residing within “Transmit HDLC3 Buffer # 0", via the Data Link channel to the remote terminal equipment. 1 - Configures the Transmit HDLC3 Controller to read out and transmit the data, residing within the “Transmit HDLC3 Buffer #1”, via the Data Link channel to the remote terminal equipment. If the user is reading data from this register bit: 0 - Indicates that “Transmit HDLC3 Buffer # 0" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC3 Message Buffer, he/she should proceed to write this message into “Transmit HDLC3 Buffer # 0" - Address location: 0xN600. 1 - Indicates that “Transmit HDLC3 Buffer # 1" is the next available buffer. In this case, if the user wishes to write in the contents of a new “outbound” Data Link Message into the Transmit HDLC3 Message Buffer, he/she should proceed to write this message into “Transmit HDLC3 Buffer # 1" - Address location: 0xN700. NOTE: If one of these Transmit HDLC3 buffers contain a message which has yet to be completely read-in and processed for transmission by the Transmit HDLC3 controller, then this bit will automatically reflect the value corresponding to the next available buffer when it is read. Changing this bit to the inuse buffer is not permitted. 6-0 TDLBC[6:0] R/W 0000000 Transmit HDLC3 Message - Byte Count The exact function of these bits depends on whether the Transmit HDLC 3 Controller is configured to transmit MOS or BOS messages to the Remote Terminal Equipment. In BOS MODE: These bit fields contain the number of repetitions the BOS message must be transmitted before the Transmit HDLC3 controller generates the Transmit End of Transfer (TxEOT) interrupt and halts transmission. If these fields are set to 00000000, then the BOS message will be transmitted for an indefinite number of times. In MOS MODE: These bit fields contain the length, in number of octets, of the message to be transmitted. The length of MOS message specified in these bits include header bytes such as the SAPI, TEI, Control field, however, it does not include the FCS bytes. 80 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 68: RECEIVE DATA LINK BYTE COUNT REGISTER (RDLBCR3) BIT 7 FUNCTION RBUFPTR 6-0 RDLBC[6:0] REV. 1.0.1 HEX ADDRESS: 0XN155 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Receive HDLC2 Buffer-Pointer This bit Identifies which Receive HDLC3 buffer contains the most recently received HDLC3 message. 0 - Indicates that Receive HDLC3 Buffer # 0 contains the contents of the most recently received HDLC message. 1 - Indicates that Receive HDLC3 Buffer # 1 contains the contents of the most recently received HDLC message. R/W 0000000 Receive HDLC Message - byte count The exact function of these bits depends on whether the Receive HDLC Controller Block #3 is configured to receive MOS or BOS messages. In BOS Mode: These seven bits contain the number of repetitions the BOS message must be received before the Receive HDLC3 controller generates the Receive End of Transfer (RxEOT) interrupt. If these bits are set to “0000000”, the message will be received indefinitely and no Receive End of Transfer (RxEOT) interrupt will be generated. In MOS Mode: These seven bits contain the size in bytes of the HDLC3 message that has been received and written into the Receive HDLC buffer. The length of MOS message shown in these bits include header bytes such as the SAPI, TEI, Control field, AND the FCS bytes. 81 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 69: LOOPBACK CODE CONTROL REGISTER - CODE 7 (LCCR7) BIT FUNCTION 7-6 RXLBCALEN[1:0] TYPE DEFAULT R/W 00 DESCRIPTION-OPERATION Receive Loopback Code Activation Length This bit determines the receive loopback code activation length. There are four lengths supported as presented in the table below: RXLBCALEN[1:0] 5-4 RXLBCDLEN[1:0] R/W 00 RECEIVE LOOPBACK CODE ACTIVATION LENGTH 00 Selects 4-bit receive loopback code activation Sequence 01 Selects 5-bit receive loopback code activation Sequence 10 Selects 6-bit receive loopback code activation Sequence 11 Selects 7-bit receive loopback code activation Sequence Receive Loopback Code Deactivation Length This bit determines the receive loopback code deactivation length. There are four lengths supported as presented in the table below RXLBCDLEN[1:0] 3-2 Reserved HEX ADDRESS: 0XN156 RECEIVE LOOPBACK CODE DEACTIVATION LENGTH 00 Selects 4-bit receive loopback code deactivation Sequence 01 Selects 5-bit receive loopback code deactivation Sequence 10 Selects 6-bit receive loopback code deactivation Sequence 11 Selects 7-bit receive loopback code deactivation Sequence R/W 00 Reserved 1 FRAMED R/W 0 Framed Loopback Code This bit selects either framed or unframed loopback code generation in the transmit path. 0 = Selects an “Unframed” loopback code for transmission. 1 = Selects a “framed” loopback code for transmission. 0 Reserved R/W 0 Reserved 82 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 70: RECEIVE LOOPBACK ACTIVATION CODE REGISTER - CODE 7 (RLACR7) BIT FUNCTION 7-1 RXLBAC[6:0] 0 RXLBACENB FUNCTION 7-1 RXLBDC[6:0] 0 RXLBDCENB HEX ADDRESS: 0XN157 TYPE DEFAULT R/W 1010101 Receive activation loopback code These seven bits determine the receive loopback activation code. The MSB of the receive activation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive activation loopback code enable This bit enables the receive loopback activation code detection. Receive loopback activation code is detected by writing the expected receive activation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback activation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code activation detection. 1 = Enables the receive loopback code activation detection. TABLE 71: RECEIVE LOOPBACK DEACTIVATION CODE REGISTER - CODE 7 (RLDCR7) BIT REV. 1.0.1 HEX ADDRESS: 0XN158 TYPE DEFAULT R/W 1010101 Receive deactivation loopback code These seven bits determine the receive loopback deactivation code. The MSB of the receive deactivation loopback code is received first. R/W 0 DESCRIPTION-OPERATION Receive deactivation loopback code enable This bit enables the receive loopback deactivation code detection. Receive loopback deactivation code is detected by writing the expected receive deactivation loopback code in this register and enabling it using this bit. The length and format of the Receive loopback deactivation code is determined by the Loopback Code Control Register. 0 = Disables the receive loopback code deactivation detection. 1 = Enables the receive loopback code deactivation detection. 83 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 72: BERT CONTROL REGISTER (BCR) BIT FUNCTION TYPE DEFAULT 7-4 Reserved R/W 0 3-0 BERT[3:0] R/W 0000 HEX ADDRESS: 0XN163 DESCRIPTION-OPERATION Reserved BERT Pattern Select 0010 =PRBS X20 + X3 + 1 0011 = QRSS X20 + X17 + 1 0100 = All Ones 0101 = All Zeros 0110 = 3 in 24 0111 = 1 in 8 1000 = 55 Octet Pattern 1001 = Daly Pattern 1010 = PRBS X20 + X17 + 1 Others = Invalid BERT Pattern Definitions 3 in 24 0001 0001 0000 0001 0000 0000 ... 1 in 8 0000 0010 ... 55 Octet (Unframed) This pattern is shown in HEX format for simplification purposes. 01 01 01 01 01 01 80 01 01 01 01 01 01 03 01 01 01 01 07 01 01 01 01 55 55 55 55 AA AA AA AA 01 01 01 01 01 01 FF FF FF FF FF FF 80 01 80 01 80 01 80 01 80 01 80 01 ... Daly Pattern (Framed) This pattern is shown in HEX format for simplification purposes. 01 01 01 01 01 01 80 01 01 01 01 01 01 03 01 01 01 01 07 01 01 01 01 55 55 55 55 AA AA AA AA 01 01 01 01 01 01 FF FF FF FF FF FF 80 01 80 01 80 01 80 01 80 01 80 01 ... 84 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION 1.1 REV. 1.0.1 T1 Synchronization status message T1 synchronization messages are sent through the FDL (Facility Data Link) bits by using a BOC (Bit Oriented Code) controller within the XRT86VX38 device. The most right bit position in the BOC code is sent first. The SSM message that are used in typical BITS applications are shown below. These messages are defined in specification ANSI T1.101-1999. TABLE 73: T1 SSM MESSAGES QUALITY LEVEL DESCRIPTION BOC CODE 1 Stratum 1 Traceable 00000100 11111111 2 Synchronized Traceability Unknown 00001000 11111111 3 Stratum 2 Traceable 00001100 11111111 4 Stratum 3 Traceable 00010000 11111111 5 SONET Minimum Clock Traceable 00100010 11111111 6 Stratum 4 Traceable 00101000 11111111 7 Do Not Use for Synchronization 00110000 11111111 User Assignable Reserved for Network Synchronization Use 01000000 11111111 1.2 T1 BOC Receiver If enabled, the T1 BOC receiver will monitor the FDL bits for SSM messages with various features being supported. Some of these features are Change of Status Alarm, 3 independent pre-set codes for matching validation (each having its own alarm), filter settings for consecutive pattern qualification, and many more. NOTE: If the receive BOC is enabled. the part will still report BOS and MOS messages as described in the register descriptions. 1.3 T1 BOC Transmitter The T1 BOC transmitter will automatically insert an SSM message in the correct FDL bit positions if enabled. Once the message is stored in the TFDL register, Bit 0=1 sends the message, automatically followed by the Abort Sequence. 85 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 74: SSM BOC CONTROL REGISTER (BOCCR 0XN170H) BIT7 BIT6 TxABORT BIT5 RMF[1:0] BIT4 BIT3 RBOCE BOCR BIT2 BIT1 RBF[1:0] BIT0 SBOC R/W R/W R/W R/W Auto Clear R/W R/W Auto Clear 0 0 0 0 0 0 0 0 BIT 7 - Transmit Abort Sequence Enable By default, the transmitter will send an IDLE flag after the SSM message (unless continous is set). To send an Abort sequence to over write the IDLE flag, set this bit to ’1’. } 0 - Disabled } 1 - Enable TxABORT BITS [6:5] - Receive Match Filter Bits These bits are used to set the number of consecutive error free patterns that must be received before the receive Match Event is set. This filter can be set to any message, not just a Valid SSM message. This filter does NOT apply to the RFDL valid message or alarm indication. The RFDL alarm and valid register have their own filter. See BITS [2:1] of this register. } 00 - None } 01 - 3 consecutive patterns } 10 - 5 consecutive patterns } 11 - 7 consecutive patterns BIT 4 - Receive BOC Enable This bit is used to enable the BOC receiver. If this bit is set to "0", only standard BOS messages will be processed by the HDLC controller. For clarification, BOC messages can only be processed through the FDL bits. } 0 - Disabled } 1 - Enable Receive BOC BIT 3 - BOC Reset This bit is used to reset the receive BOC controller. The function of this bit is to reset all the BOC register values to their default values, except the BOC Interrupt registers. This register bit is automatically set back to ’0’ so that the user only needs to write ’1’ to send a subsequent reset. } 1 - Reset BOC BITS [2:1] - Receive BOC Filter Bits These bits are used to set the number of consecutive error free patterns that must be received before the receive BOC alarm indication is set and the RFDL Valid Register is updated. This filter does NOT apply to the RFDL Matching Event registers. The 3 RFDL Matching Event Registers have a separate filter that applies equally to all three matching registers. Therefore, there are a total of 2 filters. } 00 - None } 01 - 3 consecutive patterns } 10 - 5 consecutive patterns } 11 - 7 consecutive patterns BIT 0 - Send BOC Message This bit is used to transmit the stored BOC message in the transmit FDL register. This register bit is automatically set back to ’0’ so that the user only needs to write ’1’ to send a subsequent BOC message. } 0 - Normal Operation } 1 - Send BOC Message 86 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 75: SSM RECEIVE FDL REGISTER (RFDLR 0XN171H) BIT7 BIT6 BIT5 BIT4 BIT3 Reserved BIT2 BIT1 BIT0 RBOC[5:0] RO RO RO RO RO RO RO RO 0 0 0 0 0 0 0 0 BITS [7:6] - Reserved BITS [5:0] - Receive BOC Message These bits contain the most recently received BOC message if the filter setting has been meet in bits[2:1] of register 0xn170h. 87 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 76: SSM RECEIVE FDL MATCH 1 REGISTER (RFDLMR1 0XN172H) BIT7 BIT6 BIT5 BIT4 BIT3 Reserved BIT2 BIT1 BIT0 RFDLM1[5:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 BITS [7:6] - Reserved BITS [5:0] - Receive FDL Match 1 These bits can be used to set an expected value to be compared to the actual receive FDL message. This register is one of three possible expected values that can be set. Upon a match of this register, an independent alarm will be set. In addition, this register has a filter for consecutive message validation. TABLE 77: SSM RECEIVE FDL MATCH 2 REGISTER (RFDLMR2 0XN173H) BIT7 BIT6 BIT5 BIT4 BIT3 Reserved BIT2 BIT1 BIT0 RFDLM2[5:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 BITS [7:6] - Reserved BITS [5:0] - Receive FDL Match 2 These bits can be used to set an expected value to be compared to the actual receive FDL message. This register is one of three possible expected values that can be set. Upon a match of this register, an independent alarm will be set. In addition, this register has a filter for consecutive message validation. TABLE 78: SSM RECEIVE FDL MATCH 3 REGISTER (RFDLMR3 0XN174H) BIT7 BIT6 BIT5 BIT4 BIT3 Reserved BIT2 BIT1 BIT0 RFDLM3[5:0] R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 BITS [7:6] - Reserved BITS [5:0] - Receive FDL Match 3 These bits can be used to set an expected value to be compared to the actual receive FDL message. This register is one of three possible expected values that can be set. Upon a match of this register, an independent alarm will be set. In addition, this register has a filter for consecutive message validation. 88 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 79: SSM TRANSMIT FDL REGISTER (TFDLR 0XN175H) BIT7 BIT6 BIT5 BIT4 BIT3 Reserved BIT2 BIT1 BIT0 TBOC[5:0] RW RW RW RW RW RW RW RW 0 0 0 0 0 0 0 0 BITS [7:6] - Reserved BITS [5:0] - Transmit BOC Message These bits are used to store the BOC message to be transmitted out the FDL bits. Once the message has been stored in this register, Bit 0 within the BOC Control Register is used to automatically transmit the message. NOTE: The TxBYTE Count register 0xN176h is used to set the number of repetitions for this BOC message before the Abort sequence is sent out. The default is one repetition. TABLE 80: SSM TRANSMIT BYTE COUNT REGISTER (TBCR 0XN176H) BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 TBCR[7:0] RW RW RW RW RW RW RW RW 0 0 0 0 0 0 0 1 BITS [7:0] - Transmit Byte Count Value These bits are used to store the amount of repetitions the Transmit BOC message will be sent before an Abort sequence. The default value is "1". If "0" is programmed into this register, the transmit BOC will be set continuously. To stop a continuous transmission, the TxBYTE count should be progammed to a definite value, and then re-send the BOC message. 89 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 81: RECEIVE DS-0 MONITOR REGISTERS (RDS0MR) HEX ADDRESS: 0XN160 TO 0XN16F (NOT INCLUDING 0XN163) AND 0XN1C0 TO 0XN1D0 BIT FUNCTION 7-0 RxDS-0[7:0] TYPE RO DEFAULT DESCRIPTION-OPERATION 00000000 Receive DS-0 Monitor The contents of these registers will display a direct copy of the value currently being processed by the receive framer within the selected time slot. This value will reflect the data present at RTIP/RRING before any conditioning occurs. TS0 = 0xN160 TS1 = 0xN161 TS2 = 0xN162 TS3 = 0xN164 (Note: 0xN163 is not used) TS4 = 0xN165 TS5 = 0xN166 TS6 = 0xN167 TS7 = 0xN168 TS8 = 0xN169 TS9 = 0xN16A TS10 = 0xN16B TS11 = 0xN16C TS12 = 0xN16D TS13 = 0xN16E TS14 = 0xN16F TS15 = 0xN1C0 TS16 = 0xN1C1 TS17 = 0xN1C2 TS18 = 0xN1C3 TS29 = 0xN1C4 TS20 = 0xN1C5 TS21 = 0xN1C6 TS22 = 0xN1C7 TS23= 0xN1C8 NOTE: 0xN1C9 to 0XN1D0 are not used in T1 TABLE 82: TRANSMIT DS-0 MONITOR REGISTERS (TDS0MR) BIT FUNCTION 7-0 TxDS-0[7:0] TYPE RO DEFAULT HEX ADDRESS: 0XN1D1 TO 0XN1F0 DESCRIPTION-OPERATION 00000000 Transmit DS-0 Monitor The contents of these registers will display a direct copy of the value currently being processed by the transmit framer within the selected time slot. This value will reflect the data present at TxSER before any conditioning occurs. For time slot 0, read register 0xN1D1, for time slot 1, read 0xN1D2, etc. up to time slot 23 which is 0xN1E8. For T1 mode, time slots 24 through 31 are not used. 90 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 83: DEVICE ID REGISTER (DEVID) BIT FUNCTION HEX ADDRESS: 0X01FE TYPE DEFAULT RO 0x3C 7-0 DEVID[7:0] DESCRIPTION-OPERATION DEVID This register is used to identify the XRT86VX38 Framer/LIU. The value of this register is 0x3Ch. TABLE 84: REVISION ID REGISTER (REVID) BIT FUNCTION 7-0 REVID[7:0] TYPE RO REV. 1.0.1 HEX ADDRESS: 0X01FF DEFAULT DESCRIPTION-OPERATION 00000001 REVID This register is used to identify the revision number of the XRT86VX38. The value of this register for the first revision is A - 0x01h. NOTE: The content of this register is subject to change when a newer revision of the device is issued. 91 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 85: TRANSMIT CHANNEL CONTROL REGISTER 0-23 (TCCR 0-23) BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION Transmit LAPD Control These bits select which one of the three Transmit LAPD controller is configured to use D/E time slot (Octets 0-23) for transmitting LAPD messages. The following table presents the different settings of these two bits. 7 LAPDcntl[1] R/W 1 6 LAPDcntl[0] R/W 0 LAPDCNTL[1:0] NOTE: 5 - 4 TxZERO[1:0] HEX ADDRESS: 0XN300 TO 0XN317 R/W 00 LAPD CONTROLLER SELECTED 00 Transmit LAPD Controller 1 01 Transmit LAPD Controller 2 10 The TxDE[1:0] bits in the Transmit Signaling and Data Link Select Register (TSDLSR - Register Address - 0xN10A, bit 3-2) determine the data source for D/E time slots. 11 Transmit LAPD Controller 3 All three Transmit LAPD Controllers can use D/E timeslots for transmission. However, only Transmit LAPD Controller 1 can use datalink for transmission. Register 0xN300 represents D/E time slot 0, and 0xN317 represents D/E time slot 23. Selects Type of Zero Suppression These bits select the type of zero code suppression used by the XRT86VX38 device . TXZERO[1:0] TYPE OF ZERO CODE SUPPRESSION SELECTED 00 No zero code suppression is used 01 AT&T bit 7 stuffing is used 10 GTE zero code suppression is used. If GTE zero code suppression is used, bit 8 is stuffed in non-signaling frame. Otherwise, bit 7 is stuffed in signaling frame if signaling bit is zero. 11 DDS zero code suppression is used. The value 0x98 replaces the input data 92 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 85: TRANSMIT CHANNEL CONTROL REGISTER 0-23 (TCCR 0-23) BIT FUNCTION 3-0 TxCond(3:0) REV. 1.0.1 HEX ADDRESS: 0XN300 TO 0XN317 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0000 Transmit Channel Conditioning for Timeslot 0 to 23 These bits allow the user to substitute the input PCM data (Octets 0-23) with internally generated Conditioning Codes prior to transmission to the remote terminal equipment on a per-channel basis. The table below presents the different conditioning codes based on the setting of these bits. Register address 0xN300 represents time slot 0, and address 0xN317 represents time slot 23. TXCOND[1:0] 0xN / 0xE CONDITIONING CODES Contents of timeslot octet are unchanged. 0x1 All 8 bits of the selected timeslot octet are inverted (1’s complement) OUTPUT = (TIME_SLOT_OCTET) XOR 0xFF 0x2 Even bits of the selected timeslot octet are inverted OUTPUT = (TIME_SLOT_OCTET) XOR 0xAA 0x3 Odd bits of the selected time slot octet are inverted OUTPUT = (TIME_SLOT_OCTET) XOR 0x55 0x4 Contents of the selected timeslot octet will be substituted with the 8 -bit value in the Transmit Programmable User Code Register (0xN320-0xN337), 0x5 Contents of the timeslot octet will be substituted with the value 0x7F (BUSY Code) 0x6 Contents of the timeslot octet will be substituted with the value 0xFF (VACANT Code) 0x7 Contents of the timeslot octet will be substituted with the BUSY time slot code (111#_####), where ##### is the Timeslot number 0x8 Contents of the timeslot octet will be substituted with the MOOF code (0x1A) 0x9 Contents of the timeslot octet will be substituted with the A-Law Digital Milliwatt pattern 0xA Contents of the timeslot octet will be substituted with the -Law Digital Milliwatt pattern 0xB The MSB (bit 1) of input data is inverted 0xC All input data except MSB is inverted 0xD Contents of the timeslot octet will be substituted with the PRBS X15 + X 14 + 1/QRTS pattern NOTE: PRBS X15 + X 14 + 1 or QRTS pattern depends on PRBSType selected in the register 0xN123 - bit 7 0xF D/E time slot - The TxDE[2:0] bits in the Transmit Signaling and Data Link Select Register (0xN10A) will determine the data source for D/E time slots. 93 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 86: TRANSMIT USER CODE REGISTER 0-23 (TUCR 0-23) BIT 7-0 FUNCTION TUCR[7:0] TYPE R/W DEFAULT HEX ADDRESS: 0XN320 TO 0XN337 DESCRIPTION-OPERATION b00010111 Transmit Programmable User code. These eight bits allow users to program any code in this register to replace the input PCM data when the Transmit Channel Control Register (TCCR) is configured to replace timeslot octet with programmable user code. (i.e. if TCCR is set to ‘0x4’) The default value of this register is an IDLE Code (b00010111). 94 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 87: TRANSMIT SIGNALING CONTROL REGISTER 0-23 (TSCR 0-23) BIT 7 FUNCTION A (x) REV. 1.0.1 HEX ADDRESS: 0XN340 TO 0XN357 TYPE DEFAULT DESCRIPTION-OPERATION R/W See Note Transmit Signaling bit A This bit allows user to provide signaling Bit A (Octets 0-23) if Robbed-bit signaling is enabled (Rob_Enb bit of this register set to 1) and if signalling data is inserted from TSCR (TxSIGSRC[1:0] = 01 in this register). NOTE: Register 0xN340 represents signaling data for Time Slot 0, and 0xN357 represents signaling data for Time Slot 23. 6 B (y) R/W See Note Transmit Signaling bit B This bit allows user to provide signaling Bit B (Octets 0-23) if Robbed-bit signaling is enabled (Rob_Enb bit of this register set to 1) and if signalling data is inserted from TSCR (TxSIGSRC[1:0] = 01 in this register). NOTE: Register 0xN340 represents signaling data for Time Slot 0, and 0xN357 represents signaling data for Time Slot 23. 5 C (x) R/W See Note Transmit Signaling bit C This bit allows user to provide signaling Bit C (Octets 0-23) if Robbed-bit signaling is enabled (Rob_Enb bit of this register set to 1) and if signalling data is inserted from TSCR (TxSIGSRC[1:0] = 01 in this register). NOTE: Register 0xN340 represents signaling data for Time Slot 0, and 0xN357 represents signaling data for Time Slot 23. 4 D (x) R/W See Note Transmit Signaling bit D This bit allows user to provide signaling Bit D (Octets 0-23) if Robbed-bit signaling is enabled (Rob_Enb bit of this register set to 1) and if signalling data is inserted from TSCR (TxSIGSRC[1:0] = 01 in this register). NOTE: Register 0xN340 represents signaling data for Time Slot 0, and 0xN357 represents signaling data for Time Slot 23. 3 Reserved - See Note Reserved 2 Rob_Enb R/W See Note Robbed-bit signaling enable This bit enables or disables Robbed-bit signaling transmission. If robbed-bit signaling is enabled, signaling data is conveyed in the 8th position of each signaling channel by replacing the original LSB of the voice channel with signaling data. 0 = Disables Robbed-bit signaling. 1 = Enables Robbed-bit signaling. 95 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 87: TRANSMIT SIGNALING CONTROL REGISTER 0-23 (TSCR 0-23) BIT FUNCTION HEX ADDRESS: 0XN340 TO 0XN357 TYPE DEFAULT DESCRIPTION-OPERATION Channel signaling control These bits determine the source for signaling information, see table below. 1 TxSIGSRC[1] R/W See Note 0 TxSIGSRC[0] R/W See Note TXSIGSRC[1:0] SIGNALING SOURCE SELECTED 00/11 Signaling data is inserted from input PCM data (TxSERn pin) 01 Signaling data is inserted from this register (TSCRs). 10 Signaling data is inserted from the Transmit Signaling input pin (TxSIG_n) if the Transmit Signaling Interface bit is enabled (i.e. TxFr1544 bit = 1 in the Transmit Interface Control Register (TICR) Register 0xN120), NOTE: The default value for register address 0xN340 = 0xN1, 0xN341-0xN34F = 0xD0, 0xN350 = 0xB3, 0xN351-0xN35F = 0xD0 96 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 88: RECEIVE CHANNEL CONTROL REGISTER 0-23 (RCCR 0-23) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN360 TO 0XN377 TYPE DEFAULT DESCRIPTION-OPERATION Receive LAPD Control These bits select which one of the three Receive LAPD controller will be configured to use D/E time slot (Octets 0-23) for receiving LAPD messages. 7 LAPDcntl[1] R/W 1 6 LAPDcntl[0] R/W 0 LAPDCNTL[1:0] RECEIVE LAPD CONTROLLER SELECTED 00 Receive LAPD Controller 1 01 Receive LAPD Controller 2 10 The RxDE[1:0] bits in the Receive Signaling and Data Link Select Register (RSDLSR Address - 0xN10C) determine the data source for Receive D/E time slots. 11 Receive LAPD Controller 3 NOTE: All three LAPD Controller can use D/E timeslots for receiving LAPD messages. However, only LAPD Controller 1 can use datalink for reception. NOTE: Register 0xN360 represents D/E time slot 0, and 0xN377 represents D/E time slot 23. 5-4 RxZERO[1:0] R/W 00 Type of Zero Suppression These bits select the type of zero code suppression used by the XRT86VX38 device. RXZERO[1:0] TYPE OF ZERO CODE SUPPRESSION SELECTED 00 No zero code suppression is used 01 AT&T bit 7 stuffing is used 10 GTE zero code suppression is used. If GTE zero code suppression is used, bit 8 is stuffed in non-signaling frame. Otherwise, bit 7 is stuffed in signaling frame if signaling bit is zero. 11 DDS zero code suppression is used. The value 0x98 replaces the input data 97 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 88: RECEIVE CHANNEL CONTROL REGISTER 0-23 (RCCR 0-23) BIT HEX ADDRESS: 0XN360 TO 0XN377 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 3-0 RxCOND[3:0] R/W 0000 Receive Channel Conditioning for Timeslot 0 to 23 These bits allow the user to substitute the input line data (Octets 0-23) with internally generated Conditioning Codes prior to transmission to the backplane interface on a per-channel basis. The table below presents the different conditioning codes based on the setting of these bits. NOTE: Register address 0xN300 represents time slot 0, and address 0xN317 represents time slot 23. RXCOND[1:0] 0xN / 0xE CONDITIONING CODES Contents of timeslot octet are unchanged. 0x1 All 8 bits of the selected timeslot octet are inverted (1’s complement) OUTPUT = (TIME_SLOT_OCTET) XOR 0xFF 0x2 Even bits of the selected timeslot octet are inverted OUTPUT = (TIME_SLOT_OCTET) XOR 0xAA 0x3 Odd bits of the selected time slot octet are inverted OUTPUT = (TIME_SLOT_OCTET) XOR 0x55 0x4 Contents of the selected timeslot octet will be substituted with the 8 -bit value in the Receive Programmable User Code Register (0xN380-0xN397), 0x5 Contents of the timeslot octet will be substituted with the value 0x7F (BUSY Code) 0x6 Contents of the timeslot octet will be substituted with the value 0xFF (VACANT Code) 0x7 Contents of the timeslot octet will be substituted with the BUSY time slot code (111#_####), where ##### is the Timeslot number 0x8 Contents of the timeslot octet will be substituted with the MOOF code (0x1A) 0x9 Contents of the timeslot octet will be substituted with the A-Law Digital Milliwatt pattern 0xA Contents of the timeslot octet will be substituted with the -Law Digital Milliwatt pattern 0xB The MSB (bit 1) of input data is inverted 0xC All input data except MSB is inverted 0xD Contents of the timeslot octet will be substituted with the PRBS X15 + X 14 + 1/QRTS pattern NOTE: PRBS X15 + X 14 + 1 or QRTS pattern depends on PRBSType selected in the register 0xN123 - bit 7 0xF D/E time slot - The RxDE[2:0] bits in the Transmit Signaling and Data Link Select Register (0xN10C) will determine the data source for Receive D/E time slots. 98 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 89: RECEIVE USER CODE REGISTER 0-23 (RUCR 0-23) BIT FUNCTION 7-0 RxUSER[7:0] REV. 1.0.1 HEX ADDRESS: 0XN380 TO 0XN397 TYPE DEFAULT DESCRIPTION-OPERATION R/W 11111111 Receive Programmable User code. These eight bits allow users to program any code in this register to replace the received data when the Receive Channel Control Register (RCCR) is configured to replace timeslot octet with the receive programmable user code. (i.e. if RCCR is set to ‘0x4’) 99 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 90: RECEIVE SIGNALING CONTROL REGISTER 0-23 (RSCR 0-23) BIT FUNCTION HEX ADDRESS: 0XN3A0 TO 0XN3B7 TYPE DEFAULT DESCRIPTION-OPERATION 6 SIGC_ENB R/W 0 Signaling substitution enable This bit enables or disables signaling substitution on the receive side. Once signaling substitution is enabled, received signaling bits ABCD will be substituted with the ABCD values in the Receive Substitution Signaling Register (RSSR). Signaling substitution only occurs in the output PCM data (RxSERn). Receive Signaling Array Register (RSAR - Address 0xN500-0xN51F) and the external Signaling bus (RxSIG_n) output pin will not be affected. 0 = Disables signaling substitution on the receive side. 1 = Enables signaling substitution on the receive side. 5 OH_ENB R/W 0 Signaling OH interface output enable This bit enables or disables signaling information to output via the Receive Overhead pin (RxOH_n). The signaling information in the receive signaling array registers (RSAR - Address 0xN500-0xN51F) is output to the receive overhead output pin (RxOH_n) if this bit is enabled. 0 = Disables signaling information to output via RxOH_n. 1 = Enables signaling information to output via RxOH_n. 4 DEB_ENB R/W 0 Per-channel debounce enable This bit enables or disables the signaling debounce feature. When this feature is enabled, the per-channel signaling state must be in the same state for 2 superframes before the Receive Framer updates signaling information on the Receive Signaling Array Register (RSAR) and the Signaling Pin (RxSIGn). If the signaling bits for two consecutive superframes are not the same, the current state of RSAR and RxSIG will not change. When this feature is disabled, RSAR and RxSIG will be updated as soon as the receive signaling bits have changed. 0 = Disables the Signaling Debounce feature. 1 = Enables the Signaling Debounce feature. 100 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 90: RECEIVE SIGNALING CONTROL REGISTER 0-23 (RSCR 0-23) BIT FUNCTION 3-2 RxSIGC[1:0]] HEX ADDRESS: 0XN3A0 TO 0XN3B7 TYPE DEFAULT DESCRIPTION-OPERATION R/W 00 Signaling conditioning [1:0] These bits allow user to select the format of signaling substitution on a per-channel basis, as presented in the table below. RXSIGC[1:0] 1-0 RxSIGE[1:0] REV. 1.0.1 R/W 00 SIGNALING SUBSTITUTION SCHEMES 00 Substitutes all signaling bits with one. 01 Enables 16-code (A,B,C,D) signaling substitution. Users must write to bits 3-0 in the Receive Signaling Substitution Register (RSSR) to provide the 16-code (A,B,C,D) signaling substitution values. 10 Enables 4-code (A,B) signaling substitution. Users must write to bits 4-5 in the Receive Signaling Substitution Register (RSSR) to provide the 4-code (A,B) signaling substitution values. 11 Enables 2-code (A) signaling substitution. Users must write to bit 6 in the Receive Signaling Substitution Register (RSSR) to provide the 2-code (A) signaling substitution values. Receive Signaling Extraction [1:0] These bits control per-channel signaling extraction as presented in the table below. Signaling information can be extracted to the Receive Signaling Array Register (RSAR), the Receive Signaling Output pin (RxSIG_n) if the Receive SIgnaling Interface is enable, or the Receive Overhead Interface output (RxOH_n) if OH_ENB bit is enabled. (bit 5 of this register). RXSIGE[1:0] SIGNALING EXTRACTION SCHEMES 00 No signaling information is extracted. 01 Enables 16-code (A,B,C,D) signaling extraction. All signaling bits A,B,C,D will be extracted. 10 Enables 4-code (A,B) signaling extraction Only signaling bits A,B will be extracted. 11 Enables 2-code (A) signaling extraction Only signaling bit A will be extracted. 101 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 91: RECEIVE SUBSTITUTION SIGNALING REGISTER 0-23 (RSSR 0-23) 0XN3D7 BIT FUNCTION 7-4 Reserved TYPE DEFAULT - - Reserved HEX ADDRESS: 0XN3C0 TO DESCRIPTION-OPERATION 3 SIG16-A, 4-A, 2-A R/W 0 16-code/4-code/2-code Signaling Bit A This bit provides the value of signaling bit A to substitute the receive signaling bit A when 16-code or 4-code or 2-code signaling substitution is enabled. 2 SIG16-B, 4-B, 2-A R/W 0 16-code/4-code Signaling Bit B This bit provides the value of signaling bit B to substitute the receive signaling bit B when 16-code or 4-code signaling substitution is enabled. 1 SIG16-C, 4-A, 2-A R/W 0 16-code Signaling Bit C This bit provides the value of signaling bit C to substitute the receive signaling bit C when 16-code signaling substitution is enabled. 0 SIG16-D, 4-B, 2-A R/W 0 16-code Signaling Bit D This bit provides the value of signaling bit D to substitute the receive signaling bit D when 16-code signaling substitution is enabled. 102 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 92: RECEIVE SIGNALING ARRAY REGISTER 0 TO 23 (RSAR 0-23) BIT FUNCTION 7-4 Reserved REV. 1.0.1 HEX ADDRESS: 0XN500 TO 0XN517 TYPE DEFAULT - - Reserved These READ ONLY registers reflect the most recently received signaling value (A,B,C,D) associated with timeslot 0 to 31. If signaling debounce feature is enabled, the received signaling state must be the same for 2 superframes before this register is updated. If the signaling bits for two consecutive superframes are not the same, the current value of this register will not be changed. When Bit 7 within register 0xN107 is set to ’1’, signaling bits in this register are updated on superframe boundary If the signaling debounce feature is disabled or if Bit 7 within register 0xN107 is set to ’0’, this register is updated as soon as the received signaling bits have changed. 3 A RO 0 2 B RO 0 1 C RO 0 0 D RO 0 DESCRIPTION-OPERATION NOTE: The content of this register only has meaning when robbedbit signaling is enabled. 103 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 93: LAPD BUFFER 0 CONTROL REGISTER (LAPDBCR0) BIT FUNCTION 7-0 LAPD Buffer 0 HEX ADDRESS: 0XN600 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 LAPD Buffer 0 (96-Bytes) Auto Incrementing This register is used to transmit and receive LAPD messages within buffer 0 of the HDLC controller. Any one of the three HDLC controller can be chosen in the LAPD Select Register (0xN11B). Users should determine the next available buffer by reading the BUFAVAL bit (bit 7 of the Transmit Data Link Byte Count Register 1 (address 0xN114), Register 2 (0xN144) and Register 3 (0xN154) depending on which HDLC controller is selected. If buffer 0 is available, writing to buffer 0 will insert the message into the outgoing LAPD frame after the LAPD message is sent and the data from the transmit buffer cannot be retrieved. After detecting the Receive end of transfer interrupt (RxEOT), users should read the RBUFPTR bit (bit 7 of the Receive Data Link Byte Count Register 1 (address 0xN115), Register 2 (0xN145), or Register 3 (0xN155) depending on which HDLC controller is selected) to determine which buffer contains the received LAPD message ready to be read. If RBUFPTR bit indicates that buffer 0 is available to be read, reading buffer 0 (Register 0xN600) continuously will retrieve the entire received LAPD message. NOTE: When writing to or reading from Buffer 0, the register is automatically incremented such that the entire 96 Byte LAPD message can be written into or read from buffer 0 (Register 0xN600) continuously. TABLE 94: LAPD BUFFER 1 CONTROL REGISTER (LAPDBCR1) BIT FUNCTION 7-0 LAPD Buffer 1 HEX ADDRESS: 0XN700 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 LAPD Buffer 1 (96-Bytes) Auto Incrementing This register is used to transmit and receive LAPD messages within buffer 1 of the HDLC controller. Any one of the three HDLC controller can be is chosen in the LAPD Select Register (0xN11B). Users should determine the next available buffer by reading the BUFAVAL bit (bit 7 of the Transmit Data Link Byte Count Register 1 (address 0xN114), Register 2 (0xN144) and Register 3 (0xN154) depending on which HDLC controller is selected. If buffer 1 is available, writing to buffer 1 will insert the message into the outgoing LAPD frame after the LAPD message is sent and the data from the transmit buffer 1 cannot be retrieved. After detecting the Receive end of transfer interrupt (RxEOT), users should read the RBUFPTR bit (bit 7 of the Receive Data Link Byte Count Register 1 (address 0xN115), Register 2 (0xN145), or Register 3 (0xN155) depending on which HDLC controller is selected) to determine which buffer contains the received LAPD message ready to be read. If RBUFPTR bit indicates that buffer 1 is available to be read, reading buffer 1 (Register 0xN700) continuously will retrieve the entire received LAPD message. NOTE: When writing to or reading from Buffer 0, the register is automatically incremented such that the entire 96 Byte LAPD message can be written into or read from buffer 0 (Register 0xN600) continuously. 104 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 95: PMON RECEIVE LINE CODE VIOLATION COUNTER MSB (RLCVCU) BIT FUNCTION DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Line Code Violation” 16-bit Counter - Upper Byte: These RESET-upon-READ bits, along with that within the PMON Receive Line Code Violation Counter Register LSB combine to reflect the cumulative number of instances that Line Code Violation has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Most Significant byte of this 16-bit of the Line Code Violation counter. RLCVC[15] RUR 0 6 RLCVC[14] RUR 0 5 RLCVC[13] RUR 0 4 RLCVC[12] RUR 0 3 RLCVC[11] RUR 0 2 RLCVC[10] RUR 0 1 RLCVC[9] RUR 0 0 RLCVC[8] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. TABLE 96: PMON RECEIVE LINE CODE VIOLATION COUNTER LSB (RLCVCL) FUNCTION HEX ADDRESS: 0XN900 TYPE 7 BIT REV. 1.0.1 HEX ADDRESS: 0XN901 TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Line Code Violation” 16-bit Counter - Lower Byte: These RESET-upon-READ bits, along with that within the PMON Receive Line Code Violation Counter Register MSB combine to reflect the cumulative number of instances that Line Code Violation has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Least Significant byte of this 16-bit of the Line Code Violation counter. 7 RLCVC[7] RUR 0 6 RLCVC[6] RUR 0 5 RLCVC[5] RUR 0 4 RLCVC[4] RUR 0 3 RLCVC[3] RUR 0 2 RLCVC[2] RUR 0 1 RLCVC[1] RUR 0 0 RLCVC[0] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. 105 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 . TABLE 97: PMON RECEIVE FRAMING ALIGNMENT BIT ERROR COUNTER MSB (RFAECU) HEX ADDRESS: 0XN902 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Framing Alignment Error 16-Bit counter” - Upper Byte: These RESET-upon-READ bits, along with that within the “PMON Receive Framing Alignment Error Counter Register LSB” combine to reflect the cumulative number of instances that the Receive Framing Alignment errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Most Significant byte of this 16-bit of the Receive Framing Alignment Error counter. 7 RFAEC[15] RUR 0 6 RFAEC[14] RUR 0 5 RFAEC[13] RUR 0 4 RFAEC[12] RUR 0 3 RFAEC[11] RUR 0 2 RFAEC[10] RUR 0 1 RFAEC[9] RUR 0 0 RFAEC[8] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. . TABLE 98: PMON RECEIVE FRAMING ALIGNMENT BIT ERROR COUNTER LSB (RFAECL) BIT FUNCTION HEX ADDRESS: 0XN903 TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Framing Alignment Error 16-Bit Counter” - Lower Byte: These RESET-upon-READ bits, along with that within the “PMON Receive Framing Alignment Error Counter Register MSB” combine to reflect the cumulative number of instances that the Receive Framing Alignment errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Least Significant byte of this 16-bit of the Receive Framing Alignment Error counter. 7 RFAEC[7] RUR 0 6 RFAEC[6] RUR 0 5 RFAEC[5] RUR 0 4 RFAEC[4] RUR 0 3 RFAEC[3] RUR 0 2 RFAEC[2] RUR 0 1 RFAEC[1] RUR 0 0 RFAEC[0] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. 106 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 99: PMON RECEIVE SEVERELY ERRORED FRAME COUNTER (RSEFC) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN904 TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - Receive Severely Errored frame Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Receive Severely Errored Frames have been detected by the T1 Framer since the last read of this register. in T1 mode, Severely Errored Frame is defined as having framing bit errors in contiguous windows. In T1 SF mode, SEF is defined if Ft bits have been received consecutively in errors for 0.75ms or 6 SF frames. In T1 ESF mode, SEF is defined if FPS bit have been received consecutively in errors for 3 ms or 24 ESF frames. 7 RSEFC[7] RUR 0 6 RSEFC[6] RUR 0 5 RSEFC[5] RUR 0 4 RSEFC[4] RUR 0 3 RSEFC[3] RUR 0 2 RSEFC[2] RUR 0 1 RSEFC[1] RUR 0 0 RSEFC[0] RUR 0 107 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 100: PMON RECEIVE CRC-6 BIT ERROR COUNTER - MSB (RSBBECU) BIT FUNCTION HEX ADDRESS: 0XN905 TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Synchronization Bit Error 16-Bit Counter” - Upper Byte: These RESET-upon-READ bits, along with that within the “PMON Receive Synchronization Bit Error Counter Register LSB” combine to reflect the cumulative number of instances that the Receive Synchronization Bit errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Most Significant byte of this 16-bit of the Receive Synchronization Bit Error counter. 7 RSBBEC[15] RUR 0 6 RSBBEC[14] RUR 0 5 RSBBEC[13] RUR 0 4 RSBBEC[12] RUR 0 3 RSBBEC[11] RUR 0 2 RSBBEC[10] RUR 0 1 RSBBEC[9] RUR 0 0 RSBBEC[8] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. TABLE 101: PMON RECEIVE CRC-6 BIT ERROR COUNTER - LSB (RSBBECL) 0XN906 BIT FUNCTION HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor “Receive Synchronization Bit Error 16-Bit Counter” - Lower Byte: These RESET-upon-READ bits, along with that within the “PMON Receive Synchronization Bit Error Counter Register MSB” combine to reflect the cumulative number of instances that the Receive Synchronization Bit errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Least Significant byte of this 16-bit of the Receive Synchronization Bit Error counter. 7 RSBBEC[7] RUR 0 6 RSBBEC[6] RUR 0 5 RSBBEC[5] RUR 0 4 RSBBEC[4] RUR 0 3 RSBBEC[3] RUR 0 2 RSBBEC[2] RUR 0 1 RSBBEC[1] RUR 0 0 RSBBEC[0] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. 108 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 102: PMON RECEIVE SLIP COUNTER (RSC) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN909 TYPE DEFAULT DESCRIPTION-OPERATION 7 RSC[7] RUR 0 6 RSC[6] RUR 0 5 RSC[5] RUR 0 Performance Monitor - Receive Slip Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Receive Slip events have been detected by the T1 Framer since the last read of this register. 4 RSC[4] RUR 0 NOTE: A slip event is defined as a replication or deletion of a T1 frame by the receive slip buffer. 3 RSC[3] RUR 0 2 RSC[2] RUR 0 1 RSC[1] RUR 0 0 RSC[0] RUR 0 TABLE 103: PMON RECEIVE LOSS OF FRAME COUNTER (RLFC) BIT FUNCTION HEX ADDRESS: 0XN90A TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - Receive Loss of Frame Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Receive Loss of Frame condition have been detected by the T1 Framer since the last read of this register. 7 RLFC[7] RUR 0 6 RLFC[6] RUR 0 5 RLFC[5] RUR 0 4 RLFC[4] RUR 0 3 RLFC[3] RUR 0 2 RLFC[2] RUR 0 1 RLFC[1] RUR 0 0 RLFC[0] RUR 0 NOTE: This counter counts once every time the Loss of Frame condition is declared. This counter provides the capability to measure an accumulation of short failure events. TABLE 104: PMON RECEIVE CHANGE OF FRAME ALIGNMENT COUNTER (RCFAC) 0XN90B BIT FUNCTION HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - Receive Change of Frame Alignment Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Receive Change of Framing Alignment have been detected by the T1 Framer since the last read of this register. 7 RCFAC[7] RUR 0 6 RCFAC[6] RUR 0 5 RCFAC[5] RUR 0 4 RCFAC[4] RUR 0 3 RCFAC[3] RUR 0 2 RCFAC[2] RUR 0 1 RCFAC[1] RUR 0 0 RCFAC[0] RUR 0 NOTE: Change of Framing Alignment (COFA) is declared when the newly-locked framing pattern is different from the one offered by off-line framer. 109 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 105: PMON LAPD1 FRAME CHECK SEQUENCE ERROR COUNTER 1 (LFCSEC1) 0XN90C BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - LAPD 1 Frame Check Sequence Error Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Frame Check Sequence Error have been detected by the LAPD Controller 1 since the last read of this register. 7 FCSEC1[7] RUR 0 6 FCSEC1[6] RUR 0 5 FCSEC1[5] RUR 0 4 FCSEC1[4] RUR 0 3 FCSEC1[3] RUR 0 2 FCSEC1[2] RUR 0 1 FCSEC1[1] RUR 0 0 FCSEC1[0] RUR 0 TABLE 106: PRBS BIT ERROR COUNTER MSB (PBECU) BIT FUNCTION DEFAULT DESCRIPTION-OPERATION Performance Monitor - T1 PRBS Bit Error 16-Bit Counter Upper Byte: These RESET-upon-READ bits, along with that within the “PMON T1 PRBS Bit Error Counter Register LSB” combine to reflect the cumulative number of instances that the ReceiveT1 PRBS Bit errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Most Significant byte of this 16-bit of the Receive T1 PRBS Bit Error counter. PRBSE[15] RUR 0 6 PRBSE[14] RUR 0 5 PRBSE[13] RUR 0 4 PRBSE[12] RUR 0 3 PRBSE[11] RUR 0 2 PRBSE[10] RUR 0 1 PRBSE[9] RUR 0 0 PRBSE[8] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. TABLE 107: PRBS BIT ERROR COUNTER LSB (PBECL) FUNCTION HEX ADDRESS: 0XN90D TYPE 7 BIT HEX ADDRESS: HEX ADDRESS: 0XN90E TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - T1 PRBS Bit Error 16-Bit Counter Lower Byte: These RESET-upon-READ bits, along with that within the “PMON T1 PRBS Bit Error Counter Register MSB” combine to reflect the cumulative number of instances that the ReceiveT1 PRBS Bit errors has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Least Significant byte of this 16-bit of the Receive T1 PRBS Bit Error counter. 7 PRBSE[7] RUR 0 6 PRBSE[6] RUR 0 5 PRBSE[5] RUR 0 4 PRBSE[4] RUR 0 3 PRBSE[3] RUR 0 2 PRBSE[2] RUR 0 1 PRBSE[1] RUR 0 0 PRBSE[0] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. 110 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 108: TRANSMIT SLIP COUNTER (TSC) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XN90F TYPE DEFAULT DESCRIPTION-OPERATION 7 TxSLIP[7] RUR 0 6 TxSLIP[6] RUR 0 5 TxSLIP[5] RUR 0 Performance Monitor - Transmit Slip Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Transmit Slip events have been detected by the T1 Framer since the last read of this register. 4 TxSLIP[4] RUR 0 NOTE: A slip event is defined as a replication or deletion of a T1 frame by the transmit slip buffer. 3 TxSLIP[3] RUR 0 2 TxSLIP[2] RUR 0 1 TxSLIP[1] RUR 0 0 TxSLIP[0] RUR 0 TABLE 109: EXCESSIVE ZERO VIOLATION COUNTER MSB (EZVCU) BIT FUNCTION TYPE DEFAULT 7 EZVC[15] RUR 0 6 EZVC[14] RUR 0 5 EZVC[13] RUR 0 4 EZVC[12] RUR 0 3 EZVC[11] RUR 0 2 EZVC[10] RUR 0 1 EZVC[9] RUR 0 0 EZVC[8] RUR 0 DESCRIPTION-OPERATION Performance Monitor - T1 Excessive Zero Violation 16-Bit Counter - Upper Byte: These RESET-upon-READ bits, along with that within the “PMON T1 Excessive Zero Violation Counter Register LSB” combine to reflect the cumulative number of instances that the ReceiveT1 Excessive Zero Violation has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Most Significant byte of this 16-bit of the Receive T1 Excessive Zero Violation counter. NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. TABLE 110: EXCESSIVE ZERO VIOLATION COUNTER LSB (EZVCL) BIT FUNCTION HEX ADDRESS: 0XN910 HEX ADDRESS: 0XN911 TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - T1 Excessive Zero Violation 16-Bit Counter - Lower Byte: These RESET-upon-READ bits, along with that within the “PMON T1 Excessive Zero Violation Counter Register MSB” combine to reflect the cumulative number of instances that the ReceiveT1 Excessive Zero Violation has been detected by the Receive T1 Framer block since the last read of this register. This register contains the Least Significant byte of this 16-bit of the Receive T1 Excessive Zero Violation counter. 7 EZVC[7] RUR 0 6 EZVC[6] RUR 0 5 EZVC[5] RUR 0 4 EZVC[4] RUR 0 3 EZVC[3] RUR 0 2 EZVC[2] RUR 0 1 EZVC[1] RUR 0 0 EZVC[0] RUR 0 NOTE: For all 16-bit wide PMON registers, user must read the MSB counter first before reading the LSB counter in order to read the accurate PMON counts. To clear PMON count, user must read the MSB counter first before reading the LSB counter in order to clear the PMON count. 111 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 111: PMON LAPD2 FRAME CHECK SEQUENCE ERROR COUNTER 2 (LFCSEC2) 0XN91C BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - LAPD 2 Frame Check Sequence Error Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Frame Check Sequence Error have been detected by the LAPD Controller 2 since the last read of this register. 7 FCSEC2[7] RUR 0 6 FCSEC2[6] RUR 0 5 FCSEC2[5] RUR 0 4 FCSEC2[4] RUR 0 3 FCSEC2[3] RUR 0 2 FCSEC2[2] RUR 0 1 FCSEC2[1] RUR 0 0 FCSEC2[0] RUR 0 TABLE 112: PMON LAPD2 FRAME CHECK SEQUENCE ERROR COUNTER 3 (LFCSEC3) 0XN92C BIT FUNCTION HEX ADDRESS: HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION Performance Monitor - LAPD 3 Frame Check Sequence Error Counter (8-bit Counter) These Reset-Upon-Read bit fields reflect the cumulative number of instances that Frame Check Sequence Error have been detected by the LAPD Controller 3 since the last read of this register. 7 FCSEC3[7] RUR 0 6 FCSEC3[6] RUR 0 5 FCSEC3[5] RUR 0 4 FCSEC3[4] RUR 0 3 FCSEC3[3] RUR 0 2 FCSEC3[2] RUR 0 1 FCSEC3[1] RUR 0 0 FCSEC3[0] RUR 0 112 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 113: BLOCK INTERRUPT STATUS REGISTER (BISR) BIT FUNCTION 7 Reserved 6 LBCODE TYPE RxClkLOS HEX ADDRESS: 0XNB00 DEFAULT DESCRIPTION-OPERATION For E1 mode only RO 0 Loopback Code Block Interrupt Status This bit indicates whether or not the Loopback Code block has an interrupt request awaiting service. 0 - Indicates no outstanding Loopback Code Block interrupt request is awaiting service 1 - Indicates the Loopback Code block has an interrupt request awaiting service. Interrupt Service routine should branch to the interrupt source and read the Loopback Code Interrupt Status register (address 0xNB0A) to clear the interrupt NOTE: 5 REV. 1.0.1 RO 0 This bit will be reset to 0 after the microprocessor has performed a read to the Loopback Code Interrupt Status Register. Loss of Recovered Clock Interrupt Status This bit indicates whether or not the T1 receive framer is currently declaring the "Loss of Recovered Clock" interrupt. 0 = Indicates that the T1 Receive Framer Block is NOT currently declaring the "Loss of Recovered Clock" interrupt. 1 = Indicates that the T1 Receive Framer Block is currently declaring the "Loss of Recovered Clock" interrupt. NOTE: This bit is only active if the clock loss detection feature is enabled (Register - 0xN100) 4 ONESEC RO 0 One Second Interrupt Status This bit indicates whether or not the T1 receive framer block is currently declaring the "One Second" interrupt. 0 = Indicates that the T1 Receive Framer Block is NOT currently declaring the "One Second" interrupt. 1 = Indicates that the T1 Receive Framer Block is currently declaring the "One Second" interrupt. 3 HDLC RO 0 HDLC Block Interrupt Status This bit indicates whether or not the HDLC block has any interrupt request awaiting service. 0 = Indicates no outstanding HDLC block interrupt request is awaiting service 1 = Indicates HDLC Block has an interrupt request awaiting service. Interrupt Service routine should branch to the interrupt source and read the corresponding Data LInk Status Registers (address 0xNB06, 0xNB16, 0xNB26, 0xNB10, 0xNB18, 0xNB28) to clear the interrupt. NOTE: This bit will be reset to 0 after the microprocessor has performed a read to the corresponding Data Link Status Registers that generated the interrupt. 113 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 113: BLOCK INTERRUPT STATUS REGISTER (BISR) BIT 2 FUNCTION SLIP TYPE DEFAULT DESCRIPTION-OPERATION RO 0 Slip Buffer Block Interrupt Status This bit indicates whether or not the Slip Buffer block has any outstanding interrupt request awaiting service. 0 = Indicates no outstanding Slip Buffer Block interrupt request is awaiting service 1 = Indicates Slip Buffer block has an interrupt request awaiting service. Interrupt Service routine should branch to the interrupt source and read the Slip Buffer Interrupt Status register (address 0xNB08) to clear the interrupt NOTE: 1 ALARM RO 0 T1 FRAME RO 0 This bit will be reset to 0 after the microprocessor has performed a read to the Slip Buffer Interrupt Status Register. Alarm & Error Block Interrupt Status This bit indicates whether or not the Alarm & Error Block has any outstanding interrupt request awaiting service. 0 = Indicates no outstanding interrupt request is awaiting service 1 = Indicates the Alarm & Error Block has an interrupt request awaiting service. Interrupt service routine should branch to the interrupt source and read the corresponding alarm and error status registers (address 0xNB02, 0xNB0E, 0xNB40) to clear the interrupt. NOTE: 0 HEX ADDRESS: 0XNB00 This bit will be reset to 0 after the microprocessor has performed a read to the corresponding Alarm & Error Interrupt Status register that generated the interrupt. T1 Framer Block Interrupt Status This bit indicates whether or not the T1 Framer block has any outstanding interrupt request awaiting service. 0 = Indicates no outstanding interrupt request is awaiting service. 1 = Indicates the T1 Framer Block has an interrupt request awaiting service. Interrupt service routine should branch to the interrupt source and read the T1 Framer status register (address 0xNB04) to clear the interrupt NOTE: This bit will be reset to 0 after the microprocessor has performed a read to the T1 Framer Interrupt Status register. 114 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 114: BLOCK INTERRUPT ENABLE REGISTER (BIER) BIT FUNCTION TYPE DEFAULT REV. 1.0.1 HEX ADDRESS: 0XNB01 DESCRIPTION-OPERATION 7 Reserved For E1 mode only 6 LBCODE_ENB R/W 0 Loopback Code Block interrupt enable This bit permits the user to either enable or disable the Loopback Code Interrupt Block for interrupt generation. Writing a “0” to this register bit will disable the Loopback Code Block for interrupt generation, all Loopback Code interrupts will be disabled for interrupt generation. If the user writes a “1” to this register bit, the Loopback Code Interrupts at the “Block Level” will be enabled. However, the individual Loopback Code interrupts at the “Source Level” still need to be enabled to in order to generate that particular interrupt to the interrupt pin. 0 - Disables all Loopback Code Interrupt Block interrupt within the device. 1 - Enables the Loopback Code interrupt at the “Block-Level”. 5 RXCLKLOSS R/W 0 Loss of Recovered Clock Interrupt Enable This bit permits the user to either enable or disable the Loss of Recovered Clock Interrupt for interrupt generation. 0 - Disables the Loss of Recovered Clock Interrupt within the device. 1 - Enables the Loss of Recovered Clock interrupt at the “SourceLevel”. 4 ONESEC_ENB R/W 0 One Second Interrupt Enable This bit permits the user to either enable or disable the One Second Interrupt for interrupt generation. 0 - Disables the One Second Interrupt within the device. 1 - Enables the One Second interrupt at the “Source-Level”. 3 HDLC_ENB R/W 0 HDLC Block Interrupt Enable This bit permits the user to either enable or disable the HDLC Block for interrupt generation. Writing a “0” to this register bit will disable the HDLC Block for interrupt generation, all HDLC interrupts will be disabled for interrupt generation. If the user writes a “1” to this register bit, the HDLC Block interrupt at the “Block Level” will be enabled. However, the individual HDLC interrupts at the “Source Level” still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - Disables all SA6 Block interrupt within the device. 1 - Enables the SA6 interrupt at the “Block-Level”. 115 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 114: BLOCK INTERRUPT ENABLE REGISTER (BIER) BIT FUNCTION HEX ADDRESS: 0XNB01 TYPE DEFAULT DESCRIPTION-OPERATION 2 SLIP_ENB R/W 0 Slip Buffer Block Interrupt Enable This bit permits the user to either enable or disable the Slip Buffer Block for interrupt generation. Writing a “0” to this register bit will disable the Slip Buffer Block for interrupt generation, then all Slip Buffer interrupts will be disabled for interrupt generation. If the user writes a “1” to this register bit, the Slip Buffer Block interrupt at the “Block Level” will be enabled. However, the individual Slip Buffer interrupts at the “Source Level” still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - Disables all Slip Buffer Block interrupt within the device. 1 - Enables the Slip Buffer interrupt at the “Block-Level”. 1 ALARM_ENB R/W 0 Alarm & Error Block Interrupt Enable This bit permits the user to either enable or disable the Alarm & Error Block for interrupt generation. Writing a “0” to this register bit will disable the Alarm & Error Block for interrupt generation, then all Alarm & Error interrupts will be disabled for interrupt generation. If the user writes a “1” to this register bit, the Alarm & Error Block interrupt at the “Block Level” will be enabled. However, the individual Alarm & Error interrupts at the “Source Level” still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - Disables all Alarm & Error Block interrupt within the device. 1 - Enables the Alarm & Error interrupt at the “Block-Level”. 0 T1FRAME_ENB R/W 0 T1 Framer Block Enable This bit permits the user to either enable or disable the T1 Framer Block for interrupt generation. Writing a “0” to this register bit will disable the T1 Framer Block for interrupt generation, then all T1 Framer interrupts will be disabled for interrupt generation. If the user writes a “1” to this register bit, the T1 Framer Block interrupt at the “Block Level” will be enabled. However, the individual T1 Framer interrupts at the “Source Level” still need to be enabled in order to generate that particular interrupt to the interrupt pin. 0 - Disables all T1 Framer Block interrupt within the device. 1 - Enables the T1 Framer interrupt at the “Block-Level”. 116 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 115: ALARM & ERROR INTERRUPT STATUS REGISTER (AEISR) BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION REV. 1.0.1 HEX ADDRESS: 0XNB02 7 Rx OOF State RO 0 Receive Out of Frame Defect State This READ-ONLY bit indicates whether or not the Receive T1 Framer block is currently declaring the “Out of Frame” defect condition within the incoming T1 data-stream, as described below. Out of Frame defect condition is declared when “TOLR” out of “RANG” errors in the framing bit pattern is detected. (Register 0xN10B) 0 – The Receive T1 Framer block is NOT currently declaring the “Out of Frame” defect condition. 1 – The Receive T1 Framer block is currently declaring the “Out of Frame” defect condition. 6 RxAIS State RO 0 Receive Alarm Indication Status Defect State This READ-ONLY bit indicates whether or not the Receive T1 Framer block is currently declaring the AIS defect condition within the incoming T1 data-stream, as described below. AIS defect is declared when AIS condition persists for 42 milliseconds. AIS defect is cleared when AIS condition is absent for 42 milliseconds. 0 – The Receive T1 Framer block is NOT currently declaring the AIS defect condition. 1 – The Receive T1 Framer block is currently declaring the AIS defect condition. 5 RxYEL State RO 0 Receive Yellow Alarm State This READ-ONLY bit indicates whether or not the Receive T1 Framer block is currently declaring the Yellow Alarm condition within the incoming T1 datastream, as described below. Yellow alarm or Remote Alarm Indication (RAI) is declared when RAI condition persists for 900 milliseconds. Yellow alarm or RAI is cleared immediately when RAI condition is absent even if the T1 Framer is receiving T1 Idle or RAI-CI signatures in ESF mode. 0 – The Receive T1 Framer block is NOT currently declaring the Yellow Alarm condition. 1 – The Receive T1 Framer block is currently declaring the Yellow Alarm condition. 4 LOS_State RO 0 Framer Receive Loss of Signal (LOS) State This READ-ONLY bit indicates whether or not the Receive T1 framer is currently declaring the Loss of Signal (LOS) condition within the incoming T1 data-stream, as described below LOS defect is declared when LOS condition persists for 175 consecutive bits. LOS defect is cleared when LOS condition is absent or when the received signal reaches a 12.5% ones density for 175 consecutive bits. 0 = The Receive T1 Framer block is NOT currently declaring the Loss of Signal (LOS) condition. 1 = The Receive T1 Framer block is currently declaring the Loss of Signal (LOS) condition. 3 LCV Int Status RUR/ WC 0 Line Code Violation Interrupt Status. This Reset-Upon-Read bit field indicates whether or not the Receive T1 LIU block has detected a Line Code Violation interrupt since the last read of this register. 0 = Indicates no Line Code Violation have occurred since the last read of this register. 1 = Indicates one or more Line Code Violation interrupt has occurred since the last read of this register. 117 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 115: ALARM & ERROR INTERRUPT STATUS REGISTER (AEISR) BIT 2 FUNCTION Rx OOF State Change HEX ADDRESS: 0XNB02 TYPE DEFAULT DESCRIPTION-OPERATION RUR/ WC 0 Change in Receive Out of Frame Defect Condition Interrupt Status. This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Out of Frame Defect Condition” interrupt has occurred since the last read of this register. Out of Frame defect condition is declared when “TOLR” out of “RANG” errors in the framing bit pattern is detected. (Register 0xN10B) If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block declares the Out of Frame defect condition. 2. Whenever the Receive T1 Framer block clears the Out of Frame defect condition 0 = Indicates that the “Change in Receive Out of Frame defect condition” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Out of Frame defect condition” interrupt has occurred since the last read of this register 1 RxAIS State Change RUR/ WC 0 Change in Receive AIS Condition Interrupt Status. This Reset-Upon-Read bit field indicates whether or not the “Change in Receive AIS Condition” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block declares the AIS condition. 2. Whenever the Receive T1 Framer block clears the AIS condition 0 = Indicates that the “Change in Receive AIS condition” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive AIS condition” interrupt has occurred since the last read of this register 0 RxYEL State Change RUR/ WC 0 Change in Receive Yellow Alarm Interrupt Status. This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Yellow Alarm Condition” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block declares the Yellow Alarm condition. 2. Whenever the Receive T1 Framer block clears the Yellow Alarm condition 0 = Indicates that the “Change in Receive Yellow Alarm condition” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Yellow Alarm condition” interrupt has occurred since the last read of this register 118 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 116: ALARM & ERROR INTERRUPT ENABLE REGISTER (AEIER) BIT FUNCTION 7-5 Reserved REV. 1.0.1 HEX ADDRESS: 0XNB03 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (E1 mode only) - - This bit should be set to’0’ for proper operation. 4 - 3 LCV ENB R/W 0 Line Code violation interrupt enable This bit permits the user to either enable or disable the “Line Code Violation” interrupt within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when Line Code Violation is detected. 0 = Disables the interrupt generation when Line Code Violation is detected. 1 = Enables the interrupt generation when Line Code Violation is detected. 2 RxOOF ENB R/W 0 Change in Out of Frame Defect Condition interrupt enable This bit permits the user to either enable or disable the “Change in Out of Frame Defect Condition” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. The instant that the Receive T1 Framer block declares the Out of Frame defect condition. 2. The instant that the Receive T1 Framer block clears the Out of Frame defect condition. 0 – Disables the “Change in Out of Frame Defect Condition” Interrupt. 1 – Enables the “Change in Out of Frame Defect Condition” Interrupt. 1 RxAIS ENB R/W 0 Change in AIS Condition interrupt enable This bit permits the user to either enable or disable the “Change in AIS Condition” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. The instant that the Receive T1 Framer block declares the AIS condition. 2. The instant that the Receive T1 Framer block clears the AIS condition. 0 – Disables the “Change in AIS Condition” Interrupt. 1 – Enables the “Change in AIS Condition” Interrupt. 0 RxYEL ENB R/W 0 Change in Yellow alarm Condition interrupt enable This bit permits the user to either enable or disable the “Change in Yellow Alarm Condition” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. The instant that the Receive T1 Framer block declares the Yellow Alarm condition. 2. The instant that the Receive T1 Framer block clears the Yellow Alarm condition. 0 – Disables the “Change in Yellow Alarm Condition” Interrupt. 1 – Enables the “Change in Yellow Alarm Condition” Interrupt. 119 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 117: FRAMER INTERRUPT STATUS REGISTER (FISR) BIT 7 FUNCTION DS0_Change HEX ADDRESS: 0XNB04 TYPE DEFAULT DESCRIPTION-OPERATION RUR 0 Change in DS-0 Yellow Alarm Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in DS-0 Yellow Alarm” interrupt has occurred since the last read of this register. 0 - Indicates that the “Change in DS-0 Yellow Alarm” interrupt has not occurred since the last read of this register. 1 - Indicates that the “Change in DS-0 Yellow Alarm” interrupt has occurred since the last read of this register. NOTE: By default, DS-0 Yellow Alarm is detected on the Ingress (RTip/ RRing) side. To detect DS-0 YEL on the Egress (TxSER) side, the DS-0 Switch bit (bit 2) must be set to "1" in register 0xN112. 6 DS0_Status RO 0 DS-0 Yellow Alarm Interrupt Status This Read Only bit will indicate the state of the DS-0 Yellow Alarm detection. When a DS-0 Yellow alarm is present, this bit will be pulled "High". When a DS-0 Yellow Alarm is not present, this bit will remain "Low". 0 - DS-0 Yellow Alarm is not Detected 1 - DS-0 Yellow Alarm is Detected NOTE: By default, DS-0 Yellow Alarm is detected on the Ingress (RTip/ RRing) side. To detect DS-0 YEL on the Egress (TxSER) side, the DS-0 Switch bit (bit 2) must be set to "1" in register 0xN112. 5 SIG RUR/ WC 0 Change in Signaling Bits Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Signaling Bits” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt whenever any one of the four signaling bits values (A,B,C,D) has changed in any one of the 24 channels within the incoming T1 frames. Users can read the signaling change registers (address 0xN10D0xN10F) to determine which signalling channel has changed. 0 = Indicates that the “Change in Signaling Bits” interrupt has not occurred since the last read of this register. 1 = Indicates that the “Change in Signaling Bits” interrupt has occurred since the last read of this register. NOTE: This bit only has meaning when Robbed-Bit Signaling is enabled. 4 COFA RUR/ WC 0 Change of Frame Alignment (COFA) Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change of Framing Alignment (COFA)” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt whenever the Receive T1 Framer block detects a Change of Framing Alignment Signal (e.g., the Framing bits have appeared to move to a different location within the incoming T1 data stream). 0 = Indicates that the “Change of Framing Alignment (COFA)” interrupt has not occurred since the last read of this register. 1 = Indicates that the “Change of Framing Alignment (COFA)” interrupt has occurred since the last read of this register. 120 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 117: FRAMER INTERRUPT STATUS REGISTER (FISR) BIT 3 FUNCTION OOF_Status REV. 1.0.1 HEX ADDRESS: 0XNB04 TYPE DEFAULT DESCRIPTION-OPERATION RUR/ WC 0 Change in Receive Out of Frame Defect Condition Interrupt Status. This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Out of Frame Defect Condition” interrupt has occurred since the last read of this register. Out of Frame defect condition is declared when “TOLR” out of “RANG” errors in the framing bit pattern is detected. (Register 0xN10B) If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block declares the Out of Frame defect condition. 2. Whenever the Receive T1 Framer block clears the Out of Frame defect condition 0 = Indicates that the “Change in Receive Out of Frame defect condition” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Out of Frame defect condition” interrupt has occurred since the last read of this register 2 FMD RUR/ WC 0 Frame Mimic Detection Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Frame Mimic Detection” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt whenever the Receive T1 Framer block detects the presence of Frame Mimic bits (i.e., the Payload bits have appeared to mimic the Framing Bit pattern within the incoming T1 data stream). 0 = Indicates that the “Frame Mimic Detection” interrupt has not occurred since the last read of this register. 1 = Indicates that the “Frame Mimic Detection” interrupt has occurred since the last read of this register. 1 SE RUR/ WC 0 Synchronization Bit Error (CRC-6) Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “CRC-6 Error” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt whenever the Receive T1 Framer block detects a CRC-6 Error within the incoming T1 multiframe. 0 = Indicates that the “CRC-6 Error” interrupt has not occurred since the last read of this register. 1 = Indicates that the “CRC-6 Error” interrupt has occurred since the last read of this register. 0 FE RUR/ WC 0 Framing Error Interrupt Status This Reset-Upon-Read bit field indicates whether or not a “Framing Error” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt whenever the Receive T1 Framer block detects one or more Framing Alignment Bit Error within the incoming T1 data stream. 0 = Indicates that the “Framing Error” interrupt has not occurred since the last read of this register. 1 = Indicates that the “Framing Error” interrupt has occurred since the last read of this register. NOTE: This bit doesn't not necessarily indicate that synchronization has been lost. 121 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 118: FRAMER INTERRUPT ENABLE REGISTER (FIER) BIT 7 FUNCTION DS0 ENB HEX ADDRESS: 0XNB05 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 DS-0 Yellow Alarm This bit is used to enable or disable the DS-0 Yellow Alarm interrupt within the framer block. This yellow alarm is independent of the framing format selected. Any time a DS-0 Yellow Alarm occurs (bit 2 = 0 in each DS-0 time slot), bit 7 and bit 6 in register 0xNB04 will report the status. 0 - Disables the interrupt generation 1 - Enables the interrupt generation NOTE: By default, DS-0 Yellow Alarm is detected on the Ingress (RTip/ RRing) side. To detect DS-0 YEL on the Egress (TxSER) side, the DS-0 Switch bit (bit 2) must be set to "1" in register 0xN112. 6 Reserved - - Reserved 5 SIG_ENB R/W 0 Change in Signaling Bits Interrupt Enable This bit permits the user to either enable or disable the “Change in Signaling Bits” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when it detects a change in the any four signaling bits (A,B,C,D) in any one of the 24 signaling channels. Users can read the signaling change registers (address 0xN10D-0xN10F) to determine which signalling channel has changed state. 0 - Disables the Change in Signaling Bits Interrupt 1 - Enables the Change in Signaling Bits Interrupt NOTE: This bit has no meaning when Robbed-Bit Signaling is disabled. 4 COFA_ENB R/W 0 Change of Framing Alignment (COFA) Interrupt Enable This bit permits the user to either enable or disable the “Change in FAS Framing Alignment (COFA)” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when it detects a Change of Framing Alignment Signal (e.g., the Framing bits have appeared to move to a different location within the incoming T1 data stream). 0 - Disables the “Change of Framing Alignment (COFA)” Interrupt. 1 - Enables the “Change of Framing Alignment (COFA)” Interrupt. 3 OOF_ENB R/W 0 Change in Out of Frame Defect Condition interrupt enable This bit permits the user to either enable or disable the “Change in Out of Frame Defect Condition” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. The instant that the Receive T1 Framer block declares the Out of Frame defect condition. 2. The instant that the Receive T1 Framer block clears the Out of Frame defect condition. 0 – Disables the “Change in Out of Frame Defect Condition” Interrupt. 1 – Enables the “Change in Out of Frame Defect Condition” Interrupt. 122 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 118: FRAMER INTERRUPT ENABLE REGISTER (FIER) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XNB05 TYPE DEFAULT DESCRIPTION-OPERATION 2 FMD_ENB R/W 0 Frame Mimic Detection Interrupt Enable This bit permits the user to either enable or disable the “Frame Mimic Detection” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when it detects the presence of Frame mimic bits (i.e., the payload bits have appeared to mimic the framing bit pattern within the incoming T1 data stream). 0 - Disables the “Frame Mimic Detection” Interrupt. 1 - Enables the “Frame Mimic Detection” Interrupt. 1 SE_ENB R/W 0 Synchronization Bit (CRC-6) Error Interrupt Enable This bit permits the user to either enable or disable the “CRC-6 Error Detection” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when it detects a CRC-6 error within the incoming T1 multiframe. 0 - Disables the “CRC-6 Error Detection” Interrupt. 1 - Enables the “CRC-6 Error Detection” Interrupt. 0 FE_ENB R/W 0 Framing Bit Error Interrupt Enable This bit permits the user to either enable or disable the “Framing Alignment Bit Error Detection” Interrupt, within the XRT86VX38 device. If the user enables this interrupt, then the Receive T1 Framer block will generate an interrupt when it detects one or more Framing Alignment Bit error within the incoming T1 data stream. 0 - Disables the “Framing Alignment Bit Error Detection” Interrupt. 1 - Enables the “Framing Alignment Bit Error Detection” Interrupt. NOTE: Detecting Framing Alignment Bit Error doesn't not necessarily indicate that synchronization has been lost. 123 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 119: DATA LINK STATUS REGISTER 1 (DLSR1) BIT FUNCTION HEX ADDRESS: 0XNB06 TYPE DEFAULT DESCRIPTION-OPERATION RO 0 HDLC1 Message Type Identifier This READ ONLY bit indicates the type of data link message received by Receive HDLC 1 Controller. Two types of data link messages are supported within the XRT86VX38 device: Message Oriented Signaling (MOS) or Bit-Oriented Signalling (BOS). 0 = Indicates Bit-Oriented Signaling (BOS) type data link message is received 1 = Indicates Message Oriented Signaling (MOS) type data link message is received 7 MSG TYPE 6 TxSOT RUR/ WC 0 Transmit HDLC1 Controller Start of Transmission (TxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the “Transmit HDLC1 Controller Start of Transmission (TxSOT) “Interrupt has occurred since the last read of this register. Transmit HDLC1 Controller will declare this interrupt when it has started to transmit a data link message. For sending large HDLC messages, start loading the next available buffer once this interrupt is detected. 0 = Transmit HDLC1 Controller Start of Transmission (TxSOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC1 Controller Start of Transmission interrupt (TxSOT) has occurred since the last read of this register. 5 RxSOT RUR/ WC 0 Receive HDLC1 Controller Start of Reception (RxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC1 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register. Receive HDLC1 Controller will declare this interrupt when it has started to receive a data link message. 0 = Receive HDLC1 Controller Start of Reception (RxSOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC1 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register 4 TxEOT RUR/ WC 0 Transmit HDLC1 Controller End of Transmission (TxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit HDLC1 Controller End of Transmission (TxEOT) Interrupt has occurred since the last read of this register. Transmit HDLC1 Controller will declare this interrupt when it has completed its transmission of a data link message. For sending large HDLC messages, it is critical to load the next available buffer before this interrupt occurs. 0 = Transmit HDLC1 Controller End of Transmission (TxEOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC1 Controller End of Transmission (TxEOT) interrupt has occurred since the last read of this register 124 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 119: DATA LINK STATUS REGISTER 1 (DLSR1) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XNB06 TYPE DEFAULT DESCRIPTION-OPERATION 3 RxEOT RUR/ WC 0 Receive HDLC1 Controller End of Reception (RxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC1 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register. Receive HDLC1 Controller will declare this interrupt once it has completely received a full data link message, or once the buffer is full. 0 = Receive HDLC1 Controller End of Reception (RxEOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC1 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register 2 FCS Error RUR/ WC 0 FCS Error Interrupt Status This Reset-Upon-Read bit indicates whether or not the FCS Error Interrupt has occurred since the last read of this register. Receive HDLC1 Controller will declare this interrupt when it has detected the FCS error in the most recently received data link message. 0 = FCS Error interrupt has not occurred since the last read of this register 1 = FCS Error interrupt has occurred since the last read of this register 1 Rx ABORT RUR/ WC 0 Receipt of Abort Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Abort Sequence interrupt has occurred since last read of this register. Receive HDLC1 Controller will declare this interrupt if it detects the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) in the incoming data link channel. 0 = Receipt of Abort Sequence interrupt has not occurred since last read of this register 1 = Receipt of Abort Sequence interrupt has occurred since last read of this register 0 RxIDLE RUR/ WC 0 Receipt of Idle Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Idle Sequence interrupt has occurred since the last read of this register. The Receive HDLC1 Controller will declare this interrupt if it detects the flag sequence octet (0x7E) in the incoming data link channel. If RxIDLE "AND" RxEOT occur together, then the entire HDLC message has been received. 0 = Receipt of Idle Sequence interrupt has not occurred since last read of this register 1 = Receipt of Idle Sequence interrupt has occurred since last read of this register. 125 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 120: DATA LINK INTERRUPT ENABLE REGISTER 1 (DLIER1) BIT FUNCTION TYPE DEFAULT - - Reserved HEX ADDRESS: 0XNB07 DESCRIPTION-OPERATION 7 Reserved 6 TxSOT ENB R/W 0 Transmit HDLC1 Controller Start of Transmission (TxSOT) Interrupt Enable This bit enables or disables the “Transmit HDLC1 Controller Start of Transmission (TxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC1 Controller will generate an interrupt when it has started to transmit a data link message. 0 = Disables the Transmit HDLC1 Controller Start of Transmission (TxSOT) interrupt. 1 = Enables the Transmit HDLC1 Controller Start of Transmission (TxSOT) interrupt. 5 RxSOT ENB R/W 0 Receive HDLC1 Controller Start of Reception (RxSOT) Interrupt Enable This bit enables or disables the “Receive HDLC1 Controller Start of Reception (RxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC1 Controller will generate an interrupt when it has started to receive a data link message. 0 = Disables the Receive HDLC1 Controller Start of Reception (RxSOT) interrupt. 1 = Enables the Receive HDLC1 Controller Start of Reception (RxSOT) interrupt. 4 TxEOT ENB R/W 0 Transmit HDLC1 Controller End of Transmission (TxEOT) Interrupt Enable This bit enables or disables the “Transmit HDLC1 Controller End of Transmission (TxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC1 Controller will generate an interrupt when it has finished transmitting a data link message. 0 = Disables the Transmit HDLC1 Controller End of Transmission (TxEOT) interrupt. 1 = Enables the Transmit HDLC1 Controller End of Transmission (TxEOT) interrupt. 3 RxEOT ENB R/W 0 Receive HDLC1 Controller End of Reception (RxEOT) Interrupt Enable This bit enables or disables the “Receive HDLC1 Controller End of Reception (RxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC1 Controller will generate an interrupt when it has finished receiving a complete data link message. 0 = Disables the Receive HDLC1 Controller End of Reception (RxEOT) interrupt. 1 = Enables the Receive HDLC1 Controller End of Reception (RxEOT) interrupt. 126 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 120: DATA LINK INTERRUPT ENABLE REGISTER 1 (DLIER1) BIT FUNCTION TYPE DEFAULT REV. 1.0.1 HEX ADDRESS: 0XNB07 DESCRIPTION-OPERATION 2 FCS ERR ENB R/W 0 FCS Error Interrupt Enable This bit enables or disables the “Received FCS Error “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC1 Controller will generate an interrupt when it has detected the FCS error within the incoming data link message. 0 = Disables the “Receive FCS Error” interrupt. 1 = Enables the “Receive FCS Error” interrupt. 1 RxABORT ENB R/W 0 Receipt of Abort Sequence Interrupt Enable This bit enables or disables the “Receipt of Abort Sequence“ Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC1 Controller will generate an interrupt when it has detected the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) within the incoming data link channel. 0 = Disables the “Receipt of Abort Sequence” interrupt. 1 = Enables the “Receipt of Abort Sequence” interrupt. 0 RxIDLE ENB R/W 0 Receipt of Idle Sequence Interrupt Enable This bit enables or disables the “Receipt of Idle Sequence“ Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC1 Controller will generate an interrupt when it has detected the Idle Sequence Octet (i.e. 0x7E) within the incoming data link channel. 0 = Disables the “Receipt of Idle Sequence” interrupt. 1 = Enables the “Receipt of Idle Sequence” interrupt. 127 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 121: SLIP BUFFER INTERRUPT STATUS REGISTER (SBISR) BIT FUNCTION HEX ADDRESS: 0XNB08 TYPE DEFAULT DESCRIPTION-OPERATION 7 TxSB_FULL RUR/ WC 0 Transmit Slip buffer Full Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit Slip Buffer Full interrupt has occurred since the last read of this register. The transmit Slip Buffer Full interrupt is declared when the transmit slip buffer is filled. If the transmit slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Transmit Slip Buffer Full interrupt has not occurred since the last read of this register. 1 = Indicates that the Transmit Slip Buffer Full interrupt has occurred since the last read of this register. 6 TxSB_EMPT RUR/ WC 0 Transmit Slip buffer Empty Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit Slip Buffer Empty interrupt has occurred since the last read of this register. The transmit Slip Buffer Empty interrupt is declared when the transmit slip buffer is emptied. If the transmit slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Transmit Slip Buffer Empty interrupt has not occurred since the last read of this register. 1 = Indicates that the Transmit Slip Buffer Empty interrupt has occurred since the last read of this register. 5 TxSB_SLIP RUR/ WC 0 Transmit Slip Buffer Slips Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit Slip Buffer Slips interrupt has occurred since the last read of this register. The transmit Slip Buffer Slips interrupt is declared when the transmit slip buffer is either filled or emptied. This interrupt bit will be set to ‘1’ in either one of these two conditions: 1. If the transmit slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 2. If the transmit slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Transmit Slip Buffer Slips interrupt has not occurred since the last read of this register. 1 = Indicates that the Transmit Slip Buffer Slips interrupt has occurred since the last read of this register. NOTE: Users still need to read the Transmit Slip Buffer Empty Interrupt (bit 6 of this register) or the Transmit Slip Buffer Full Interrupts (bit 7 of this register) to determine whether transmit slip buffer empties or fills. 128 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 121: SLIP BUFFER INTERRUPT STATUS REGISTER (SBISR) BIT 4 FUNCTION SLC®96 LOCK REV. 1.0.1 HEX ADDRESS: 0XNB08 TYPE DEFAULT DESCRIPTION-OPERATION RO 0 SLC®96 is in SYNC This READ ONLY bit field indicates whether or not frame synchronization is achieved when the XRT86VX38 is configured in SLC®96 framing mode. 0 = Indicates that frame synchronization is not achieved in SLC®96 framing mode. 1 = Indicates that frame synchronization is achieved in SLC®96 framing mode. 3 Multiframe LOCK 2 RxSB_FULL RO 0 Multiframe is in SYNC This READ ONLY bit field indicates whether or not the T1 Receive Framer Block is declaring T1 Multiframe LOCK status. 0 = Indicates that the T1 Receive Framer is currently declaring T1 multiframe LOSS OF LOCK status 0 = Indicates that the T1 Receive Framer is currently declaring T1 multiframe LOCK status RUR/ WC 0 Receive Slip buffer Full Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive Slip Buffer Full interrupt has occurred since the last read of this register. The Receive Slip Buffer Full interrupt is declared when the receive slip buffer is filled. If the receive slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Receive Slip Buffer Full interrupt has not occurred since the last read of this register. 1 = Indicates that the Receive Slip Buffer Full interrupt has occurred since the last read of this register. 129 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 121: SLIP BUFFER INTERRUPT STATUS REGISTER (SBISR) BIT FUNCTION HEX ADDRESS: 0XNB08 TYPE DEFAULT DESCRIPTION-OPERATION 1 RxSB_EMPT RUR/ WC 0 Receive Slip buffer Empty Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive Slip Buffer Empty interrupt has occurred since the last read of this register. The Receive Slip Buffer Empty interrupt is declared when the receive slip buffer is emptied. If the receive slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Receive Slip Buffer Empty interrupt has not occurred since the last read of this register. 1 = Indicates that the Receive Slip Buffer Empty interrupt has occurred since the last read of this register. 0 RxSB_SLIP RUR/ WC 0 Receive Slip Buffer Slips Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive Slip Buffer Slips interrupt has occurred since the last read of this register. The Receive Slip Buffer Slips interrupt is declared when the receive slip buffer is either filled or emptied. This interrupt bit will be set to ‘1’ in either one of these two conditions: 1. If the receive slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 2. If the receive slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 = Indicates that the Receive Slip Buffer Slips interrupt has not occurred since the last read of this register. 1 = Indicates that the Receive Slip Buffer Slips interrupt has occurred since the last read of this register. NOTE: Users still need to read the Receive Slip Buffer Empty Interrupt (bit 1 of this register) or the Receive Slip Buffer Full Interrupts (bit 2 of this register) to determine whether transmit slip buffer empties or fills. 130 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 122: SLIP BUFFER INTERRUPT ENABLE REGISTER (SBIER) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XNB09 TYPE DEFAULT DESCRIPTION-OPERATION 7 TxFULL_ENB R/W 0 Transmit Slip Buffer Full Interrupt Enable This bit enables or disables the Transmit Slip Buffer Full interrupt within the XRT86VX38 device. Once this interrupt is enabled, the transmit Slip Buffer Full interrupt is declared when the transmit slip buffer is filled. If the transmit slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and the interrupt status bit will be set to ‘1’. 0 - Disables the Transmit Slip Buffer Full interrupt when the Transmit Slip Buffer fills 1 - Enables the Transmit Slip Buffer Full interrupt when the Transmit Slip Buffer fills. 6 TxEMPT_ENB R/W 0 Transmit Slip Buffer Empty Interrupt Enable This bit enables or disables the Transmit Slip Buffer Empty interrupt within the XRT86VX38 device. Once this interrupt is enabled, the transmit Slip Buffer Empty interrupt is declared when the transmit slip buffer is emptied. If the transmit slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ‘1’. 0 - Disables the Transmit Slip Buffer Empty interrupt when the Transmit Slip Buffer empties 1 - Enables the Transmit Slip Buffer Empty interrupt when the Transmit Slip Buffer empties. 5 TxSLIP_ENB R/W 0 Transmit Slip Buffer Slips Interrupt Enable This bit enables or disables the Transmit Slip Buffer Slips interrupt within the XRT86VX38 device. Once this interrupt is enabled, the transmit Slip Buffer Slips interrupt is declared when either the transmit slip buffer is filled or emptied. If the transmit slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ‘1’. The interrupt status bit will be set to ‘1’ in either one of these two conditions: 1. If the transmit slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 2. If the transmit slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 - Disables the Transmit Slip Buffer Slips interrupt when the Transmit Slip Buffer empties or fills 1 - Enables the Transmit Slip Buffer Slips interrupt when the Transmit Slip Buffer empties or fills. 4-3 Reserved - - Reserved 131 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 122: SLIP BUFFER INTERRUPT ENABLE REGISTER (SBIER) BIT FUNCTION HEX ADDRESS: 0XNB09 TYPE DEFAULT DESCRIPTION-OPERATION 2 RxFULL_ENB R/W 0 Receive Slip Buffer Full Interrupt Enable This bit enables or disables the Receive Slip Buffer Full interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive Slip Buffer Full interrupt is declared when the receive slip buffer is filled. If the Receive slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and the interrupt status bit will be set to ‘1’. 0 - Disables the Receive Slip Buffer Full interrupt when the Transmit Slip Buffer fills 1 - Enables the Receive Slip Buffer Full interrupt when the Transmit Slip Buffer fills. 1 RxEMPT_ENB R/W 0 Receive Slip buffer Empty Interrupt Enable This bit enables or disables the Receives Slip Buffer Empty interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive Slip Buffer Empty interrupt is declared when the Receive slip buffer is emptied. If the Receive slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ‘1’. 0 - Disables the Receive Slip Buffer Empty interrupt when the Transmit Slip Buffer empties 1 - Enables the Receive Slip Buffer Empty interrupt when the Transmit Slip Buffer empties. 0 RxSLIP_ENB R/W 0 Receive Slip buffer Slips Interrupt Enable This bit enables or disables the Receive Slip Buffer Slips interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive Slip Buffer Slips interrupt is declared when either the Receive slip buffer is filled or emptied. If the Receive slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and the interrupt status bit will be set to ‘1’. The interrupt status bit will be set to ‘1’ in either one of these two conditions: 1. If the Receive slip buffer is emptied and a READ operation occurs, then a full frame of data will be repeated, and this interrupt bit will be set to ‘1’. 2. If the Receive slip buffer is full and a WRITE operation occurs, then a full frame of data will be deleted, and this interrupt bit will be set to ‘1’. 0 - Disables the Receive Slip Buffer Slips interrupt when the Transmit Slip Buffer empties or fills 1 - Enables the Receive Slip Buffer Slips interrupt when the Transmit Slip Buffer empties or fills. 132 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 123: RECEIVE LOOPBACK CODE 0 INTERRUPT AND STATUS REGISTER (RLCISR0) HEX ADDRESS: 0XNB0A BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR - address 0xN126) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR - address 0xN127) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 133 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 124: RECEIVE LOOPBACK CODE 0 INTERRUPT ENABLE REGISTER (RLCIER0) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB0B TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 134 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 125: EXCESSIVE ZERO STATUS REGISTER (EXZSR) BIT FUNCTION 7-1 Reserved 0 EXZ_STATUS REV. 1.0.1 HEX ADDRESS: 0XNB0E TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved RUR/ WC 0 Change in Excessive Zero Condition Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Excessive Zero Condition” interrupt within the T1 Receive Framer Block has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Excessive Zero Condition. 2. Whenever the Receive T1 Framer block clears the Excessive Zero Condition 0 = Indicates the “Change in Excessive Zero Condition” interrupt has NOT occurred since the last read of this register 1 = Indicates the “Change in Excessive Zero Condition” interrupt has occurred since the last read of this register TABLE 126: EXCESSIVE ZERO ENABLE REGISTER (EXZER) BIT FUNCTION 7-1 0 EXZ_ENB HEX ADDRESS: 0XNB0F TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Change in Excessive Zero Condition Interrupt Enable This bit enables or disables the “Change in Excessive Zero Condition” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Excessive Zero Condition. 2. Whenever the Receive T1 Framer block clears the Excessive Zero Condition 0 - Disables the “Change in Excessive Zero Condition” interrupt within the Receive T1 Framer Block 1 - Enables the “Change in Excessive Zero Condition” interrupt within the Receive T1 Framer Block 135 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 127: SS7 STATUS REGISTER FOR LAPD1 (SS7SR1) BIT 0 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION SS7_1_STATUS RUR/ WC 0 SS7 Interrupt Status for LAPD Controller 1 This Reset-Upon-Read bit field indicates whether or not the “SS7” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 = Indicates that the “SS7” interrupt has not occurred since the last read of this register 1 = Indicates that the “SS7” interrupt has occurred since the last read of this register TABLE 128: SS7 ENABLE REGISTER FOR LAPD1 (SS7ER1) BIT 0 HEX ADDRESS: 0XNB10 FUNCTION SS7_1_ENB TYPE DEFAULT R/W 0 HEX ADDRESS: 0XNB11 DESCRIPTION-OPERATION SS7 Interrupt Enable for LAPD Controller 1 This bit enables or disables the “SS7” interrupt within the LAPD Controller 1. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 - Disables the “SS7” interrupt within the LAPD Controller 1. 1 - Enables the “SS7” interrupt within the LAPD Controller 1. 136 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 129: RXLOS/CRC INTERRUPT STATUS REGISTER (RLCISR) 0XNB12 BIT FUNCTION 7-4 3 RxLOSINT HEX ADDRESS: TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved RUR/ WC 0 Change in Receive LOS condition Interrupt Status This bit indicates whether or not the “Change in Receive LOS condition” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block declares the Receive LOS condition. 2. Whenever the Receive T1 Framer block clears the Receive LOS condition. 0 = Indicates that the “Change in Receive LOS Condition” interrupt has not occurred since the last read of this register. 1 = Indicates that the “Change in Receive LOS Condition” interrupt has occurred since the last read of this register. 2-0 Reserved - - TABLE 130: RXLOS/CRC INTERRUPT ENABLE REGISTER (RLCIER) BIT 3 FUNCTION RxLOS_ENB 2-0 - HEX ADDRESS: 0XNB13 TYPE DEFAULT DESCRIPTION-OPERATION R/W 0 Change in Receive LOS Condition Interrupt Enable This bit enables the “Change in Receive LOS Condition” interrupt. 0 = Enables “Change in Receive LOS Condition” Interrupt. 1 = Disables “Change in Receive LOS Condition” Interrupt. - - Reserved 137 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 131: RECEIVE LOOPBACK CODE 1 INTERRUPT AND STATUS REGISTER (RLCISR1) HEX ADDRESS: 0XNB14 BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 138 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 132: RECEIVE LOOPBACK CODE 1 INTERRUPT ENABLE REGISTER (RLCIER1) BIT FUNCTION 7-2 Reserved 1 RXAENB REV. 1.0.1 HEX ADDRESS: 0XNB15 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 139 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 133: DATA LINK STATUS REGISTER 2 (DLSR2) BIT FUNCTION HEX ADDRESS: 0XNB16 TYPE DEFAULT DESCRIPTION-OPERATION RO 0 HDLC2 Message Type Identifier This READ ONLY bit indicates the type of data link message received by Receive HDLC 2 Controller. Two types of data link messages are supported within the XRT86VX38 device: Message Oriented Signaling (MOS) or Bit-Oriented Signalling (BOS). 0 = Indicates Bit-Oriented Signaling (BOS) type data link message is received 1 = Indicates Message Oriented Signaling (MOS) type data link message is received 7 MSG TYPE 6 TxSOT RUR/ WC 0 Transmit HDLC2 Controller Start of Transmission (TxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the “Transmit HDLC2 Controller Start of Transmission (TxSOT) “Interrupt has occurred since the last read of this register. Transmit HDLC2 Controller will declare this interrupt when it has started to transmit a data link message. For sending large HDLC messages, start loading the next available buffer once this interrupt is detected. 0 = Transmit HDLC2 Controller Start of Transmission (TxSOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC2 Controller Start of Transmission interrupt (TxSOT) has occurred since the last read of this register. 5 RxSOT RUR/ WC 0 Receive HDLC2 Controller Start of Reception (RxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC2 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register. Receive HDLC2 Controller will declare this interrupt when it has started to receive a data link message. 0 = Receive HDLC2 Controller Start of Reception (RxSOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC2 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register 4 TxEOT RUR/ WC 0 Transmit HDLC2 Controller End of Transmission (TxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit HDLC2 Controller End of Transmission (TxEOT) Interrupt has occurred since the last read of this register. Transmit HDLC2 Controller will declare this interrupt when it has completed its transmission of a data link message. For sending large HDLC messages, it is critical to load the next available buffer before this interrupt occurs. 0 = Transmit HDLC2 Controller End of Transmission (TxEOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC2 Controller End of Transmission (TxEOT) interrupt has occurred since the last read of this register 140 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 133: DATA LINK STATUS REGISTER 2 (DLSR2) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XNB16 TYPE DEFAULT DESCRIPTION-OPERATION 3 RxEOT RUR/ WC 0 Receive HDLC2 Controller End of Reception (RxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC2 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register. Receive HDLC2 Controller will declare this interrupt once it has completely received a full data link message, or once the buffer is full. 0 = Receive HDLC2 Controller End of Reception (RxEOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC2 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register 2 FCS Error RUR/ WC 0 FCS Error Interrupt Status This Reset-Upon-Read bit indicates whether or not the FCS Error Interrupt has occurred since the last read of this register. Receive HDLC2 Controller will declare this interrupt when it has detected the FCS error in the most recently received data link message. 0 = FCS Error interrupt has not occurred since the last read of this register 1 = FCS Error interrupt has occurred since the last read of this register 1 Rx ABORT RUR/ WC 0 Receipt of Abort Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Abort Sequence interrupt has occurred since last read of this register. Receive HDLC2 Controller will declare this interrupt if it detects the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) in the incoming data link channel. 0 = Receipt of Abort Sequence interrupt has not occurred since last read of this register 1 = Receipt of Abort Sequence interrupt has occurred since last read of this register 0 RxIDLE RUR/ WC 0 Receipt of Idle Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Idle Sequence interrupt has occurred since the last read of this register. The Receive HDLC2 Controller will declare this interrupt if it detects the flag sequence octet (0x7E) in the incoming data link channel. If RxIDLE "AND" RxEOT occur together, then the entire HDLC message has been received. 0 = Receipt of Idle Sequence interrupt has not occurred since last read of this register 1 = Receipt of Idle Sequence interrupt has occurred since last read of this register. 141 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 134: DATA LINK INTERRUPT ENABLE REGISTER 2 (DLIER2) BIT FUNCTION TYPE DEFAULT - - Reserved HEX ADDRESS: 0XNB17 DESCRIPTION-OPERATION 7 Reserved 6 TxSOT ENB R/W 0 Transmit HDLC2 Controller Start of Transmission (TxSOT) Interrupt Enable This bit enables or disables the “Transmit HDLC2 Controller Start of Transmission (TxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC2 Controller will generate an interrupt when it has started to transmit a data link message. 0 = Disables the Transmit HDLC2 Controller Start of Transmission (TxSOT) interrupt. 1 = Enables the Transmit HDLC2 Controller Start of Transmission (TxSOT) interrupt. 5 RxSOT ENB R/W 0 Receive HDLC2 Controller Start of Reception (RxSOT) Interrupt Enable This bit enables or disables the “Receive HDLC2 Controller Start of Reception (RxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC2 Controller will generate an interrupt when it has started to receive a data link message. 0 = Disables the Receive HDLC2 Controller Start of Reception (RxSOT) interrupt. 1 = Enables the Receive HDLC2 Controller Start of Reception (RxSOT) interrupt. 4 TxEOT ENB R/W 0 Transmit HDLC2 Controller End of Transmission (TxEOT) Interrupt Enable This bit enables or disables the “Transmit HDLC2 Controller End of Transmission (TxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC2 Controller will generate an interrupt when it has finished transmitting a data link message. 0 = Disables the Transmit HDLC2 Controller End of Transmission (TxEOT) interrupt. 1 = Enables the Transmit HDLC2 Controller End of Transmission (TxEOT) interrupt. 3 RxEOT ENB R/W 0 Receive HDLC2 Controller End of Reception (RxEOT) Interrupt Enable This bit enables or disables the “Receive HDLC2 Controller End of Reception (RxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC2 Controller will generate an interrupt when it has finished receiving a complete data link message. 0 = Disables the Receive HDLC2 Controller End of Reception (RxEOT) interrupt. 1 = Enables the Receive HDLC2 Controller End of Reception (RxEOT) interrupt. 142 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 134: DATA LINK INTERRUPT ENABLE REGISTER 2 (DLIER2) BIT FUNCTION TYPE DEFAULT REV. 1.0.1 HEX ADDRESS: 0XNB17 DESCRIPTION-OPERATION 2 FCS ERR ENB R/W 0 FCS Error Interrupt Enable This bit enables or disables the “Received FCS Error “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC2 Controller will generate an interrupt when it has detected the FCS error within the incoming data link message. 0 = Disables the “Receive FCS Error” interrupt. 1 = Enables the “Receive FCS Error” interrupt. 1 RxABORT ENB R/W 0 Receipt of Abort Sequence Interrupt Enable This bit enables or disables the “Receipt of Abort Sequence“Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC2 Controller will generate an interrupt when it has detected the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) within the incoming data link channel. 0 = Disables the “Receipt of Abort Sequence” interrupt. 1 = Enables the “Receipt of Abort Sequence” interrupt. 0 RxIDLE ENB R/W 0 Receipt of Idle Sequence Interrupt Enable This bit enables or disables the “Receipt of Idle Sequence“Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC2 Controller will generate an interrupt when it has detected the Idle Sequence Octet (i.e. 0x7E) within the incoming data link channel. 0 = Disables the “Receipt of Idle Sequence” interrupt. 1 = Enables the “Receipt of Idle Sequence” interrupt. 143 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 135: SS7 STATUS REGISTER FOR LAPD2 (SS7SR2) BIT 0 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION SS7_2_STATUS RUR/ WC 0 SS7 Interrupt Status for LAPD Controller 2 This Reset-Upon-Read bit field indicates whether or not the “SS7” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 = Indicates that the “SS7” interrupt has not occurred since the last read of this register 1 = Indicates that the “SS7” interrupt has occurred since the last read of this register TABLE 136: SS7 ENABLE REGISTER FOR LAPD2 (SS7ER2) BIT 0 HEX ADDRESS: 0XNB18 FUNCTION SS7_2_ENB TYPE DEFAULT R/W 0 HEX ADDRESS: 0XNB19 DESCRIPTION-OPERATION SS7 Interrupt Enable for LAPD Controller 2 This bit enables or disables the “SS7” interrupt within the LAPD Controller 2. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 - Disables the “SS7” interrupt within the LAPD Controller 2. 1 - Enables the “SS7” interrupt within the LAPD Controller 2. 144 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 137: RECEIVE LOOPBACK CODE 2 INTERRUPT AND STATUS REGISTER (RLCISR2) HEX ADDRESS: 0XNB1A BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 145 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 138: RECEIVE LOOPBACK CODE 2 INTERRUPT ENABLE REGISTER (RLCIER2) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB1B TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 146 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 139: RECEIVE LOOPBACK CODE 3 INTERRUPT AND STATUS REGISTER (RLCISR3) HEX ADDRESS: 0XNB1C BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 147 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 140: RECEIVE LOOPBACK CODE 3 INTERRUPT ENABLE REGISTER (RLCIER3) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB1D TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 148 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 141: RECEIVE LOOPBACK CODE 4 INTERRUPT AND STATUS REGISTER (RLCISR4) HEX ADDRESS: 0XNB1E BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 149 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 142: RECEIVE LOOPBACK CODE 4 INTERRUPT ENABLE REGISTER (RLCIER4) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB1F TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 150 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 143: RECEIVE LOOPBACK CODE 5 INTERRUPT AND STATUS REGISTER (RLCISR5) HEX ADDRESS: 0XNB20 BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 151 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 144: RECEIVE LOOPBACK CODE 5 INTERRUPT ENABLE REGISTER (RLCIER5) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB21 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 152 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 145: RECEIVE LOOPBACK CODE 6 INTERRUPT AND STATUS REGISTER (RLCISR6) HEX ADDRESS: 0XNB22 BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 153 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 146: RECEIVE LOOPBACK CODE 6 INTERRUPT ENABLE REGISTER (RLCIER6) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB23 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 154 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 147: RECEIVE LOOPBACK CODE 7 INTERRUPT AND STATUS REGISTER (RLCISR7) HEX ADDRESS: 0XNB24 BIT FUNCTION 7-4 - TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved (For E1 mode only) 3 RXASTAT RO 0 Receive Loopback Activation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code, as specified in the Receive Loopback Activation Code Register (RLACR) if Receive Loopback Activation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Activation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Activation Code. 2 RXDSTAT RO 0 Receive Loopback Deactivation Code State This READ ONLY bit indicates whether or not the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code, as specified in the Receive Loopback Deactivation Code Register (RLDCR) if Receive Loopback Deactivation Code Detection is enabled. 0 = Indicates that the Receive T1 Framer Block is NOT currently detecting the Receive Loopback Deactivation Code. 1 = Indicates that the Receive T1 Framer Block is currently detecting the Receive Loopback Deactivation Code. 1 RXAINT RUR/ WC 0 Change in Receive Loopback Activation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Activation Code” interrupt has occurred since the last read of this register 0 RXDINT RUR/ WC 0 Change in Receive Loopback Deactivation Code interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has not occurred since the last read of this register 1 = Indicates that the “Change in Receive Loopback Deactivation Code” interrupt has occurred since the last read of this register 155 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 148: RECEIVE LOOPBACK CODE 7 INTERRUPT ENABLE REGISTER (RLCIER7) BIT FUNCTION 7-2 Reserved 1 RXAENB HEX ADDRESS: 0XNB25 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved R/W 0 Receive Loopback Activation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Activation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Activation Code. 0 - Disables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Activation Code” interrupt within the T1 Receive Framer. 0 RXDENB R/W 0 Receive Loopback Deactivation Code Interrupt Enable This bit enables or disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the Receive Loopback Deactivation Code. 2. Whenever the Receive T1 Framer block no longer detects the Receive Loopback Deactivation Code. 0 - Disables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 1 - Enables the “Change in Receive Loopback Deactivation Code” interrupt within the T1 Receive Framer. 156 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 149: DATA LINK STATUS REGISTER 3 (DLSR3) BIT FUNCTION REV. 1.0.1 HEX ADDRESS: 0XNB26 TYPE DEFAULT DESCRIPTION-OPERATION 7 MSG TYPE RUR/ WC 0 HDLC3 Message Type Identifier This READ ONLY bit indicates the type of data link message received by Receive HDLC 3 Controller. Two types of data link messages are supported within the XRT86VX38 device: Message Oriented Signaling (MOS) or Bit-Oriented Signalling (BOS). 0 = Indicates Bit-Oriented Signaling (BOS) type data link message is received 1 = Indicates Message Oriented Signaling (MOS) type data link message is received 6 TxSOT RUR/ WC 0 Transmit HDLC3 Controller Start of Transmission (TxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the “Transmit HDLC3 Controller Start of Transmission (TxSOT) “Interrupt has occurred since the last read of this register. Transmit HDLC3 Controller will declare this interrupt when it has started to transmit a data link message. For sending large HDLC messages, start loading the next available buffer once this interrupt is detected. 0 = Transmit HDLC3 Controller Start of Transmission (TxSOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC3 Controller Start of Transmission interrupt (TxSOT) has occurred since the last read of this register. 5 RxSOT RUR/ WC 0 Receive HDLC3 Controller Start of Reception (RxSOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC3 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register. Receive HDLC3 Controller will declare this interrupt when it has started to receive a data link message. 0 = Receive HDLC3 Controller Start of Reception (RxSOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC3 Controller Start of Reception (RxSOT) interrupt has occurred since the last read of this register 4 TxEOT RUR/ WC 0 Transmit HDLC3 Controller End of Transmission (TxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Transmit HDLC3 Controller End of Transmission (TxEOT) Interrupt has occurred since the last read of this register. Transmit HDLC3 Controller will declare this interrupt when it has completed its transmission of a data link message. For sending large HDLC messages, it is critical to load the next available buffer before this interrupt occurs. 0 = Transmit HDLC3 Controller End of Transmission (TxEOT) interrupt has not occurred since the last read of this register 1 = Transmit HDLC3 Controller End of Transmission (TxEOT) interrupt has occurred since the last read of this register 157 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 149: DATA LINK STATUS REGISTER 3 (DLSR3) BIT FUNCTION HEX ADDRESS: 0XNB26 TYPE DEFAULT DESCRIPTION-OPERATION 3 RxEOT RUR/ WC 0 Receive HDLC3 Controller End of Reception (RxEOT) Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receive HDLC3 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register. Receive HDLC3 Controller will declare this interrupt once it has completely received a full data link message, or once the buffer is full. 0 = Receive HDLC3 Controller End of Reception (RxEOT) interrupt has not occurred since the last read of this register 1 = Receive HDLC3 Controller End of Reception (RxEOT) Interrupt has occurred since the last read of this register 2 FCS Error RUR/ WC 0 FCS Error Interrupt Status This Reset-Upon-Read bit indicates whether or not the FCS Error Interrupt has occurred since the last read of this register. Receive HDLC3 Controller will declare this interrupt when it has detected the FCS error in the most recently received data link message. 0 = FCS Error interrupt has not occurred since the last read of this register 1 = FCS Error interrupt has occurred since the last read of this register 1 Rx ABORT RUR/ WC 0 Receipt of Abort Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Abort Sequence interrupt has occurred since last read of this register. Receive HDLC3 Controller will declare this interrupt if it detects the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) in the incoming data link channel. 0 = Receipt of Abort Sequence interrupt has not occurred since last read of this register 1 = Receipt of Abort Sequence interrupt has occurred since last read of this register 0 RxIDLE RUR/ WC 0 Receipt of Idle Sequence Interrupt Status This Reset-Upon-Read bit indicates whether or not the Receipt of Idle Sequence interrupt has occurred since the last read of this register. The Receive HDLC3 Controller will declare this interrupt if it detects the flag sequence octet (0x7E) in the incoming data link channel. If RxIDLE "AND" RxEOT occur together, then the entire HDLC message has been received. 0 = Receipt of Idle Sequence interrupt has not occurred since last read of this register 1 = Receipt of Idle Sequence interrupt has occurred since last read of this register. 158 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 150: DATA LINK INTERRUPT ENABLE REGISTER 3 (DLIER3) BIT FUNCTION TYPE DEFAULT - - Reserved REV. 1.0.1 HEX ADDRESS: 0XNB27 DESCRIPTION-OPERATION 7 Reserved 6 TxSOT ENB R/W 0 Transmit HDLC3 Controller Start of Transmission (TxSOT) Interrupt Enable This bit enables or disables the “Transmit HDLC3 Controller Start of Transmission (TxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC3 Controller will generate an interrupt when it has started to transmit a data link message. 0 = Disables the Transmit HDLC3 Controller Start of Transmission (TxSOT) interrupt. 1 = Enables the Transmit HDLC3 Controller Start of Transmission (TxSOT) interrupt. 5 RxSOT ENB R/W 0 Receive HDLC3 Controller Start of Reception (RxSOT) Interrupt Enable This bit enables or disables the “Receive HDLC3 Controller Start of Reception (RxSOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC3 Controller will generate an interrupt when it has started to receive a data link message. 0 = Disables the Receive HDLC3 Controller Start of Reception (RxSOT) interrupt. 1 = Enables the Receive HDLC3 Controller Start of Reception (RxSOT) interrupt. 4 TxEOT ENB R/W 0 Transmit HDLC3 Controller End of Transmission (TxEOT) Interrupt Enable This bit enables or disables the “Transmit HDLC3 Controller End of Transmission (TxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Transmit HDLC3 Controller will generate an interrupt when it has finished transmitting a data link message. 0 = Disables the Transmit HDLC3 Controller End of Transmission (TxEOT) interrupt. 1 = Enables the Transmit HDLC3 Controller End of Transmission (TxEOT) interrupt. 3 RxEOT ENB R/W 0 Receive HDLC3 Controller End of Reception (RxEOT) Interrupt Enable This bit enables or disables the “Receive HDLC3 Controller End of Reception (RxEOT) “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC3 Controller will generate an interrupt when it has finished receiving a complete data link message. 0 = Disables the Receive HDLC3 Controller End of Reception (RxEOT) interrupt. 1 = Enables the Receive HDLC3 Controller End of Reception (RxEOT) interrupt. 159 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 150: DATA LINK INTERRUPT ENABLE REGISTER 3 (DLIER3) BIT FUNCTION TYPE DEFAULT HEX ADDRESS: 0XNB27 DESCRIPTION-OPERATION 2 FCS ERR ENB R/W 0 FCS Error Interrupt Enable This bit enables or disables the “Received FCS Error “Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC3 Controller will generate an interrupt when it has detected the FCS error within the incoming data link message. 0 = Disables the “Receive FCS Error” interrupt. 1 = Enables the “Receive FCS Error” interrupt. 1 RxABORT ENB R/W 0 Receipt of Abort Sequence Interrupt Enable This bit enables or disables the “Receipt of Abort Sequence“ Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC3 Controller will generate an interrupt when it has detected the Abort Sequence (i.e. a string of seven (7) consecutive 1’s) within the incoming data link channel. 0 = Disables the “Receipt of Abort Sequence” interrupt. 1 = Enables the “Receipt of Abort Sequence” interrupt. 0 RxIDLE ENB R/W 0 Receipt of Idle Sequence Interrupt Enable This bit enables or disables the “Receipt of Idle Sequence“ Interrupt within the XRT86VX38 device. Once this interrupt is enabled, the Receive HDLC3 Controller will generate an interrupt when it has detected the Idle Sequence Octet (i.e. 0x7E) within the incoming data link channel. 0 = Disables the “Receipt of Idle Sequence” interrupt. 1 = Enables the “Receipt of Idle Sequence” interrupt. 160 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 151: SS7 STATUS REGISTER FOR LAPD3 (SS7SR3) BIT 0 0 HEX ADDRESS: 0XNB28 FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION SS7_3_STATUS RUR/ WC 0 SS7 Interrupt Status for LAPD Controller 3 This Reset-Upon-Read bit field indicates whether or not the “SS7” interrupt has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 = Indicates that the “SS7” interrupt has not occurred since the last read of this register 1 = Indicates that the “SS7” interrupt has occurred since the last read of this register TABLE 152: SS7 ENABLE REGISTER FOR LAPD3 (SS7ER3) BIT REV. 1.0.1 FUNCTION SS7_3_ENB TYPE DEFAULT R/W 0 HEX ADDRESS: 0XNB29 DESCRIPTION-OPERATION SS7 Interrupt Enable for LAPD Controller 3 This bit enables or disables the “SS7” interrupt within the LAPD Controller 3. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt when the Received LAPD message is more than 276 Bytes in length. 0 - Disables the “SS7” interrupt within the LAPD Controller 3. 1 - Enables the “SS7” interrupt within the LAPD Controller 3. 161 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 153: CUSTOMER INSTALLATION ALARM STATUS REGISTER (CIASR) BIT FUNCTION [7:6] Reserved 5 RxAIS-CI_state HEX ADDRESS: 0XNB40 TYPE DEFAULT DESCRIPTION-OPERATION - - Reserved RO 0 Receive Alarm Indication Signal-Customer Installation (AIS-CI) State This READ ONLY bit field indicates whether or not the Receive T1 Framer is currently detecting the Alarm Indication Signal-Customer Installation (AISCI) condition. Alarm Indication Signal-Customer Installation (AIS-CI) is intended for use in a network to differentiate between an issue within the network or the Customer Installation (CI). AIS-CI is an all ones signal with an embedded signature of 01111100 11111111 (right-to left) which recurs at 386 bit intervals in-the DS-1 signal. 0 = Indicates the Receive T1 Framer is currently NOT detecting the AIS-CI condition 1 = Indicates the Receive T1 Framer is currently detecting the AIS-CI condition NOTE: This bit only works if AIS-CI detection is enabled (Register 0xN11C) 4 RxRAI-CI_state RO 0 Rx RAI-CI State This READ ONLY bit field indicates whether or not the Receive T1 Framer is currently declaring the Remote Alarm Indication - Customer Installation (RAI-CI) condition. (This is for T1 ESF framing mode only) Remote Alarm Indication - Customer Installation (RAI-CI) is intended for use in a network to differentiate between an issue within the network or the Customer Installation (CI). RAI-CI is a repetitive pattern with a period of 1.08 seconds. It is comprised of 0.99 seconds of RAI message (00000000 11111111 Right-to-left) and a 90 ms of RAI-CI signature (00111110 11111111 Right to left) to form a RAI-CI signal. 0 = Indicates the Receive T1 Framer is currently NOT detecting the RAI-CI condition 1 = Indicates the Receive T1 Framer is currently detecting the RAI-CI condition NOTE: This bit only works if RAI-CI detection is enabled (Register 0xN11C) [3:2] Reserved - - Reserved 162 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 153: CUSTOMER INSTALLATION ALARM STATUS REGISTER (CIASR) BIT 1 FUNCTION RxAIS-CI REV. 1.0.1 HEX ADDRESS: 0XNB40 TYPE DEFAULT DESCRIPTION-OPERATION RUR/ WC 0 Change in Receive AIS-CI Condition Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in AISCI Condition” interrupt within the T1 Receive Framer Block has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the AIS-CI Condition. 2. Whenever the Receive T1 Framer block clears the AIS-CI Condition 0 = Indicates the “Change in AIS-CI Condition” interrupt has NOT occurred since the last read of this register 1 = Indicates the “Change in AIS-CI Condition” interrupt has occurred since the last read of this register 0 RxRAI-CI RUR/ WC 0 Change in Receive RAI-CI Condition Interrupt Status This Reset-Upon-Read bit field indicates whether or not the “Change in RAICI Condition” interrupt within the T1 Receive Framer Block has occurred since the last read of this register. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the RAI-CI Condition. 2. Whenever the Receive T1 Framer block clears the RAI-CI Condition 0 = Indicates the “Change in RAI-CI Condition” interrupt has NOT occurred since the last read of this register 1 = Indicates the “Change in RAI-CI Condition” interrupt has occurred since the last read of this register TABLE 154: CUSTOMER INSTALLATION ALARM STATUS REGISTER (CIAIER) HEX ADDRESS: 0XNB41 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 RxAIS-CI_ENB R/W 0 Change in Receive AIS-CI Condition Interrupt Enable This bit enables or disables the “Change in AIS-CI Condition” interrupt within the T1 Receive Framer Block. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the AIS-CI Condition. 2. Whenever the Receive T1 Framer block clears the AIS-CI Condition 0 - Disables the “Change in AIS-CI Condition” interrupt. 1 - Enables the “Change in AIS-CI Condition” interrupt. 0 RxRAI-CI_ENB R/W 0 Change in Receive RAI-CI Condition Interrupt Enable This bit enables or disables the “Change in RAI-CI Condition” interrupt within the T1 Receive Framer Block. If this interrupt is enabled, then the Receive T1 Framer block will generate an interrupt in response to either one of the following conditions. 1. Whenever the Receive T1 Framer block detects the RAI-CI Condition. 2. Whenever the Receive T1 Framer block clears the AIS-CI Condition 0 - Disables the “Change in RAI-CI Condition” interrupt. 1 - Enables the “Change in RAI-CI Condition” interrupt. 163 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 155: T1 BOC INTERRUPT STATUS REGISTER (BOCISR 0XNB70H) BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 RMTCH3 RMTCH2 BOCC RFDLAD RFDLF TFDLE RMTCH1 RBOC RUR RUR RUR RUR RUR RUR RUR RUR 0 0 0 0 0 0 0 0 BIT 7 - Receive FDL Match 3 Event This bit is set when the receive FDL message is equal to the RFDL Match 3 message, and filter validation has occured. } 0 - No Match } 1 - Match 3 BIT 6 - Receive FDL Match 2 Event This bit is set when the receive FDL message is equal to the RFDL Match 2 message, and filter validation has occured. } 0 - No Match } 1 - Match 2 BIT 5 - BOC Clear Event (Loss of BOC) This bit is set when 3 or more consecutive Non-BOC messages occur (Non-BOC means that the message meets the ’0xxxxxx011111111’ framing format, but does not contain a valid BOC). } 0 - No Change } 1 - BOC Cleared BIT 4 - RFDL Abort Detect Event This bit is set when nine consecutive ones are detected within the FDL bits. } 0 - Normal } 1 - RFDL Abort BIT 3 - RFDL Register Full Event (Receive Start of Transfer) This bit is set when the RFDL register is full. This register is not gated by the filter. } 0 - Not Full } 1 - Full 164 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 BIT 2 - TFDL Register Empty Event (Transmit End of Transfer) This bit is set when the TFDL register has been emptied according to amount of repetitions programmed into the TxBYTE count register 0xn178h. This alarm is meant to be an indicator of a complete BOC transmission for system alert or to initiate a response for future processing. } 0 - Not Emptied } 1 - Emptied BIT 1 - Receive FDL Match 1 Event This bit is set when the receive FDL message is equal to the RFDL Match 1 message, and filter validation has occured. } 0 - No Match } 1 - Match 1 BIT 0 - Receive BOC Detector Change of Status This bit is set to 1 any time a change has occured with the RFDL message. This alarm will NOT be set unless the filter setting has been satisfied. } 0 - No Change } 1 - Change of Status 165 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 156: T1 BOC INTERRUPT ENABLE REGISTER (BOCIER 0XNB71H) BIT7 BIT6 BIT5 BIT4 BIT3 BIT2 BIT1 BIT0 RMTCH3 RMTCH2 BOCC RFDLAD RFDLF TFDLE RMTCH1 RBOC R/W R/W R/W R/W R/W R/W R/W R/W 0 0 0 0 0 0 0 0 BIT 7 - Receive FDL Match 3 Event This bit is used to enable the RFDL Match 3 message Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 6 - Receive FDL Match 2 Event This bit is used to enable the RFDL Match 2 message Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 5 - BOC Clear Event This bit is used to enable the BOC Clear Event Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 4 - RFDL Abort Detect Event This bit is used to enable the RFDL Abort Detect Event Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 3 - RFDL Register Full Event This bit is used to enable the RFDL Full Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 2 - TFDL Register Empty Event This bit is used to enable the TFDL Empty Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 1 - Receive FDL Match 1 Event This bit is used to enable the RFDL Match 1 message Interrupt. } 0 - Disabled } 1 - Interrupt Enabled BIT 0 - Receive BOC Detector Change of Status This bit is used to enable the BOC detector change of status Interrupt. } 0 - Disabled } 1 - Interrupt Enabled 166 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 157: T1 BOC UNSTABLE INTERRUPT STATUS REGISTER (BOCUISR 0XNB74H) BIT7 BIT6 BIT5 BIT4 Reserved Unstable RUR RUR RUR RUR 0 0 0 0 BIT3 BIT2 BIT1 BIT0 RUR RUR RUR RUR 0 0 0 0 Reserved BIT 7 - Reserved BIT 6 - Unstable SSM Message Interrupt Status This bit will be set to ’1’ anytime the receive SSM message has changed from its previous value, IF the SSM message was valid. Therefore, this interrupt is only active once the BOC has received a valid SSM message. This register is Reset Upon Read. } 0 - No Change in SSM } 1 - Change in SSM BITS [5:0] - Reserved 167 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 158: T1 BOC UNSTABLE INTERRUPT ENABLE REGISTER (BOCUIER 0XNB75H) BIT7 BIT6 BIT5 BIT4 Reserved Unstable R/W R/W R/W R/W 0 0 0 0 BIT3 BIT2 BIT1 BIT0 R/W R/W R/W R/W 0 0 0 0 Reserved BIT 7 - Reserved BIT 6 - Unstable SSM Message Interrupt Enable This bit is used to enable the Unstable SSM message Interrupt. Unstable is defined as anytime the receive SSM message has changed from its previous value, IF the SSM message was valid. Therefore, this interrupt is only active once the BOC has received a valid SSM message. } 0 - Disabled } 1 - Interrupt Enabled BITS [5:0] - Reserved 168 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 2.0 LINE INTERFACE UNIT (LIU SECTION) REGISTERS TABLE 159: LIU CHANNEL CONTROL REGISTER 0 (LIUCCR0) BIT FUNCTION TYPE DEFAULT 7 QRSS_n/ PRBS_n R/W 0 HEX ADDRESS: 0X0FN0 DESCRIPTION-OPERATION QRSS/PRBS Select Bits These bits are used to select between QRSS and PRBS. 0 = PRBS_n (215 - 1) 1 = QRSS_n (220 - 1) 6 PRBS_Rx_n/ R/W 0 PRBS_Tx_n PRBS Receive/Transmit Select: This bit is used to select where the output of the PRBS Generator is directed if PRBS generation is enabled. 0 = Normal Operation - PRBS generator is output on TTIP and TRING if PRBS generation is enabled. 1 = PRBS Generator is output on RPOS and RCLK. Bit 6 = "0" + PBRS Generator - TTIP Tx TRING Bit 6 = "1" + PBRS Generator 5 RXON_n R/W 0 - RPOS Rx RNEG Receiver ON: This bit permits the user to either turn on or turn off the Receive Section of XRT86VX38. If the user turns on the Receive Section, then XRT86VX38 will begin to receive the incoming data-stream via the RTIP and RRING input pins. Conversely, if the user turns off the Receive Section, then the entire Receive Section except the MCLKIN Phase Locked Loop (PLL) will be powered down. 0 = Shuts off the Receive Section of XRT86VX38. 1 = Turns on the Receive Section of XRT86VX38. 169 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 159: LIU CHANNEL CONTROL REGISTER 0 (LIUCCR0) HEX ADDRESS: 0X0FN0 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 4-0 EQC[4:0] R/W 00000 Equalizer Control [4:0]: These bits are used to control the transmit pulse shaping, transmit line build-out (LBO) and receive sensitivity level. The Transmit Pulse Shape can be controlled by adjusting the Transmit Line Build-Out Settings for different cable length in T1 mode. Transmit pulse shape can also be controlled by using the Arbitrary mode, where users can specify the amplitude of the pulse shape by using the 8 Arbitrary Pulse Segments provided in the LIU registers (0xNF08-0xNF0F), where n is the channel number. The XRT86VX38 device supports both long haul and short haul applications which can also be selected using the EQC[4:0] bits. Table 160.presents the corresponding Transmit Line Build Out and Receive Sensitivity settings using different combinations of these five EQC[4:0] bits. 170 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 160: EQUALIZER CONTROL AND TRANSMIT LINE BUILD OUT EQC[4:0] T1 MODE/RECEIVE SENSITIVITY TRANSMIT LBO CABLE 0xN0h T1 Long Haul/36dB 0dB 100TP 0xN1h T1 Long Haul/36dB -7.5dB 100TP 0xN2h T1 Long Haul/36dB -15dB 100TP 0xN3h T1 Long Haul/36dB -22.5dB 100TP 0xN4h T1 Long Haul/45dB 0dB 100TP 0xN5h T1 Long Haul/45dB -7.5dB 100TP 0xN6h T1 Long Haul/45dB -15dB 100TP 0xN7h T1 Long Haul/45dB -22.5dB 100TP 0xN8h T1 Short Haul/15dB 0 to 133 feet (0.6dB) 100TP 0xN9h T1 Short Haul/15dB 133 to 266 feet (1.2dB) 100TP 0xNAh T1 Short Haul/15dB 266 to 399 feet (1.8dB) 100TP 0xNBh T1 Short Haul/15dB 399 to 533 feet (2.4dB) 100TP 0xNCh T1 Short Haul/15dB 533 to 655 feet (3.0dB) 100TP 0xNDh T1 Short Haul/15dB Arbitrary Pulse 100TP 0xNEh T1 Gain Mode/29dB 0 to 133 feet (0.6dB) 100TP 0xNFh T1 Gain Mode/29dB 133 to 266 feet (1.2dB) 100TP 0x10h T1 Gain Mode/29dB 266 to 399 feet (1.8dB) 100TP 0x11h T1 Gain Mode/29dB 399 to 533 feet (2.4dB) 100TP 0x12h T1 Gain Mode/29dB 533 to 655 feet (3.0dB) 100TP 0x13h T1 Gain Mode/29dB Arbitrary Pulse 100TP 0x14h T1 Gain Mode/29dB 0dB 100TP 0x15h T1 Gain Mode/29dB -7.5dB 100TP 0x16h T1 Gain Mode/29dB -15dB 100TP 0x17h T1 Gain Mode/29dB -22.5dB 100TP 0x18h E1 Long Haul/36dB ITU G.703 75 Coax 0x19h E1 Long Haul/36dB ITU G.703 120 TP 0x1Ah E1 Long Haul/45dB ITU G.703 75 Coax 0x1Bh E1 Long Haul/45dB ITU G.703 120 TP 0x1Ch E1 Short Haul/15dB ITU G.703 75 Coax 0x1Dh E1 Short Haul/15dB ITU G.703 120 TP 0x1Eh E1 Gain Mode/29dB ITU G.703 75 Coax 0x1Fh E1 Gain Mode/29dB ITU G.703 120 TP 171 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 161: LIU CHANNEL CONTROL REGISTER 1 (LIUCCR1) HEX ADDRESS: 0X0FN1 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 RXTSEL_n R/W 0 Receiver Termination Select: Upon power up, the receivers are in “High” impedance. The receive termination can be selected by setting this bit according to the following table: RXTSEL 6 5-4 TXTSEL_n TERSEL[1:0] R/W R/W 0 00 RxJASEL_n R/W 0 0 "High" Impedance 1 Internal Transmit Termination Select: This bit is used to select between internal termination or “High” impedance modes for the T1 transmitter according to the following table: TXTSEL TX Termination 0 "High" Impedance 1 Internal Termination Impedance Select [1:0]: These bits are used to control the transmit and receive termination impedance when the LIU block is configured in Internal Termination Mode. In internal termination mode, (i.e., TXTSEL = “1” and RXTSEL = “1”), internal transmit and receive termination can be selected according to the following table: NOTE: 3 RX Termination TERSEL1 TERSEL0 Internal Transmit and Receive Termination 0 0 100 0 1 110 1 0 75 1 1 120 In the internal termination mode, the transmitter output should be AC coupled to the transformer. Receive Jitter Attenuator Enable This bit permits the user to enable or disable the Jitter Attenuator in the Receive Path within the XRT86VX38 device. 0 = Disables the Jitter Attenuator to operate in the Receive Path within the Receive T1 LIU Block. 1 = Enables the Jitter Attenuator to operate in the Receive Path within the Receive T1 LIU Block. 172 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 161: LIU CHANNEL CONTROL REGISTER 1 (LIUCCR1) REV. 1.0.1 HEX ADDRESS: 0X0FN1 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 2 TxJASEL_n R/W 0 Transmit Jitter Attenuator Enable This bit permits the user to enable or disable the Jitter Attenuator in the Transmit Path within the XRT86VX38 device. 0 = Disables the Jitter Attenuator to operate in the Transmit Path within the Transmit T1 LIU Block. 1 = Enables the Jitter Attenuator to operate in the Transmit Path within the Transmit T1 LIU Block. 1 JABW_n R/W 0 Jitter Attenuator Bandwidth Select: In T1 mode, the Jitter Attenuator Bandwidth is always 3Hz, and this bit has no effect on the Jitter Attenuator Bandwidth. The FIFOS (bit D0 of this register) will be used to select the FIFO size, according to the table below. 0 FIFOS_n R/W 0 Mode JABW bit D1 FIFOS_n bit D0 JA B-W Hz FIFO Size T1 0 0 3 32 T1 0 1 3 64 T1 1 0 3 32 T1 1 1 3 64 E1 0 0 10 32 E1 0 1 10 64 E1 1 0 1.5 64 E1 1 1 1.5 64 FIFO Size Select: See table of bit D1 above for the function of this bit. 173 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 162: LIU CHANNEL CONTROL REGISTER 2 (LIUCCR2) BIT FUNCTION TYPE DEFAULT 7 INVQRSS_n R/W 0 6-4 TXTEST[2:0] R/W 000 HEX ADDRESS: 0X0FN2 DESCRIPTION-OPERATION Invert QRSS Pattern: This bit inverts the output PRBS/QRSS pattern if the LIU Block is configured to transmit a PRBS/QRSS pattern. 0 = The LIU will NOT invert the output PRBS/QRSS pattern 1 = The LIU will invert the output PRBS/QRSS pattern Transmit Test Pattern [2:0]: These bits are used to configure the Transmit T1 LIU Block to generate and transmit test patterns according to the following table. Use of these bits automatically places the LIU section in Single Rail mode. When this happens, the Framer section must be placed in Single Rail mode in Reg 0xN101. TXTEST2 TXTEST1 TXTEST0 Test Pattern 0 X X No Pattern 1 0 0 TDQRSS 1 0 1 TAOS 1 1 0 TLUC 1 1 1 TLDC TDQRSS (Transmit/Detect Quasi-Random Signal): QRSS pattern is a 220-1 pseudo-random bit sequence (PRBS) with no more than 14 consecutive zeros. TAOS (Transmit All Ones): Whenever the user implements this configuration setting, the Transmit T1 LIU Block will ignore the data that it is accepting from the Transmit T1 Framer block (as well as the upstream system-side terminal equipment) and overwrite this data with the All Ones Pattern. TLUC (Transmit Network Loop-Up Code): The Transmit T1 LIU Block will generate and transmit the Network Loop-Up Code of “00001” to the line for the selected channel number n. When Network Loop-Up code is being transmitted, the XRT86VX38 will ignore the “Automatic Loop-Code detection and Remote LoopBack activation” (NLCDE1 =“1”, NLCDE0 =“1” of register 0xNF03) in order to avoid activating Remote Digital Loop-Back automatically when the remote terminal responds to the Loop-Back request. TLDC (Transmit Network Loop-Down Code): The Transmit T1 LIU Block will generate and transmit the Network Loop-Down Code of “001” to the line for the selected channel number n. 174 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 162: LIU CHANNEL CONTROL REGISTER 2 (LIUCCR2) REV. 1.0.1 HEX ADDRESS: 0X0FN2 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 3 TXON_n R/W 0 Transmitter ON: This bit permits the user to either turn on or turn off the Transmit Driver of XRT86VX38. If the user turns on the Transmit Driver, then XRT86VX38 will begin to transmit T1 data (on the line) via the TTIP and TRING output pins. Conversely, if the user turns off the Transmit Driver, then the TTIP and TRING output pins will be tri-stated. 0 = Shuts off the Transmit Driver associated with the XRT86VX38 device and tri-states the TTIP and TRING output pins. 1 = Turns on the Transmit Driver associated with the XRT86VX38 device. NOTE: If the user wishes to exercise software control over the state of the Transmit Driver of the XRT86VX38, then it is imperative that the user pull the TxON pin to a logic “HIGH” level. 2-0 LOOP2_n R/W 000 Loop-Back control [2:0]: These bits control the Loop-Back Modes of the LIU section, according to the table below. LOOP2 LOOP1 LOOP0 0 X X No Loop-Back 1 0 0 Dual Loop-Back 1 0 1 Analog Loop-Back 1 1 0 Remote Loop-Back 1 1 1 Digital Loop-Back 175 Loop-Back Mode XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 163: LIU CHANNEL CONTROL REGISTER 3 (LIUCCR3) HEX ADDRESS: 0X0FN3 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7-6 NLCDE[1:0] R/W 00 Network Loop Code Detection Enable [1:0]: These bits are used to control the Loop-Code detection on the receive path, according to the table below. This part must be in Single Rail mode to detect.. NETWORK LOOP CODE DETECTION ENABLE NLCDE[1:0] 00 Disables Loop Code Detection 01 Enables Loop-Up Code Detection on the Receive Path. 10 Enables Loop-Down Code Detection on the Receive Path. 11 Enables Automatic Loop-Up Code Detection on the Receive Path and Remote Loop-Back Activation upon detecting Loop-Up Code. Loop-Up Code Detection Enable: The XRT86VX38 is configured to monitor the receive data for the Loop-Up code Pattern (i.e. a string of four ‘0’s followed by one ‘1’ pattern). When the presence of the “00001” pattern is detected for more than 5 seconds, the status of the NLCD bit (bit 3 of register 0xNF05) is set to “1” and if the NLCD interrupt is enabled (bit 3 of register 0xNF04), an interrupt will be generated. Loop-Down Code Detection Enable: The XRT86VX38 is configured to monitor the receive data for the Loop-Down code Pattern (i.e. a string of two ‘0’s followed by one ‘1’ pattern). When the presence of the “001” pattern is detected for more than 5 seconds, the status of the NLCD bit (bit 3 of register 0xNF05) is set to “1” and if the NLCD interrupt is enabled (bit 3 of register 0xNF04), an interrupt will be generated. Automatic Loop-Up Code Detection and Remote Loop Back Activation Enable: When this mode is enabled, the state of the NLCD bit (bit 3 of register 0xNF05) is reset to “0” and the XRT86VX38 is configured to monitor the receive data for the Loop-Up code. If the “00001” pattern is detected for longer than 5 seconds, then the NLCD bit (bit 3 of register 0xNF05) is set “1”, and Remote Loop-Back is activated. Once the remote loop-back is activated, the XRT86VX38 is automatically programmed to monitor the receive data for the LoopDown code. The NLCD bit stays set even after the chip stops receiving the Loop-Up code. The Remote Loop-Back condition is removed only when the XRT86VX38 receives the Loop-Down code for more than 5 seconds or if the Automatic Loop-Code detection mode is terminated. 5-2 Reserved R/W 0 This Bit Is Not Used 176 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 163: LIU CHANNEL CONTROL REGISTER 3 (LIUCCR3) REV. 1.0.1 HEX ADDRESS: 0X0FN3 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 INSBER_n R/W 0 Insert Bit Error: This bit is used to insert a single bit error on the transmitter of the T1 LIU Block. When the T1 LIU Block is configured to transmit and detect the QRSS pattern, (i.e., TxTEST[2:0] bits set to ‘b100’), a “0” to “1” transition of this bit will insert a bit error in the transmitted QRSS pattern of the selected channel number n. The state of this bit is sampled on the rising edge of the respective TCLK_n. NOTE: To ensure the insertion of bit error, a “0” should be written in this bit location before writing a “1”. 0 Reserved R/W 0 This Bit Is Not Used 177 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 164: LIU CHANNEL CONTROL INTERRUPT ENABLE REGISTER (LIUCCIER) HEX ADDRESS: 0X0FN4 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 Reserved RO 0 This Bit Is Not Used 6 DMOIE_n R/W 0 Change of Transmit DMO (Drive Monitor Output) Condition Interrupt Enable: This bit permits the user to either enable or disable the “Change of Transmit DMO Condition” Interrupt. If the user enables this interrupt, then the XRT86VX38 device will generate an interrupt any time when either one of the following events occur. 1. Whenever the Transmit Section toggles the DMO Status bit (Bit 6 or Register 0xNF05) to “1”. 2. Whenever the Transmit Section toggles the DMO Status bit (Bit 6 or Register 0xNF05) to “0”. 0 – Disables the “Change in the DMO Condition” Interrupt. 1 – Enables the “Change in the DMO Condition” Interrupt. 5 FLSIE_n R/W 0 FIFO Limit Status Interrupt Enable: This bit permits the user to either enable or disable the “FIFO Limit Status” Interrupt. If the user enables this interrupt, then the XRT86VX38 device will generate an interrupt when the jitter attenuator Read/Write FIFO pointers are within +/- 3 bits. 0 = Disables the “FIFO Limit Status” Interrupt 1 = Enables the “FIFO Limit Status” Interrupt 4 Reserved - - This bit is not used. 3 NLCDIE_n R/W 0 Change in Network Loop-Code Detection Interrupt Enable: This bit permits the user to either enable or disable the “Change in Network Loop-Code Detection” Interrupt. If the user enables this interrupt, then the XRT86VX38 device will generate an interrupt any time when either one of the following events occur. 1. Whenever the Receive Section (within XRT86VX38) detects the Network Loop-Code (Loop-Up or Loop-Down depending on which Loop-Code the Receive LIU is configured to detect). 2. Whenever the Receive Section (within XRT86VX38) no longer detects the Network Loop-Code (Loop-Up or Loop-Down depending on which Loop-Code the Receive LIU is configured to detect). 0 – Disables the “Change in Network Loop-Code Detection” Interrupt. 1 – Enables the “Change in Network Loop-Code Detection” Interrupt. 2 Reserved - - This bit is not used 178 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 164: LIU CHANNEL CONTROL INTERRUPT ENABLE REGISTER (LIUCCIER) REV. 1.0.1 HEX ADDRESS: 0X0FN4 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 RLOSIE_n R/W 0 Change of the Receive LOS (Loss of Signal) Defect Condition Interrupt Enable: This bit permits the user to either enable or disable the “Change of the Receive LOS Defect Condition” Interrupt. If the user enables this interrupt, then the XRT86VX38 device will generate an interrupt any time when either one of the following events occur. 1. Whenever the Receive Section (within XRT86VX38) declares the LOS Defect Condition. 2. Whenever the Receive Section (within XRT86VX38) clears the LOS Defect condition. 0 – Disables the “Change in the LOS Defect Condition” Interrupt. 1 – Enables the “Change in the LOS Defect Condition” Interrupt. 0 QRPDIE_n R/W 0 Change in QRSS Pattern Detection Interrupt Enable: This bit permits the user to either enable or disable the “Change in QRSS Pattern Detection” Interrupt. If the user enables this interrupt, then the XRT86VX38 device will generate an interrupt any time when either one of the following events occur. 1. Whenever the Receive Section (within XRT86VX38) detects the QRSS Pattern. 2. Whenever the Receive Section (within XRT86VX38) no longer detects the QRSS Pattern. 0 – Disables the “Change in QRSS Pattern Detection” Interrupt. 1 – Enables the “Change in QRSS Pattern Detection” Interrupt. NOTE: Register 0xNF04, 0xNF05 and 0xNF06 only work if the LIU is placed in Single Rail mode. If done so, the Framer block must also be placed in Single Rail mode in Register 0xN101. 179 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 165: LIU CHANNEL CONTROL STATUS REGISTER (LIUCCSR) BIT FUNCTION TYPE DEFAULT 7 Reserved RO 0 6 DMO_n RO 0 HEX ADDRESS: 0X0FN5 DESCRIPTION-OPERATION Driver Monitor Output (DMO) Status: This READ-ONLY bit indicates whether or not the Transmit Section is currently declaring the DMO Alarm condition. The Transmit Section will check the Transmit Output T1 Line signal for bipolar pulses via the TTIP and TRING output signals. If the Transmit Section were to detect no bipolar signal for 128 consecutive bit-periods, then it will declare the Transmit DMO Alarm condition. This particular alarm can be used to check for fault conditions on the Transmit Output Line Signal path. The Transmit Section will clear the Transmit DMO Alarm condition the instant that it detects some bipolar activity on the Transmit Output Line signal. 0 = Indicates that the Transmit Section of XRT86VX38 is NOT currently declaring the Transmit DMO Alarm condition. 1 = Indicates that the Transmit Section of XRT86VX38 is currently declaring the Transmit DMO Alarm condition. NOTE: If the DMO interrupt is enabled (DMOIE - bit D6 of register 0xNF04), any transition on this bit will generate an Interrupt. 5 FLS_n RO 0 FIFO Limit Status: This READ-ONLY bit indicates whether or not the XRT86VX38 is currently declaring the FIFO Limit Status. This bit is set to a “1” to indicate that the jitter attenuator Read/Write FIFO pointers are within +/- 3 bits. 0 = Indicates that the XRT86VX38 is NOT currently declaring the FIFO Limit Status. 1 = Indicates that the XRT86VX38 is currently declaring the FIFO Limit Status. NOTE: If the FIFO Limit Status Interrupt is enabled, (FLSIE bit - bit D5 of register 0xNF04), any transition on this bit will generate an Interrupt. 4 Reserved - 0 This Bit Is Not Used 180 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 165: LIU CHANNEL CONTROL STATUS REGISTER (LIUCCSR) REV. 1.0.1 HEX ADDRESS: 0X0FN5 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 3 NLCD_n RO 0 Network Loop-Code Detection Status Bit: This bit operates differently in the Manual or the Automatic Network Loop-Code detection modes. Manual Loop-Up Code detection mode (.i.e If NLCDE1 = “0” and NLCDE0 = “1”), this bit gets set to “1” as soon as the Loop-Up Code (“00001”) is detected in the receive data for longer than 5 seconds. This bit stays high as long as the Receive T1 LIU Block detects the presence of the Loop-Up code in the receive data and it is reset to “0” as soon as it stops receiving the Loop-Up Code. If the NLCD interrupt is enabled, the XRT86VX38 will initiate an interrupt on every transition of the NLCD status bit. Manual Loop-Down Code detection mode (i.e., If NLCDE1 = “1” and NLCDE0 = “0”), this bit gets set to “1” as soon as the Loop-Down Code (“001”) is detected in the receive data for longer than 5 seconds. This bit stays high as long as the Receive T1 LIU Block detects the presence of the Loop-Down code in the receive data and it is reset to “0” as soon as it stops receiving the Loop-Down Code. If the NLCD interrupt is enabled, the XRT86VX38 will initiate an interrupt on every transition of the NLCD status bit. Automatic Loop-code detection mode (i.e., If NLCDE1 = “1” and NLCDE0 =”1”), the state of the NLCD status bit is reset to “0” and the XRT86VX38 is programmed to monitor the receive input data for the Loop-Up code. This bit is set to a “1” to indicate that the Network Loop Code is detected for more than 5 seconds. Simultaneously, the Remote Loop-Back condition is automatically activated and the XRT86VX38 is programmed to monitor the receive data for the Network Loop Down code. The NLCD bit stays ‘high’ as long as the Remote LoopBack condition is in effect even if the chip stops receiving the LoopUp code. Remote Loop-Back is removed only if the XRT86VX38 detects the Loop-Down Code “001” pattern for longer than 5 seconds in the receive data. Upon detecting the Loop-Down Code “001” pattern, the XRT86VX38 will reset the NLCD status bit and an interrupt will be generated if the NLCD interrupt enable bit is enabled. Users can monitor the state of this bit to determine if the Remote Loop-Back is activated. 2 Reserved - 0 This Bit Is Not Used 1 RLOS_n RO 0 Receive Loss of Signal Defect Condition Status: This READ-ONLY bit indicates whether or not the Receive LIU Block is currently declaring the LOS defect condition. 0 = Indicates that the Receive Section is NOT currently declaring the LOS Defect Condition. 1 = Indicates that the Receive Section is currently declaring the LOS Defect condition. NOTE: If the RLOSIE bit (bit D1 of Register 0xNF04) is enabled, any transition on this bit will generate an Interrupt. 181 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 165: LIU CHANNEL CONTROL STATUS REGISTER (LIUCCSR) HEX ADDRESS: 0X0FN5 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 0 QRPD_n RO 0 Quasi-random Pattern Detection Status: This READ-ONLY bit indicates whether or not the Receive LIU Block is currently declaring the QRSS Pattern LOCK status. 0 = Indicates that the XRT86VX38 is NOT currently declaring the QRSS Pattern LOCK. 1 = Indicates that the XRT86VX38 is currently declaring the QRSS Pattern LOCK. NOTE: If the QRPDIE bit (bit D0 of register 0xNF04) is enabled, any transition on this bit will generate an Interrupt. NOTE: Register 0xNF04, 0xNF05 and 0xNF06 only work if the LIU is placed in Single Rail mode. If done so, the Framer block must also be placed in Single Rail mode in Register 0xN101. 182 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 166: LIU CHANNEL CONTROL INTERRUPT STATUS REGISTER (LIUCCISR) BIT FUNCTION TYPE DEFAULT 7 Reserved RO 0 6 DMOIS_n RUR/ WC 0 REV. 1.0.1 HEX ADDRESS: 0X0FN6 DESCRIPTION-OPERATION Change of Transmit DMO (Drive Monitor Output) Condition Interrupt Status: This RESET-upon-READ bit indicates whether or not the “Change of the Transmit DMO Condition” Interrupt has occurred since the last read of this register. 0 = Indicates that the “Change of the Transmit DMO Condition” Interrupt has NOT occurred since the last read of this register. 1 = Indicates that the “Change of the Transmit DMO Condition” Interrupt has occurred since the last read of this register. This bit is set to a “1” every time when DMO_n status bit (bit 6 of Register 0xNF05) has changed since the last read of this register. NOTE: Users can determine the current state of the “Transmit DMO Condition” by reading out the content of bit 6 within Register 0xNF05 5 FLSIS_n RUR/ WC 0 FIFO Limit Interrupt Status: This RESET-upon-READ bit indicates whether or not the “FIFO Limit” Interrupt has occurred since the last read of this register. 0 = Indicates that the “FIFO Limit Status” Interrupt has NOT occurred since the last read of this register. 1 = Indicates that the “FIFO Limit Status” Interrupt has occurred since the last read of this register. This bit is set to a “1” every time when FIFO Limit Status bit (bit 5 of Register 0xNF05) has changed since the last read of this register. NOTE: Users can determine the current state of the “FIFO Limit” by reading out the content of bit 5 within Register 0xNF05 4 Reserved - - This bit is not used 3 NLCDIS_n RUR/ WC 0 Change in Network Loop-Code Detection Interrupt Status: This RESET-upon-READ bit indicates whether or not the “Change in Network Loop-Code Detection” Interrupt has occurred since the last read of this register. 0 = Indicates that the “Change in Network Loop-Code Detection” Interrupt has NOT occurred since the last read of this register. 1 = Indicates that the “Change in Network Loop-Code Detection” Interrupt has occurred since the last read of this register. This bit is set to a “1” every time when NLCD status bit (bit 3 of Register 0xNF05) has changed since the last read of this register. NOTE: Users can determine the current state of the “Network LoopCode Detection” by reading out the content of bit 3 within Register 0xNF05 2 Reserved - - This bit is not used 183 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 166: LIU CHANNEL CONTROL INTERRUPT STATUS REGISTER (LIUCCISR) HEX ADDRESS: 0X0FN6 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 RLOSIS_n RUR/ WC 0 Change of Receive LOS (Loss of Signal) Defect Condition Interrupt Status: This RESET-upon-READ bit indicates whether or not the “Change of the Receive LOS Defect Condition” Interrupt has occurred since the last read of this register. 0 = Indicates that the “Change of the Receive LOS Defect Condition” Interrupt has NOT occurred since the last read of this register. 1 - Indicates that the “Change of the Receive LOS Defect Condition” Interrupt has occurred since the last read of this register. NOTE: The user can determine the current state of the “Receive LOS Defect condition” by reading out the contents of Bit 1 (Receive LOS Defect Condition Status) within Register 0xNF05. 0 QRPDIS_n RUR/ WC 0 Change in Quasi-Random Pattern Detection Interrupt Status: This RESET-upon-READ bit indicates whether or not the “Change in QRSS Pattern Detection” Interrupt has occurred since the last read of this register. 0 = Indicates that the “Change in QRSS Pattern Detection” Interrupt has NOT occurred since the last read of this register. 1 = Indicates that the “Change in QRSS Pattern Detection” Interrupt has occurred since the last read of this register. This bit is set to a “1” every time when QRPD status bit (bit 0 of Register 0xNF05) has changed since the last read of this register. NOTE: Users can determine the current state of the “QRSS Pattern Detection” by reading out the content of bit 0 within Register 0xNF05 NOTE: Register 0xNF04, 0xNF05 and 0xNF06 only work if the LIU is placed in Single Rail mode. If done so, the Framer block must also be placed in Single Rail mode in Register 0xN101. TABLE 167: LIU CHANNEL CONTROL CABLE LOSS REGISTER (LIUCCCCR) BIT FUNCTION TYPE DEFAULT 7 Reserved RO 0 6 Reserved RO 0 5-0 CLOS[5:0] RO 0 HEX ADDRESS: 0X0FN7 DESCRIPTION-OPERATION Cable Loss [5:0]: These bits represent the six bit receive selective equalizer setting which is also a binary word that represents the cable attenuation indication within ±1dB. CLOS5_n is the most significant bit (MSB) and CLOS0_n is the least significant bit (LSB). 184 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 168: LIU CHANNEL CONTROL ARBITRARY REGISTER 1 (LIUCCAR1) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_Seg1 R/W 0 REV. 1.0.1 HEX ADDRESS: 0X0FN8 DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 1: These seven bits form the first of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). NOTE: Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. TABLE 169: LIU CHANNEL CONTROL ARBITRARY REGISTER 2 (LIUCCAR2) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_Seg2 R/W 0 HEX ADDRESS: 0X0FN9 DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 2 These seven bits form the second of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). NOTE: Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. TABLE 170: LIU CHANNEL CONTROL ARBITRARY REGISTER 3 (LIUCCAR3) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_seg3 R/W 0 HEX ADDRESS: 0X0FNA DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 3 These seven bits form the third of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). NOTE: Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. 185 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 171: LIU CHANNEL CONTROL ARBITRARY REGISTER 4 (LIUCCAR4) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_seg4 R/W 0 DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 4 These seven bits form the forth of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. TABLE 172: LIU CHANNEL CONTROL ARBITRARY REGISTER 5 (LIUCCAR5) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_seg5 R/W 0 FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6-0 Arb_seg6 R/W 0 HEX ADDRESS: 0X0FNC DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 5 These seven bits form the fifth of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. TABLE 173: LIU CHANNEL CONTROL ARBITRARY REGISTER 6 (LIUCCAR6) BIT HEX ADDRESS: 0X0FNB HEX ADDRESS: 0X0FND DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 6 These seven bits form the sixth of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. 186 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 174: LIU CHANNEL CONTROL ARBITRARY REGISTER 7 (LIUCCAR7) BIT FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6 Arb_seg7 R/W 0 FUNCTION TYPE DEFAULT 7 Reserved R/W 0 6 Arb_seg8 R/W 0 HEX ADDRESS: 0X0FNE DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 7 These seven bits form the seventh of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. TABLE 175: LIU CHANNEL CONTROL ARBITRARY REGISTER 8 (LIUCCAR8) BIT REV. 1.0.1 HEX ADDRESS: 0X0FNF DESCRIPTION-OPERATION Arbitrary Transmit Pulse Shape, Segment 8 These seven bits form the eight of the eight segments of the transmit shape pulse when the XRT86VX38 is configured in “Arbitrary Mode”. These seven bits represent the amplitude of the nth channel's arbitrary pulse in signed magnitude format with Bit 6 as the sign bit and Bit 0 as the least significant bit (LSB). Arbitrary mode is enabled by writing to the EQC[4:0] bits in register 0xNF00. 187 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 176: LIU GLOBAL CONTROL REGISTER 0 (LIUGCR0) HEX ADDRESS: 0X0FE0 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 SR R/W 0 Single Rail mode This bit must set to "1" for Single Rail mode to use LIU diagnotic features. The Framer section must be programmed as well in Register 0xN101. 0 - Dual Rail 1 - Single Rail 6 ATAOS R/W 0 Automatic Transmit All Ones Upon RLOS: This bit enables automatic transmission of All Ones Pattern upon detecting the Receive Loss of Signal (RLOS) condition. Once this bit is enabled, the Transmit T1 Framer Block will automatically transmit an All “Ones” data to the line for the channel that detects an RLOS condition. 0 = Disables the “Automatic Transmit All Ones” feature upon detecting RLOS 1 = Enables the “Automatic Transmit All Ones” feature upon detecting RLOS 5 RCLKE R/W 0 Receive Clock Data (Framer Bypass mode) 0 = RPOS/RNEG data is updated on the rising edge of RCLK 1 = RPOS/RNEG data is updated on the falling edge of RCLK 4 TCLKE R/W 0 Transmit Clock Data (Framer Bypass mode) 0 = TPOS/TNEG data is sampled on the falling edge of TCLK 1 = TPOS/TNEG data is sampled on the rising edge of TCLK 3 DATAP R/W 0 Data Polarity 0 = Transmit input and receive output data is active “High” 1 = Transmit input and receive output data is active “Low” 2 Reserved This Bit Is Not Used 188 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 176: LIU GLOBAL CONTROL REGISTER 0 (LIUGCR0) REV. 1.0.1 HEX ADDRESS: 0X0FE0 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 1 GIE R/W 0 Global Interrupt Enable: This bit allows users to enable or disable the global interrupt generation for all channels within the E1 LIU Block. Once this global interrupt is disabled, no interrupt will be generated to the Microprocessor Interrupt Pin even when the individual “source” interrupt status bit pulses ‘high’. If this global interrupt is enabled, users still need to enable the individual “source” interrupt in order for the E1 LIU Block to generate an interrupt to the Microprocessor pin. 0 - Disables the global interrupt generation for all channels within the E1 LIU Block. 1 - Enables the global interrupt generation for all channels within the E1 LIU Block. 0 SRESET R/W 0 Software Reset P Registers: This bit allows users to reset the XRT86VX38 device. Writing a “1” to this bit and keeping it at ’1’ for longer than 10µs initiates a device reset through the microprocessor interface. Once the XRT86VX38 is reset, all internal circuits are placed in the reset state except the microprocessor register bits. 0 = Disables software reset to the XRT86VX38 device. 1 = Enables software reset to the XRT86VX38 device. 189 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 177: LIU GLOBAL CONTROL REGISTER 1 (LIUGCR1) HEX ADDRESS: 0X0FE1 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 TxSYNC(Sect 13) R/W 0 G.703 Section 13 Transmit Pulse When this bit is set to ’1’, the LIU transmitter will send a T1 synchrnonous waveform as described in Section 13 of ITU-T G.703, except with frequency equal to 1.544MHz. This register bit takes priority over every other LIU setting on the transmit path. 0 = T1 pulse specified in EQC bits 1 = Section 13 Synchronous Pulse at 1.544MHz 6 RxSYNC(Sect 13) R/W 0 G.703 Section 13 Receiver When this bit is set to ’1’, the CDR block of the receiver is configured to accept a waveform as described in Section 13 of ITU-T G.703 except with frequency equal to 1.544MHz. 0 = Normal T1 (Equalizer Bit Settings - EQU[4:0]) 1 = Section 13 Synchronous Pulse at 1.544MHz 5-4 Gauge [1:0] R/W 00 Wire Gauge Selector [1:0]: This bit together with Guage0 bit (bit 4 within this register) are used to select the wire gauge size as shown in the table below. 3 Reserved 2 RXMUTE GAUGE1 GAUGE0 Wire Size 0 0 22 and 24 Gauge 0 1 22 Gauge 1 0 24 Gauge 1 1 26 Gauge This bit is not used R/W 0 Receive Output Mute: This bit permits the user to configure the Receive T1 Block to automatically pull its Recovered Data Output pins to GND anytime (and for the duration that) the Receive T1 LIU Block declares the LOS defect condition. In other words, if this feature is enabled, the Receive T1 LIU Block will automatically “mute” the Recovered data that is being routed to the Receive T1 Framer block anytime (and for the duration that) the Receive T1 LIU Block declares the LOS defect condition. 0 – Disables the “Muting upon LOS” feature. 1 – Enables the “Muting upon LOS” feature. NOTE: The receive clock is not muted when this feature is enabled. 190 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 177: LIU GLOBAL CONTROL REGISTER 1 (LIUGCR1) BIT FUNCTION 1 EXLOS 0 ICT TYPE DEFAULT REV. 1.0.1 HEX ADDRESS: 0X0FE1 DESCRIPTION-OPERATION Extended LOS Enable: This bit allows users to extend the number of zeros at the receive input before RLOS is declared. When Extended LOS is enabled, the Receive T1 LIU Block will declare RLOS condition when it receives 4096 number of consecutive zeros at the receive input. When Extended LOS is disabled, the Receive T1 LIU Block will declare RLOS condition when it receives 175 number of consecutive zeros at the receive input. 0 = Disables the Extended LOS Feature. 1 = Enables the Extended LOS Feature. R/W 0 In-Circuit-Testing Enable: This bit allows users to tristate the output pins of all channels for incircuit testing purposes. When In-Circuit-Testing is enabled, all output pins of the XRT86VX38 are “Tri-stated”. When In-Circuit-Testing is disabled, all output pins will resume to normal condition. 0 = Disables the In-Circuit-Testing Feature. 1 = Enables the In-Circuit-Testing Feature. TABLE 178: LIU GLOBAL CONTROL REGISTER 2 (LIUGCR2) HEX ADDRESS: 0X0FE2 BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7 Force to "0" R/W 0 Set to "0" 6-0 Reserved R/W 0 These Bits Are Not Used 191 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 179: LIU GLOBAL CONTROL REGISTER 3 (LIUGCR3) HEX ADDRESS: 0X0FE4 BIT FUNCTION TYPE DEFAULT 7-6 Reserved R/W 0 These Bits are Not Used. 5-4 MCLKn[1:0] R/W 00 Master T1 Output Clock Reference [1:0] These two bits allow users to select the programmable output clock rates for the MCLKnOUT pin, according to the table below. 3-0 Reserved R/W 0 DESCRIPTION-OPERATION MCLKNT1[1:0] CLOCK RATE OF THE T1MCLKNOUT OUTPUT PIN 00 1.544MHz 01 3.088MHz 10 6.176MHz 11 12.352MHz These Bits are Not Used. 192 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION TABLE 180: LIU GLOBAL CONTROL REGISTER 4 (LIUGCR4) BIT FUNCTION TYPE DEFAULT 7-4 Reserved R/W 0 3-0 CLKSEL[3:0] R/W 0001 REV. 1.0.1 HEX ADDRESS: 0X0FE9 DESCRIPTION-OPERATION Clock Select Input [3:0] These four bits allow users to select the programmable input clock rates for the MCLKIN input pin, according to the table below. CLKSEL[3:0] CLOCK RATE OF THE MCLKIN INPUT PIN 0000 2.048MHz 0001 1.544MHz 0010 - 0111 Reserved 1000 4.096MHz 1001 3.088MHz 1010 8.192MHz 1011 6.176MHz 1100 16.384MHz 1101 12.352MH 1110 2.048MHz 1111 1.544MHz NOTE: User must provide any one of the above clock frequencies to the MCLKIN input pin for the device to be functional. 193 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 TABLE 181: LIU GLOBAL CONTROL REGISTER 5 (LIUGCR5) HEX ADDRESS: 0X0FEA BIT FUNCTION TYPE DEFAULT DESCRIPTION-OPERATION 7-1 Reserved - 0 These bits are reserved 0 GCHIS0 RUR/ WC 0 Global Channel 0 Interrupt Status Indicator This Reset-Upon-Read bit field indicates whether or not an interrupt has occurred on Channel 0 within the XRT86VX38 device since the last read of this register. 0 = Indicates that No interrupt has occurred on Channel 0 within the XRT86VX38 device since the last read of this register. 1 = Indicates that an interrupt has occurred on Channel 0 within the XRT86VX38 device since the last read of this register. 194 XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 ORDERING INFORMATION PRODUCT NUMBER PACKAGE OPERATING TEMPERATURE RANGE XRT86VX38IB256 256 PIn Fine Pitch Ball Grid Array -40C to +85C XRT86VX38IB329 329 PIn Fine Pitch Ball Grid Array -40C to +85C PACKAGE DIMENSIONS FOR 256 PIN FINE PITCH BALL GRID ARRAY 256 Fine Pitch Ball Grid Array (17.0 mm x 17.0 mm, fpBGA) Rev. 1.00 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A1 corner A B C D E F G H D1 D J K L M N P R T D1 D (A1 corner feature is mfger option) Seating Plane A A1 b A2 e Note: The control dimension is in millimeter. SYMBOL A A1 A2 D D1 b e INCHES MIN MAX 0.058 0.070 0.013 0.017 0.045 0.053 0.661 0.677 0.591 BSC 0.020 0.024 0.039 BSC 195 MILLIMETERS MIN MAX 1.48 1.78 0.33 0.43 1.15 1.35 16.80 17.20 15.00 BSC 0.50 0.60 1.00 BSC XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 PACKAGE DIMENSIONS FOR 329 PIN FINE PITCH BALL GRID ARRAY 4 329 Fine Pitch Ball Grid Array (17.0 mm x 17.0 mm, fpBGA) Rev. 1.00 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 A1 corner A B C D E F G H J D K D1 L M N P R T U V W D1 D (A1 corner feature is mfger option) Seating Plane A A1 b A2 e Note: The control dimension is in millimeter. SYMBOL A A1 A2 D D1 b e INCHES MIN MAX 0.056 0.067 0.010 0.014 0.046 0.053 0.663 0.675 0.567 BSC 0.014 0.018 0.031 BSC 196 MILLIMETERS MIN MAX 1.43 1.71 0.26 0.36 1.17 1.35 16.85 17.15 14.40 BSC 0.36 0.46 0.80 BSC XRT86VX38 8-CHANNEL T1/E1/J1 FRAMER/LIU COMBO - T1 REGISTER DESCRIPTION REV. 1.0.1 P4. REVISION HISTORY REVISION # DATE 1.0.0 May 2009 1.0.1 June 15, 2009 DESCRIPTION Release of the XRT86VX38 T1 Register Description Datasheet. Update the packaging name to fpBGA, update applications and features lists. NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2009 EXAR Corporation Datasheet June 2009. Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. 197