FINISAR FTLF1323P1WTR

Finisar
Product Specification
OC-3 IR-1/STM S-1.1 RoHS Compliant Pluggable SFP Transceiver
FTLF1323P1xTR
PRODUCT FEATURES
•
Up to 155 Mb/s bi-directional
data links
•
Hot-pluggable SFP footprint
•
Built-in digital diagnostic functions
•
Uncooled Fabry-Perot 1310nm
laser transmitter
•
Duplex LC connector
•
RoHS compliant and lead-free
•
Metal enclosure, for lower EMI
• SONET OC-3 IR-1 / SDH STM S-1.1
•
Single 3.3V power supply
• SONET OC-3 SR / SDH STM I-1
•
Low power dissipation <700mW
typical
• Suitable for Fast Ethernet
•
Industrial operating temperature
range: -40°C to 85°C
APPLICATIONS
Finisar’s FTLF1323P1xTR Small Form Factor Pluggable (SFP) transceivers are
compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA)1.
They comply with SONET and SDH standards2 at OC-3 IR-1/STM S-1.1 and OC-3
SR/STM I-1, and are suitable for Fast Ethernet applications. Digital diagnostics
functions are available via the 2-wire serial bus specified in the SFP MSA. They are
RoHS compliant and lead-free per Directive 2002/95/EC3 and Finisar Application Note
AN-2038.
PRODUCT SELECTION
FTLF1323P1xTR
x
W
B
 Finisar Corporation December 2, 2005 Rev.A
Wide Extraction Bail
Narrow Extraction Bail
Page 1
Finisar
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
I.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Pin Descriptions
Symbol
VEET
TFAULT
TDIS
MOD_DEF(2)
MOD_DEF(1)
MOD_DEF(0)
Rate Select
LOS
VEER
VEER
VEER
RDRD+
VEER
VCCR
VCCT
VEET
TD+
TDVEET
Name/Description
Transmitter Ground (Common with Receiver Ground)
Transmitter Fault. Not supported.
Transmitter Disable. Laser output disabled on high or open.
Module Definition 2. Data line for Serial ID.
Module Definition 1. Clock line for Serial ID.
Module Definition 0. Grounded within the module.
No connection required
Loss of Signal indication. Logic 0 indicates normal operation.
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Ground (Common with Transmitter Ground)
Receiver Inverted DATA out. AC Coupled.
Receiver Non-inverted DATA out. AC Coupled.
Receiver Ground (Common with Transmitter Ground)
Receiver Power Supply
Transmitter Power Supply
Transmitter Ground (Common with Receiver Ground)
Transmitter Non-Inverted DATA in. AC Coupled.
Transmitter Inverted DATA in. AC Coupled.
Transmitter Ground (Common with Receiver Ground)
Ref.
1
2
3
3
3
4
5
1
1
1
1
1
1
Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.5V.
MOD_DEF(0) pulls line low to indicate module is plugged in.
4. Finisar FTLF1323P1xTR transceivers operate between OC-3 and 125 Mbit/s without active control.
5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage
between 2.0V and 3.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
Towards
Bezel
1
VeeT
2
TXFault
3
TX Disable
4
MOD-DEF(2)
5
MOD-DEF(1)
6
MOD-DEF(0)
7
Rate Select
8
LOS
9
VeeR
10
VeeR
VeeT
20
TD-
19
TD+
18
VeeT
17
VccT
16
VccR
15
VeeR
14
RD+
13
RD-
12
VeeR
11
Towards
ASIC
Pinout of Connector Block on Host Board
 Finisar Corporation December 2, 2005 Rev.A
Page 2
Finisar
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
II.
Absolute Maximum Ratings
Parameter
Maximum Supply Voltage
Storage Temperature
Case Operating Temperature
Relative Humidity
III.
Symbol
Vcc
TS
TOP
RH
Min
-0.5
-40
-40
0
Typ
Max
4.5
100
85
85
Unit
V
°C
°C
%
Ref.
1
Electrical Characteristics (TOP = -40 to 85 °C, VCC = 3.10 to 3.50 Volts)
Parameter
Supply Voltage
Supply Current
Transmitter
Input differential impedance
Single ended data input swing
Transmit Disable Voltage
Transmit Enable Voltage
Transmit Disable Assert Time
Receiver
Single ended data output swing
Data rise/fall time
LOS Fault
LOS Normal
Power Supply Rejection
Symbol
Vcc
Icc
Rin
Vin,pp
VD
VEN
Vout,pp
tr
VLOS fault
VLOS norm
PSR
Min
3.10
Typ
165
Max
3.50
300
Unit
V
mA
Ref.
2
1200
Vcc
Vee+ 0.8
10
Ω
mV
V
V
µs
mV
ps
V
V
mVpp
4
5
6
6
7
100
250
Vcc – 1.3
Vee
300
Vcc – 0.5
Vee
100
400
250
800
500
VccHOST
Vee+0.5
3
Notes:
1. Non condensing
2. AC coupled.
3. Or open circuit.
4. Into 100 ohm differential termination.
5. 20 – 80 %
6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
7. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5
MHz up to specified value applied through the power supply filtering network shown on page 23 of the
Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA), September 14, 2000.
 Finisar Corporation December 2, 2005 Rev.A
Page 3
Finisar
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
IV.
Optical Characteristics (TOP = -40 to 85 °C, VCC = 3.10 to 3.50 Volts)
Parameter
Transmitter
Output Opt. Pwr: 9/125 SMF
Optical Wavelength
Spectral Width
Optical Extinction Ratio
Optical Rise/Fall Time
Relative Intensity Noise
Generated Jitter (peak to peak)
Generated Jitter (rms)
Mask Margin
Receiver
Average Rx Sensitivity @ OC-3
Average Rx Sensitivity @ 125 Mb/s
Optical Center Wavelength
LOS De-Assert
LOS Assert
LOS Hysteresis
Symbol
Min
POUT
λ
σ
ER
tr/ tf
RIN
JTXp-p
JTXrms
-15
1261
Typ
Max
Unit
-8
1360
7.7
dBm
nm
nm
dB
ps
dB/Hz
UI
UI
1
dBm
dBm
nm
dBm
dBm
dB
4
4
8.2
500
-120
0.07
0.007
Ref.
2
3
3
20%
RSENS1
RSEN2
λC
LOSD
LOSA
-28
-28
1260
-8
-8
1600
-28
-45
0.5
Notes:
1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
2. Unfiltered, 20-80%
3. Jitter measurements taken using Agilent OMNIBERT 718 in accordance with GR-253.
4. With worst-case extinction ratio. Measured with a PRBS 223-1 test pattern.
 Finisar Corporation December 2, 2005 Rev.A
Page 4
Finisar
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
V.
General Specifications
Parameter
Data Rate
Bit Error Rate
Max. Supported Link Length on
9/125µm SMF @ OC-3
Symbol
BR
BER
LMAX5
Min
125
Typ
Max
155
10-12
15
Units
Ref.
Mb/sec 1
2
km
4
Notes:
1. Compliant with SONET and SDH at the following rates: OC-3 IR-1/STM S-1.1 and
OC-3 SR/STM I-1.
2. Tested with a PRBS 223-1 test pattern.
3. Attenuation of 0.55 dB/km is used for the link length calculations (per GR-253 CORE). Distances are
indicative only. Please refer to the Optical Specifications in Table IV to calculate a more accurate link
budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar 1310nm SFP transceivers have an industrial operating temperature range from
–40°C to +85°C case temperature.
Parameter
Case Operating Temperature
Storage Temperature
VII.
Symbol
Top
Tsto
Min
-40
-40
Typ
Max
85
100
Units
°C
°C
Ref.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations.
These products are certified by TÜV and CSA to meet the Class 1 eye safety
requirements of EN (IEC) 60825 and the electrical safety requirements of
EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
 Finisar Corporation December 2, 2005 Rev.A
Page 5
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
VIII. Digital Diagnostic Functions
Finisar FTLF1323P1xTR SFP transceivers support the 2-wire serial communication
protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in
the GBIC standard, with the same electrical specifications.
The standard SFP serial ID provides access to identification information that describes
the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic
monitoring interface, which allows real-time access to device operating parameters such
as transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory-set normal range.
The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a
2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic
monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally
defined serial ID memory map remains unchanged. The interface is identical to, and is
thus fully backward compatible with both the GBIC Specification and the SFP Multi
Source Agreement. The complete interface is described in Finisar Application Note
AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through a 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the
SFP transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod
Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with
SCL to mark the start and end of serial protocol activation. The memories are organized
as a series of 8-bit data words that can be addressed individually or sequentially.
For more information, please see the SFP MSA documentation1 or Finisar Application
Note AN-2030.
Digital diagnostics for the FTLF1323P1xTR are externally calibrated by default.
Please note that evaluation board FDB-1018 is available with Finisar ModDEMO
software that allows simple to use communication over the 2-wire serial interface.
 Finisar Corporation December 2, 2005 Rev.A
Page 6
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
IX.
Finisar
Mechanical Specifications
Finisar’s Small Form Factor Pluggable (SFP) transceivers are compatible with the
dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTLF1323P1BTR
 Finisar Corporation December 2, 2005 Rev.A
Page 7
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
Finisar
FTLF1323P1WTR
 Finisar Corporation December 2, 2005 Rev.A
Page 8
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
X.
Finisar
PCB Layout and Bezel Recommendations
 Finisar Corporation December 2, 2005 Rev.A
Page 9
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
 Finisar Corporation December 2, 2005 Rev.A
Finisar
Page 10
FTLF1323P1xTR Pluggable SFP Product Specification - December 2005
XI.
Finisar
References
1.
Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),
September 2000. Documentation is currently available at Finisar upon request.
2.
Bellcore GR-253 and ITU-T G.957 Specifications.
3.
Directive 2002/95/EC of the European Council Parliament and of the Council,
“on the restriction of the use of certain hazardous substances in electrical and
electronic equipment.” January 27, 2003.
XII.
For More Information
Finisar Corporation
1389 Moffett Park Drive
Sunnyvale, CA 94089-1133
Tel. 1-408-548-1000
Fax 1-408-541-6138
[email protected]
www.finisar.com
 Finisar Corporation December 2, 2005 Rev.A
Page 11