INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Package Dimensions NOTES : 1. All dimensions are in millimeters. 2. Tolerance is ± 0.25(0.010") unless otherwise specified DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 1 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Description A miniaturized receiver for infrared remote control and IR data transmission. PIN diode and preamplifier are assembled on lead frame. The epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the operation with high data rates and long distances. Features Photo detector and preamplifier in one package Internal band filter for PCM frequency Internal shielding against electrical field disturbance TTL and CMOS compatibility Output active low Small size package Special Features Supply voltage 5.5 V Short settling time after power on High envelope duty cycle can be received Enhanced immunity against disturbance from energy saving lamps Application AV instruments such as Audio, TV, VCR, CD, DVD, MD etc. Home appliances such as Air conditioner, Fan etc. The other equipments with wireless remote control. CATV set top boxes. Multi-media Equipment. Sensors and light barrier systems for long distances DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 2 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Block Diagram VS IN AGC ＆FILTER INPUT OUT us DEMODULATOR AGC/ATC＆DIGITAL CONTROL OSCILLATOR GND Application Circuit IRM cc DD 4.7u ≥2.4K uC GND GND Transmit Signal (Carrier Frequency=fo) IR Transmitter Output Wave Form μ μ Delay VOH Output Pulse Of Device Twl Twh DRAWING NO.: DS-27-01-0001 VOL DATE: 2004-08-31 Page: 3 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Data Transmission Rate, Vs=5V 5000 4000 3000 (bit/s) 2000 1500 1000 0 25.0 45.0 35.0 55.0 fo(KHz) 65.0 75.0 85.0 Illustration Of Used Terms 600us IN 1 600us 8 8 tDON tDOFF 8 600us 600us OUT ENVELOPE1 ENVELOPE2 ENVELOPE23 27600us/DATA WORD OUT DATA WORD TELEGRAM PAUSE DATA WORD t 27.6ms Trep=62ms DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 4 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Absolute Maximum Ratings : ( Ta = 25°C ) Symbol Parameter Ultra Condition Unit 5.5 V Vcc Supply Voltage Tstg Storage Temperature Range －25to 85 ℃ Topr Operating Temperature Range －25to 85 ℃ Tsol Soldering Temperature 255(Max 5sec) ℃ Lead Soldering Temperature ｛1.6mm（0.063inch）From Body｝250±5℃ For 3 Seconds. Electro-Optical Characteristics : ( Ta = 25℃) Symbol Parameter Condition Min. Typ. 4.5 5 Max. Unit Vcc Supply Voltage Icc Current Consumption λP Peak Emission Wavelength 940 nm fo B.P.F Center Frequency 38 KHz L Arrival Distance 0° 35 m ±45° 8 m Input signal=0 L-514EIR1C Voh H Level Output Voltage Vol L Level Output Voltage Twh H Level Output Pulse Width Burst Wave=600μs Twl L Level Output Pulse Width Period=1.2ms Output Form 30cm Over The Axis V 2.5 4.5 mA V 0.1 0.5 V 500 600 700 μs 500 600 700 μs Active Low Output Note 1.Distance between emitter & detector specifies maximum distance that output waveform satisfies the standard under the conditions below against the standard transmitter. Measuring place------Indoors without extreme reflection of light. Ambient light source------Detecting surface illumination shall be 200±50Lux under ordinary fluorescence lamp of no high frequency lighting. Standard transmitter------Burst wave indicated shall be arranged to 50mVp-p under the measuring circuit. Note 2. (Electro-optical chrematistics) shall be satisfied after leaving 2 hours in the normal temperature. DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 5 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Eemin/Ee-Rel.Responsivity po-Output Pulse Width(ms) Typical Characteristics（Ta=25℃） λ=940nm optical test signal,fig1 f/fo-Relative Frequency Ee-Irradiance(mW/㎡) Pulse Diagram Eemin-Threshold Irradiance(mW/㎡) 1 λ=940nm optical test signal,fig3 Ee-Irradiance(mW/㎡) λ=940nm E-Ambient DC Irradiance(mW/㎡) Pulse Diagram 10KHz 1KHz 100KHz △Vsrms-AC Voltage on DC Supply Voltage(mV) DRAWING NO.: DS-27-01-0001 4 Eemin-Threshold Irradiance(mW/㎡) Eemin-Threshold Irradiance(mW/㎡) 2 f=fo±5% △f(3dB)=fo/10 Tamb-Ambient Temperature(℃) DATE: 2004-08-31 Page: 6 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Eemin-Threshold Irradiance(mW/㎡) S(λ)rel-Relative Spectral Sensitivity Typical Characteristics（Ta=25℃） λ-Wavelength(nm) MAX.Envelope Duty Cycle Ee-Field Strength of Disturbance(KV/m) Burst Length (number of cycles/burst) DRAWING NO.: DS-27-01-0001 drel-Relative transmission Distance DATE: 2004-08-31 Page: 7 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Operation Notes(Standard Condition) IR CODE IR Receiver PL-IRM0101-3 Best Application Suitable Grundig Code @ Nec Code @ Rc5 Code @ Rc6 Code @ Rcmm Code @ Not Recommended Rcs-80 Code @ R-2000 Code @ Rca Code @ Sharp Code @ Sony 12bit Code @ Sony 15bit Code @ Zenith Code @ High Data Rate Code Disturbance Suppression Note: @ @ @: Best For Application Overview Of The Disturbance Suppression Behavior Disturbance Lamp IR Receiver PL-IRM0101-3 From Most Used Fluorescent Lamps (With Switched Supply) Best Suppression From Most Used Fluorescent Lamps (With Direct Line Supply) Best Suppression From Most Used Fluorescent Lamps (With Strong Ballast) Possibility Of Disturbance Pulses DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 8 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Static-Electricity Resistant Packaging Cautions 1. 2. 3. 4. 5. Store and use where there is no force causing transformation or change in quality. Store and use where there is no corrosive gas or sea (salt) breeze. Store and use where there is no extreme humidity. Solder the lead-pin within the condition of ratings. After soldering do not add extra force. Do not wash this device. Wipe the stains of diode side with a soft cloth. You can use the solvent, ethyl alcohol or methyl alcohol or propylene only. 6. To prevent static electricity damage to the Pre-AMP make sure that the human body, the soldering iron is connected to ground before using. 7. Put decoupling device between Vcc and GND for reduce the noise from power supply line. 8. The performance of remote-control system depends on environments condition and ability of peripheral parts. Customer should evaluate the performance as total system in those conditions after system up with components such as commander and this receiver module. 9. This device is not design to endure radioactive rays and heavily charged particles. 10. In case where any trouble or questions arise, all parties agree to make full discussion covering the said problem. DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 9 INFRARED REMOTE CONTROL RECEIVER MODULE PL-IRM0101-3 REV: B / 0 Reliability Test Item And Condition Test Items Test Conditions Failure Judgment Criteria Samples (n) Defectives(c) High Temperature +85℃ 240hrs Storage N=22 C=0 Low Temperature -25℃ 240hrs Storage N=22 C=0 Temperature Cycle -55℃--------+105℃ (10min) (10min) 20cycles High Temperature 85℃ 85%RH 240hrs High Humidity Soldering Heat Performance test requirement and criteria given in page 6 should be satisfied. N=22 C=0 N=22 C=0 N=22 C=0 255±5℃ 10s Others: The appearance and specifications of the product may be modified for improvement without notice. DRAWING NO.: DS-27-01-0001 DATE: 2004-08-31 Page: 10