HYNIX HYMD512G726B4-H

128Mx72 bits
Low Profile Registered DDR SDRAM DIMM
HYMD512G726B(L)4M-M/K/H/L
DESCRIPTION
Preliminary
Hynix HYMD512G726B(L)4M-M/K/H/L series is low profile registered 184-pin double data rate Synchronous DRAM
Dual In-Line Memory Modules (DIMMs) which are organized as 128M x 72 high-speed memory arrays.
HYMD512G726B(L)4M-M/K/H/L series consists of eighteen 128M x 4 DDR SDRAM in 400mil TSOP II packages on a
184pin glass-epoxy substrate. Hynix HYMD512G726B(L)4M-M/K/H/L series provide a high performance 8-byte interface in 5.25" width form factor of industry standard. It is suitable for easy interchange and addition.
Hynix HYMD512G726B(L)4M-M/K/H/L series is designed for high speed of up to 133MHz and offers fully synchronous
operations referenced to both rising and falling edges of differential clock inputs. While all addresses and control inputs
are latched on the rising edges of the clock, Data, Data strobes and Write data masks inputs are sampled on both rising and falling edges of it. The data paths are internally pipelined and 2-bit prefetched to achieve very high bandwidth.
All input and output voltage levels are compatible with SSTL_2. High speed frequencies, programmable latencies and
burst lengths allow variety of device operation in high performance memory system.
Hynix HYMD512G726B(L)4M-M/K/H/L series incorporates SPD(serial presence detect). Serial presence detect function
is implemented via a serial 2,048-bit EEPROM. The first 128 bytes of serial PD data are programmed by Hynix to identify DIMM type, capacity and other the information of DIMM and the last 128 bytes are available to the customer.
FEATURES
•
1GB (128M x 72) Low Profile Registered DDR DIMM
based on 128M x 4 DDR SDRAM
•
Fully differential clock operations (CK & /CK) with
100/133MHz
•
JEDEC Standard 184-pin dual in-line memory module
(DIMM)
•
Programmable CAS Latency 2 / 2.5 supported
•
•
Error Check Correction (ECC) Capability
Programmable Burst Length 2 / 4 / 8 with both
sequential and interleave mode
•
Registered inputs with one-clock delay
•
tRAS Lock-out function supported
•
Phase-lock loop (PLL) clock driver to reduce loading
•
Internal four bank operations with single pulsed RAS
•
2.5V +/- 0.2V VDD and VDDQ Power supply
•
Auto refresh and self refresh supported
•
All inputs and outputs are compatible with SSTL_2
interface
•
8192 refresh cycles / 64ms
ORDERING INFORMATION
Part No.
Power Supply
HYMD512G726B(L)4-M
HYMD512G726B(L)4-K
HYMD512G726B(L)4-H
HYMD512G726B(L)4-L
Clock Frequency
Interface
Form Factor
SSTL_2
184pin Registered DIMM
5.25 x 1.2 x 0.15 inch
133MHz (*DDR266 2-2-2)
VDD=2.5V
VDDQ=2.5V
133MHz (*DDR266A)
133MHz (*DDR266B)
125MHz (*DDR200)
* JEDEC Defined Specifications compliant
This document is a general product description and is subject to change without notice. Hynix Semiconductor does not assume any
responsibility for use of circuits described. No patent licenses are implied.
Rev. 0.1 / June 2004
1
HYMD512G726B(L)4M-M/K/H/L
PIN DESCRIPTION
Pin
Pin Description
Pin
CK0, /CK0
Differential Clock Inputs
VDDQ
Pin Description
DQs Power Supply
CS0
Chip Select Input
VSS
Ground
CKE0
Clock Enable Input
VREF
Reference Power Supply
/RAS, /CAS, /WE
Commend Sets Inputs
VDDSPD
Power Supply for SPD
A0 ~ A12
Address
SA0~SA2
E2PROM Address Inputs
BA0, BA1
Bank Address
SCL
E2PROM Clock
DQ0~DQ63
Data Inputs/Outputs
SDA
E2PROM Data I/O
CB0~CB7
Data Strobe Inputs/Outputs
WP
Write Protect Flag
DQS0~DQS17
Data Strobe Inputs/Outputs
VDDID
VDD Identification Flag
DM0~7
Data-in Mask
DU
Do not Use
VDD
Power Supply
NC
No Connection
/RESET
Reset Enable
FETEN
FET Enable
PIN ASSIGNMENT
Pin
Name
Pin
Name
Pin
Name
Pin
Name
Pin
Name
Pin
1
VREF
32
A5
62
VDDQ
93
VSS
124
VSS
154
Name
/RAS
2
DQ0
33
DQ24
63
/WE
94
DQ4
125
A6
155
DQ45
VDDQ
3
VSS
34
VSS
64
DQ41
95
DQ5
126
DQ28
156
4
DQ1
35
DQ25
65
/CAS
96
VDDQ
127
DQ29
157
/CS0
5
DQS0
36
DQS3
66
VSS
97
DQS9
128
VDDQ
158
/CS1*
6
DQ2
37
A4
67
DQS5
98
DQ6
129
DQS12
159
DM5
7
VDD
38
VDD
68
DQ42
99
DQ7
130
A3
160
VSS
8
DQ3
39
DQ26
69
DQ43
100
VSS
131
DQ30
161
DQ46
DQ47
9
NC
40
DQ27
70
VDD
101
NC
132
VSS
162
10
/RESET
41
A2
71
NC
102
NC
133
DQ31
163
NC
11
VSS
42
Vss
72
DQ48
103
A13
134
CB4
164
VDDQ
12
DQ8
43
A1
73
DQ49
104
VDDQ
135
CB5
165
DQ52
13
DQ9
44
CB0
74
VSS
105
DQ12
136
VDDQ
166
DQ53
14
DQS1
45
CB1
75
DU
106
DQ13
137
CK0
167
NC, FETEN*
15
VDDQ
46
VDD
76
DU
107
DQS10
138
/CK0
168
VDD
16
DU
47
DQS8
77
VDDQ
108
VDD
139
VSS
169
DM6
17
DU
48
A0
78
DQS6
109
DQ14
140
DQS17
170
DQ54
18
VSS
49
CB2
79
DQ50
110
DQ15
141
A10
171
DQ55
19
DQ10
50
VSS
80
DQ51
111
CKE1*
142
CB6
172
VDDQ
20
DQ11
51
CB3
81
VSS
112
VDDQ
143
VDDQ
173
NC
21
CKE0
52
BA1
82
VDDID
113
BA2*
144
CB7
174
DQ60
22
VDDQ
83
DQ56
114
DQ20
175
DQ61
23
DQ16
53
DQ32
84
DQ57
115
A12
145
VSS
176
VSS
24
DQ17
54
VDDQ
85
VDD
116
VSS
146
DQ36
177
DM7
25
DQS2
55
DQ33
86
DQS7
117
DQ21
147
DQ37
178
DQ62
26
VSS
56
DQS4
87
DQ58
118
A11
148
VDD
179
DQ63
27
A9
57
DQ34
88
DQ59
119
DQS11
149
DQS13
180
VDDQ
28
DQ18
58
VSS
89
VSS
120
VDD
150
DQ38
181
SA0
29
A7
59
BA0
90
WP
121
DQ22
151
DQ39
182
SA1
30
VDDQ
60
DQ35
91
SDA
122
A8
152
VSS
183
SA2
31
DQ19
61
DQ40
92
SCL
123
DQ23
153
DQ44
184
VDDSPD
Key
key
* These are not used on this module but may be used for other module in 184pin DIMM family
Rev. 0.1 / June 2004
2
HYMD512G726B(L)4M-M/K/H/L
FUNCTIONAL BLOCK DIAGRAM
VSS
/RS0
DQS0
DM0/DQS9
DQ0
DQ1
DQ2
DQ3
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ8
DQ9
DQ10
DQ11
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ16
DQ17
DQ18
DQ19
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ24
DQ25
DQ26
DQ27
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ32
DQ33
DQ34
DQ35
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ40
DQ41
DQ42
DQ43
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ48
DQ49
DQ50
DQ51
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DM
D0
DQS1
DQ4
DQ5
DQ6
DQ7
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ12
DQ13
DQ14
DQ15
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ20
DQ21
DQ22
DQ23
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ28
DQ29
DQ30
DQ31
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ36
DQ37
DQ38
DQ39
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ44
DQ45
DQ46
DQ47
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DQ52
DQ53
DQ54
DQ55
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DM
D0
D9
DM1/DQS10
DM
D1
DQS2
DM
D0
D10
DM2/DQS11
DM
D2
DQS3
DM
D0
D11
DM3/DQS12
DM
D3
DQS4
DM
D0
D12
DM4/DQS13
DM
D4
DQS5
DM
D0
D13
DM5/DQS14
DM
D5
DQS6
DM
D0
D14
DM6/DQS15
DM
D6
DQS7
D0
D15
DM7/DQS16
DQS
I/O0
I/O1
I/O2
I/O3
DQ56
DQ57
DQ58
DQ59
/CS
DM
DQ60
DQ61
DQ62
DQ63
D7
DQS8
DQS
I/O0
I/O1
I/O2
I/O3
/CS
DM
DQS
I/O0
I/O1
I/O2
I/O3
/S0
R
E
G
I
S
T
E
R
BA0-BA1
A0-A12
/RAS
/CAS
CKE
/W E
PCK
/PCK
/CS
DM
D8
CB4
CB5
CB6
CB7
/RS->/CS : SDRAMs D0-D17
RBA0-RBA1-> : BA0->BA1 : SDRAMs D0-D17
RA0-RA12-> : A0->A12 : SDRAMs D0-D17
/RRAS->/RAS : SDRAMs D0-D17
/RCAS->/CAS : SDRAMs D0-D17
RCKEA->CKE : SDRAMs D0-D17
/RW E->W E : SDRAMs D0-D17
DQS
I/O0
I/O1
I/O2
I/O3
VDDQ
DO-D8
VDD
DO-D8
VREF
DO-D8
VSS
DO-D8
Strap:see Note 4
VDDID
D0
D16
Serial PD
DM8/DQS17
CB0
CB1
CB2
CB3
Serial PD
VDDSPD
DM
/CS
D0
D17
DM
SCL
SDA
WP
A0
A1
A2
SA0 SA1 SA2
Note :
1. DQ-to-I/O wiring may be changed within a byte.
2. DQ/DQS/DM/CKE/S relationships must be
maintained as shown.
3. DQ/DQS resistors should be 22 Ohms.
4. V DDID strap connections (for memory device V DD , V DDQ ) :
STRAP OUT (OPEN) : V DD = V DDQ
STRAP IN (V SS ) : V DD ≠ V DDQ
5. Address and control resistors should be 22 Ohms.
/RESET
CKO, /CKO------PLL*
* W ire per Clock Loading Table /W iring Diagram
Rev. 0.1 / June 2004
3
HYMD512G726B(L)4M-M/K/H/L
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Operating Temperature (Ambient)
TA
0 ~ +70
o
C
Storage Temperature
TSTG
-55 ~ +125
o
C
Voltage on Any Pin relative to VSS
VIN, VOUT
-0.5 ~ 3.6
V
Voltage on VDD relative to VSS
VDD
-0.5 ~ 3.6
V
Voltage on VDDQ relative to VSS
VDDQ
-0.5 ~ 3.6
V
Output Short Circuit Current
IOS
50
mA
Power Dissipation
PD
1.0 x # of Components
W
Soldering Temperature Þ Time
TSOLDER
260 / 10
oC
/ Sec
Note : Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS= 0V)
Parameter
Symbol
Min
Typ.
Max
Unit
Power Supply Voltage
VDD
2.3
2.5
2.7
V
Power Supply Voltage
VDDQ
2.3
2.5
2.7
V
Input High Voltage
VIH
VREF + 0.15
-
VDDQ + 0.3
V
Input Low Voltage
VIL
-0.3
-
VREF - 0.15
V
Termination Voltage
VTT
VREF - 0.04
VREF
VREF + 0.04
V
Reference Voltage
VREF
0.49*VDDQ
0.5*VDDQ
0.51*VDDQ
V
Note
1
2
3
Note :
1. VDDQ must not exceed the level of VDD.
2. VIL (min) is acceptable -1.5V AC pulse width with < 5ns of duration.
3. The value of VREF is approximately equal to 0.5VDDQ.
AC OPERATING CONDITIONS (TA=0 to 70 oC, Voltage referenced to VSS = 0V)
Parameter
Symbol
Input High (Logic 1) Voltage, DQ, DQS and DM signals
VIH(AC)
Input Low (Logic 0) Voltage, DQ, DQS and DM signals
VIL(AC)
Input Differential Voltage, CK and /CK inputs
VID(AC)
Input Crossing Point Voltage, CK and /CK inputs
VIX(AC)
Min
Max
VREF + 0.31
Unit
Note
V
VREF - 0.31
V
0.7
VDDQ + 0.6
V
1
0.5*VDDQ-0.2
0.5*VDDQ+0.2
V
2
Note :
1. VID is the magnitude of the difference between the input level on CK and the input on /CK.
2. The value of VIX is expected to equal 0.5*V DDQ of the transmitting device and must track variations in the DC level of the same.
Rev. 0.1 / June 2004
4
HYMD512G726B(L)4M-M/K/H/L
AC OPERATING TEST CONDITIONS (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Value
Unit
Reference Voltage
VDDQ x 0.5
V
Termination Voltage
VDDQ x 0.5
V
AC Input High Level Voltage (VIH, min)
VREF + 0.31
V
AC Input Low Level Voltage (VIL, max)
VREF - 0.31
V
Input Timing Measurement Reference Level Voltage
VREF
V
Output Timing Measurement Reference Level Voltage
VTT
V
Input Signal maximum peak swing
1.5
V
Input minimum Signal Slew Rate
1
V/ns
Termination Resistor (RT)
50
Ω
Series Resistor (RS)
25
Ω
Output Load Capacitance for Access Time Measurement (CL)
30
pF
Rev. 0.1 / June 2004
5
HYMD512G726B(L)4M-M/K/H/L
CAPACITANCE (TA=25oC, f=100MHz )
Parameter
Pin
Symbol
Min
Max
Unit
Input Capacitance
A0 ~ A12, BA0, BA1
CIN1
8
12
pF
Input Capacitance
/RAS, /CAS, /WE
CIN2
8
12
pF
Input Capacitance
CKE0
CIN3
8
12
pF
Input Capacitance
CS0
CIN4
8
12
pF
Input Capacitance
CK0, /CK0
CIN5
8
14
pF
Data Input / Output Capacitance
DQ0 ~ DQ63, DQS0 ~ DQS17
CIO1
7
12
pF
Data Input / Output Capacitance
CB0 ~ CB7
CIO2
7
12
pF
Note :
1. VDD = min. to max., VDDQ = 2.3V to 2.7V, VODC = VDDQ/2, VOpeak-to-peak = 0.2V
2. Pins not under test are tied to GND.
3. These values are guaranteed by design and are tested on a sample basis only.
OUTPUT LOAD CIRCUIT
V TT
R T =50Ω
Output
Zo=50Ω
V REF
C L=30pF
Rev. 0.1 / June 2004
6
HYMD512G726B(L)4M-M/K/H/L
DC CHARACTERISTICS I (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Parameter
Input Leakage
Current
Add, CMD, /CS,
/CKE
Symbol
Min.
Max
-2
2
-4
4
ILI
CK, /CK
Unit
Note
uA
1
Output Leakage Current
ILO
-5
5
uA
2
Output High Voltage
VOH
VTT + 0.76
-
V
IOH = -15.2mA
Output Low Voltage
VOL
-
VTT - 0.76
V
IOL = +15.2mA
Note :
1. VIN = 0 to 3.6V, All other pins are not tested under VIN =0V
2. DOUT is disabled, VOUT=0 to 2.7V
3. These values are device characteristics.
Rev. 0.1 / June 2004
7
HYMD512G726B(L)4M-M/K/H/L
DC CHARACTERISTICS II (TA=0 to 70oC, Voltage referenced to VSS = 0V)
Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2)
Parameter
Symbol
Speed
Test Condition
-M
-K
-H
-L
Unit Note
Operating Current
IDD0
One bank; Active - Precharge ; tRC=tRC(min);
tCK= tCK(min) ; DQ,DM and DQS inputs changing
twice per clock cycle ; address and control inputs
changing once per clock cycle
Operating Current
IDD1
One bank ; Active - Read - Precharge ; Burst Length
= 2 ; tRC=tRC(min); tCK= tCK(min) ; address and
control inputs changing once per clock cycle
Precharge Power
Down Standby Current
IDD2P
All banks idle ; Power down mode ; CKE= Low,
tCK= tCK(min)
830
mA
Idle Standby Current
IDD2F
/CS = High, All banks idle ; tCK= tCK(min) ; CKE =
High ; address and control inputs changing once per
clock cycle. VIN = VREF for DQ, DQS and DM
1280
mA
Active Power Down
Standby Current
IDD3P
One bank active ; Power down mode ; CKE= Low,
tCK= tCK(min)
866
mA
Active Standby Current
IDD3N
/CS= HIGH; CKE = HIGH; One bank; ActivePrecharge; tRC = tRAS(max); tCK = t CK (max);
DQ, DM and DQS inputs changing twice per clock
cycle; Address and other control inputs changing
once per clock cycle
1370
mA
Operating Current
IDD4R
Burst = 2 ; Reads; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK= tCK (min); IOUT = 0mA
4250
3710
mA
IDD4W
Burst = 2; Writes; Continuous burst; One bank
active; Address and control inputs changing once
per clock cycle; tCK = tCK (min); DQ, DM, and DQS
inputs changing twice per clock cycle
4250
3710
mA
5030
4670
mA
Operating Current
Auto Refresh Current
IDD5
tRC = tRFC(min) - 8*tCK for DDR200 at 100Mhz,
10*tCK for DDR266A & DDR266B at 133Mhz;
distributed refresh
Self Refresh Current
IDD6
CKE =< 0.2V; External clock on;
tCK = tCK(min)
Operating Current Four Bank Operation
IDD7
Four bank interleaving with BL=4 Refer to the
following page for detailed test condition
Rev. 0.1 / June 2004
2990
2810
2450
mA
3530
3350
3170
mA
Normal
440
mA
Low Power
395
mA
7490
6050
mA
8
HYMD512G726B(L)4M-M/K/H/L
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2)
-M
Parameter
-K
H
-L
Symbol
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Row Cycle Time
tRC
60
-
65
-
65
-
70
-
ns
Auto Refresh Row Cycle Time
tRFC
75
-
75
-
75
-
80
-
ns
Row Active Time
tRAS
45
120K
45
120K
45
120K
50
120K
ns
Active to Read with Auto Precharge
Delay
tRAP
tRCD or
tRPmin
-
tRCD or
tRPmin
-
tRCD or
tRPmin
-
tRCD or
tRPmin
-
ns
Row Address to Column Address
Delay
tRCD
15
-
20
-
20
-
20
-
ns
Row Active to Row Active Delay
tRRD
15
-
15
-
15
-
15
-
ns
Column Address to Column Address
Delay
tCCD
1
-
1
-
1
-
1
-
CK
Row Precharge Time
tRP
15
-
20
-
20
-
20
-
ns
Write Recovery Time
tWR
15
-
15
-
15
-
15
-
ns
Write to Read Command Delay
tWTR
1
-
1
-
1
-
1
-
CK
Auto Precharge Write Recovery +
Precharge Time
tDAL
(tWR/
tCK)
+
(tRP/tCK)
-
(tWR/tCK)
+
(tRP/tCK)
(tWR/tCK)
+
(tRP/tCK)
-
(tWR/tCK)
+
(tRP/tCK)
7.5
12
7.5
12
7.5
12
8
12
7.5
12
10
12
10
12
10
12
System Clock Cycle
Time
CL = 2.5
CL = 2
tCK
CK
Note
16
15
ns
Clock High Level Width
tCH
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
CK
Clock Low Level Width
tCL
0.45
0.55
0.45
0.55
0.45
0.55
0.45
0.55
CK
Data-Out edge to Clock edge Skew
tAC
-0.7
0.7
-0.7
0.7
-0.7
0.7
-0.7
0.7
ns
DQS-Out edge to Clock edge Skew
tDQSCK
-0.7
0.7
-0.7
0.7
-0.7
0.7
-0.7
0.7
ns
DQS-Out edge to Data-Out edge
Skew
tDQSQ
-
0.5
0.5
-
0.5
0.6
ns
Data-Out hold time from DQS
tQH
tHP
-tQHS
-
tHP
-tQHS
-
tHP
-tQHS
-
tHP
-tQHS
-
ns
1, 10
Clock Half Period
tHP
min
(tCL,tCH)
-
min
(tCL,tCH)
-
min
(tCL,tCH)
-
min
(tCL,tCH)
-
ns
1,9
tQHS
-
0.75
-
0.75
-
0.75
-
0.75
ns
10
Data-out high-impedance window
from CK, /CK
tHZ
-0.75
0.75
-0.75
0.75
-0.75
0.75
-0.8
0.8
ns
17
Data-out low-impedance window
from CK, /CK
tLZ
-0.75
0.75
-0.75
0.75
-0.75
0.75
-0.8
0.8
ns
17
Input Setup Time (fast slew rate)
tIS
0.9
-
0.9
-
0.9
-
1.1
-
ns
2,3,5,6
Input Hold Time (fast slew rate)
tIH
0.9
-
0.9
-
0.9
-
1.1
-
ns
2,3,5,6
Data Hold Skew Factor
Rev. 0.1 / June 2004
9
HYMD512G726B(L)4M-M/K/H/L
AC CHARACTERISTICS (AC operating conditions unless otherwise noted)
- continued -
Bin Sort :M(DDR266(2-2-2),K(DDR266A@CL=2) H(DDR266B@CL=2.5),L(DDR200@CL=2)
-M
Parameter
-K
H
-L
Symbol
Min
Max
Min
Max
Min
Max
Min
Max
Unit
Note
Input Setup Time (slow slew rate)
tIS
1.0
-
1.0
-
1.0
-
1.1
-
ns
2,4,5,6
Input Hold Time (slow slew rate)
tIH
1.0
-
1.0
-
1.0
-
1.1
-
ns
2,4,5,6
tIPW
2.2
-
2.2
-
2.2
-
2.5
-
ns
6
Write DQS High Level Width
tDQSH
0.35
-
0.35
-
0.35
-
0.35
-
CK
Write DQS Low Level Width
tDQSL
0.35
-
0.35
-
0.35
-
0.35
-
CK
Clock to First Rising edge of DQS-In tDQSS
0.75
1.28
0.75
1.25
0.75
1.25
0.75
1.25
CK
Data-In Setup Time to DQS-In
(DQ & DM)
tDS
0.5
0.5
0.5
0.6
ns
Data-in Hold Time to DQS-In
(DQ & DM)
tDH
0.5
0.5
0.5
0.6
ns
DQ & DM Input Pulse Width
tDIPW
1.75
1.75
1.75
2
ns
Read DQS Preamble Time
tRPRE
0.9
1.1
0.9
1.1
0.9
1.1
0.9
1.1
CK
Read DQS Postamble Time
tRPST
0.4
0.6
0.4
0.6
0.4
0.6
0.4
0.6
CK
Write DQS Preamble Setup Time
tWPRES
0
0
0
0
CK
Write DQS Preamble Hold Time
tWPREH
0.25
0.25
0.25
0.25
CK
Write DQS Postamble Time
tWPST
0.4
Mode Register Set Delay
tMRD
2
2
2
2
CK
tXSC
200
200
200
200
CK
Input Pulse Width
Exit self refresh to Any Executable
Command
Average Periodic Refresh Interval
0.6
tREFI
7.8
0.4
0.6
7.8
0.4
0.6
7.8
0.4
0.6
7.8
6,7,11~
13
6
CK
8
us
Note :
1.
This calculation accounts for tDQSQ(max), the pulse width distortion of on-chip circuit and jitter.
2.
Data sampled at the rising edges of the clock : A0~A12, BA0~BA1, CKE, /CS, /RAS, /CAS, /WE.
3.
For command/address input slew rate >=1.0V/ns
4.
For command/address input slew rate >=0.5V/ns and <1.0V/ns
This derating table is used to increase tIS/tIH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Input Setup / Hold Slew-rate
Delta tIS
Delta tIH
V/ns
ps
ps
0.5
0
0
0.4
+50
0
0.3
+100
0
5.
CK, /CK slew rates are >=1.0V/ns
6.
These parameters guarantee device timing, but they are not necessarily tested on each device, and they may be guaranteed by
design or tester correlation
7.
Data latched at both rising and falling edges of Data Strobes(LDQS/UDQS) : DQ, LDM/UDM.
Rev. 0.1 / June 2004
10
HYMD512G726B(L)4M-M/K/H/L
8. Minimum of 200 cycles of stable input clocks after Self Refresh Exit command, where CKE is held high, is required to complete Self
Refresh Exit and lock the internal DLL circuit of DDR SDRAM
9. Min (tCL, tCH) refers to the smaller of the actual clock low time and the actual clock high time as provided to the device
(i.e. this value can be greater than the minimum specification limits for tCL and tCH).
10. tHP = minimum half clock period for any given cycle and is defined by clock high or clock low (tCH, tCL). tQHS consists of
tDQSQmax, the pulse width distortion of on-chip clock circuits, data pin to pin skew and output pattern effects and p-channel
to n-channel variation of the output drivers.
11.This derating table is used to increase tDS/tDH in case where the input slew-rate is below 0.5V/ns.
Input Setup / Hold Slew-rate Derating Table.
Input Setup / Hold Slew-rate
Delta tDS
Delta tDH
V/ns
ps
ps
0.5
0
0
0.4
+75
+75
0.3
+150
+150
12. I/O Setup/Hold Plateau Derating. This derating table is used to increase tDS/tDH in case where the input level is flat below VREF
+/-310mV for a duration of up to 2ns.
I/O Input Level
Delta tDS
Delta tDH
mV
ps
ps
+280
+50
+50
13. I/O Setup/Hold Delta Inverse Slew Rate Derating. This derating table is used to increase tDS/tDH in case where the DQ and DQS
slew rates differ. The Delta Inverse Slew Rate is calculated as (1/SlewRate1)-(1/SlewRate2). For example, if slew rate 1 = 0.5V/ns
and Slew Rate2 = 0.4V/n then the Delta Inverse Slew Rate = -0.5ns/V.
(1/SlewRate1)-(1/SlewRate2)
Delta tDS
Delta tDH
ns/V
ps
ps
0
0
0
+/-0.25
+50
+50
+/- 0.5
+100
+100
14. DQS, DM and DQ input slew rate is specified to prevent double clocking of data and preserve setup and hold times. Signal transi
tions through the DC region must be monotonic.
15. tDAL = (tDPL / tCK ) + (tRP / tCK ). For each of the terms above, if not already an integer, round to the next highest integer. tCK
is equal to the actual system clock cycle time.
Example: For DDR266B at CL=2.5 and tCK = 7.5 ns,
tDAL = (15 ns / 7.5 ns) + (20 ns / 7.5 ns) = (2.00) + (2.67)
Round up each non-integer to the next highest integer: = (2) + (3), tDAL = 5 clock
16. For the parts which do not has internal RAS lockout circuit, Active to Read with Auto precharge delay should be
tRAS - BL/2 x tCK2.
Rev. 0.1 / June 2004
11
HYMD512G726B(L)4M-M/K/H/L
SIMPLIFIED COMMAND TRUTH TABLE
A10/
AP
Command
CKEn-1
CKEn
/CS
/RAS
/CAS
/WE
Extended Mode Register Set
H
X
L
L
L
L
OP code
1,2
Mode Register Set
H
X
L
L
L
L
OP code
1,2
H
X
X
X
H
X
X
1
L
H
H
H
Device Deselect
No Operation
Bank Active
H
X
L
L
H
H
H
X
L
H
L
H
ADDR
RA
Read
BA
V
L
CA
Read with Autoprecharge
1
1,3
L
H
X
L
H
L
L
CA
Write with Autoprecharge
1
V
H
Precharge All Banks
H
X
L
L
H
L
Precharge selected Bank
1
V
H
Write
Note
1,4
H
X
1,5
L
V
1
X
Read Burst Stop
H
X
L
H
H
L
X
1
Auto Refresh
H
H
L
L
L
H
X
1
Entry
H
L
L
L
L
H
H
X
X
X
Exit
L
H
L
H
H
H
H
X
X
X
L
H
H
H
Self Refresh
Precharge
Power Down
Mode
Active Power
Down Mode
Entry
H
1
X
1
1
L
1
X
Exit
Entry
Exit
L
H
L
H
X
X
X
1
L
H
H
H
1
H
X
X
X
1
L
V
V
V
H
L
H
X
X
1
1
( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation )
Note :
1. DM states are Don’t Care. Refer to below Write Mask Truth Table.
2. OP Code(Operand Code) consists of A0~A12 and BA0~BA1 used for Mode Registering duing Extended MRS or MRS.
Before entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP
period from Prechagre command.
3. If a Read with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+tRP).
4. If a Write with Autoprecharge command is detected by memory component in CK(n), then there will be no command presented
to activated bank until CK(n+BL/2+1+tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery Time
(tWR) is needed to guarantee that the last data has been completely written.
5. If A10/AP is High when Row Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be
precharged.
Rev. 0.1 / June 2004
12
HYMD512G726B(L)4M-M/K/H/L
PACKAGE DIMENSIONS
Front
133.35
5.25
Register
30.48
1.2
PLL
Back
Side
3.99
.157max
(Front)
Register
1.27+/-0.10
0.05+/-0.004
Rev. 0.1 / June 2004
13
SERIAL PRESENCE DETECT
SPD SPECIFICATION
(128Mx72 Registered DDR DIMM)
Rev. 0.1 / June 2004
14
HYMD512G726B(L)4M-M/K/H/L
SERIAL PRESENCE DETECT
Byte
Function Description
0
Number of Bytes written into serial memory at module
manufacturer
1
Total number of Bytes in SPD device
2
Fundamental memory type
3
4
5
Function Supported
-M
-K
Hexa Value
-H
-L
-M
128 Bytes
-K
-H
-L
Note
80h
256 Bytes
08h
DDR SDRAM
07h
Number of row address on this assembly
13
0Dh
1
Number of column address on this assembly
12
0Ch
1
Number of physical banks on DIMM
1Bank
01h
6
Module data width
72 Bits
48h
7
Module data width (continued)
-
00h
8
Module voltage Interface levels(VDDQ)
9
DDR SDRAM cycle time at CAS Latency=2.5(tCK)
10
DDR SDRAM access time from clock at CL=2.5 (tAC) +/-0.75ns +/-0.75ns +/-0.75ns
11
Module configuration type
12
Refresh rate and type
13
SSTL 2.5V
7.5ns
7.5ns
04h
7.5ns
8ns
75h
75h
75h
80h
2
+/-0.8ns
75h
75h
75h
80h
2
ECC
02h
7.8us & Self refresh
82h
Primary DDR SDRAM width
x4
04h
14
Error checking DDR SDRAM data width
x4
04h
15
Minimum clock delay for back-to-back random column
address(tCCD)
1 CLK
01h
2,4,8
0Eh
16
Burst lengths supported
17
Number of banks on each DDR SDRAM
18
CAS latency supported
4 Banks
04h
2, 2.5
0Ch
19
CS latency
0
01h
20
WE latency
1
02h
21
DDR SDRAM module attributes
Registered, PLL
26h
+/-0.2Voltage tolerance,
Concurrent Auto Precharge
tRAS Lock Out
C0h
22
DDR SDRAM device attributes : General
23
DDR SDRAM cycle time at CL=2.0(tCK)
24
DDR SDRAM access time from clock at CL=2.0(tAC)
7.5ns
7.5ns
10ns
+/-0.75ns +/-0.75ns +/-0.75ns
10ns
75h
75h
A0h
A0h
2
+/-0.8ns
75h
75h
75h
80h
2
25
DDR SDRAM cycle time at CL=1.5(tCK)
-
00h
2
26
DDR SDRAM access time from clock at CL=1.5(tAC)
-
00h
2
27
Minimum row precharge time(tRP)
15ns
20ns
20ns
20ns
3Ch
50h
50h
50h
28
Minimum row activate to row active delay(tRRD)
15ns
15ns
15ns
15ns
3Ch
3Ch
3Ch
3Ch
29
Minimum RAS to CAS delay(tRCD)
15ns
20ns
20ns
20ns
3Ch
50h
50h
50h
30
Minimum active to precharge time(tRAS)
45ns
45ns
45ns
50ns
2Dh
2Dh
2Dh
32h
31
Module row density
32
Command and address signal input setup time(tIS)
0.9ns
0.9ns
0.9ns
1.1ns
90h
90h
90h
B0h
33
Command and address signal input hold time(tIH)
0.9ns
0.9ns
0.9ns
1.1ns
90h
90h
90h
B0h
34
Data signal input setup time(tDS)
0.5ns
0.5ns
0.5ns
0.6ns
50h
50h
50h
60h
35
Data signal input hold time(tDH)
0.5ns
0.5ns
0.5ns
0.6ns
50h
50h
50h
60h
1GB
36~40 Reserved for VCSDRAM
01h
Undefined
00h
41
Minimum active / auto-refresh time ( tRC)
60ns
65ns
65ns
70ns
3Ch
41h
41h
46h
42
Minimum auto-refresh to active/auto-refresh
command period(tRFC)
75ns
75ns
75ns
80ns
4Bh
4Bh
4Bh
50h
43
Maximum cycle time (tCK max)
12ns
12ns
12ns
12ns
30h
30h
30h
30h
44
Maximim DQS-DQ skew time(tDQSQ)
0.5ns
0.5ns
0.5ns
0.6ns
32h
32h
32h
3Ch
45
Maximum read data hold skew factor(tQHS)
0.75ns
0.75ns
0.75ns
0.75ns
75h
75h
75h
75h
B5h
4Fh
46~61 Superset information(may be used in future)
62
SPD Revision code
63
Checksum for Bytes 0~62
Rev. 0.1 / June 2004
Undefined
00h
Initial release
-
00h
5Dh
8Ah
15
HYMD512G726B(L)4M-M/K/H/L
SERIAL PRESENCE DETECT
Byte
64
65~71
72
Function Description
Function Supported
-M
Manufacturer JEDEC ID Code
-K
-L
-M
-K
-H
Hynix JEDEC ID
ADh
-
00h
Hynix(Korea Area)
HSA(United States Area)
HSE(Europe Area)
HSJ(Japan Area)
Singapore
Asia Area
0*h
1*h
2*h
3*h
4*h
5*h
--------- Manufacturer JEDEC ID Code
Manufacturing location
-H
Hexa Value
73
Manufacture part number(Hynix Memory Module)
H
48h
74
-------- Manufacture part number(Hynix Memory Module)
Y
59h
75
-------- Manufacture part number(Hynix Memory Module)
M
4Dh
76
Manufacture part number (DDR SDRAM)
D
44h
77
Manufacture part number(Memory density)
5
35h
78
Manufacture part number(Module Depth)
1
31h
79
------- Manufacture part number(Module Depth)
2
32h
80
Manufacture part number(Module type)
G
47h
81
Manufacture part number(Data width)
7
37h
82
-------Manufacture part number(Data width)
2
32h
83
Manufacture part number(Refresh, # of Bank.)
84
Manufacture part number(Component Generation)
6(8K refresh,4Bank)
36h
B
42h
85
Manufacture part number(Component configuration)
4
34h
86
Manufacture part number(Low profile)
M
4Dh
87
Manufacture part number(Hyphen)
88
Manufacture part number(Minimum cycle time)
89~90
M
K
Manufacture part number(T.B.D)
-L
Note
6
2Dh
H
L
4Dh
4Bh
48h
Blank
20h
-
4Ch
91
Manufacture revision code(for Component)
-
92
Manufacture revision code (for PCB)
-
-
93
Manufacturing date(Year)
-
-
94
Manufacturing date(Week)
-
-
3
95~98
Module serial number
-
-
4
99~127
Manufacturer specific data (may be used in future)
128~255 Open for customer use
3
Undefined
00h
5
Undefined
00h
5
Note :
1. The bank address is excluded
2. This value is based on the component specification
3. These bytes are programmed by code of date week & date year
4. These bytes apply to Hynix’s own Module Serial Number System
5. These bytes undefined and coded as ‘00h’
6. Refer to Hynix Web Site
Byte 85~87, Low Power Part
Byte #
Function Description
85
86
87
Manufacture part number(Low power part)
Manufacture part number(Component Configuration)
Manufacture part number(Low profile)
Rev. 0.1 / June 2004
Function Supported
-M
-K
-H
L
4
M
Hexa Value
-L
-M
-K
-H
-L
Note
4Ch
34h
4Dh
16