NUMBER : RD-SDRJL-001 DATE :2003/08/13 -CL(REV:3) Single 10/100 BASE-TX Filtered Connector Module MODEL NO. : RJL-001 Features Fully shielded magnetics protect data from internally generated digital noise Reduces the overall length of the signal path for improved common mode performance Implements full common mode termination scheme with used and unused twisted pairs Meets IEEE802.3 Baseline Wander Compensation specification Integrates high voltage capacitor to chassis ground Supports all major transceivers with matched turns ration and complete integration of specified termination DESIGN FOR 100BASE-TX TRANSMISSION OVER UTP-5 CABLE OPERATING TEMP RANGE:-40 TO +85 STORAGE TEMP RANGE:-55 TO +125 PRIMARY OCL INDUCTANCE:350uH min AT100KHz/0.1Vrms with 8mA DC BIAS. With the LED lamp. Typical Performance Characteristics Insertion Loss (dB MAX) Return Loss (dB Min @100Ω) MHz MHz 0.3~100 100~125 0.5~40 60 80 100 -0.8 -1.2 -18 -14.5 -12 -10 Differential to Common Mode Rejection (dB MIN) MHz 0.3~100 -35 Cross talk (dB MIN) CMRR (dB MIN) MHz 20 40 60 80 100 -47 -40 -37 -35 -33 MHz 0.3~100 -30 Schematic Design on MDI Interface Circuitry Taimag USA 55 Charles Drive Tewksbury Ma 01876 tel: 978.777.7725 fax: 978.777.4877 http://www.Taimagusa.com Isolation Voltage (Vrms min) 1500 NUMBER : RD-SDRJL-001 DATE :2003/08/13 -CL(REV:3) Mechanical Specifications mm RECOMMENDED P.C.B LAYOUT COMPONENT SIDE OF BOARD Taimag USA 55 Charles Drive Tewksbury Ma 01876 tel: 978.777.7725 fax: 978.777.4877 http://www.Taimagusa.com NUMBER : RD-SDRJL-001 DATE :2003/08/13 -CL(REV:3) Ordering Information RJ L 001 RJ45 Series NO. With LED Requirements 1. Design and Construction Product shall be of design, construction and physical dimensions specified on applicable product drawing. 2. Materials and Finish A. Contact: RJ Contact : Phosphor Bronze, Thickness=0.30mm Finish : (a) Contact Area : 30µ”min. Gold (b) Solder tail Area : 100µ”min. Tin/Lead(9:1) (c) Under plating : 50µ”min. Nickel over all RJ Joint Contact : Brass, Thickness=0.35mm Finish : 100µ”min. Tin/Lead(9:1) over 50µ”min. Nickel LED Joint Contact : Brass, Thickness=0.30mm Finish : 100µ”min. Tin/Lead(9:1) over 50µ”min. Nickel B. Plastic Part : (1) Set Housing : Thermoplastic, PBT, Black UL FILE NO. : E130155 Manufacturer : NAN YA PLASTICS CORP. Grade :1403G3 Flame Class : UL 94V-0 (2) Insert : Thermoplastic, PBT, Black UL FILE NO. : E130155 Manufacturer : MITSUI Petrochemical Industries Grade : CH230N Flame Class : UL 94V-0 Taimag USA 55 Charles Drive Tewksbury Ma 01876 tel: 978.777.7725 fax: 978.777.4877 http://www.Taimagusa.com NUMBER : RD-SDRJL-001 DATE :2003/08/13 -CL(REV:3) (3) Spacer : Thermoplastic, PBT, Black UL FILE NO. : E130155 Manufacturer : NAN YA PLASTICS CORP. Grade : 1403G3 Flame Class : UL 94V-0 C. Shield Material : Cartridge t=0.25mm 10µ”-20µ” Thick Nickel over 10µ”-20µ” min Thick Nickel D. LED Lamp (a) Lens Color : Transparent with color (b) Emitted Color : Green & Yellow (c) View Angle : 65 (d) Wave Length : Green 568nm ; Yellow 585nm 3. Ratings (1) Voltage rating : 125 VAC (2) Current rating : 1.5A Durability : 1000 cycles with no function damage for RJ-45 . Abnormalities shall be present after the test. Low Level Contact Resistance : ∆R=300mΩ maximum (final) The sample should be mounted in the tester and fully mated and unmated 500 times per hour at the rate of 25mm/min. EIA-364-09C. Taimag USA 55 Charles Drive Tewksbury Ma 01876 tel: 978.777.7725 fax: 978.777.4877 http://www.Taimagusa.com