INTEL X7800

Intel® Core™2 Duo Processors and
Intel® Core™2 Extreme Processors
for Platforms Based on Mobile Intel®
965 Express Chipset Family
Datasheet
January 2008
Document Number: 316745-005
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS
OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING
TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,
MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
Legal Lines and Disclaimers
UNLESS OTHERWISE AGREED IN WRITING BY INTEL, THE INTEL PRODUCTS ARE NOT DESIGNED NOR INTENDED FOR ANY APPLICATION IN WHICH THE
FAILURE OF THE INTEL PRODUCT COULD CREATE A SITUATION WHERE PERSONAL INJURY OR DEATH MAY OCCUR.
Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics
of any features or instructions marked “reserved” or “undefined.” Intel reserves these for future definition and shall have no responsibility whatsoever for
conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with
this information.
The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published
specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Enabling Execute Disable Bit functionality requires a PC with a processor with Execute Disable Bit capability and a supporting operating system. Check
with your PC manufacturer on whether your system delivers Execute Disable Bit functionality.
Enhanced Intel SpeedStep® Technology for specified units of this processor available Q2/06. See the Processor Spec Finder at http://
processorfinder.intel.com or contact your Intel representative for more information.
Intel® Virtualization Technology requires a computer system with an enabled Intel® processor, BIOS, virtual machine monitor (VMM) and, for some
uses, certain platform software enabled for it. Functionality, performance or other benefits will vary depending on hardware and software configurations
and may require a BIOS update. Software applications may not be compatible with all operating systems. Please check with your application vendor.
This device is protected by U.S. patent numbers 5,315,448 and 6,516,132, and other intellectual property rights. The use of Macrovision's copy
protection technology in the device must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless
otherwise authorized in writing by Macrovision. Reverse engineering or disassembly is prohibited.
64-bit computing on Intel architecture requires a computer system with a processor, chipset, BIOS, operating system, device drivers and applications
enabled for Intel® 64 architecture. Processors will not operate (including 32-bit operation) without an Intel® 64 architecture-enabled BIOS.
Performance will vary depending on your hardware and software configurations. Consult with your system vendor for more information.
Intel, Pentium, Intel Core, Intel Core 2, Intel SpeedStep and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2007 - 2008, Intel Corporation. All rights reserved.
2
Datasheet
Contents
1
Introduction .............................................................................................................. 7
1.1
Terminology ....................................................................................................... 8
1.2
References ......................................................................................................... 9
2
Low Power Features ................................................................................................ 11
2.1
Clock Control and Low Power States .................................................................... 11
2.1.1 Core Low Power State Descriptions ........................................................... 13
2.1.2 Package Low Power State Descriptions ...................................................... 15
2.2
Enhanced Intel SpeedStep® Technology .............................................................. 18
2.2.1 Dynamic FSB Frequency Switching ........................................................... 19
2.2.2 Intel® Dynamic Acceleration Technology ................................................... 19
2.3
Extended Low Power States ................................................................................ 19
2.4
FSB Low Power Enhancements ............................................................................ 20
2.5
VID-x .............................................................................................................. 21
2.6
Processor Power Status Indicator (PSI-2) Signal .................................................... 21
3
Electrical Specifications ........................................................................................... 23
3.1
Power and Ground Pins ...................................................................................... 23
3.2
FSB Clock (BCLK[1:0]) and Processor Clocking ...................................................... 23
3.3
Voltage Identification ......................................................................................... 23
3.4
Catastrophic Thermal Protection .......................................................................... 26
3.5
Reserved and Unused Pins.................................................................................. 26
3.6
FSB Frequency Select Signals (BSEL[2:0])............................................................ 27
3.7
FSB Signal Groups............................................................................................. 27
3.8
CMOS Signals ................................................................................................... 29
3.9
Maximum Ratings.............................................................................................. 29
3.10 Processor DC Specifications ................................................................................ 30
4
Package Mechanical Specifications and Pin Information .......................................... 41
4.1
Package Mechanical Specifications ....................................................................... 41
4.2
Processor Pinout and Pin List .............................................................................. 49
4.3
Alphabetical Signals Reference ............................................................................ 69
5
Thermal Specifications and Design Considerations .................................................. 77
5.1
Thermal Specifications ....................................................................................... 80
5.1.1 Thermal Diode ....................................................................................... 81
5.1.2 Thermal Diode Offset .............................................................................. 83
5.1.3 Intel® Thermal Monitor........................................................................... 84
5.1.4 Digital Thermal Sensor............................................................................ 86
5.1.5 Out of Specification Detection .................................................................. 87
5.1.6 PROCHOT# Signal Pin ............................................................................. 87
Datasheet
3
Figures
1
2
3
4
5
6
7
8
9
10
11
12
13
Core Low Power States..............................................................................................12
Package Low Power States.........................................................................................13
Active VCC and ICC Loadline Intel Core 2 Duo Processors - Standard Voltage,
Low Voltage and Ultra Low Voltage and Intel Core 2 Extreme Processors |
(PSI# Not Asserted) .................................................................................................36
Deeper Sleep VCC and ICC Loadline Intel Core 2 Duo Processors Standard Voltage and Intel Core 2 Extreme Processors (PSI# Asserted)...........................37
Deeper Sleep VCC and ICC Loadline Intel Core 2 Duo Processor Low Voltage and Ultra Low Voltage (PSI# Asserted) ......................................................38
4-MB and Fused 2-MB Micro-FCPGA Processor Package Drawing (Sheet 1 of 2) .................42
4-MB and Fused 2-MB Micro-FCPGA Processor Package Drawing (Sheet 2 of 2) .................43
2-MB Micro-FCPGA Processor Package Drawing (Sheet 1 of 2) ........................................44
2-MB Micro-FCPGA Processor Package Drawing (Sheet 2 of 2) ........................................45
4-MB and Fused 2-MB Micro-FCBGA Processor Package Drawing (Sheet 1 of 2).................46
4-MB and Fused 2-MB Micro-FCBGA Processor Package Drawing (Sheet 2 of 2).................47
2-MB Micro-FCBGA Processor Package Drawing (Sheet 1 of 2) ........................................48
2-MB Micro-FCBGA Processor Package Drawing (Sheet 2 of 2) ........................................49
Tables
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
4
Coordination of Core Low Power States at the Package Level ..........................................13
Voltage Identification Definition ..................................................................................23
BSEL[2:0] Encoding for BCLK Frequency......................................................................27
FSB Pin Groups ........................................................................................................28
Processor Absolute Maximum Ratings..........................................................................29
Voltage and Current Specifications for the Intel Core 2 Duo Processors Standard Voltage......................................................................................................30
Voltage and Current Specifications for the Intel Core 2 Duo Processors Low Voltage.............................................................................................................32
Voltage and Current Specifications for the Intel Core 2 Duo -Ultra Low
Voltage Processors ...................................................................................................33
Voltage and Current Specifications for the Intel Core 2 Extreme Processors ......................34
FSB Differential BCLK Specifications ............................................................................38
AGTL+ Signal Group DC Specifications ........................................................................39
CMOS Signal Group DC Specifications..........................................................................40
Open Drain Signal Group DC Specifications ..................................................................40
The Coordinates of the Processor Pins as Viewed from the Top of the Package
(Sheet 1 of 2) ..........................................................................................................50
The Coordinates of the Processor Pins as Viewed from the Top of the Package
(Sheet 2 of 2) ..........................................................................................................51
Pin Listing by Pin Name .............................................................................................53
Pin Listing by Pin Number ..........................................................................................60
Signal Description.....................................................................................................69
Power Specifications for the Intel Core 2 Duo Processor - Standard Voltage ......................77
Power Specifications for the Intel Core 2 Duo Processor - Low Voltage .............................78
Power Specifications for the Intel Core 2 Duo Processor - Ultra Low Voltage .....................79
Power Specifications for the Intel Core 2 Extreme Processor ...........................................80
Thermal Diode Interface ............................................................................................81
Thermal Diode Parameters Using Diode Model ..............................................................82
Thermal Diode Parameters Using Transistor Model ........................................................83
Thermal Diode ntrim and Diode Correction Toffset ........................................................84
Datasheet
Revision History
Document
Number
Revision
Number
316745
-001
Description
• Initial Release
Date
May 2007
• Updates
316745
-002
— Chapter 1 added Intel® Core™2 Duo processor - Ultra
Low Voltage information
— Chapter 3 added Table 8 with Intel Core 2 Duo processor Ultra Low Voltage U7600 and U7500 specifications
— Chapter 3 updated Figure 3 and 5 with Intel Core 2 Duo
processor - Ultra Low Voltage information
— Chapter 5 added Table 19 with Intel Core 2 Duo processor
-Ultra Low Voltage U7600 and U7500 specifications
June 2007
• Updates
316745
-003
— Chapter 1 added Intel® Core™2 Extreme processor
— Chapter 3 added Table 9 with Intel Core 2 Extreme
processor X7800 specifications
— Chapter 3 updated Figure 3 and 4 with Intel Core 2
Extreme processor information
— Chapter 5 added Table 20 with Intel Core 2 Extreme
processor X7800 specifications
— Corrected the pin diagram for 4-MB Micro-FCPGA and
2-MB Micro-FCPGA Processor Package Drawings
July 2007
• Updates
316745
-004
— Chapter 3 added Intel Core 2 Extreme processor X7900
and Low Voltage processor L7700 specifications
— Chapter 5 added Intel Core 2 Extreme processor X7900
and Low Voltage processor L7700 specifications
August 2007
• Updates
316745
Datasheet
-005
— Chapter 3 added Table 8 with Intel Core 2 Duo processor Ultra Low Voltage U7700 specifications
— Chapter 5 added Table 21 with Intel Core 2 Duo processor
-Ultra Low Voltage U7700 specifications
January 2007
5
6
Datasheet
Introduction
1
Introduction
The Intel® Core™2 Duo processor on 65-nm process technology is the next generation
high-performance, low-power processor based on the Intel® Core™ microarchitecture.
The Intel Core 2 Duo processor supports the Mobile Intel® 965 Express Chipset and
Intel® 82801HBM ICH8M Controller Hub Based Systems. This document contains
electrical, mechanical and thermal specifications for the following processors:
• Intel Core 2 Duo processor - Standard Voltage
• Intel Core 2 Duo processor - Low Voltage
• Intel Core 2 Duo processor - Ultra Low Voltage
• Intel Core 2 Extreme processor
Note:
In this document, the Intel Core 2 Duo and Intel Core 2 Extreme processors are
referred to as the processor and Mobile Intel® 965 Express Chipset family is referred to
as the (G)MCH.
The following list provides some of the key features on this processor:
• Dual core processor for mobile with enhanced performance
• Intel architecture with Intel® Wide Dynamic Execution
• L1 Cache to Cache (C2C) transfer
• On-die, primary 32-KB instruction cache and 32-KB write-back data cache in each
core
• On-die, up to 4-MB second level shared cache with advanced transfer cache
architecture
• Streaming SIMD Extensions 2 (SSE2), Streaming SIMD Extensions 3 (SSE3) and
Supplemental Streaming SIMD Extensions 3 (SSSE3)
• 800-MHz Source-Synchronous Front Side Bus (FSB) for Intel Core 2 Extreme
processors, Intel Core 2 Duo standard and low voltage processors. 533-MHz FSB
for Intel Core 2 Duo ultra low voltage processors
• Advanced power management features including Enhanced Intel SpeedStep®
Technology and Dynamic FSB frequency switching.
• Intel Enhanced Deeper Sleep state with P_LVL5 I/O support
• Digital Thermal Sensor (DTS)
• Intel® 64 Technology
• Enhanced Intel® Virtualization Technology
• Intel® Dynamic Acceleration Technology
• Enhanced Multi Threaded Thermal Management (EMTTM)
• PSI2 functionality
• Standard voltage processors are offered in Micro-FCPGA and Micro-FCBGA
packaging. Low voltage and Ultra low voltage processors are offered in MicroFCBGA packaging only. Intel Core 2 Extreme processors are offered in Micro-FCPGA
packaging only.
• Execute Disable Bit support for enhanced security
Datasheet
7
Introduction
1.1
Terminology
Term
8
Definition
#
A “#” symbol after a signal name refers to an active low signal, indicating a
signal is in the active state when driven to a low level. For example, when
RESET# is low, a reset has been requested. Conversely, when NMI is high,
a nonmaskable interrupt has occurred. In the case of signals where the
name does not imply an active state but describes part of a binary
sequence (such as address or data), the “#” symbol implies that the signal
is inverted. For example, D[3:0] = “HLHL” refers to a hex ‘A’, and D[3:0]#
= “LHLH” also refers to a hex “A” (H= High logic level, L= Low logic level).
XXXX means that the specification or value is yet to be determined.
Front Side Bus
(FSB)
Refers to the interface between the processor and system core logic (also
known as the chipset components).
AGTL+
Advanced Gunning Transceiver Logic. Used to refer to Assisted GTL+
signaling technology on some Intel processors.
Storage
Conditions
Refers to a non-operational state. The processor may be installed in a
platform, in a tray, or loose. Processors may be sealed in packaging or
exposed to free air. Under these conditions, processor landings should not
be connected to any supply voltages, have any I/Os biased or receive any
clocks. Upon exposure to “free air” (i.e., unsealed packaging or a device
removed from packaging material) the processor must be handled in
accordance with moisture sensitivity labeling (MSL) as indicated on the
packaging material.
Enhanced Intel
SpeedStep®
Technology
Technology that provides power management capabilities to laptops.
Processor Core
Processor core die with integrated L1 and L2 cache. All AC timing and
signal integrity specifications are at the pads of the processor core.
Intel® 64
Technology
64-bit memory extensions to the IA-32 architecture.
Intel®
Virtualization
Technology
Processor virtualization which when used in conjunction with Virtual
Machine Monitor software enables multiple, robust independent software
environments inside a single platform.
TDP
Thermal Design Power
VCC
The processor core power supply
VSS
The processor ground
Datasheet
Introduction
1.2
References
Material and concepts available in the following documents may be beneficial when
reading this document.
Document
Document Number1,2
Intel® Core™ 2 Duo Processors For Intel® Centrino® Duo Processor
Technology Specification Update
314079
Mobile Intel® 965 Express Chipset Family Datasheet
316273
Mobile Intel® 965 Express Chipset Family Specification Update
316274
Intel® I/O Controller Hub 8 (ICH8)/ I/O Controller Hub 8M (ICH8M)
Datasheet
See http://
www.intel.com/design/
chipsets/datashts/
313056.htm
Intel® I/O Controller Hub 8 (ICH8)/ I/O Controller Hub 8M (ICH8M)
Specification Update
See http://
www.intel.com/design/
chipsets/specupdt/
313057.htm
Intel® 64 and IA-32 Architectures Software Developer’s Manual
See http://
www.intel.com/design/
pentium4/manuals/
index_new.htm
Intel® 64 and IA-32 Architectures Software Developer's Manuals
Documentation Change
See http://
developer.intel.com/
design/processor/
specupdt/252046.htm
Volume 1: Basic Architecture
253665
Volume 2A: Instruction Set Reference, A-M
253666
Volume 2B: Instruction Set Reference, N-Z
253667
Volume 3A: System Programming Guide
253668
Volume 3B: System Programming Guide
253669
NOTES:
1.
Contact your local Intel representative for the latest revision of this document.
§
Datasheet
9
Introduction
10
Datasheet
Low Power Features
2
Low Power Features
2.1
Clock Control and Low Power States
The processor supports low power states both at the individual core level and the
package level for optimal power management.
A core may independently enter the C1/AutoHALT, C1/MWAIT, C2, C3, and C4 low
power states. When both cores coincide in a common core low power state, the central
power management logic ensures that the entire processor enters the respective
package low power state by initiating a P_LVLx (P_LVL2, P_LVL3, P_LVL4, or P_LVL5)
I/O read to the chipset.
The processor implements two software interfaces for requesting low power states:
MWAIT instruction extensions with sub-state hints or P_LVLx reads to the ACPI P_BLK
register block mapped in the processor’s I/O address space. The P_LVLx I/O reads are
converted to equivalent MWAIT C-state requests inside the processor and do not
directly result in I/O reads on the processor FSB. The P_LVLx I/O monitor address does
not need to be set up before using the P_LVLx I/O read interface. The sub-state hints
used for each P_LVLx read can be configured through the Model Specific Register
(MSR).
If a core encounters a chipset break event while STPCLK# is asserted, then it asserts
the PBE# output signal. Assertion of PBE# when STPCLK# is asserted indicates to
system logic that individual cores should return to the C0 state and the processor
should return to the Normal state.
Figure 1 shows the core low power states and Figure 2 shows the package low power
states. Table 1 maps the core low power states to the package low power states.
Datasheet
11
Low Power Features
Figure 1.
Core Low Power States
Stop
Grant
STPCLK#
asserted
STPCLK#
de-asserted
C1/
MWAIT
STPCLK#
de-asserted
STPCLK#
de-asserted
STPCLK#
asserted
Core state
break
STPCLK#
asserted
C1/Auto
Halt
HLT instruction
MWAIT(C1)
Halt break
C0
Core State
break
†‡
C4
P_LVL4 or
ø
P_LVL5 or
MWAIT(C4)
P_LVL2 or
MWAIT(C2)
Core state
break
Core P_LVL3 or
state MWAIT(C3)
break
†
C2
†
C3
halt break = A20M# transition, INIT#, INTR, NMI, PREQ#, RESET#, SMI#, or APIC interrupt
core state break = (halt break OR Monitor event) AND STPCLK# high (not asserted)
† — STPCLK# assertion and de-assertion have no effect if a core is in C2, C3, or C4.
‡ — Core C4 state supports the package level Intel Enhanced Deeper
.
Sleep state
Ø — P_LVL5 read is issued once the L2 cache is reduced to zero.
12
Datasheet
Low Power Features
Figure 2.
Package Low Power States
SLP# asserted
STPCLK# asserted
Stop
Grant
Normal
DPSLP# asserted
SLP# deasserted
Deeper
†
Sleep
Deep
Sleep
Sleep
STPCLK# deasserted
DPRSTP# asserted
DPSLP# deasserted
DPRSTP# deasserted
Snoop Snoop
serviced occurs
Stop
Grant
Snoop
† — Deeper Sleep includes the Deeper Sleep state and Intel Enhanced Deeper Sleep state.
Table 1.
Coordination of Core Low Power States at the Package Level
Package State
Core1 State
Core0 State
C0
C11
C2
C3
C4
C0
Normal
Normal
Normal
Normal
Normal
C11
Normal
Normal
Normal
Normal
Normal
C2
Normal
Normal
Stop-Grant
Stop Grant
Stop Grant
C3
Normal
Normal
Stop-Grant
Deep Sleep
Deep Sleep
Deep Sleep
Deeper Sleep
/ Intel®
Enhanced
Deeper Sleep
C4
Normal
Normal
Stop-Grant
NOTES:
1.
AutoHALT or MWAIT/C1.
2.1.1
Core Low Power State Descriptions
2.1.1.1
Core C0 State
This is the normal operating state for cores in the processor.
2.1.1.2
Core C1/AutoHALT Powerdown State
C1/AutoHALT is a low power state entered when a core executes the HALT instruction.
The processor transitions to the C0 state upon occurrence of SMI#, INIT#, LINT[1:0]
(NMI, INTR), or FSB interrupt messages. RESET# causes the processor to immediately
initialize itself.
Datasheet
13
Low Power Features
A System Management Interrupt (SMI) handler returns execution to either Normal
state or the AutoHALT Powerdown state. See the Intel® 64 and IA-32 Architectures
Software Developer’s Manual, Volume 3A/3B: System Programmer's Guide for more
information.
The system can generate a STPCLK# while the processor is in the AutoHALT
Powerdown state. When the system deasserts the STPCLK# interrupt, the processor
returns execution to the HALT state.
While in AutoHALT Powerdown state, the dual core processor processes bus snoops and
snoops from the other core. The processor enters a snoopable sub-state (not shown in
Figure 1) to process the snoop and then return to the AutoHALT Powerdown state.
2.1.1.3
Core C1/MWAIT Powerdown State
C1/MWAIT is a low power state entered when the processor core executes the
MWAIT(C1) instruction. Processor behavior in the MWAIT state is identical to the
AutoHALT state except that Monitor events can cause the processor core to return to
the C0 state. See the Intel® 64 and IA-32 Architectures Software Developer’s Manual,
Volume 2A: Instruction Set Reference, A-M and Volume 2B: Instruction Set Reference,
N-Z, for more information.
2.1.1.4
Core C2 State
Individual cores of the dual core processor can enter the C2 state by initiating a P_LVL2
I/O read to the P_BLK or an MWAIT(C2) instruction, but the processor does not issue a
Stop-Grant Acknowledge special bus cycle unless the STPCLK# pin is also asserted.
While in the C2 state, the dual core processor processes bus snoops and snoops from
the other core. The processor enters a snoopable sub-state (not shown in Figure 1) to
process the snoop and then return to the C2 state.
2.1.1.5
Core C3 State
Individual cores of the dual core processor can enter the C3 state by initiating a P_LVL3
I/O read to the P_BLK or an MWAIT(C3) instruction. Before entering C3, the processor
core flushes the contents of its L1 caches into the processor’s L2 cache. Except for the
caches, the processor core maintains all its architectural state in the C3 state. The
monitor remains armed if it is configured. All of the clocks in the processor core are
stopped in the C3 state.
Because the core’s caches are flushed the processor keeps the core in the C3 state
when the processor detects a snoop on the FSB or when the other core of the dual core
processor accesses cacheable memory. The processor core transitions to the C0 state
upon occurrence of a Monitor event, SMI#, INIT#, LINT[1:0] (NMI, INTR), or FSB
interrupt message. RESET# causes the processor to immediately initialize itself.
2.1.1.6
Core C4 State
Individual cores of the dual core processor can enter the C4 state by initiating a P_LVL4
I/O read to the P_BLK or an MWAIT(C4) instruction. The processor core behavior in the
C4 state is nearly identical to the behavior in the C3 state. The only difference is that if
both processor cores are in C4, then the central power management logic requests that
the entire processor enter the Deeper Sleep package low power state (see
Section 2.1.2.6).
To enable the package level Intel Enhanced Deeper Sleep state, Dynamic Cache Sizing
and Intel Enhanced Deeper Sleep state fields must be configured in the software
programmable MSR. Refer to Section 2.1.2.6 for further details on Intel Enhanced
Deeper Sleep state.
14
Datasheet
Low Power Features
2.1.2
Package Low Power State Descriptions
2.1.2.1
Normal State
This is the normal operating state for the processor. The processor remains in the
Normal state when at least one of its cores is in the C0, C1/AutoHALT, or C1/MWAIT
state.
2.1.2.2
Stop-Grant State
When the STPCLK# pin is asserted by the chipset, each core of the dual core processor
enters the Stop-Grant state within 20-bus clocks after the response phase of the
processor-issued Stop-Grant Acknowledge special bus cycle. Processor cores that are
already in the C2, C3, or C4 state remain in their current low power state. When the
STPCLK# pin is deasserted, each core returns to its previous core low power state.
Since the AGTL+ signal pins receive power from the FSB, these pins should not be
driven (allowing the level to return to VCCP) for minimum power drawn by the
termination resistors in this state. In addition, all other input pins on the FSB should be
driven to the inactive state.
RESET# causes the processor to immediately initialize itself, but the processor stays in
Stop-Grant state. When RESET# is asserted by the system, the STPCLK#, SLP#,
DPSLP#, and DPRSTP# pins must be deasserted prior to RESET# deassertion. When
re-entering the Stop-Grant state from the Sleep state, STPCLK# should be deasserted
after the deassertion of SLP#.
While in Stop-Grant state, the processor services snoops and latch interrupts delivered
on the FSB. The processor latches SMI#, INIT# and LINT[1:0] interrupts and services
only one of each upon return to the Normal state.
The PBE# signal may be driven when the processor is in Stop-Grant state. PBE#
asserts if there is any pending interrupt or Monitor event latched within the processor.
Pending interrupts that are blocked by the EFLAGS.IF bit being clear causes assertion
of PBE#. Assertion of PBE# indicates to system logic that the entire processor should
return to the Normal state.
A transition to the Stop-Grant Snoop state occurs when the processor detects a snoop
on the FSB (see Section 2.1.2.3). A transition to the Sleep state (see Section 2.1.2.4)
occurs with the assertion of the SLP# signal.
2.1.2.3
Stop-Grant Snoop State
The processor responds to snoop or interrupt transactions on the FSB while in StopGrant state by entering the Stop-Grant Snoop state. The processor stays in this state
until the snoop on the FSB has been serviced (whether by the processor or another
agent on the FSB) or the interrupt has been latched. The processor returns to the StopGrant state once the snoop has been serviced or the interrupt has been latched.
2.1.2.4
Sleep State
The Sleep state is a low power state in which the processor maintains its context,
maintains the phase-locked loop (PLL), and stops all internal clocks. The Sleep state is
entered through assertion of the SLP# signal while in the Stop-Grant state. The SLP#
pin should only be asserted when the processor is in the Stop-Grant state. SLP#
assertions while the processor is not in the Stop-Grant state is out of specification and
may result in unapproved operation.
Datasheet
15
Low Power Features
In the Sleep state, the processor is incapable of responding to snoop transactions or
latching interrupt signals. No transitions or assertions of signals (with the exception of
SLP#, DPSLP# or RESET#) are allowed on the FSB while the processor is in Sleep
state. Snoop events that occur while in Sleep state or during a transition into or out of
Sleep state causes unpredictable behavior. Any transition on an input signal before the
processor has returned to the Stop-Grant state results in unpredictable behavior.
If RESET# is driven active while the processor is in the Sleep state, and held active,
then the processor resets itself, ignoring the transition through Stop-Grant state. If
RESET# is driven active while the processor is in the Sleep state, the SLP# and
STPCLK# signals should be deasserted immediately after RESET# is asserted to ensure
the processor correctly executes the Reset sequence.
While in the Sleep state, the processor is capable of entering an even lower power
state, the Deep Sleep state, by asserting the DPSLP# pin (See Section 2.1.2.5). While
the processor is in the Sleep state, the SLP# pin must be deasserted if another
asynchronous FSB event needs to occur.
2.1.2.5
Deep Sleep State
The Deep Sleep state is entered through assertion of the DPSLP# pin while in the Sleep
state. BCLK may be stopped during the Deep Sleep state for additional platform-level
power savings. BCLK stop/restart timings on appropriate chipset based platforms with
the CK505 clock chip are as follows:
• Deep Sleep entry: the system clock chip may stop/tristate BCLK within 2 BCLKs of
DPSLP# assertion. It is permissible to leave BCLK running during Deep Sleep.
• Deep Sleep exit: the system clock chip must drive BCLK to differential DC levels
within 2-3 ns of DPSLP# deassertion and start toggling BCLK within 10 BCLK
periods.
To re-enter the Sleep state, the DPSLP# pin must be deasserted. BCLK can be restarted after DPSLP# deassertion as described above. A period of 15 microseconds (to
allow for PLL stabilization) must occur before the processor can be considered to be in
the Sleep state. Once in the Sleep state, the SLP# pin must be deasserted to re-enter
the Stop-Grant state.
While in Deep Sleep state, the processor is incapable of responding to snoop
transactions or latching interrupt signals. No transitions of signals are allowed on the
FSB while the processor is in Deep Sleep state. When the processor is in Deep Sleep
state, it does not respond to interrupts or snoop transactions. Any transition on an
input signal before the processor has returned to Stop-Grant state results in
unpredictable behavior.
2.1.2.6
Deeper Sleep State
The Deeper Sleep state is similar to the Deep Sleep state but further reduces core
voltage levels. One of the potential lower core voltage levels is achieved by entering the
base Deeper Sleep state. The Deeper Sleep state is entered through assertion of the
DPRSTP# pin while in the Deep Sleep state. The other lower core voltage level, the
lowest possible in the processor, is achieved by entering the Intel Enhanced Deeper
Sleep state which is a sub-state of Deeper Sleep state. Intel Enhanced Deeper Sleep
state is entered through assertion of the DPRSTP# pin while in the Deep Sleep only
when the L2 cache has been completely shut down. Refer to Section 2.1.2.6.1 and
Section 2.1.2.6.2 for further details on reducing the L2 cache and entering Intel
Enhanced Deeper Sleep state.
In response to entering Deeper Sleep, the processor drives the VID code corresponding
to the Deeper Sleep core voltage on the VID[6:0] pins.
16
Datasheet
Low Power Features
Exit from Deeper Sleep or Intel Enhanced Deeper Sleep state is initiated by DPRSTP#
deassertion when either core requests a core state other than C4 or either core
requests a processor performance state other than the lowest operating point.
2.1.2.6.1
Intel Enhanced Deeper Sleep State
Intel Enhanced Deeper Sleep state is a sub-state of Deeper Sleep that extends powersaving capabilities by allowing the processor to further reduce core voltage once the L2
cache has been reduced to zero ways and completely shut down. The following events
occur when the processor enters Intel Enhanced Deeper Sleep state:
• The last core entering C4 causes the package to issue a P_LVL4 IO Read.
• Every concurrent package C4 entry reduces the L2 Cache a certain number of
cache ways, after which another P_LVL4 IO Read is issued to the chipset. By
default, half the cache is flushed per concurrent C4 entry.
• Once the cache is flushed, P_LVL4 IO Reads continue to be issued.
• The processor drives the VID code corresponding to the Intel Enhanced Deeper
Sleep state core voltage on the VID[6:0] pins.
At this point, snoops to the L2 are still serviced, which reduces the amount of time the
processor can reside at the Intel Enhanced Deeper Sleep state core voltage.
To improve the Intel Enhanced Deeper Sleep state residency, the (G)MCH features
P_LVL5 IO Read support. When enabled, the CPU issues a P_LVL5 IO read, once the L2
cache is flushed. The P_LVL5 IO read triggers a special chipset sequence to notify the
chipset to redirect all FSB traffic, except APIC messages, to memory instead of L2
cache. Therefore, the processor remains at the Intel Enhanced Deeper Sleep state core
voltage for a longer period of time.
2.1.2.6.2
Dynamic Cache Sizing
Dynamic Cache Sizing allows the processor to flush and disable a programmable
number of L2 cache ways upon each Deeper Sleep entry under the following
conditions:
• The second core is already in C4 and the Intel Enhanced Deeper Sleep state is
enabled (as specified in Section 2.1.1.6).
• The C0 timer, which tracks continuous residency in the Normal package state, has
not expired. This timer is cleared during the first entry into Deeper Sleep to allow
consecutive Deeper Sleep entries to shrink the L2 cache as needed.
• The FSB speed to processor core speed ratio is below the predefined L2 shrink
threshold.
If the FSB speed to processor core speed ratio is above the predefined L2 shrink
threshold, then L2 cache expansion is requested. If the ratio is zero, then the ratio is
not taken into account for Dynamic Cache Sizing decisions.
Upon STPCLK# deassertion, the first core exiting Intel Enhanced Deeper Sleep state
expands the L2 cache to two ways and invalidate previously disabled cache ways. If the
L2 cache reduction conditions stated above still exist when the last core returns to C4
and the package enters Intel Enhanced Deeper Sleep state, then the L2 is shrunk to
zero again. If a core requests a processor performance state resulting in a higher ratio
than the predefined L2 shrink threshold, the C0 timer expires, or the second core (not
the one currently entering the interrupt routine) requests the C1, C2, or C3 states,
then all of L2 expands upon the next interrupt event.
L2 cache shrink prevention may be enabled as needed on occasion through an
MWAIT(C4) sub-state field. If shrink prevention is enabled the processor does not enter
Intel Enhanced Deeper Sleep state because the L2 cache remains valid and in full size.
Datasheet
17
Low Power Features
2.2
Enhanced Intel SpeedStep® Technology
The processor features Enhanced Intel SpeedStep Technology. Following are the key
features of Enhanced Intel SpeedStep Technology:
• Multiple voltage and frequency operating points provide optimal performance at the
lowest power.
• Voltage and frequency selection is software-controlled by writing to processor
MSRs:
— If the target frequency is higher than the current frequency, Vcc is ramped up
in steps by placing new values on the VID pins, and the PLL then locks to the
new frequency.
— If the target frequency is lower than the current frequency, the PLL locks to the
new frequency, and the VCC is changed through the VID pin mechanism.
— Software transitions are accepted at any time. If a previous transition is in
progress the new transition is deferred until the previous transition completes.
• The processor controls voltage ramp rates internally to ensure glitch-free
transitions.
• Low transition latency and large number of transitions possible per second:
— Processor core (including L2 cache) is unavailable for up to 10 ms during the
frequency transition.
— The bus protocol (BNR# mechanism) is used to block snooping.
• Improved Intel® Thermal Monitor mode:
— When the on-die thermal sensor indicates that the die temperature is too high,
the processor can automatically perform a transition to a lower frequency and
voltage specified in a software-programmable MSR.
— The processor waits for a fixed time period. If the die temperature is down to
acceptable levels, an up-transition to the previous frequency and voltage point
occurs.
— An interrupt is generated for the up and down Intel Thermal Monitor transitions
enabling better system-level thermal management.
• Enhanced thermal management features:
— Digital Thermal Sensor and Out of Specification detection
— Intel Thermal Monitor 1 in addition to Intel Thermal Monitor 2 in case of
unsuccessful Intel Thermal Monitor 2 transition.
— Dual core thermal management synchronization.
Each core in the dual processor implements an independent MSR for controlling
Enhanced Intel SpeedStep Technology, but both cores must operate at the same
frequency and voltage. The processor has performance state coordination logic to
resolve frequency and voltage requests from the two cores into a single frequency and
voltage request for the package as a whole. If both cores request the same frequency
and voltage, then the processor transitions to the requested common frequency and
voltage. If the two cores have different frequency and voltage requests, then the
processor takes the highest of the two frequencies and voltages as the resolved
request, and transition to that frequency and voltage.
The processor also supports Dynamic FSB Frequency Switching and Intel® Dynamic
Acceleration Technology mode on select SKUS. The operating system can take
advantage of these features and request a lower operating point called SuperLFM (due
to Dynamic FSB Frequency Switching) and a higher operating point Intel Dynamic
Acceleration Technology mode.
18
Datasheet
Low Power Features
2.2.1
Dynamic FSB Frequency Switching
Dynamic FSB frequency switching effectively reduces the internal bus clock frequency
in half to further decrease the minimum processor operating frequency from the
Enhanced Intel SpeedStep Technology performance states and achieve the Super Low
Frequency Mode (SuperLFM). This feature is supported at FSB frequencies of 800-MHz
and does not entail a change in the external bus signal (BCLK) frequency. Instead, both
the processor and (G)MCH internally lower their BCLK reference frequency to 50% of
the externally visible frequency. Both the processor and (G)MCH maintain a virtual
BCLK signal (“VBCLK”) that is aligned to the external BCLK but at half the frequency.
After a downward shift, it would appear externally as if the bus is running with a
100-MHz base clock in all aspects, except that the actual external BCLK remains at
200 MHz. The transition into SuperLFM, a “down-shift”, is done following a handshake
between the processor and (G)MCH. A similar handshake is used to indicate an “upshift”, a change back to normal operating mode.
2.2.2
Intel® Dynamic Acceleration Technology
The processor supports Intel Dynamic Acceleration Technology mode on select
platforms. The Intel Dynamic Acceleration Technology mode feature allows one core of
the processor to temporarily operate at a higher frequency point when the other core is
inactive and the operating system requests increased performance. This higher
frequency is called the opportunistic frequency and the maximum rated operating
frequency is the guaranteed frequency.
Note:
Intel Core 2 Extreme processors do not support Intel Dynamic Acceleration mode.
Intel Dynamic Acceleration Technology mode enabling requires:
• Exposure, via BIOS, of the opportunistic frequency as the highest ACPI P state.
• Enhanced Multi-Threaded Thermal Management (EMTTM).
• Intel Dynamic Acceleration Technology mode and EMTTM MSR configuration via
BIOS.
When in Intel Dynamic Acceleration Technology mode, it is possible for both cores to be
active under certain internal conditions. In such a scenario the processor may draw a
Instantaneous current (ICC_CORE_INST) for a short duration of tINST; however, the
average ICC current is lesser than or equal to ICCDES current specification. Please refer
to the Processor DC Specifications section for more details.
2.3
Extended Low Power States
Extended low power states (CxE) optimize for power by forcibly reducing the
performance state of the processor when it enters a package low power state. Instead
of directly transitioning into the package low power state, the extended package low
power state first reduces the performance state of the processor by performing an
Enhanced Intel SpeedStep Technology transition down to the lowest operating point.
Upon receiving a break event from the package low power state, control returns to the
software while an Enhanced Intel SpeedStep Technology transition up to the initial
operating point occurs. The advantage of this feature is that it significantly reduces
leakage while in low power states.
Note:
Datasheet
Long-term reliability cannot be assured unless all the Extended Low Power states are
enabled.
19
Low Power Features
The processor implements two software interfaces for requesting extended package
low power states: MWAIT instruction extensions with sub-state hints and via BIOS by
configuring MSR bits to automatically promote package low power states to extended
package low power states.
Extended Stop-Grant and Extended Deeper Sleep must be enabled via the
BIOS for the processor to remain within specification. Any attempt to operate
the processor outside these operating limits may result in permanent damage to the
processor. As processor technology changes, enabling the extended low power states
becomes increasingly crucial when building computer systems. Maintaining the proper
BIOS configuration is key to reliable, long-term system operation. Not complying with
this guideline may affect the long-term reliability of the processor.
Enhanced Intel SpeedStep Technology transitions are multistep processes that require
clocked control. These transitions cannot occur when the processor is in the Sleep or
Deep Sleep package low power states since processor clocks are not active in these
states. Extended Deeper Sleep state configuration lowers core voltage to the Deeper
Sleep level while in Deeper Sleep and, upon exit, automatically transitions to the lowest
operating voltage and frequency to reduce snoop service latency. The transition to the
lowest operating point or back to the original software requested point may not be
instantaneous. Furthermore, upon very frequent transitions between active and idle
states, the transitions may lag behind the idle state entry resulting in the processor
either executing for a longer time at the lowest operating point or running idle at a high
operating point. Observations and analyses show this behavior should not significantly
impact total power savings or performance score while providing power benefits in
most other cases.
2.4
FSB Low Power Enhancements
The processor incorporates FSB low power enhancements:
• Dynamic FSB Power Down
• BPRI# control for address and control input buffers
• Dynamic Bus Parking
• Dynamic On Die Termination disabling
• Low VCCP (I/O termination voltage)
The processor incorporates the DPWR# signal that controls the data bus input buffers
on the processor. The DPWR# signal disables the buffers when not used and activates
them only when data bus activity occurs, resulting in significant power savings with no
performance impact. BPRI# control also allows the processor address and control input
buffers to be turned off when the BPRI# signal is inactive. Dynamic Bus Parking allows
a reciprocal power reduction in chipset address and control input buffers when the
processor deasserts its BR0# pin. The On Die Termination on the processor FSB buffers
is disabled when the signals are driven low, resulting in additional power savings. The
low I/O termination voltage is on a dedicated voltage plane, independent of the core
voltage, enabling low I/O switching power at all times.
2.5
VID-x
The processor implements the VID-x feature when in Intel Dynamic
Acceleration Technology mode. VID-x provides the ability for the processor to
request core voltage level reductions greater than one VID tick. The quantity of VID
ticks to be reduced depends on the specific performance state in which the processor is
running. This improved voltage regulator efficiency during periods of reduced power
20
Datasheet
Low Power Features
consumption allows for leakage current reduction, which results in platform power
savings and extended battery life. There is no platform-level change required to
support this feature as long as the VR vendor supports the VID-x feature.
2.6
Processor Power Status Indicator (PSI-2) Signal
The processor incorporates the PSI# signal that is asserted when the processor is in a
reduced power consumption state. PSI# can be used to improve intermediate and light
load efficiency of the voltage regulator, resulting in platform power savings and
extended battery life. The algorithm that the processor uses for determining when to
assert PSI# is different from the algorithm used in previous mobile processors. PSI-2
functionality improves overall voltage regulator efficiency over a wide power range
based on the C-state and P-state of the two cores. The combined C-state and P-state of
both cores are used to dynamically predict processor power. PSI-2 functionality is
expanded further to support three processor states:
• Both cores are in idle state
• Only one core is in active state
• Both cores are in active state
§
Datasheet
21
Low Power Features
22
Datasheet
Electrical Specifications
3
Electrical Specifications
3.1
Power and Ground Pins
For clean, on-chip power distribution, the processor has a large number of VCC (power)
and VSS (ground) inputs. All power pins must be connected to VCC power planes while
all VSS pins must be connected to system ground planes. Use of multiple power and
ground planes is recommended to reduce I*R drop. The processor VCC pins must be
supplied the voltage determined by the VID (Voltage ID) pins.
3.2
FSB Clock (BCLK[1:0]) and Processor Clocking
BCLK[1:0] directly controls the FSB interface speed as well as the core frequency of the
processor. As in previous generation processors, the processor core frequency is a
multiple of the BCLK[1:0] frequency. The processor uses a differential clocking
implementation.
3.3
Voltage Identification
The processor uses seven voltage identification pins,VID[6:0], to support automatic
selection of power supply voltages. The VID pins for processor are CMOS outputs
driven by the processor VID circuitry. Table 2 specifies the voltage level corresponding
to the state of VID[6:0]. A 1 refers to a high-voltage level and a 0 refers to low-voltage
level.
Table 2.
Datasheet
Voltage Identification Definition (Sheet 1 of 4)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
0
0
0
0
0
0
0
1.5000
0
0
0
0
0
0
1
1.4875
0
0
0
0
0
1
0
1.4750
0
0
0
0
0
1
1
1.4625
0
0
0
0
1
0
0
1.4500
0
0
0
0
1
0
1
1.4375
0
0
0
0
1
1
0
1.4250
0
0
0
0
1
1
1
1.4125
0
0
0
1
0
0
0
1.4000
0
0
0
1
0
0
1
1.3875
0
0
0
1
0
1
0
1.3750
0
0
0
1
0
1
1
1.3625
0
0
0
1
1
0
0
1.3500
0
0
0
1
1
0
1
1.3375
0
0
0
1
1
1
0
1.3250
0
0
0
1
1
1
1
1.3125
0
0
1
0
0
0
0
1.3000
0
0
1
0
0
0
1
1.2875
0
0
1
0
0
1
0
1.2750
0
0
1
0
0
1
1
1.2625
0
0
1
0
1
0
0
1.2500
0
0
1
0
1
0
1
1.2375
23
Electrical Specifications
Table 2.
24
Voltage Identification Definition (Sheet 2 of 4)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
0
0
1
0
1
1
0
1.2250
0
0
1
0
1
1
1
1.2125
0
0
1
1
0
0
0
1.2000
0
0
1
1
0
0
1
1.1875
0
0
1
1
0
1
0
1.1750
0
0
1
1
0
1
1
1.1625
0
0
1
1
1
0
0
1.1500
0
0
1
1
1
0
1
1.1375
0
0
1
1
1
1
0
1.1250
0
0
1
1
1
1
1
1.1125
0
1
0
0
0
0
0
1.1000
0
1
0
0
0
0
1
1.0875
0
1
0
0
0
1
0
1.0750
0
1
0
0
0
1
1
1.0625
0
1
0
0
1
0
0
1.0500
0
1
0
0
1
0
1
1.0375
0
1
0
0
1
1
0
1.0250
0
1
0
0
1
1
1
1.0125
0
1
0
1
0
0
0
1.0000
0
1
0
1
0
0
1
0.9875
0
1
0
1
0
1
0
0.9750
0
1
0
1
0
1
1
0.9625
0
1
0
1
1
0
0
0.9500
0
1
0
1
1
0
1
0.9375
0
1
0
1
1
1
0
0.9250
0
1
0
1
1
1
1
0.9125
0
1
1
0
0
0
0
0.9000
0
1
1
0
0
0
1
0.8875
0
1
1
0
0
1
0
0.8750
0
1
1
0
0
1
1
0.8625
0
1
1
0
1
0
0
0.8500
0
1
1
0
1
0
1
0.8375
0
1
1
0
1
1
0
0.8250
0
1
1
0
1
1
1
0.8125
0
1
1
1
0
0
0
0.8000
0
1
1
1
0
0
1
0.7875
0
1
1
1
0
1
0
0.7750
0
1
1
1
0
1
1
0.7625
0
1
1
1
1
0
0
0.7500
0
1
1
1
1
0
1
0.7375
0
1
1
1
1
1
0
0.7250
0
1
1
1
1
1
1
0.7125
1
0
0
0
0
0
0
0.7000
1
0
0
0
0
0
1
0.6875
1
0
0
0
0
1
0
0.6750
1
0
0
0
0
1
1
0.6625
1
0
0
0
1
0
0
0.6500
Datasheet
Electrical Specifications
Table 2.
Datasheet
Voltage Identification Definition (Sheet 3 of 4)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
1
0
0
0
1
0
1
0.6375
1
0
0
0
1
1
0
0.6250
1
0
0
0
1
1
1
0.6125
1
0
0
1
0
0
0
0.6000
1
0
0
1
0
0
1
0.5875
1
0
0
1
0
1
0
0.5750
1
0
0
1
0
1
1
0.5625
1
0
0
1
1
0
0
0.5500
1
0
0
1
1
0
1
0.5375
1
0
0
1
1
1
0
0.5250
1
0
0
1
1
1
1
0.5125
1
0
1
0
0
0
0
0.5000
1
0
1
0
0
0
1
0.4875
1
0
1
0
0
1
0
0.4750
1
0
1
0
0
1
1
0.4625
1
0
1
0
1
0
0
0.4500
1
0
1
0
1
0
1
0.4375
1
0
1
0
1
1
0
0.4250
1
0
1
0
1
1
1
0.4125
1
0
1
1
0
0
0
0.4000
1
0
1
1
0
0
1
0.3875
1
0
1
1
0
1
0
0.3750
1
0
1
1
0
1
1
0.3625
1
0
1
1
1
0
0
0.3500
1
0
1
1
1
0
1
0.3375
1
0
1
1
1
1
0
0.3250
1
0
1
1
1
1
1
0.3125
1
1
0
0
0
0
0
0.3000
1
1
0
0
0
0
1
0.2875
1
1
0
0
0
1
0
0.2750
1
1
0
0
0
1
1
0.2625
1
1
0
0
1
0
0
0.2500
1
1
0
0
1
0
1
0.2375
1
1
0
0
1
1
0
0.2250
1
1
0
0
1
1
1
0.2125
1
1
0
1
0
0
0
0.2000
1
1
0
1
0
0
1
0.1875
1
1
0
1
0
1
0
0.1750
1
1
0
1
0
1
1
0.1625
1
1
0
1
1
0
0
0.1500
1
1
0
1
1
0
1
0.1375
1
1
0
1
1
1
0
0.1250
1
1
0
1
1
1
1
0.1125
1
1
1
0
0
0
0
0.1000
1
1
1
0
0
0
1
0.0875
1
1
1
0
0
1
0
0.0750
1
1
1
0
0
1
1
0.0625
25
Electrical Specifications
Table 2.
3.4
Voltage Identification Definition (Sheet 4 of 4)
VID6
VID5
VID4
VID3
VID2
VID1
VID0
VCC (V)
1
1
1
0
1
0
0
0.0500
1
1
1
0
1
0
1
0.0375
1
1
1
0
1
1
0
0.0250
1
1
1
0
1
1
1
0.0125
1
1
1
1
0
0
0
0.0000
1
1
1
1
0
0
1
0.0000
1
1
1
1
0
1
0
0.0000
1
1
1
1
0
1
1
0.0000
1
1
1
1
1
0
0
0.0000
1
1
1
1
1
0
1
0.0000
1
1
1
1
1
1
0
0.0000
1
1
1
1
1
1
1
0.0000
Catastrophic Thermal Protection
The processor supports the THERMTRIP# signal for catastrophic thermal protection. An
external thermal sensor should also be used to protect the processor and the system
against excessive temperatures. Even with the activation of THERMTRIP#, which halts
all processor internal clocks and activity, leakage current can be high enough that the
processor cannot be protected in all conditions without power removal to the processor.
If the external thermal sensor detects a catastrophic processor temperature of 125°C
(maximum), or if the THERMTRIP# signal is asserted, the VCC supply to the processor
must be turned off within 500 ms to prevent permanent silicon damage due to thermal
runaway of the processor. THERMTRIP# functionality is not guaranteed if the
PWRGOOD signal is not asserted.
3.5
Reserved and Unused Pins
All RESERVED (RSVD) pins must remain unconnected. Connection of these pins to VCC,
VSS, or to any other signal (including each other) may result in component malfunction
or incompatibility with future processors. See Section 4.2 for a pin listing of the
processor and the location of all RSVD pins.
For reliable operation, always connect unused inputs or bidirectional signals to an
appropriate signal level. Unused active low AGTL+ inputs may be left as no connects if
AGTL+ termination is provided on the processor silicon. Unused active high inputs
should be connected through a resistor to ground (VSS). Unused outputs can be left
unconnected.
The TEST1 and TEST2 pins must have a stuffing option of separate pull-down resistors
to VSS.
For the purpose of testability, route the TEST3 and TEST5 signals through a groundreferenced Zo = 55-Ω trace that ends in a via that is near a GND via and is accessible
through an oscilloscope connection.
26
Datasheet
Electrical Specifications
3.6
FSB Frequency Select Signals (BSEL[2:0])
The BSEL[2:0] signals are used to select the frequency of the processor input clock
(BCLK[1:0]). These signals should be connected to the clock chip and the appropriate
chipset on the platform. The BSEL encoding for BCLK[1:0] is shown in Table 3.
Table 3.
3.7
BSEL[2:0] Encoding for BCLK Frequency
BSEL[2]
BSEL[1]
BSEL[0]
BCLK Frequency
L
L
L
RESERVED
L
L
H
133 MHz
L
H
H
RESERVED
L
H
L
200 MHz
H
H
L
RESERVED
H
H
H
RESERVED
H
L
H
RESERVED
H
L
L
RESERVED
FSB Signal Groups
The FSB signals have been combined into groups by buffer type in the following
sections. AGTL+ input signals have differential input buffers, which use GTLREF as a
reference level. In this document, the term “AGTL+ Input” refers to the AGTL+ input
group as well as the AGTL+ I/O group when receiving. Similarly, “AGTL+ Output” refers
to the AGTL+ output group as well as the AGTL+ I/O group when driving.
With the implementation of a source synchronous data bus, two sets of timing
parameters need to be specified. One set is for common clock signals, which are
dependent upon the rising edge of BCLK0 (ADS#, HIT#, HITM#, etc.) and the second
set is for the source synchronous signals, which are relative to their respective strobe
lines (data and address) as well as the rising edge of BCLK0. Asychronous signals are
still present (A20M#, IGNNE#, etc.) and can become active at any time during the
clock cycle. Table 4 identifies which signals are common clock, source synchronous,
and asynchronous.
Datasheet
27
Electrical Specifications
Table 4.
FSB Pin Groups
Signal Group
Signals1
Type
AGTL+ Common Clock Input
Synchronous
to BCLK[1:0]
BPRI#, DEFER#, PREQ#5, RESET#, RS[2:0]#, TRDY#
AGTL+ Common Clock I/O
Synchronous
to BCLK[1:0]
ADS#, BNR#, BPM[3:0]#3, BR0#, DBSY#, DRDY#, HIT#,
HITM#, LOCK#, PRDY#3, DPWR#
Signals
AGTL+ Source Synchronous
I/O
Synchronous
to assoc.
strobe
Associated Strobe
REQ[4:0]#,
A[16:3]#
ADSTB[0]#
A[35:17]#
ADSTB[1]#
D[15:0]#,
DINV0#
DSTBP0#,
DSTBN0#
D[31:16]#,
DINV1#
DSTBP1#,
DSTBN1#
D[47:32]#,
DINV2#
DSTBP2#,
DSTBN2#
D[63:48]#,
DINV3#
DSTBP3#,
DSTBN3#
AGTL+ Strobes
Synchronous
to BCLK[1:0]
ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#
CMOS Input
Asynchronous
A20M#, DPRSTP#, DPSLP#, IGNNE#, INIT#, LINT0/INTR,
LINT1/NMI, PWRGOOD, SMI#, SLP#, STPCLK#
Open Drain Output
Asynchronous
FERR#, IERR#, THERMTRIP#
Open Drain I/O
Asynchronous
PROCHOT#4
CMOS Output
Asynchronous
PSI#, VID[6:0], BSEL[2:0]
CMOS Input
Synchronous
to TCK
TCK, TDI, TMS, TRST#
Open Drain Output
Synchronous
to TCK
FSB Clock
Clock
Power/Other
TDO
BCLK[1:0]
COMP[3:0], DBR#2, GTLREF, RSVD, TEST2, TEST1, THERMDA,
THERMDC, VCC, VCCA, VCCP, VCC_SENSE, VSS, VSS_SENSE
NOTES:
1.
Refer to Chapter 4 for signal descriptions and termination requirements.
2.
In processor systems where there is no debug port implemented on the system board, these signals are
used to support a debug port interposer. In systems with the debug port implemented on the system
board, these signals are no connects.
3.
BPM[2:1]# and PRDY# are AGTL+ output only signals.
4.
PROCHOT# signal type is open drain output and CMOS input.
5.
On die termination differs from other AGTL+ signals.
28
Datasheet
Electrical Specifications
3.8
CMOS Signals
CMOS input signals are shown in Table 4. Legacy output FERR#, IERR# and other nonAGTL+ signals (THERMTRIP# and PROCHOT#) utilize Open Drain output buffers. These
signals do not have setup or hold time specifications in relation to BCLK[1:0]. However,
all of the CMOS signals are required to be asserted for more than four BCLKs in order
for the processor to recognize them. See Section 3.10 for the DC specifications for the
CMOS signal groups.
3.9
Maximum Ratings
Table 5 specifies absolute maximum and minimum ratings. If the processor stays within
functional operation limits, functionality and long-term reliability can be expected.
Caution:
At conditions outside functional operation condition limits, but within absolute
maximum and minimum ratings, neither functionality nor long term reliability can be
expected. At conditions exceeding absolute maximum and minimum ratings, neither
functionality nor long term reliability can be expected.
Caution:
Precautions should always be taken to avoid high static voltages or electric fields.
Table 5.
Processor Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Unit
Notes1
-40
85
°C
2, 3, 4
TSTORAGE
Processor storage
temperature
VCC
Any processor supply voltage
with respect to VSS
-0.3
1.55
V
VinAGTL+
AGTL+ buffer DC input
voltage with respect to VSS
-0.1
1.55
V
VinAsynch_CMOS
CMOS buffer DC input
voltage with respect to VSS
-0.1
1.55
V
NOTES:
1.
For functional operation, all processor electrical, signal quality, mechanical and thermal
specifications must be satisfied.
2.
Storage temperature is applicable to storage conditions only. In this scenario, the
processor must not receive a clock, and no lands can be connected to a voltage bias.
Storage within these limits does not affect the long term reliability of the device. For
functional operation, please refer to the processor case temperature specifications.
3.
This rating applies to the processor and does not include any tray or packaging.
4.
Failure to adhere to this specification can affect the long term reliability of the processor.
Datasheet
29
Electrical Specifications
3.10
Processor DC Specifications
The processor DC specifications in this section are defined at the processor
core (pads) unless noted otherwise. See Table 4 for the pin signal definitions and
signal pin assignments.
Table 6 through Table 8 list the DC specifications for the processor and are valid only
while meeting specifications for junction temperature, clock frequency, and input
voltages. The Highest Frequency Mode (HFM) and Super Low Frequency Mode
(SuperLFM) refer to the highest and lowest core operating frequencies supported on
the processor. Active mode load line specifications apply in all states except in the Deep
Sleep and Deeper Sleep states. VCC,BOOT is the default voltage driven by the voltage
regulator at power up in order to set the VID values. Unless specified otherwise, all
specifications for the processor are at Tjunction = 100°C. Care should be taken to read
all notes associated with each parameter.
c
Table 6.
Voltage and Current Specifications for the Intel Core 2 Duo Processors Standard Voltage (Sheet 1 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
1, 2
VCCDAM
VCC in Intel® Dynamic Acceleration
Technology Mode
1.0375
1.3500
V
VCCHFM
VCC at High Frequency Mode (HFM)
1.0375
1.3000
V
1, 2
VCCLFM
VCC at Low Frequency Mode (LFM)
0.8500
1.0500
V
1, 2, 8
VCCSLFM
VCC at Super Low Frequency Mode (SuperLFM)
0.7500
0.9500
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
V
2
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VCCDC4
VCC at Intel® Enhanced Deeper Sleep Voltage
ICCDES
Standard Voltage Processor ICC Recommended
Design Target
1.20
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.6000
0.8000
V
1, 2
0.5500
0.7500
V
1, 2, 8
44
A
6
Standard Voltage ICC for the Processor
Processor
Number
ICC
T7800
T7700
T7500
T7300
T7250
T7100
Core Frequency/Voltage
2.6
2.4
2.2
2.0
2.0
1.8
1.2
0.8
GHz
GHz
GHz
GHz
GHz
GHz
GHz
GHz
&
&
&
&
&
&
&
&
VCCHFM
VCCHFM
VCCHFM
VCCHFM
VCCHFM
VCCHFM
VCCLFM
VCCSLFM
41
41
41
41
41
41
30.1
25.5
3, 4, 5, 12, 13
3, 4, 5, 12, 13
A
3, 4, 5, 12, 13
3, 4, 5, 12, 14
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
27.9
17.0
A
3, 4, 12
ISLP
ICC Sleep
HFM
SuperLFM
27.4
16.8
A
3, 4, 12
30
Datasheet
Electrical Specifications
Table 6.
Voltage and Current Specifications for the Intel Core 2 Duo Processors Standard Voltage (Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IDSLP
ICC Deep Sleep
HFM
SuperLFM
25.0
16.0
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
11.5
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
9.4
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at
Processor Package Pin
600
A/µs
7, 9
ICCA
ICC for VCCA Supply
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
4.5
2.5
A
A
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
in such a way that two processors at the same frequency may have different settings within the VID range.
Note that this differs from the VID employed by the processor during a power management event (Intel
Thermal Monitor 2, Enhanced Intel SpeedStep Technology, or Extended Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-mΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 100°C Tj.
4.
Specified at the nominal VCC.
5.
800-MHz FSB supported
6.
Instantaneous current ICC_CORE_INST of 55 A has to be sustained for short time (tINST) of 10 µs. Average
current is less than maximum specified ICCDES. VR OCP threshold should be high enough to support current
levels described herein.
7.
Measured at the bulk capacitors on the motherboard.
8.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor is lesser than or
equal to 350 mV.
9.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
10.
This is a power-up peak current specification, which is applicable when VCCP is high and VCC_CORE is low.
11.
This is a steady-state ICC current specification, which is applicable when both VCCP and VCC_CORE are high.
12.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode is lesser than ICC in HFM.
13.
4-M L2 cache.
14.
2-M L2 cache.
Datasheet
31
Electrical Specifications
Table 7.
Voltage and Current Specifications for the Intel Core 2 Duo Processors - Low
Voltage
Symbol
Parameter
Min
Typ
Max
Unit
Notes
1.3000
V
1, 2
VCCDAM
VCC in Intel® Dynamic Acceleration Technology
Mode
VCCHFM
VCC at High Frequency Mode (HFM)
0.9000
1.2000
V
1, 2
VCCLFM
VCC at Low Frequency Mode (LFM)
0.9000
1.0500
V
1, 2, 13
VCCSLFM
VCC at Super Low Frequency Mode (SuperLFM)
0.7500
0.9500
V
1, 2
VCC,BOOT
Default VCC Voltage for Initial Power Up
V
2
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VCCDC4
VCC at Intel® Enhanced Deeper Sleep Voltage
ICCDES
Low Voltage Processor ICC Recommended Design
Target
0.9000
1.20
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.6000
0.8000
V
1, 2
0.5500
0.7000
V
1, 2, 13
23
A
6
23
23
23
21
14.2
A
3, 4, 5,
8, 12
Low Voltage ICC for the Processor
Processor
Number
ICC
L7700
L7500
L7300
Core Frequency/Voltage
1.8
1.6
1.4
1.2
0.8
GHz
GHz
GHz
GHz
GHz
&
&
&
&
&
VCCHFM
VCCHFM
VCCHFM
VCCLFM
VCCSLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
11.7
8.3
A
3, 4, 12
ISLP
ICC Sleep
HFM
SuperLFM
11.4
8.1
A
3, 4, 12
IDSLP
ICC Deep Sleep
HFM
SuperLFM
10.0
7.3
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
6.3
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
4.7
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
600
A/µs
7, 9
ICCA
ICC for VCCA Supply
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
4.5
2.5
A
A
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
32
Datasheet
Electrical Specifications
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-mΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
Specified at 100°C Tj.
Specified at the nominal VCC.
800-MHz FSB supported.
Instantaneous current ICC_CORE_INST of 30 A has to be sustained for short time (tINST) of 10 µs. Average
current is less than maximum specified ICCDES. VR OCP threshold should be high enough to support current
levels described herein.
Measured at the bulk capacitors on the motherboard.
4-M L2 cache.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
This is a power-up peak current specification, which is applicable when VCCP is high and VCC_CORE is low.
This is a steady-state ICC current specification, which is applicable when both VCCP and VCC_CORE are high.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode is lesser than Icc in HFM.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor is lesser than or
equal to 350 mV.
Table 8.
Voltage and Current Specifications for the Intel Core 2 Duo -Ultra Low Voltage
Processors (Sheet 1 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCDAM
VCC in Intel® Dynamic Acceleration Mode
0.8000
1.2000
V
1, 2
VCCHFM
VCC at High Frequency Mode (HFM)
0.8000
0.9750
V
1, 2
VCCLFM
VCC at Low Frequency Mode (LFM)
0.7500
0.9500
V
1, 2, 13
V
2
VCC,BOOT
Default VCC Voltage for Initial Power Up
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VCCDC4
VCC at Intel® Enhanced Deeper Sleep voltage
ICCDES
Ultra Low Voltage Processor ICC Recommended
Design Target
1.20
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.6000
0.8000
V
1, 2
0.5500
0.7500
V
1, 2, 13
17
A
6
16
16
16
13.8
A
3, 4, 5,
8, 12,
14
Ultra Low Voltage ICC for the Processor
Processor
Number
ICC
U7700
U7600
U7500
Core Frequency/Voltage
1.33
1.20
1.06
0.80
GHz
GHz
GHz
GHz
&
&
&
&
VCCHFM
VCCHFM
VCCHFM
VCCLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
LFM
7.4
6.5
A
3, 4, 12
ISLP
ICC Sleep
HFM
LFM
7.2
6.3
A
3, 4, 12
IDSLP
ICC Deep Sleep
HFM
LFM
6.2
5.7
A
3, 4, 12
IDPRSLP
ICC Deeper Sleep
4.9
A
3, 4
Datasheet
33
Electrical Specifications
Table 8.
Voltage and Current Specifications for the Intel Core 2 Duo -Ultra Low Voltage
Processors (Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
IDC4
ICC Intel Enhanced Deeper Sleep
4.0
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
600
A/µs
7, 9
ICCA
ICC for VCCA Supply
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
4.5
2.5
A
A
10
11
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-mΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 100°C Tj.
4.
Specified at the nominal VCC.
5.
533-MHz FSB supported.
6.
Instantaneous current ICC_CORE_INST of 21 A has to be sustained for short time (tINST) of 10 µs. Average
current is less than maximum specified ICCDES. VR OCP threshold should be high enough to support current
levels described herein.
7.
Measured at the bulk capacitors on the motherboard.
8.
2-M L2 cache.
9.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
10.
This is a power-up peak current specification, which is applicable when VCCP is high and VCC_CORE is low.
11.
This is a steady-state ICC current specification, which is applicable when both VCCP and VCC_CORE are high.
12.
Processor ICC requirements in Intel Dynamic Acceleration Technology mode is lesser than ICC in HFM.
13.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor is lesser than or
equal to 350 mV.
14.
Dynamic FSB Frequency Switching not supported.
Table 9.
Voltage and Current Specifications for the Intel Core 2 Extreme Processors
(Sheet 1 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
VCCHFM
VCC at High Frequency Mode (HFM)
1.1000
1.3750
V
1, 2
VCCLFM
VCC at Low Frequency Mode (LFM)
1.0000
1.1000
V
1, 2, 7
VCCSLFM
VCC at Super Low Frequency Mode (SuperLFM)
0.9000
1.1000
V
1, 2
V
2
VCC,BOOT
Default VCC Voltage for Initial Power Up
VCCP
AGTL+ Termination Voltage
VCCA
PLL Supply Voltage
VCCDPRSLP
VCC at Deeper Sleep
VCCDC4
VCC at Intel® Enhanced Deeper Sleep Voltage
ICCDES
Extreme Processor ICC Recommended Design
Target
34
1.20
1.00
1.05
1.10
V
1.425
1.5
1.575
V
0.7000
0.9000
V
1, 2
0.6500
0.8500
V
1, 2, 7
55
A
Datasheet
Electrical Specifications
Table 9.
Voltage and Current Specifications for the Intel Core 2 Extreme Processors
(Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes
55
55
37
29
A
3, 4, 5,
11, 12
Extreme Processor ICC for the Processor
Processor
Number
ICC
X7900
X7800
Core Frequency/Voltage
2.80
2.60
1.20
0.80
GHz
GHz
GHz
GHz
&
&
&
&
VCCHFM
VCCHFM
VCCLFM
VCCSLFM
IAH,
ISGNT
ICC Auto-Halt & Stop-Grant
HFM
SuperLFM
29.8
21.6
A
3, 4
ISLP
ICC Sleep
HFM
SuperLFM
29.1
21.4
A
3, 4
IDSLP
ICC Deep Sleep
HFM
SuperLFM
26.6
20.6
A
3, 4
IDPRSLP
ICC Deeper Sleep
14.7
A
3, 4
IDC4
ICC Intel Enhanced Deeper Sleep
13.5
A
3, 4
dICC/DT
VCC Power Supply Current Slew Rate at Processor
Package Pin
600
A/µs
6, 8
ICCA
ICC for VCCA Supply
130
mA
ICCP
ICC for VCCP Supply before VCC Stable
ICC for VCCP Supply after VCC Stable
4.5
2.5
A
A
9
10
NOTES:
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across VCC_SENSE and VSS_SENSE pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-mΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 100°C Tj.
4.
Specified at the nominal VCC.
5.
800-MHz FSB Supported
6.
Measured at the bulk capacitors on the motherboard.
7.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor is lesser than or
equal to 350 mV.
8.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal VCC. Not 100% tested.
9.
This is a power-up peak current specification, which is applicable when VCCP is high and VCC_CORE is low.
10.
This is a steady-state Icc current specification, which is applicable when both VCCP and VCC_CORE are high.
11.
4-M L2 cache.
12.
Intel Dynamic Acceleration Technology not supported.
Datasheet
35
Electrical Specifications
Figure 3.
Active VCC and ICC Loadline Intel Core 2 Duo Processors - Standard Voltage,
Low Voltage and Ultra Low Voltage and Intel Core 2 Extreme Processors
(PSI# Not Asserted)
VCC-CORE [V]
Slope = -2.1 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {HFM|LFM}
VCC-CORE, DC max {HFM|LFM}
10mV= RIPPLE
VCC-CORE nom {HFM|LFM}
VCC-CORE, DC min {HFM|LFM}
VCC-CORE min {HFM|LFM}
+/-VCC-CORE Tolerance
= VR St. Pt. Error 1/
0
ICC-CORE max
{HFM|LFM}
ICC-CORE
[A]
N o t e 1 / V C C - C O R E S e t P o i n t E r r o r T o l e r a n c e is p e r b e lo w :
Tolerance
VCC-CORE VID Voltage Range
--------------- -------------------------------------------------------+ /-1.5%
VCC-CORE > 0.7500V
+/-11.5m V
36
0.75000V < VCC-CORE < 0.5000V
Datasheet
Electrical Specifications
Figure 4.
Deeper Sleep VCC and ICC Loadline Intel Core 2 Duo Processors - Standard
Voltage and Intel Core 2 Extreme Processors (PSI# Asserted)
VCC-CORE[V]
Slope = -2.1 mV/A at package
VccSense, VssSense pins.
Differential Remote Sense required.
VCC-CORE max {Deeper Sleep}
VCC-CORE, DC max
{Deeper Sleep}
13mV= RIPPLE
for PSI# Asserted
VCC-CORE nom
{Deeper Sleep}
VCC-CORE, DC min
{Deeper Sleep}
VCC-CORE min {Deeper Sleep}
+/-VCC-CORE Tolerance
= VR St. Pt. Error1/
0
Note 1/ Deeper Sleep V
Tolerance - PSI# Ripple
-----------------------------+/-[(VID*1.5%) - 3 mV]
CC-CORE
ICC-CORE max
{Deeper Sleep}
Set Point Error Tolerance is per below:
ICC-CORE
[A]
V CC-CORE VID Voltage Range
-------------------------------------------------------V CC-CORE > 0.7500V
+/-(11.5 mV - 3 mV)
0.5000V
< V CC-CORE < 0.7500V
+/- (25 mV - 3 mV)
0.4125V
< V CC-CORE < 0.5000V
NOTE: Deeper Sleep mode tolerance depends on VID value.
Datasheet
37
Electrical Specifications
Figure 5.
Deeper Sleep VCC and ICC Loadline Intel Core 2 Duo Processor - Low Voltage
and Ultra Low Voltage (PSI# Asserted)
NOTE: Deeper Sleep mode tolerance depends on VID value.
Table 10.
FSB Differential BCLK Specifications
Symbol
Parameter
VCROSS
Crossing Voltage
ΔVCROSS
Range of Crossing Points
VSWING
Differential Output Swing
ILI
Cpad
Input Leakage Current
Pad Capacitance
Min
Typ
0.3
Max
Unit
Notes1
0.55
V
2, 7, 8
140
mV
2, 7, 5
300
-5
0.95
1.2
mV
6
+5
µA
3
1.45
pF
4
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Crossing Voltage is defined as absolute voltage where rising edge of BCLK0 is equal to the
falling edge of BCLK1.
3.
For Vin between 0 V and VIH.
4.
Cpad includes die capacitance only. No package parasitics are included.
5.
ΔVCROSS is defined as the total variation of all crossing voltages as defined in Note 2.
6.
Measurement taken from differential waveform.
7.
Measurement taken from single-ended waveform.
8.
Only applies to the differential rising edge (Clock rising and Clock# falling).
38
Datasheet
Electrical Specifications
Table 11.
AGTL+ Signal Group DC Specifications
Symbol
VCCP
GTLREF
RCOMP
RODT
Parameter
I/O Voltage
Min
Typ
Max
Unit
1.00
1.05
1.10
V
Reference Voltage
Compensation Resistor
2/3 VCCP
27.23
Termination Resistor
27.5
27.78
55
Notes1
V
6
Ω
10
Ω
11
VIH
Input High Voltage
GTLREF+0.10
VCCP
VCCP+0.10
V
3,6
VIL
Input Low Voltage
-0.10
0
GTLREF-0.10
V
2,4
VOH
Output High Voltage
VCCP-0.10
VCCP
VCCP
Termination Resistance
50
55
61
Ω
7
Buffer On Resistance
22
25
28
Ω
5
±100
µA
8
2.55
pF
9
RTT
RON
ILI
Cpad
Input Leakage Current
Pad Capacitance
1.6
2.1
6
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
VIL is defined as the maximum voltage level at a receiving agent that is interpreted as a
logical low value.
3.
VIH is defined as the minimum voltage level at a receiving agent that is interpreted as a
logical high value.
4.
VIH and VOH may experience excursions above VCCP. However, input signal drivers must
comply with the signal quality specifications.
5.
This is the pull-down driver resistance. Measured at 0.31*VCCP. RON (min) = 0.4*RTT, RON
(typ) = 0.455*RTT, RON (max) = 0.51*RTT. RTT typical value of 55 Ω is used for RON typ/
min/max calculations.
6.
GTLREF should be generated from VCCP with a 1%-tolerance resistor divider. The VCCP
referred to in these specifications is the instantaneous VCCP.
7.
RTT is the on-die termination resistance measured at VOL of the AGTL+ output driver.
Measured at 0.31*VCCP. RTT is connected to VCCP on die.
8.
Specified with on die RTT and RON turned off. Vin between 0 and VCCP.
9.
Cpad includes die capacitance only. No package parasitics are included.
10.
This is the external resistor on the comp pins.
11.
On die termination resistance measured at 0.33*VCCP.
Datasheet
39
Electrical Specifications
Table 12.
CMOS Signal Group DC Specifications
Symbol
VCCP
Parameter
I/O Voltage
Min
Typ
Max
Unit
1.00
1.05
1.10
V
Notes1
VIH
Input High Voltage
0.7*VCCP
VCCP
VCCP+0.1
V
2
VIL
Input Low Voltage
CMOS
-0.10
0.00
0.3*VCCP
V
2
VOH
Output High Voltage
0.9*VCCP
VCCP
VCCP+0.1
V
2
VOL
Output Low Voltage
-0.10
0
0.1*VCCP
V
2
IOH
Output High Current
1.5
4.1
mA
5
IOL
Output Low Current
1.5
4.1
mA
4
ILI
Input Leakage Current
Cpad1
Pad Capacitance
Cpad2
Pad Capacitance for
CMOS Input
±100
µA
6
1.6
2.1
2.55
pF
7
0.95
1.2
1.45
3
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
The VCCP referred to in these specifications refers to instantaneous VCCP.
3.
Cpad2 includes die capacitance for all other CMOS input signals. No package parasitics are
included.
4.
Measured at 0.1*VCCP.
5.
Measured at 0.9*VCCP.
6.
For Vin between 0 V and VCCP. Measured when the driver is tristated.
7.
Cpad1 includes die capacitance only for DPRSTP#, DPSLP#, PWRGOOD. No package
parasitics are included.
Table 13.
Open Drain Signal Group DC Specifications
Symbol
Parameter
Min
Typ
Max
Unit
Notes1
VCCP-5%
VCCP
VCCP+5%
V
3
VOH
Output High Voltage
VOL
Output Low Voltage
0
0.20
V
IOL
Output Low Current
16
50
mA
2
ILO
Output Leakage Current
±200
µA
4
2.45
pF
5
Cpad
Pad Capacitance
1.9
2.2
NOTES:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Measured at 0.2 V.
3.
VOH is determined by value of the external pull-up resistor to VCCP.
4.
For Vin between 0 V and VOH.
5.
Cpad includes die capacitance only. No package parasitics are included.
§
40
Datasheet
Package Mechanical Specifications and Pin Information
4
Package Mechanical
Specifications and Pin
Information
4.1
Package Mechanical Specifications
The processor is available in 4-MB and 2-MB, 478-pin Micro-FCPGA packages as well as
4-MB and 2-MB, 479-ball Micro-FCBGA packages. The package mechanical dimensions,
keep-out zones, processor mass specifications, and package loading specifications are
shown in Figure 6 through Figure 13.
The mechanical package pressure specifications are in a direction normal to the surface
of the processor. This requirement is to protect the processor die from fracture risk due
to uneven die pressure distribution under tilt, stack-up tolerances and other similar
conditions. These specifications assume that a mechanical attach is designed
specifically to load one type of processor.
Intel also specifies that 15-lbf load limit should not be exceeded on any of Intel’s BGA
packages so as to not impact solder joint reliability after reflow. This load limit ensures
that impact to the package solder joints due to transient bend, shock, or tensile loading
is minimized. The 15-lbf metric should be used in parallel with the 689-kPa (100 psi)
pressure limit as long as neither limits are exceeded.
Moreover, the processor package substrate should not be used as a mechanical
reference or load-bearing surface for the thermal or mechanical solution. Please refer
to the Santa Rosa Platform Mechanical Design Guide for more details.
Caution:
The Micro-FCBGA package incorporates land-side capacitors. The land-side capacitors
are electrically conductive so care should be taken to avoid contacting the capacitors
with other electrically conductive materials on the motherboard. Doing so may short
the capacitors and possibly damage the device or render it inactive.
Note:
For E-step based processors refer the 4-MB and Fused 2-MB package drawings. For Mstep based processors refer to the 2-MB package drawings.
Datasheet
41
Package Mechanical Specifications and Pin Information
Figure 6.
4-MB and Fused 2-MB Micro-FCPGA Processor Package Drawing (Sheet 1 of 2)
h
Bottom View
Top View
Front View
Side View
&'%(
! "#$%$
)
P
Detail A
42
+ ,-
1--1.0.2
1/
* * *
* 1
1
1
1
1
1
)1.
* 6
!
34! ,./0
ø0.356 M C A B
ø0.254 M C
5 Datasheet
Package Mechanical Specifications and Pin Information
Figure 7.
4-MB and Fused 2-MB Micro-FCPGA Processor Package Drawing (Sheet 2 of 2)
"# $ %&
' Side View
(( $ %&
' Top View
ø0.305±0.25
ø0.406 M C A B
ø0.254 M C
!
!
Datasheet
Bottom View
43
Package Mechanical Specifications and Pin Information
Figure 8.
2-MB Micro-FCPGA Processor Package Drawing (Sheet 1 of 2)
Bottom View
Top View
Front View
Side View
&'%(
! "#$%$
)
P
Detail A
44
+ ,
1--1.0.2
1/
*
*
,./0
*
1
1
1
1
1
1
)1.
* 6
!
34! ø0.356 M C A B
ø0.254 M C
5 Datasheet
Package Mechanical Specifications and Pin Information
Figure 9.
2-MB Micro-FCPGA Processor Package Drawing (Sheet 2 of 2)
"# $ %&
' Side View
(( $ %&
' Top View
ø0.305±0.25
ø0.406 M C A B
ø0.254 M C
!
!
!
!
Datasheet
Bottom View
45
Package Mechanical Specifications and Pin Information
Figure 10.
4-MB and Fused 2-MB Micro-FCBGA Processor Package Drawing (Sheet 1 of 2)
'
'
'
'
#'
#
Top View
Bottom View
!!"
M
Front View
Detail B
$ !% &
Side View
$( )% *+",- ,%
./%-01!!
1%
'
Detail A
$ !% '
46
0.203
'
'
'
& &&
& &&
&
3
3
'
& & &3& &3& ' ' 3
3 (
)
'
'
#
#'
2
ø0.203 L C A B
ø0.071 L
Datasheet
Package Mechanical Specifications and Pin Information
Figure 11.
4-MB and Fused 2-MB Micro-FCBGA Processor Package Drawing (Sheet 2 of 2)
"# $ %&
' Side View
(( $ %&
' Top View
!
!
Datasheet
Bottom View
47
Package Mechanical Specifications and Pin Information
Figure 12.
2-MB Micro-FCBGA Processor Package Drawing (Sheet 1 of 2)
'
'
'
'
#'
#
Top View
Bottom View
!!"
M
Front View
Detail B
$ !% &
Side View
$( )% *+",- ,%
./%-01!!
Detail A
$ !% '
48
'
'
'
1%
'
0.203
'
'
#
#'
&
&
2
&&
&&
3
'
& & &3& &3& ' ' 3
3 (
)
ø0.203 L C A B
ø0.071 L
Datasheet
Package Mechanical Specifications and Pin Information
Figure 13.
2-MB Micro-FCBGA Processor Package Drawing (Sheet 2 of 2)
"# $ %&
' Side View
(( $ %&
' Top View
!
!
4.2
Bottom View
Processor Pinout and Pin List
Table 14 shows the top view pinout of the Intel Core 2 Duo mobile processor. The pin
list, arranged in two different formats, is shown in the following pages.
Datasheet
49
Package Mechanical Specifications and Pin Information
Table 14.
1
The Coordinates of the Processor Pins as Viewed from the Top of the Package
(Sheet 1 of 2)
2
3
4
5
6
7
8
9
10
11
12
13
A
VSS
SMI#
VSS
FERR#
A20M#
VCC
VSS
VCC
VCC
VSS
VCC
VCC
A
B
RSVD
INIT#
LINT1
DPSLP#
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VSS
B
RSVD
IGNNE
#
VSS
LINT0
THERM
TRIP#
VSS
VCC
VCC
VSS
VCC
VCC
C
PWRGO
OD
C
RESET#
VSS
D
VSS
RSVD
RSVD
VSS
STPCLK
#
SLP#
VSS
VCC
VCC
VSS
VCC
VSS
D
E
DBSY#
BNR#
VSS
HITM#
DPRSTP
#
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VCC
E
F
BR0#
VSS
RS[0]#
RS[1]#
VSS
RSVD
VCC
VSS
VCC
VCC
VSS
VCC
VSS
F
G
VSS
TRDY#
RS[2]#
VSS
BPRI#
HIT#
G
H
ADS#
REQ[1]
#
VSS
LOCK#
DEFER#
VSS
H
J
A[9]#
VSS
REQ[3]
#
A[3]#
VSS
VCCP
J
K
VSS
REQ[2]
#
REQ[0]
#
VSS
A[6]#
VCCP
K
L
REQ[4]#
A[13]#
VSS
A[5]#
A[4]#
VSS
L
M
ADSTB[0
]#
VSS
A[7]#
RSVD
VSS
VCCP
M
N
VSS
A[8]#
A[10]#
VSS
RSVD
VCCP
N
P
A[15]#
A[12]#
VSS
A[14]#
A[11]#
VSS
P
R
A[16]#
VSS
A[19]#
A[24]#
VSS
VCCP
R
T
VSS
RSVD
A[26]#
VSS
A[25]#
VCCP
T
U
A[23]#
A[30]#
VSS
A[21]#
A[18]#
VSS
U
V
ADSTB[1
]#
VSS
RSVD
A[31]#
VSS
VCCP
V
W
VSS
A[27]#
A[32]#
VSS
A[28]#
A[20]#
W
Y
COMP[3]
A[17]#
VSS
A[29]#
A[22]#
VSS
AA
COMP[2]
VSS
A[35]#
A[33]#
VSS
TDI
AB
VSS
A[34]#
TDO
VSS
TMS
TRST#
VCC
VSS
VCC
VCC
VSS
AC
PREQ#
PRDY#
VSS
BPM[3]
#
TCK
VSS
VCC
VSS
VCC
VCC
VSS
AD
BPM[2]#
VSS
BPM[1]
#
BPM[0]
#
VSS
VID[0]
VCC
VSS
VCC
VCC
VSS
Y
VCC
VSS
VCC
VCC
VSS
VCC
VCC
AA
VCC
VSS
AB
VCC
VCC
AC
VCC
VSS
AD
AE
VSS
VID[6]
VID[4]
VSS
VID[2]
PSI#
VSS
SENSE
VSS
VCC
VCC
VSS
VCC
VCC
AE
AF
TEST5
VSS
VID[5]
VID[3]
VID[1]
VSS
VCC
SENSE
VSS
VCC
VCC
VSS
VCC
VSS
AF
1
2
3
4
5
6
7
8
9
10
11
12
13
50
Datasheet
Package Mechanical Specifications and Pin Information
Table 15.
The Coordinates of the Processor Pins as Viewed from the Top of the Package
(Sheet 2 of 2)
14
15
16
17
18
19
20
21
22
23
24
25
26
A
VSS
VCC
VSS
VCC
VCC
VSS
VCC
BCLK[1]
BCLK[0]
VSS
THRMDA
VSS
TEST6
A
B
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VSS
BSEL[0]
BSEL[1]
VSS
THRMDC
VCCA
B
C
VSS
VCC
VSS
VCC
VCC
VSS
DBR#
BSEL[2]
VSS
TEST1
TEST3
VSS
VCCA
C
IERR#
PROCHO
T#
RSVD
VSS
DPWR#
TEST2
VSS
D
D
VCC
VCC
VSS
VCC
VCC
VSS
E
VSS
VCC
VSS
VCC
VCC
VSS
VCC
VSS
D[0]#
D[7]#
VSS
D[6]#
D[2]#
E
F
VCC
VCC
VSS
VCC
VCC
VSS
VCC
DRDY#
VSS
D[4]#
D[1]#
VSS
D[13]#
F
VCCP
D[3]#
VSS
D[9]#
D[5]#
VSS
G
H
G
H
VSS
D[12]#
D[15]#
VSS
DINV[0]#
DSTBP[
0]#
J
VCCP
VSS
D[11]#
D[10]#
VSS
DSTBN[
0]#
J
K
VCCP
D[14]#
VSS
D[8]#
D[17]#
VSS
K
D[29]#
DSTBN[
1]#
L
VSS
DSTBP[
1]#
M
L
VSS
D[22]#
M
VCCP
VSS
N
VCCP
P
VSS
R
VCCP
D[20]#
VSS
D[23]#
D[21]#
D[16]#
VSS
DINV[1]#
D[31]#
VSS
N
D[26]#
D[25]#
VSS
D[24]#
D[18]#
P
COMP[0
]
R
VSS
D[19]#
D[28]#
VSS
T
VCCP
D[37]#
VSS
D[27]#
D[30]#
VSS
T
U
VSS
DINV[2]#
D[39]#
VSS
D[38]#
COMP[1
]
U
V
VCCP
VSS
D[36]#
D[34]#
VSS
D[35]#
V
W
VCCP
D[41]#
VSS
D[43]#
D[44]#
VSS
W
D[40]#
DSTBN[
2]#
Y
A
A
Y
VSS
D[32]#
D[42]#
VSS
AA
VSS
VCC
VSS
VCC
VCC
VSS
VCC
D[50]#
VSS
D[45]#
D[46]#
VSS
DSTBP[
2]#
AB
VCC
VCC
VSS
VCC
VCC
VSS
VCC
D[52]#
D[51]#
VSS
D[33]#
D[47]#
VSS
A
B
AC
VSS
VCC
VSS
VCC
VCC
VSS
DINV[3
]#
VSS
D[60]#
D[63]#
VSS
D[57]#
D[53]#
AC
A
D
VCC
VCC
VSS
VCC
VCC
VSS
D[54]#
D[59]#
VSS
D[61]#
D[49]#
VSS
GTLREF
A
D
AE
VSS
VCC
VSS
VCC
VCC
VSS
VCC
D[58]#
D[55]#
VSS
D[48]#
DSTBN[3]
#
VSS
AE
VSS
TEST4
AF
25
26
AF
VCC
VCC
VSS
VCC
VCC
VSS
VCC
VSS
D[62]#
D[56]#
DSTBP[3]
#
14
15
16
17
18
19
20
21
22
23
24
Datasheet
51
Package Mechanical Specifications and Pin Information
This page is intentionally left blank.
52
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Table 16.
Pin Listing by Pin Name
(Sheet 1 of 16)
Pin Listing by Pin Name
(Sheet 2 of 16)
Pin
Number
Signal Buffer
Type
Direction
A[24]#
R4
Source Synch
Input/
Output
Pin Name
Pin
Number
Signal Buffer
Type
Direction
A[3]#
J4
Source Synch
Input/
Output
A[25]#
T5
Source Synch
A[4]#
L5
Source Synch
Input/
Output
Input/
Output
A[26]#
T3
Source Synch
A[5]#
L4
Source Synch
Input/
Output
Input/
Output
A[27]#
W2
Source Synch
A[6]#
K5
Source Synch
Input/
Output
Input/
Output
A[28]#
W5
Source Synch
A[7]#
M3
Source Synch
Input/
Output
Input/
Output
A[29]#
Y4
Source Synch
A[8]#
N2
Source Synch
Input/
Output
Input/
Output
A[30]#
U2
Source Synch
A[9]#
J1
Source Synch
Input/
Output
Input/
Output
A[31]#
V4
Source Synch
A[10]#
N3
Source Synch
Input/
Output
Input/
Output
A[32]#
W3
Source Synch
A[11]#
P5
Source Synch
Input/
Output
Input/
Output
A[33]#
AA4
Source Synch
A[12]#
P2
Source Synch
Input/
Output
Input/
Output
A[34]#
AB2
Source Synch
A[13]#
L2
Source Synch
Input/
Output
Input/
Output
A[35]#
AA3
Source Synch
A[14]#
P4
Source Synch
Input/
Output
Input/
Output
A20M#
A6
CMOS
Input
A[15]#
P1
Source Synch
Input/
Output
ADS#
H1
Common Clock
Input/
Output
A[16]#
R1
Source Synch
Input/
Output
ADSTB[0]#
M1
Source Synch
Input/
Output
A[17]#
Y2
Source Synch
Input/
Output
ADSTB[1]#
V1
Source Synch
Input/
Output
A[18]#
U5
Source Synch
Input/
Output
BCLK[0]
A22
Bus Clock
Input
BCLK[1]
A21
Bus Clock
Input
BNR#
E2
Common Clock
Input/
Output
Pin Name
A[19]#
R3
Source Synch
Input/
Output
A[20]#
W6
Source Synch
Input/
Output
BPM[0]#
AD4
Common Clock
Input/
Output
A[21]#
U4
Source Synch
Input/
Output
BPM[1]#
AD3
Common Clock
Output
AD1
Common Clock
Output
Y5
Source Synch
Input/
Output
BPM[2]#
A[22]#
BPM[3]#
AC4
Common Clock
A[23]#
U1
Source Synch
Input/
Output
Input/
Output
BPRI#
G5
Common Clock
Input
Datasheet
53
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 3 of 16)
Pin
Number
Signal Buffer
Type
Direction
BR0#
F1
Common Clock
Input/
Output
BSEL[0]
B22
CMOS
Output
BSEL[1]
B23
CMOS
Output
BSEL[2]
C21
CMOS
COMP[0]
R26
COMP[1]
Table 16.
Pin Listing by Pin Name
(Sheet 4 of 16)
Pin
Number
Signal Buffer
Type
Direction
D[15]#
H23
Source Synch
Input/
Output
D[16]#
N22
Source Synch
Input/
Output
Output
D[17]#
K25
Source Synch
Input/
Output
Power/Other
Input/
Output
D[18]#
P26
Source Synch
Input/
Output
U26
Power/Other
Input/
Output
D[19]#
R23
Source Synch
Input/
Output
COMP[2]
AA1
Power/Other
Input/
Output
D[20]#
L23
Source Synch
Input/
Output
COMP[3]
Y1
Power/Other
Input/
Output
D[21]#
M24
Source Synch
Input/
Output
D[0]#
E22
Source Synch
Input/
Output
D[22]#
L22
Source Synch
Input/
Output
D[1]#
F24
Source Synch
Input/
Output
D[23]#
M23
Source Synch
Input/
Output
D[2]#
E26
Source Synch
Input/
Output
D[24]#
P25
Source Synch
Input/
Output
D[3]#
G22
Source Synch
Input/
Output
D[25]#
P23
Source Synch
Input/
Output
D[4]#
F23
Source Synch
Input/
Output
D[26]#
P22
Source Synch
Input/
Output
D[5]#
G25
Source Synch
Input/
Output
D[27]#
T24
Source Synch
Input/
Output
D[6]#
E25
Source Synch
Input/
Output
D[28]#
R24
Source Synch
Input/
Output
D[7]#
E23
Source Synch
Input/
Output
D[29]#
L25
Source Synch
Input/
Output
D[8]#
K24
Source Synch
Input/
Output
D[30]#
T25
Source Synch
Input/
Output
D[9]#
G24
Source Synch
Input/
Output
D[31]#
N25
Source Synch
Input/
Output
D[10]#
J24
Source Synch
Input/
Output
D[32]#
Y22
Source Synch
Input/
Output
D[11]#
J23
Source Synch
Input/
Output
D[33]#
AB24
Source Synch
Input/
Output
D[12]#
H22
Source Synch
Input/
Output
D[34]#
V24
Source Synch
Input/
Output
D[13]#
F26
Source Synch
Input/
Output
D[35]#
V26
Source Synch
Input/
Output
D[14]#
K22
Source Synch
Input/
Output
D[36]#
V23
Source Synch
Input/
Output
Pin Name
54
Pin Name
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 5 of 16)
Pin
Number
Signal Buffer
Type
Direction
D[37]#
T22
Source Synch
Input/
Output
D[38]#
U25
Source Synch
D[39]#
U23
D[40]#
Table 16.
Pin Listing by Pin Name
(Sheet 6 of 16)
Pin
Number
Signal Buffer
Type
Direction
D[59]#
AD21
Source Synch
Input/
Output
Input/
Output
D[60]#
AC22
Source Synch
Input/
Output
Source Synch
Input/
Output
D[61]#
AD23
Source Synch
Input/
Output
Y25
Source Synch
Input/
Output
D[62]#
AF22
Source Synch
Input/
Output
D[41]#
W22
Source Synch
Input/
Output
D[63]#
AC23
Source Synch
Input/
Output
D[42]#
Y23
Source Synch
Input/
Output
DBR#
C20
CMOS
Output
Pin Name
Pin Name
DBSY#
E1
Common Clock
Input/
Output
DEFER#
H5
Common Clock
Input
DINV[0]#
H25
Source Synch
Input/
Output
Input/
Output
DINV[1]#
N24
Source Synch
Input/
Output
Source Synch
Input/
Output
DINV[2]#
U22
Source Synch
Input/
Output
AB25
Source Synch
Input/
Output
DINV[3]#
AC20
Source Synch
Input/
Output
D[48]#
AE24
Source Synch
Input/
Output
DPRSTP#
E5
CMOS
Input
B5
CMOS
Input
AD24
Source Synch
Input/
Output
DPSLP#
D[49]#
DPWR#
D24
Common Clock
Input/
Output
DRDY#
F21
Common Clock
Input/
Output
DSTBN[0]#
J26
Source Synch
Input/
Output
DSTBN[1]#
L26
Source Synch
Input/
Output
DSTBN[2]#
Y26
Source Synch
Input/
Output
DSTBN[3]#
AE25
Source Synch
Input/
Output
DSTBP[0]#
H26
Source Synch
Input/
Output
DSTBP[1]#
M26
Source Synch
Input/
Output
DSTBP[2]#
AA26
Source Synch
Input/
Output
D[43]#
W24
Source Synch
Input/
Output
D[44]#
W25
Source Synch
Input/
Output
D[45]#
AA23
Source Synch
D[46]#
AA24
D[47]#
D[50]#
D[51]#
D[52]#
D[53]#
D[54]#
D[55]#
D[56]#
D[57]#
D[58]#
Datasheet
AA21
AB22
AB21
AC26
AD20
AE22
AF23
AC25
AE21
Source Synch
Source Synch
Input/
Output
Input/
Output
Source Synch
Input/
Output
Source Synch
Input/
Output
Source Synch
Source Synch
Input/
Output
Input/
Output
Source Synch
Input/
Output
Source Synch
Input/
Output
Source Synch
Input/
Output
55
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 7 of 16)
Table 16.
Pin Listing by Pin Name
(Sheet 8 of 16)
Pin
Number
Signal Buffer
Type
Direction
DSTBP[3]#
AF24
Source Synch
Input/
Output
FERR#
A5
Open Drain
Output
GTLREF
AD26
Power/Other
Input
HIT#
G6
Common Clock
Input/
Output
HITM#
E4
Common Clock
Input/
Output
IERR#
D20
Open Drain
Output
STPCLK#
D5
CMOS
Input
IGNNE#
C4
CMOS
Input
TCK
AC5
CMOS
Input
INIT#
B3
CMOS
Input
TDI
AA6
CMOS
Input
LINT0
C6
CMOS
Input
TDO
AB3
Open Drain
Output
LINT1
B4
CMOS
Input
TEST1
C23
Test
TEST2
D25
Test
TEST3
C24
Test
TEST4
AF26
Test
Pin Name
Pin
Number
Signal Buffer
Type
RSVD
F6
Reserved
RSVD
M4
Reserved
RSVD
N5
Reserved
RSVD
T2
Reserved
RSVD
V3
Reserved
SLP#
D7
CMOS
Input
SMI#
A3
CMOS
Input
Pin Name
LOCK#
H4
Common Clock
Input/
Output
PRDY#
AC2
Common Clock
Output
PREQ#
AC1
Common Clock
Input
TEST5
AF1
Test
PROCHOT#
D21
Open Drain
Input/
Output
TEST6
A26
Test
PSI#
AE6
CMOS
Output
THERMTRIP
#
C7
Open Drain
PWRGOOD
D6
CMOS
Input
THRMDA
A24
Power/Other
THRMDC
B25
Power/Other
TMS
AB5
CMOS
REQ[0]#
K3
Source Synch
Input/
Output
REQ[1]#
H2
Source Synch
Input/
Output
Source Synch
Input/
Output
REQ[2]#
K2
Output
Input
TRDY#
G2
Common Clock
Input
TRST#
AB6
CMOS
Input
VCC
A7
Power/Other
VCC
A9
Power/Other
VCC
A10
Power/Other
VCC
A12
Power/Other
REQ[3]#
J3
Source Synch
Input/
Output
REQ[4]#
L1
Source Synch
Input/
Output
RESET#
C1
Common Clock
Input
VCC
A13
Power/Other
RS[0]#
F3
Common Clock
Input
VCC
A15
Power/Other
RS[1]#
F4
Common Clock
Input
VCC
A17
Power/Other
RS[2]#
G3
Common Clock
Input
VCC
A18
Power/Other
RSVD
B2
Reserved
VCC
A20
Power/Other
RSVD
C3
Reserved
VCC
AA7
Power/Other
RSVD
D2
Reserved
VCC
AA9
Power/Other
RSVD
D3
Reserved
VCC
AA10
Power/Other
RSVD
D22
Reserved
VCC
AA12
Power/Other
56
Direction
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 9 of 16)
Pin
Number
Signal Buffer
Type
VCC
AA13
Power/Other
VCC
AA15
VCC
Table 16.
Pin Listing by Pin Name
(Sheet 10 of 16)
Pin
Number
Signal Buffer
Type
VCC
AE18
Power/Other
Power/Other
VCC
AE20
Power/Other
AA17
Power/Other
VCC
AF9
Power/Other
VCC
AA18
Power/Other
VCC
AF10
Power/Other
VCC
AA20
Power/Other
VCC
AF12
Power/Other
VCC
AB7
Power/Other
VCC
AF14
Power/Other
VCC
AB9
Power/Other
VCC
AF15
Power/Other
VCC
AB10
Power/Other
VCC
AF17
Power/Other
VCC
AB12
Power/Other
VCC
AF18
Power/Other
VCC
AB14
Power/Other
VCC
AF20
Power/Other
VCC
AB15
Power/Other
VCC
B7
Power/Other
VCC
AB17
Power/Other
VCC
B9
Power/Other
VCC
AB18
Power/Other
VCC
B10
Power/Other
VCC
AB20
Power/Other
VCC
B12
Power/Other
VCC
AC7
Power/Other
VCC
B14
Power/Other
VCC
AC9
Power/Other
VCC
B15
Power/Other
VCC
AC10
Power/Other
VCC
B17
Power/Other
VCC
AC12
Power/Other
VCC
B18
Power/Other
VCC
AC13
Power/Other
VCC
B20
Power/Other
VCC
AC15
Power/Other
VCC
C9
Power/Other
VCC
AC17
Power/Other
VCC
C10
Power/Other
VCC
AC18
Power/Other
VCC
C12
Power/Other
VCC
AD7
Power/Other
VCC
C13
Power/Other
Pin Name
Direction
Pin Name
VCC
AD9
Power/Other
VCC
C15
Power/Other
VCC
AD10
Power/Other
VCC
C17
Power/Other
VCC
AD12
Power/Other
VCC
C18
Power/Other
VCC
AD14
Power/Other
VCC
D9
Power/Other
VCC
AD15
Power/Other
VCC
D10
Power/Other
VCC
AD17
Power/Other
VCC
D12
Power/Other
VCC
AD18
Power/Other
VCC
D14
Power/Other
VCC
AE9
Power/Other
VCC
D15
Power/Other
VCC
AE10
Power/Other
VCC
D17
Power/Other
VCC
AE12
Power/Other
VCC
D18
Power/Other
VCC
AE13
Power/Other
VCC
E7
Power/Other
VCC
AE15
Power/Other
VCC
E9
Power/Other
VCC
AE17
Power/Other
VCC
E10
Power/Other
Datasheet
Direction
57
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 11 of 16)
Pin
Number
Signal Buffer
Type
VCC
E12
Power/Other
VCC
E13
VCC
Table 16.
Pin Listing by Pin Name
(Sheet 12 of 16)
Pin
Number
Signal Buffer
Type
Direction
VID[2]
AE5
CMOS
Output
Power/Other
VID[3]
AF4
CMOS
Output
E15
Power/Other
VID[4]
AE3
CMOS
Output
VCC
E17
Power/Other
VID[5]
AF3
CMOS
Output
VCC
E18
Power/Other
VID[6]
AE2
CMOS
Output
VCC
E20
Power/Other
VSS
A2
Power/Other
VCC
F7
Power/Other
VSS
A4
Power/Other
VCC
F9
Power/Other
VSS
A8
Power/Other
VCC
F10
Power/Other
VSS
A11
Power/Other
VCC
F12
Power/Other
VSS
A14
Power/Other
VCC
F14
Power/Other
VSS
A16
Power/Other
VCC
F15
Power/Other
VSS
A19
Power/Other
VCC
F17
Power/Other
VSS
A23
Power/Other
VCC
F18
Power/Other
VSS
A25
Power/Other
VCC
F20
Power/Other
VSS
AA2
Power/Other
VCCA
B26
Power/Other
VSS
AA5
Power/Other
VCCA
C26
Power/Other
VSS
AA8
Power/other
VCCP
G21
Power/Other
VSS
AA11
Power/Other
VCCP
J6
Power/Other
VSS
AA14
Power/Other
VCCP
J21
Power/Other
VSS
AA16
Power/Other
VCCP
K6
Power/Other
VSS
AA19
Power/Other
VCCP
K21
Power/Other
VSS
AA22
Power/Other
VCCP
M6
Power/Other
VSS
AA25
Power/Other
VCCP
M21
Power/Other
VSS
AB1
Power/Other
VCCP
N6
Power/Other
VSS
AB4
Power/Other
VCCP
N21
Power/Other
VSS
AB8
Power/Other
VCCP
R6
Power/Other
VSS
AB11
Power/Other
VCCP
R21
Power/Other
VSS
AB13
Power/Other
VCCP
T6
Power/Other
VSS
AB16
Power/Other
VCCP
T21
Power/Other
VSS
AB19
Power/Other
VCCP
V6
Power/Other
VSS
AB23
Power/Other
VCCP
V21
Power/Other
VSS
AB26
Power/Other
VCCP
W21
Power/Other
VSS
AC3
Power/Other
VCCSENSE
AF7
Power/Other
VSS
AC6
Power/Other
VID[0]
AD6
CMOS
Output
VSS
AC8
Power/Other
VID[1]
AF5
CMOS
Output
VSS
AC11
Power/Other
Pin Name
58
Direction
Pin Name
Datasheet
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 13 of 16)
Pin
Number
Signal Buffer
Type
VSS
AC14
Power/Other
VSS
AC16
VSS
Table 16.
Pin Listing by Pin Name
(Sheet 14 of 16)
Pin
Number
Signal Buffer
Type
VSS
B16
Power/Other
Power/Other
VSS
B19
Power/Other
AC19
Power/Other
VSS
B21
Power/Other
VSS
AC21
Power/Other
VSS
B24
Power/Other
VSS
AC24
Power/Other
VSS
C2
Power/Other
VSS
AD2
Power/Other
VSS
C5
Power/Other
VSS
AD5
Power/Other
VSS
C8
Power/Other
Pin Name
Direction
Pin Name
VSS
AD8
Power/Other
VSS
C11
Power/Other
VSS
AD11
Power/Other
VSS
C14
Power/Other
VSS
AD13
Power/Other
VSS
C16
Power/Other
VSS
AD16
Power/Other
VSS
C19
Power/Other
VSS
AD19
Power/Other
VSS
C22
Power/Other
VSS
AD22
Power/Other
VSS
C25
Power/Other
VSS
AD25
Power/Other
VSS
D1
Power/Other
VSS
AE1
Power/Other
VSS
D4
Power/Other
VSS
AE4
Power/Other
VSS
D8
Power/Other
VSS
AE8
Power/Other
VSS
D11
Power/Other
VSS
AE11
Power/Other
VSS
D13
Power/Other
VSS
AE14
Power/Other
VSS
D16
Power/Other
VSS
AE16
Power/Other
VSS
D19
Power/Other
VSS
AE19
Power/Other
VSS
D23
Power/Other
VSS
AE23
Power/Other
VSS
D26
Power/Other
VSS
AE26
Power/Other
VSS
E3
Power/Other
VSS
AF2
Power/Other
VSS
E6
Power/Other
VSS
AF6
Power/Other
VSS
E8
Power/Other
VSS
AF8
Power/Other
VSS
E11
Power/Other
VSS
AF11
Power/Other
VSS
E14
Power/Other
VSS
AF13
Power/Other
VSS
E16
Power/Other
VSS
AF16
Power/Other
VSS
E19
Power/Other
VSS
AF19
Power/Other
VSS
E21
Power/Other
VSS
AF21
Power/Other
VSS
E24
Power/Other
VSS
AF25
Power/Other
VSS
F2
Power/Other
VSS
B6
Power/Other
VSS
F5
Power/Other
VSS
B8
Power/Other
VSS
F8
Power/Other
VSS
B11
Power/Other
VSS
F11
Power/Other
VSS
B13
Power/Other
VSS
F13
Power/Other
Datasheet
Direction
59
Package Mechanical Specifications and Pin Information
Table 16.
Pin Listing by Pin Name
(Sheet 15 of 16)
Pin
Number
Signal Buffer
Type
VSS
F16
Power/Other
VSS
F19
VSS
F22
Pin Name
Table 16.
Pin Listing by Pin Name
(Sheet 16 of 16)
Pin
Number
Signal Buffer
Type
VSS
R2
Power/Other
Power/Other
VSS
R5
Power/Other
Power/Other
VSS
R22
Power/Other
Direction
Pin Name
VSS
F25
Power/Other
VSS
R25
Power/Other
VSS
G1
Power/Other
VSS
T1
Power/Other
VSS
G4
Power/Other
VSS
T4
Power/Other
VSS
G23
Power/Other
VSS
T23
Power/Other
VSS
G26
Power/Other
VSS
T26
Power/Other
VSS
H3
Power/Other
VSS
U3
Power/Other
VSS
H6
Power/Other
VSS
U6
Power/Other
VSS
H21
Power/Other
VSS
U21
Power/Other
VSS
H24
Power/Other
VSS
U24
Power/Other
VSS
J2
Power/Other
VSS
V2
Power/Other
VSS
J5
Power/Other
VSS
V5
Power/Other
VSS
J22
Power/Other
VSS
V22
Power/Other
VSS
J25
Power/Other
VSS
V25
Power/Other
VSS
K1
Power/Other
VSS
W1
Power/Other
VSS
K4
Power/Other
VSS
W4
Power/Other
VSS
K23
Power/Other
VSS
W23
Power/Other
VSS
K26
Power/Other
VSS
W26
Power/Other
VSS
L3
Power/Other
VSS
Y3
Power/Other
VSS
L6
Power/Other
VSS
Y6
Power/Other
VSS
L21
Power/Other
VSS
Y21
Power/Other
VSS
L24
Power/Other
VSS
Y24
Power/Other
VSS
M2
Power/Other
VSSSENSE
AE7
Power/Other
VSS
M5
Power/Other
VSS
M22
Power/Other
VSS
M25
Power/Other
VSS
N1
Power/Other
VSS
N4
Power/Other
VSS
N23
Power/Other
VSS
N26
Power/Other
VSS
P3
Power/Other
VSS
P6
Power/Other
VSS
P21
Power/Other
VSS
P24
Power/Other
60
Table 17.
Direction
Output
Pin Listing by Pin Number
(Sheet 1 of 17)
Pin
Number
Signal
Buffer Type
VSS
A2
Power/Other
SMI#
A3
CMOS
VSS
A4
Power/Other
FERR#
A5
Open Drain
Output
A20M#
A6
CMOS
Input
VCC
A7
Power/Other
Pin Name
Direction
Input
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 2 of 17)
Pin
Number
Signal
Buffer Type
VSS
A8
Power/Other
VCC
A9
VCC
A10
Pin Name
Table 17.
Pin Listing by Pin Number
(Sheet 3 of 17)
Pin
Number
Signal
Buffer Type
VSS
AA16
Power/Other
Power/Other
VCC
AA17
Power/Other
Power/Other
VCC
AA18
Power/Other
Direction
Pin Name
Direction
VSS
A11
Power/Other
VSS
AA19
Power/Other
VCC
A12
Power/Other
VCC
AA20
Power/Other
VCC
A13
Power/Other
D[50]#
AA21
Source Synch
VSS
A14
Power/Other
VCC
A15
Power/Other
VSS
AA22
Power/Other
VSS
A16
Power/Other
D[45]#
AA23
Source Synch
Input/
Output
VCC
A17
Power/Other
VCC
A18
Power/Other
D[46]#
AA24
Source Synch
Input/
Output
VSS
AA25
Power/Other
DSTBP[2]#
AA26
Source Synch
VSS
AB1
Power/Other
A[34]#
AB2
Source Synch
Input/
Output
TDO
AB3
Open Drain
Output
VSS
AB4
Power/Other
TMS
AB5
CMOS
Input
TRST#
AB6
CMOS
Input
VCC
AB7
Power/Other
VSS
AB8
Power/Other
VCC
AB9
Power/Other
VCC
AB10
Power/Other
VSS
AB11
Power/Other
VCC
AB12
Power/Other
VSS
AB13
Power/Other
VCC
AB14
Power/Other
VSS
A19
Power/Other
VCC
A20
Power/Other
BCLK[1]
A21
Bus Clock
Input
BCLK[0]
A22
Bus Clock
Input
VSS
A23
Power/Other
THRMDA
A24
Power/Other
VSS
A25
Power/Other
TEST6
A26
Test
COMP[2]
AA1
Power/Other
VSS
AA2
Power/Other
Input/
Output
A[35]#
AA3
Source Synch
Input/
Output
A[33]#
AA4
Source Synch
Input/
Output
VSS
AA5
Power/Other
TDI
AA6
CMOS
VCC
AA7
Power/Other
VSS
AA8
Power/other
VCC
AA9
Power/Other
VCC
AA10
Power/Other
VSS
AA11
Power/Other
VCC
AA12
Power/Other
VCC
AA13
Power/Other
VSS
AA14
Power/Other
VCC
AA15
Power/Other
Datasheet
Input
VCC
AB15
Power/Other
VSS
AB16
Power/Other
VCC
AB17
Power/Other
VCC
AB18
Power/Other
VSS
AB19
Power/Other
VCC
AB20
Power/Other
D[52]#
AB21
Source Synch
Input/
Output
Input/
Output
Input/
Output
61
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 4 of 17)
Pin
Number
Signal
Buffer Type
Direction
D[51]#
AB22
Source Synch
Input/
Output
VSS
AB23
Power/Other
Pin Name
D[33]#
AB24
Source Synch
Input/
Output
D[47]#
AB25
Source Synch
Input/
Output
VSS
AB26
Power/Other
PREQ#
AC1
Common
Clock
Input
PRDY#
AC2
Common
Clock
Output
VSS
AC3
Power/Other
BPM[3]#
AC4
Common
Clock
Input/
Output
TCK
AC5
CMOS
Input
VSS
AC6
Power/Other
VCC
AC7
Power/Other
VSS
AC8
Power/Other
VCC
AC9
Power/Other
VCC
AC10
Power/Other
VSS
AC11
Power/Other
VCC
AC12
Power/Other
VCC
AC13
Power/Other
VSS
AC14
Power/Other
VCC
AC15
Power/Other
VSS
AC16
Power/Other
VCC
AC17
Power/Other
VCC
AC18
Power/Other
VSS
AC19
Power/Other
DINV[3]#
AC20
Source Synch
Input/
Output
VSS
AC21
Power/Other
D[60]#
AC22
Source Synch
Input/
Output
D[63]#
AC23
Source Synch
Input/
Output
VSS
D[57]#
62
AC24
AC25
Power/Other
Source Synch
Input/
Output
Table 17.
Pin Listing by Pin Number
(Sheet 5 of 17)
Pin
Number
Signal
Buffer Type
Direction
D[53]#
AC26
Source Synch
Input/
Output
BPM[2]#
AD1
Common
Clock
Output
VSS
AD2
Power/Other
BPM[1]#
AD3
Common
Clock
Output
BPM[0]#
AD4
Common
Clock
Input/
Output
VSS
AD5
Power/Other
VID[0]
AD6
CMOS
VCC
AD7
Power/Other
VSS
AD8
Power/Other
VCC
AD9
Power/Other
VCC
AD10
Power/Other
Pin Name
Output
VSS
AD11
Power/Other
VCC
AD12
Power/Other
VSS
AD13
Power/Other
VCC
AD14
Power/Other
VCC
AD15
Power/Other
VSS
AD16
Power/Other
VCC
AD17
Power/Other
VCC
AD18
Power/Other
VSS
AD19
Power/Other
D[54]#
AD20
Source Synch
Input/
Output
D[59]#
AD21
Source Synch
Input/
Output
VSS
AD22
Power/Other
D[61]#
AD23
Source Synch
Input/
Output
D[49]#
AD24
Source Synch
Input/
Output
VSS
AD25
Power/Other
GTLREF
AD26
Power/Other
VSS
AE1
Power/Other
VID[6]
AE2
CMOS
Output
VID[4]
AE3
CMOS
Output
VSS
AE4
Power/Other
Input
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 6 of 17)
Pin
Number
Signal
Buffer Type
Direction
VID[2]
AE5
CMOS
Output
PSI#
AE6
CMOS
VSSSENSE
AE7
Power/Other
Pin Name
Table 17.
Pin Listing by Pin Number
(Sheet 7 of 17)
Pin
Number
Signal
Buffer Type
VSS
AF13
Power/Other
Output
VCC
AF14
Power/Other
Output
VCC
AF15
Power/Other
Pin Name
Direction
VSS
AE8
Power/Other
VSS
AF16
Power/Other
VCC
AE9
Power/Other
VCC
AF17
Power/Other
VCC
AE10
Power/Other
VCC
AF18
Power/Other
VSS
AE11
Power/Other
VSS
AF19
Power/Other
VCC
AE12
Power/Other
VCC
AF20
Power/Other
VCC
AE13
Power/Other
VSS
AF21
Power/Other
VSS
AE14
Power/Other
D[62]#
AF22
Source Synch
VCC
AE15
Power/Other
Input/
Output
VSS
AE16
Power/Other
D[56]#
AF23
Source Synch
Input/
Output
VCC
AE17
Power/Other
VCC
AE18
Power/Other
DSTBP[3]#
AF24
Source Synch
Input/
Output
VSS
AE19
Power/Other
VSS
AF25
Power/Other
VCC
AE20
Power/Other
TEST4
AF26
Test
RSVD
B2
Reserved
INIT#
B3
CMOS
Input
LINT1
B4
CMOS
Input
DPSLP#
B5
CMOS
Input
VSS
B6
Power/Other
VCC
B7
Power/Other
VSS
B8
Power/Other
D[58]#
AE21
Source Synch
Input/
Output
Input/
Output
D[55]#
AE22
Source Synch
VSS
AE23
Power/Other
D[48]#
AE24
Source Synch
Input/
Output
DSTBN[3]#
AE25
Source Synch
Input/
Output
VSS
AE26
Power/Other
TEST5
AF1
Test
VSS
AF2
Power/Other
VID[5]
AF3
CMOS
Output
VID[3]
AF4
CMOS
Output
VID[1]
AF5
CMOS
Output
VSS
AF6
Power/Other
VCCSENSE
AF7
Power/Other
VSS
AF8
Power/Other
VCC
AF9
Power/Other
VCC
AF10
Power/Other
VSS
AF11
Power/Other
VCC
AF12
Power/Other
Datasheet
VCC
B9
Power/Other
VCC
B10
Power/Other
VSS
B11
Power/Other
VCC
B12
Power/Other
VSS
B13
Power/Other
VCC
B14
Power/Other
VCC
B15
Power/Other
VSS
B16
Power/Other
VCC
B17
Power/Other
VCC
B18
Power/Other
VSS
B19
Power/Other
VCC
B20
Power/Other
VSS
B21
Power/Other
63
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 8 of 17)
Pin
Number
Signal
Buffer Type
Direction
BSEL[0]
B22
CMOS
Output
BSEL[1]
B23
CMOS
Output
VSS
B24
Pin Name
Table 17.
Pin Listing by Pin Number
(Sheet 9 of 17)
Pin
Number
Signal
Buffer Type
Direction
STPCLK#
D5
CMOS
Input
PWRGOOD
D6
CMOS
Input
Power/Other
SLP#
D7
CMOS
Input
Pin Name
THRMDC
B25
Power/Other
VSS
D8
Power/Other
VCCA
B26
Power/Other
VCC
D9
Power/Other
RESET#
C1
Common
Clock
VCC
D10
Power/Other
VSS
D11
Power/Other
VSS
C2
Power/Other
VCC
D12
Power/Other
RSVD
C3
Reserved
VSS
D13
Power/Other
IGNNE#
C4
CMOS
VCC
D14
Power/Other
VSS
C5
Power/Other
VCC
D15
Power/Other
LINT0
C6
CMOS
Input
THERMTRIP
#
C7
Open Drain
Output
VSS
C8
Power/Other
VCC
C9
Power/Other
VCC
C10
Power/Other
VSS
C11
Power/Other
VCC
C12
Power/Other
VCC
C13
Power/Other
VSS
C14
Power/Other
VCC
C15
Power/Other
VSS
C16
VCC
Input
Input
VSS
D16
Power/Other
VCC
D17
Power/Other
VCC
D18
Power/Other
VSS
D19
Power/Other
IERR#
D20
Open Drain
Output
Input/
Output
PROCHOT#
D21
Open Drain
RSVD
D22
Reserved
VSS
D23
Power/Other
DPWR#
D24
Common
Clock
Power/Other
TEST2
D25
Test
C17
Power/Other
VSS
D26
Power/Other
VCC
C18
Power/Other
DBSY#
E1
VSS
C19
Power/Other
Common
Clock
Input/
Output
DBR#
C20
CMOS
Output
BNR#
E2
Common
Clock
Input/
Output
BSEL[2]
C21
CMOS
Output
VSS
E3
Power/Other
VSS
C22
Power/Other
TEST1
C23
Test
HITM#
E4
Common
Clock
Input/
Output
TEST3
C24
Test
DPRSTP#
E5
CMOS
Input
VSS
C25
Power/Other
VSS
E6
Power/Other
VCCA
C26
Power/Other
VCC
E7
Power/Other
VSS
D1
Power/Other
VSS
E8
Power/Other
RSVD
D2
Reserved
VCC
E9
Power/Other
RSVD
D3
Reserved
VCC
E10
Power/Other
VSS
D4
Power/Other
VSS
E11
Power/Other
64
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 10 of 17)
Pin
Number
Signal
Buffer Type
VCC
E12
Power/Other
VCC
E13
VSS
Table 17.
Pin Listing by Pin Number
(Sheet 11 of 17)
Pin
Number
Signal
Buffer Type
VCC
F18
Power/Other
Power/Other
VSS
F19
Power/Other
E14
Power/Other
VCC
F20
Power/Other
VCC
E15
Power/Other
DRDY#
F21
VSS
E16
Power/Other
Common
Clock
VCC
E17
Power/Other
VSS
F22
Power/Other
VCC
E18
Power/Other
D[4]#
F23
Source Synch
Input/
Output
D[1]#
F24
Source Synch
Input/
Output
VSS
F25
Power/Other
D[13]#
F26
Source Synch
VSS
G1
Power/Other
TRDY#
G2
Common
Clock
Input
RS[2]#
G3
Common
Clock
Input
VSS
G4
Power/Other
BPRI#
G5
Common
Clock
Input
HIT#
G6
Common
Clock
Input/
Output
VCCP
G21
Power/Other
D[3]#
G22
Source Synch
VSS
G23
Power/Other
D[9]#
G24
Source Synch
Input/
Output
D[5]#
G25
Source Synch
Input/
Output
VSS
G26
Power/Other
ADS#
H1
Common
Clock
Input/
Output
REQ[1]#
H2
Source Synch
Input/
Output
VSS
H3
Power/Other
LOCK#
H4
Common
Clock
Input/
Output
DEFER#
H5
Common
Clock
Input
Pin Name
Direction
VSS
E19
Power/Other
VCC
E20
Power/Other
VSS
E21
Power/Other
D[0]#
E22
Source Synch
Input/
Output
D[7]#
E23
Source Synch
Input/
Output
VSS
E24
Power/Other
D[6]#
E25
Source Synch
Input/
Output
D[2]#
E26
Source Synch
Input/
Output
BR0#
F1
Common
Clock
Input/
Output
VSS
F2
Power/Other
RS[0]#
F3
Common
Clock
RS[1]#
F4
Common
Clock
VSS
F5
Power/Other
RSVD
F6
Reserved
VCC
F7
Power/Other
VSS
F8
Power/Other
VCC
F9
Power/Other
VCC
F10
Power/Other
VSS
F11
Power/Other
VCC
F12
Power/Other
VSS
F13
Power/Other
VCC
F14
Power/Other
VCC
F15
Power/Other
VSS
F16
Power/Other
VCC
F17
Power/Other
Datasheet
Input
Pin Name
Input
Direction
Input/
Output
Input/
Output
Input/
Output
65
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 12 of 17)
Pin
Number
Signal
Buffer Type
VSS
H6
Power/Other
VSS
H21
Power/Other
D[12]#
H22
Source Synch
Pin Name
Direction
Input/
Output
Input/
Output
D[15]#
H23
Source Synch
VSS
H24
Power/Other
DINV[0]#
H25
Source Synch
Input/
Output
Table 17.
Pin Listing by Pin Number
(Sheet 13 of 17)
Pin
Number
Signal
Buffer Type
VSS
K23
Power/Other
D[8]#
K24
Source Synch
Input/
Output
D[17]#
K25
Source Synch
Input/
Output
VSS
K26
Power/Other
REQ[4]#
L1
Source Synch
Input/
Output
A[13]#
L2
Source Synch
Input/
Output
VSS
L3
Power/Other
A[5]#
L4
Source Synch
Input/
Output
A[4]#
L5
Source Synch
Input/
Output
VSS
L6
Power/Other
VSS
L21
Power/Other
D[22]#
L22
Source Synch
Input/
Output
D[20]#
L23
Source Synch
Input/
Output
VSS
L24
Power/Other
Pin Name
Direction
DSTBP[0]#
H26
Source Synch
Input/
Output
A[9]#
J1
Source Synch
Input/
Output
VSS
J2
Power/Other
REQ[3]#
J3
Source Synch
Input/
Output
A[3]#
J4
Source Synch
Input/
Output
VSS
J5
Power/Other
VCCP
J6
Power/Other
VCCP
J21
Power/Other
VSS
J22
Power/Other
D[11]#
J23
Source Synch
Input/
Output
D[29]#
L25
Source Synch
Input/
Output
D[10]#
J24
Source Synch
Input/
Output
DSTBN[1]#
L26
Source Synch
Input/
Output
VSS
J25
Power/Other
ADSTB[0]#
M1
Source Synch
Input/
Output
DSTBN[0]#
J26
Source Synch
VSS
M2
Power/Other
VSS
K1
Power/Other
A[7]#
M3
Source Synch
REQ[2]#
K2
Source Synch
RSVD
M4
Reserved
VSS
M5
Power/Other
VCCP
M6
Power/Other
VCCP
M21
Power/Other
VSS
M22
Power/Other
D[23]#
M23
Source Synch
Input/
Output
D[21]#
M24
Source Synch
Input/
Output
VSS
M25
Power/Other
REQ[0]#
K3
Source Synch
VSS
K4
Power/Other
A[6]#
K5
Source Synch
VCCP
K6
Power/Other
VCCP
K21
Power/Other
D[14]#
66
K22
Source Synch
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 14 of 17)
Pin
Number
Signal
Buffer Type
Direction
DSTBP[1]#
M26
Source Synch
Input/
Output
VSS
N1
Power/Other
A[8]#
N2
Source Synch
Input/
Output
A[10]#
N3
Source Synch
Input/
Output
Pin Name
VSS
N4
Power/Other
RSVD
N5
Reserved
VCCP
N6
Power/Other
VCCP
N21
Power/Other
D[16]#
N22
Source Synch
VSS
N23
Power/Other
DINV[1]#
N24
Source Synch
Input/
Output
D[31]#
N25
Source Synch
Input/
Output
VSS
N26
Power/Other
A[15]#
P1
Source Synch
Input/
Output
Input/
Output
A[12]#
P2
Source Synch
VSS
P3
Power/Other
Input/
Output
A[14]#
P4
Source Synch
Input/
Output
A[11]#
P5
Source Synch
Input/
Output
VSS
P6
Power/Other
VSS
P21
Power/Other
D[26]#
P22
Source Synch
Input/
Output
D[25]#
P23
Source Synch
Input/
Output
VSS
P24
Power/Other
D[24]#
P25
Source Synch
Input/
Output
D[18]#
P26
Source Synch
Input/
Output
A[16]#
R1
Source Synch
Input/
Output
Datasheet
Table 17.
Pin Listing by Pin Number
(Sheet 15 of 17)
Pin
Number
Signal
Buffer Type
VSS
R2
Power/Other
A[19]#
R3
Source Synch
Input/
Output
A[24]#
R4
Source Synch
Input/
Output
Pin Name
Direction
VSS
R5
Power/Other
VCCP
R6
Power/Other
VCCP
R21
Power/Other
VSS
R22
Power/Other
D[19]#
R23
Source Synch
Input/
Output
D[28]#
R24
Source Synch
Input/
Output
VSS
R25
Power/Other
COMP[0]
R26
Power/Other
VSS
T1
Power/Other
RSVD
T2
Reserved
A[26]#
T3
Source Synch
VSS
T4
Power/Other
A[25]#
T5
Source Synch
VCCP
T6
Power/Other
VCCP
T21
Power/Other
D[37]#
T22
Source Synch
VSS
T23
Power/Other
D[27]#
T24
Source Synch
Input/
Output
D[30]#
T25
Source Synch
Input/
Output
VSS
T26
Power/Other
A[23]#
U1
Source Synch
Input/
Output
A[30]#
U2
Source Synch
Input/
Output
VSS
U3
Power/Other
A[21]#
U4
Source Synch
Input/
Output
Input/
Output
Input/
Output
Input/
Output
Input/
Output
67
Package Mechanical Specifications and Pin Information
Table 17.
Pin Listing by Pin Number
(Sheet 16 of 17)
Pin
Number
Signal
Buffer Type
Direction
U5
Source Synch
Input/
Output
VSS
U6
Power/Other
VSS
U21
Power/Other
DINV[2]#
U22
Source Synch
Input/
Output
Input/
Output
Pin Name
A[18]#
D[39]#
U23
Source Synch
VSS
U24
Power/Other
D[38]#
U25
Source Synch
Input/
Output
COMP[1]
U26
Power/Other
Input/
Output
ADSTB[1]#
V1
Source Synch
Input/
Output
VSS
V2
Power/Other
RSVD
V3
Reserved
A[31]#
V4
Source Synch
VSS
V5
Power/Other
VCCP
V6
Power/Other
VCCP
V21
Power/Other
VSS
V22
Power/Other
Input/
Output
D[36]#
V23
Source Synch
Input/
Output
D[34]#
V24
Source Synch
Input/
Output
VSS
V25
Power/Other
D[35]#
V26
Source Synch
VSS
W1
Power/Other
A[27]#
W2
Source Synch
Input/
Output
A[32]#
W3
Source Synch
Input/
Output
VSS
W4
Power/Other
A[28]#
W5
Source Synch
Input/
Output
A[20]#
W6
Source Synch
Input/
Output
VCCP
W21
Power/Other
68
Table 17.
Pin Listing by Pin Number
(Sheet 17 of 17)
Pin
Number
Signal
Buffer Type
Direction
D[41]#
W22
Source Synch
Input/
Output
VSS
W23
Power/Other
D[43]#
W24
Source Synch
Input/
Output
D[44]#
W25
Source Synch
Input/
Output
VSS
W26
Power/Other
COMP[3]
Y1
Power/Other
Input/
Output
A[17]#
Y2
Source Synch
Input/
Output
VSS
Y3
Power/Other
A[29]#
Y4
Source Synch
Input/
Output
A[22]#
Y5
Source Synch
Input/
Output
VSS
Y6
Power/Other
VSS
Y21
Power/Other
D[32]#
Y22
Source Synch
Input/
Output
D[42]#
Y23
Source Synch
Input/
Output
Pin Name
VSS
Y24
Power/Other
D[40]#
Y25
Source Synch
Input/
Output
DSTBN[2]#
Y26
Source Synch
Input/
Output
Input/
Output
Datasheet
Package Mechanical Specifications and Pin Information
4.3
Alphabetical Signals Reference
Table 18.
Signal Description (Sheet 1 of 7)
Name
A[35:3]#
A20M#
Type
Description
Input/
Output
A[35:3]# (Address) define a 236-byte physical memory address space. In subphase 1 of the address phase, these pins transmit the address of a transaction. In
sub-phase 2, these pins transmit transaction type information. These signals must
connect the appropriate pins of both agents on the processor FSB. A[35:3]# are
source synchronous signals and are latched into the receiving buffers by
ADSTB[1:0]#. Address signals are used as straps which are sampled before
RESET# is deasserted.
Input
If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit
20 (A20#) before looking up a line in any internal cache and before driving a read/
write transaction on the bus. Asserting A20M# emulates the 8086 processor's
address wrap-around at the 1-Mbyte boundary. Assertion of A20M# is only
supported in real mode.
A20M# is an asynchronous signal. However, to ensure recognition of this signal
following an Input/Output write instruction, it must be valid along with the TRDY#
assertion of the corresponding Input/Output Write bus transaction.
ADS#
Input/
Output
ADS# (Address Strobe) is asserted to indicate the validity of the transaction
address on the A[35:3]# and REQ[4:0]# pins. All bus agents observe the ADS#
activation to begin parity checking, protocol checking, address decode, internal
snoop, or deferred reply ID match operations associated with the new transaction.
Address strobes are used to latch A[35:3]# and REQ[4:0]# on their rising and
falling edges. Strobes are associated with signals as shown below.
ADSTB[1:0]#
BCLK[1:0]
BNR#
BPM[2:1]#
BPM[3,0]#
Input/
Output
Input
Input/
Output
Output
Input/
Output
Signals
Associated Strobe
REQ[4:0]#, A[16:3]#
ADSTB[0]#
A[35:17]#
ADSTB[1]#
The differential pair BCLK (Bus Clock) determines the FSB frequency. All FSB
agents must receive these signals to drive their outputs and latch their inputs.
All external timing parameters are specified with respect to the rising edge of
BCLK0 crossing VCROSS.
BNR# (Block Next Request) is used to assert a bus stall by any bus agent who is
unable to accept new bus transactions. During a bus stall, the current bus owner
cannot issue any new transactions.
BPM[3:0]# (Breakpoint Monitor) are breakpoint and performance monitor signals.
They are outputs from the processor which indicate the status of breakpoints and
programmable counters used for monitoring processor performance. BPM[3:0]#
should connect the appropriate pins of all processor FSB agents.This includes
debug or performance monitoring tools.
BPRI#
Input
BPRI# (Bus Priority Request) is used to arbitrate for ownership of the FSB. It must
connect the appropriate pins of both FSB agents. Observing BPRI# active (as
asserted by the priority agent) causes the other agent to stop issuing new
requests, unless such requests are part of an ongoing locked operation. The
priority agent keeps BPRI# asserted until all of its requests are completed, then
releases the bus by deasserting BPRI#.
BR0#
Input/
Output
BR0# is used by the processor to request the bus. The arbitration is done between
processor (Symmetric Agent) and (G)MCH (High Priority Agent).
Datasheet
69
Package Mechanical Specifications and Pin Information
Table 18.
Name
Signal Description (Sheet 2 of 7)
Type
Description
BSEL[2:0]
Output
BSEL[2:0] (Bus Select) are used to select the processor input clock frequency.
Table 3 defines the possible combinations of the signals and the frequency
associated with each combination. The required frequency is determined by the
processor, chipset and clock synthesizer. All agents must operate at the same
frequency.
COMP[3:0]
Analog
COMP[3:0] must be terminated on the system board using precision (1%
tolerance) resistors.
D[63:0]# (Data) are the data signals. These signals provide a 64-bit data path
between the FSB agents, and must connect the appropriate pins on both agents.
The data driver asserts DRDY# to indicate a valid data transfer.
D[63:0]# are quad-pumped signals and are driven four times in a common clock
period. D[63:0]# are latched off the falling edge of both DSTBP[3:0]# and
DSTBN[3:0]#. Each group of 16 data signals corresponds to a pair of one DSTBP#
and one DSTBN#. The following table shows the grouping of data signals to data
strobes and DINV#.
Quad-Pumped Signal Groups
D[63:0]#
Input/
Output
Data
Group
DSTBN#/
DSTBP#
DINV#
D[15:0]#
0
0
D[31:16]#
1
1
D[47:32]#
2
2
D[63:48]#
3
3
Furthermore, the DINV# pins determine the polarity of the data signals. Each
group of 16 data signals corresponds to one DINV# signal. When the DINV# signal
is active, the corresponding data group is inverted and therefore sampled active
high.
DBR#
Output
DBR# (Data Bus Reset) is used only in processor systems where no debug port is
implemented on the system board. DBR# is used by a debug port interposer so
that an in-target probe can drive system reset. If a debug port is implemented in
the system, DBR# is a no-connect in the system. DBR# is not a processor signal.
DBSY#
Input/
Output
DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on
the FSB to indicate that the data bus is in use. The data bus is released after
DBSY# is deasserted. This signal must connect the appropriate pins on both FSB
agents.
DEFER#
70
Input
DEFER# is asserted by an agent to indicate that a transaction cannot be
guaranteed in-order completion. Assertion of DEFER# is normally the responsibility
of the addressed memory or Input/Output agent. This signal must connect the
appropriate pins of both FSB agents.
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.
Name
Signal Description (Sheet 3 of 7)
Type
Description
DINV[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity
of the D[63:0]# signals. The DINV[3:0]# signals are activated when the data on
the data bus is inverted. The bus agent inverts the data bus signals if more than
half the bits, within the covered group, would change level in the next cycle.
DINV[3:0]# Assignment To Data Bus
DINV[3:0]#
Input/
Output
Bus Signal
Data Bus
Signals
DINV[3]#
D[63:48]#
DINV[2]#
D[47:32]#
DINV[1]#
D[31:16]#
DINV[0]#
D[15:0]#
DPRSTP#
Input
DPRSTP# when asserted on the platform causes the processor to transition from
the Deep Sleep State to the Deeper Sleep state. In order to return to the Deep
Sleep State, DPRSTP# must be deasserted. DPRSTP# is driven by the Intel
82801HBM ICH8M I/O Controller Hub based chipset.
DPSLP#
Input
DPSLP# when asserted on the platform causes the processor to transition from the
Sleep State to the Deep Sleep state. In order to return to the Sleep State, DPSLP#
must be deasserted. DPSLP# is driven by the Intel 82801HBM ICH8M chipset.
DPWR#
Input/
Output
DPWR# is a control signal used by the chipset to reduce power on the processor
data bus input buffers. The processor drives this pin during dynamic FSB frequency
switching.
DRDY#
Input/
Output
DRDY# (Data Ready) is asserted by the data driver on each data transfer,
indicating valid data on the data bus. In a multi-common clock data transfer,
DRDY# may be deasserted to insert idle clocks. This signal must connect the
appropriate pins of both FSB agents.
Data strobe used to latch in D[63:0]#.
DSTBN[3:0]#
Input/
Output
Signals
Associated
Strobe
D[15:0]#, DINV[0]#
DSTBN[0]#
D[31:16]#, DINV[1]#
DSTBN[1]#
D[47:32]#, DINV[2]#
DSTBN[2]#
D[63:48]#, DINV[3]#
DSTBN[3]#
Data strobe used to latch in D[63:0]#.
DSTBP[3:0]#
Datasheet
Input/
Output
Signals
Associated Strobe
D[15:0]#, DINV[0]#
DSTBP[0]#
D[31:16]#, DINV[1]#
DSTBP[1]#
D[47:32]#, DINV[2]#
DSTBP[2]#
D[63:48]#, DINV[3]#
DSTBP[3]#
71
Package Mechanical Specifications and Pin Information
Table 18.
Name
FERR#/PBE#
Signal Description (Sheet 4 of 7)
Type
Output
Description
FERR# (Floating-point Error)/PBE#(Pending Break Event) is a multiplexed signal
and its meaning is qualified with STPCLK#. When STPCLK# is not asserted, FERR#/
PBE# indicates a floating point when the processor detects an unmasked floatingpoint error. FERR# is similar to the ERROR# signal on the Intel 387 coprocessor,
and is included for compatibility with systems using MS-DOS*-type floating-point
error reporting. When STPCLK# is asserted, an assertion of FERR#/PBE# indicates
that the processor has a pending break event waiting for service. The assertion of
FERR#/PBE# indicates that the processor should be returned to the Normal state.
When FERR#/PBE# is asserted, indicating a break event, it remains asserted until
STPCLK# is deasserted. Assertion of PREQ# when STPCLK# is active also causes
an FERR# break event.
For additional information on the pending break event functionality, including
identification of support of the feature and enable/disable information, refer to
Volumes 3A and 3B of the Intel® 64 and IA-32 Architectures Software Developer’s
Manual and the Intel® Processor Identification and CPUID Instruction application
note.
GTLREF
Input
HIT#
Input/
Output
HITM#
Input/
Output
IERR#
IGNNE#
Output
Input
GTLREF determines the signal reference level for AGTL+ input pins. GTLREF should
be set at 2/3 VCCP. GTLREF is used by the AGTL+ receivers to determine if a signal
is a logical 0 or logical 1.
HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction snoop operation
results. Either FSB agent may assert both HIT# and HITM# together to indicate
that it requires a snoop stall, which can be continued by reasserting HIT# and
HITM# together.
IERR# (Internal Error) is asserted by a processor as the result of an internal error.
Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the
FSB. This transaction may optionally be converted to an external error signal (e.g.,
NMI) by system core logic. The processor keeps IERR# asserted until the assertion
of RESET#, BINIT#, or INIT#.
IGNNE# (Ignore Numeric Error) is asserted to force the processor to ignore a
numeric error and continue to execute noncontrol floating-point instructions. If
IGNNE# is deasserted, the processor generates an exception on a noncontrol
floating-point instruction if a previous floating-point instruction caused an error.
IGNNE# has no effect when the NE bit in control register 0 (CR0) is set.
IGNNE# is an asynchronous signal. However, to ensure recognition of this signal
following an Input/Output write instruction, it must be valid along with the TRDY#
assertion of the corresponding Input/Output Write bus transaction.
INIT#
Input
INIT# (Initialization), when asserted, resets integer registers inside the processor
without affecting its internal caches or floating-point registers. The processor then
begins execution at the power-on Reset vector configured during power-on
configuration. The processor continues to handle snoop requests during INIT#
assertion. INIT# is an asynchronous signal. However, to ensure recognition of this
signal following an Input/Output Write instruction, it must be valid along with the
TRDY# assertion of the corresponding Input/Output Write bus transaction. INIT#
must connect the appropriate pins of both FSB agents.
If INIT# is sampled active on the active to inactive transition of RESET#, then the
processor executes its Built-in Self-Test (BIST)
72
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.
Name
LINT[1:0]
Signal Description (Sheet 5 of 7)
Type
Description
Input
LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins of all APIC Bus
agents. When the APIC is disabled, the LINT0 signal becomes INTR, a maskable
interrupt request signal, and LINT1 becomes NMI, a nonmaskable interrupt. INTR
and NMI are backward compatible with the signals of those names on the Intel®
Pentium® processor. Both signals are asynchronous.
Both of these signals must be software configured via BIOS programming of the
APIC register space to be used either as NMI/INTR or LINT[1:0]. Because the APIC
is enabled by default after Reset, operation of these pins as LINT[1:0] is the default
configuration.
LOCK#
Input/
Output
PRDY#
Output
PREQ#
Input
PROCHOT#
Input/
Output
LOCK# indicates to the system that a transaction must occur atomically. This signal
must connect the appropriate pins of both FSB agents. For a locked sequence of
transactions, LOCK# is asserted from the beginning of the first transaction to the
end of the last transaction.
When the priority agent asserts BPRI# to arbitrate for ownership of the FSB, it
waits until it observes LOCK# deasserted. This enables symmetric agents to retain
ownership of the FSB throughout the bus locked operation and ensure the
atomicity of lock.
Probe Ready signal used by debug tools to determine processor debug readiness.
Probe Request signal used by debug tools to request debug operation of the
processor.
As an output, PROCHOT# (Processor Hot) goes active when the processor
temperature monitoring sensor detects that the processor has reached its
maximum safe operating temperature. This indicates that the processor Thermal
Control Circuit (TCC) has been activated, if enabled. As an input, assertion of
PROCHOT# by the system activates the TCC, if enabled. The TCC remains active
until the system deasserts PROCHOT#.
By default PROCHOT# is configured as an output. The processor must be enabled
via the BIOS for PROCHOT# to be configured as bidirectional.
This signal may require voltage translation on the motherboard.
PSI#
PWRGOOD
Output
Input
Processor Power Status Indicator signal. This signal is asserted when the processor
is in both in the Normal state (HFM to LFM) and in lower power states (Deep Sleep
and Deeper Sleep).
PWRGOOD (Power Good) is a processor input. The processor requires this signal to
be a clean indication that the clocks and power supplies are stable and within their
specifications. ‘Clean’ implies that the signal remains low (capable of sinking
leakage current), without glitches, from the time that the power supplies are
turned on until they come within specification. The signal must then transition
monotonically to a high state. PWRGOOD can be driven inactive at any time, but
clocks and power must again be stable before a subsequent rising edge of
PWRGOOD.
The PWRGOOD signal must be supplied to the processor; it is used to protect
internal circuits against voltage sequencing issues. It should be driven high
throughout boundary scan operation.
REQ[4:0]#
Datasheet
Input/
Output
REQ[4:0]# (Request Command) must connect the appropriate pins of both FSB
agents. They are asserted by the current bus owner to define the currently active
transaction type. These signals are source synchronous to ADSTB[0]#.
73
Package Mechanical Specifications and Pin Information
Table 18.
Name
Signal Description (Sheet 6 of 7)
Type
Description
RESET#
Input
Asserting the RESET# signal resets the processor to a known state and invalidates
its internal caches without writing back any of their contents. For a power-on
Reset, RESET# must stay active for at least two milliseconds after VCC and BCLK
have reached their proper specifications. On observing active RESET#, both FSB
agents deasserts their outputs within two clocks. All processor straps must be valid
within the specified setup time before RESET# is deasserted. There is a 55-Ω
(nominal) on die pull-up resistor on this signal.
RS[2:0]#
Input
RS[2:0]# (Response Status) are driven by the response agent (the agent
responsible for completion of the current transaction), and must connect the
appropriate pins of both FSB agents.
RSVD
SLP#
SMI#
Reserved
/No
Connect
These pins are RESERVED and must be left unconnected on the board. However, it
is recommended that routing channels to these pins on the board be kept open for
possible future use.
Input
SLP# (Sleep), when asserted in Stop-Grant state, causes the processor to enter
the Sleep state. During Sleep state, the processor stops providing internal clock
signals to all units, leaving only the Phase-Locked Loop (PLL) still operating.
Processors in this state does not recognize snoops or interrupts. The processor
recognizes only assertion of the RESET# signal, deassertion of SLP#, and removal
of the BCLK input while in Sleep state. If SLP# is deasserted, the processor exits
Sleep state and returns to Stop-Grant state, restarting its internal clock signals to
the bus and processor core units. If DPSLP# is asserted while in the Sleep state,
the processor exits the Sleep state and transition to the Deep Sleep state.
Input
SMI# (System Management Interrupt) is asserted asynchronously by system logic.
On accepting a System Management Interrupt, the processor saves the current
state and enters System Management Mode (SMM). An SMI Acknowledge
transaction is issued and the processor begins program execution from the SMM
handler.
If an SMI# is asserted during the deassertion of RESET#, then the processor
tristates its outputs.
STPCLK#
Input
STPCLK# (Stop Clock), when asserted, causes the processor to enter a low power
Stop-Grant state. The processor issues a Stop-Grant Acknowledge transaction, and
stops providing internal clock signals to all processor core units except the FSB and
APIC units. The processor continues to snoop bus transactions and service
interrupts while in Stop-Grant state. When STPCLK# is deasserted, the processor
restarts its internal clock to all units and resumes execution. The assertion of
STPCLK# has no effect on the bus clock; STPCLK# is an asynchronous input.
TCK
Input
TCK (Test Clock) provides the clock input for the processor Test Bus (also known as
the Test Access Port).
TDI
Input
TDI (Test Data In) transfers serial test data into the processor. TDI provides the
serial input needed for JTAG specification support.
TDO
Output
TDO (Test Data Out) transfers serial test data out of the processor. TDO provides
the serial output needed for JTAG specification support.
Input
TEST1 and TEST2 must have a stuffing option of separate pulldown resistors to
VSS. For the purpose of testability, route the TEST3 and TEST5 signals through a
ground-referenced Zo=55 ohm trace that ends in a via that is near a GND via and
is accessible through an oscilloscope connection.
THRMDA
Other
Thermal Diode Anode.
THRMDC
Other
Thermal Diode Cathode.
TEST1, TEST2,
TEST3,
TEST4,
TEST5,
TEST6
74
Datasheet
Package Mechanical Specifications and Pin Information
Table 18.
Name
Signal Description (Sheet 7 of 7)
Type
Description
Output
The processor protects itself from catastrophic overheating by use of an internal
thermal sensor. This sensor is set well above the normal operating temperature to
ensure that there are no false trips. The processor stops all execution when the
junction temperature exceeds approximately 125°C. This is signalled to the system
by the THERMTRIP# (Thermal Trip) pin.
TMS
Input
TMS (Test Mode Select) is a JTAG specification support signal used by debug tools.
TRDY#
Input
TRDY# (Target Ready) is asserted by the target to indicate that it is ready to
receive a write or implicit writeback data transfer. TRDY# must connect the
appropriate pins of both FSB agents.
TRST#
Input
TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven
low during power on Reset.
VCC
Input
Processor core power supply.
VSS
Input
Processor core ground node.
VCCA
Input
VCCA provides isolated power for the internal processor core PLL’s.
VCCP
Input
Processor I/O Power Supply.
THERMTRIP#
Output
VCC_SENSE together with VSS_SENSE are voltage feedback signals to Intel MVP-6
that control the 2.1-mΩ loadline at the processor die. It should be used to sense
voltage near the silicon with little noise.
VID[6:0]
Output
VID[6:0] (Voltage ID) pins are used to support automatic selection of power supply
voltages (VCC). Unlike some previous generations of processors, these are CMOS
signals that are driven by the processor. The voltage supply for these pins must be
valid before the VR can supply Vcc to the processor. Conversely, the VR output
must be disabled until the voltage supply for the VID pins becomes valid. The VID
pins are needed to support the processor voltage specification variations. See
Table 2 for definitions of these pins. The VR must supply the voltage that is
requested by the pins, or disable itself.
VSS_SENSE
Output
VSS_SENSE together with VCC_SENSE are voltage feedback signals to Intel MVP-6
that control the 2.1-mΩ loadline at the processor die. It should be used to sense
ground near the silicon with little noise.
VCC_SENSE
§
Datasheet
75
Package Mechanical Specifications and Pin Information
76
Datasheet
Thermal Specifications and Design Considerations
5
Thermal Specifications and
Design Considerations
Maintaining the proper thermal environment is key to reliable, long-term system
operation. A complete thermal solution includes both component and system level
thermal management features. The system/processor thermal solution should be
designed so that the processor remains within the minimum and maximum junction
temperature (Tj) specifications at the corresponding thermal design power (TDP) value
listed in Table 19 through Table 20.
Caution:
Operating the processor outside these limits may result in permanent damage to the
processor and potentially other components in the system.
Table 19.
Power Specifications for the Intel Core 2 Duo Processor - Standard Voltage
Symbol
TDP
Processor
Number
Core Frequency & Voltage
PSGNT
Unit
Notes
T7800
2.6 GHz & HFM VCC
35
T7700
2.4 GHz & HFM VCC
35
1, 4, 5, 6, 9
T7500
2.2 GHz & HFM VCC
35
1, 4, 5, 6, 9
T7300
2.0 GHz & HFM VCC
35
T7250
2.0 GHz & HFM VCC
35
T7100
1.8 GHz & HFM VCC
35
1.2 GHZ & LFM VCC
25
0.80 GHZ & SuperLFM VCC
12
Symbol
PAH,
Thermal Design
Power
Parameter
Min
Typ
W
1, 4, 5, 6, 9
1, 4, 5, 6, 10
Max
Unit
13.5
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at HFM VCC
at SuperLFM VCC
6.9
Sleep Power
PSLP
12.9
at HFM VCC
at SuperLFM VCC
6.7
Deep Sleep Power
PDSLP
at HFM VCC
7.7
at SuperLFM VCC
4.3
PDPRSLP
Deeper Sleep Power
2.0
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep Power
1.2
W
2, 8
TJ
Junction Temperature
100
°C
3, 4
0
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached. Refer to Section 5.1 for details.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
Datasheet
77
Thermal Specifications and Design Considerations
5.
6.
7.
8.
9.
10.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode is lesser than TDP in HFM.
At Tj of 100oC
At Tj of 50oC
At Tj of 35oC
4-M L2 cache
2-M L2 cache
Table 20.
Symbol
TDP
Power Specifications for the Intel Core 2 Duo Processor - Low Voltage
Processor
Number
PSGNT
Thermal Design
Power
L7700
1.8 GHz & HFM VCC
17
L7500
1.6 GHz & HFM VCC
17
L7300
1.4 GHz & HFM VCC
17
1.2 GHZ & LFM VCC
16.1
0.80 GHZ & SuperLFM VCC
10.0
Symbol
PAH,
Core Frequency & Voltage
Parameter
Min
Typ
Unit
Notes
W
1, 4, 5, 6, 9
Max
Unit
at HFM VCC
5.6
W
2, 5, 7
at SuperLFM VCC
3.9
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
Sleep Power
PSLP
at HFM VCC
5.3
at SuperLFM VCC
3.6
Deep Sleep Power
PDSLP
at HFM VCC
2.8
at SuperLFM VCC
2.3
PDPRSLP
Deeper Sleep Power
1.3
W
2, 8
PDC4
Intel® Enhanced Deeper Sleep Power
0.8
W
2, 8
TJ
Junction Temperature
100
°C
3, 4
0
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached. Refer to Section 5.1 for more details.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode is lesser than TDP in HFM.
6.
At Tj of 100oC.
7.
At Tj of 50oC.
8.
At Tj of 35oC.
9.
4-M L2 cache.
78
Datasheet
Thermal Specifications and Design Considerations
Table 21.
Symbol
TDP
Power Specifications for the Intel Core 2 Duo Processor - Ultra Low Voltage
Processor
Number
PSGNT
Thermal Design
Power
U7700
1.33 GHz & HFM VCC
10
U7600
1.20 GHz & HFM VCC
10
U7500
1.06 GHz & HFM VCC
10
0.80 GHZ & LFM VCC
9.2
Symbol
PAH,
Core Frequency & Voltage
Parameter
Min
Typ
Unit
Notes
W
1, 4, 5, 6, 9
Max
Unit
at HFM VCC
3.1
W
2, 5, 7
at LFM VCC
2.6
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
Sleep Power
PSLP
at HFM VCC
3.0
at LFM VCC
2.5
Deep Sleep Power
PDSLP
at HFM VCC
1.5
at LFM VCC
1.3
PDPRSLP
Deeper Sleep Power
1.0
W
2, 8
PDC4
Intel Enhanced Deeper Sleep Power
0.7
W
2, 8
TJ
Junction Temperature
100
°C
3, 4
0
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached. Refer to Section 5.1 for more details.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Processor TDP requirements in Intel Dynamic Acceleration Technology mode is lesser than TDP in HFM.
6.
At Tj of 100oC.
7.
At Tj of 50oC.
8.
At Tj of 35oC.
9.
2-M L2 cache.
Datasheet
79
Thermal Specifications and Design Considerations
Table 22.
Symbol
TDP
Power Specifications for the Intel Core 2 Extreme Processor
Processor
Number
PSGNT
Thermal Design
Power
X7900
2.8 GHz & HFM VCC
44
X7800
2.6 GHz & HFM VCC
44
1.2 GHZ & LFM VCC
35
0.80 GHZ & SuperLFM VCCc
27
Symbol
PAH,
Core Frequency & Voltage
Parameter
Min
Typ
Unit
Notes
W
1, 4, 5, 6, 9
Max
Unit
15.7
W
2, 5, 7
W
2, 5, 7
W
2, 5, 8
Auto Halt, Stop Grant Power
at HFM VCC
at SuperLFM VCC
9.3
Sleep Power
PSLP
15.0
at HFM VCC
at SuperLFM VCC
9.1
Deep Sleep Power
PDSLP
at HFM VCC
9.5
at SuperLFM VCC
6.0
PDPRSLP
Deeper Sleep Power
3.0
W
2, 8
PDC4
Intel Enhanced Deeper Sleep Power
2.5
W
2, 8
TJ
Junction Temperature
100
°C
3, 4
0
NOTES:
1.
The TDP specification should be used to design the processor thermal solution. The TDP is not the
maximum theoretical power the processor can generate.
2.
Not 100% tested. These power specifications are determined by characterization of the processor currents
at higher temperatures and extrapolating the values for the temperature indicated.
3.
As measured by the activation of the on-die Intel Thermal Monitor. The Intel Thermal Monitor’s automatic
mode is used to indicate that the maximum TJ has been reached. Refer to Section 5.1 for more details.
4.
The Intel Thermal Monitor automatic mode must be enabled for the processor to operate within
specifications.
5.
Intel Dynamic Acceleration mode is not supported.
6.
At Tj of 100°C.
7.
At Tj of 50oC.
8.
At Tj of 35°C.
9.
4-M L2 cache.
5.1
Thermal Specifications
The processor incorporates three methods of monitoring die temperature:
• Thermal Diode
• Intel Thermal Monitor
• Digital Thermal Sensor
80
Datasheet
Thermal Specifications and Design Considerations
5.1.1
Thermal Diode
The processor incorporates an on-die PNP transistor whose base emitter junction is
used as a thermal diode, with its collector shorted to ground. The thermal diode can be
read by an off-die analog/digital converter (a thermal sensor) located on the
motherboard or a stand-alone measurement kit. The thermal diode may be used to
monitor the die temperature of the processor for thermal management or
instrumentation purposes but is not a reliable indication that the maximum operating
temperature of the processor has been reached. When using the thermal diode, a
temperature offset value must be read from a processor MSR and applied. See
Section 5.1.2 for more details. Please see Section 5.1.3 for thermal diode usage
recommendation when the PROCHOT# signal is not asserted.
The reading of the external thermal sensor (on the motherboard) connected
to the processor thermal diode signals does not reflect the temperature of the
hottest location on the die. This is due to inaccuracies in the external thermal
sensor, on-die temperature gradients between the location of the thermal diode and the
hottest location on the die, and time based variations in the die temperature
measurement. Time-based variations can occur when the sampling rate of the thermal
diode (by the thermal sensor) is slower than the rate at which the TJ temperature can
change.
Offset between the thermal diode-based temperature reading and the Intel Thermal
Monitor reading may be characterized using the Intel Thermal Monitor’s Automatic
mode activation of the thermal control circuit. This temperature offset must be taken
into account when using the processor thermal diode to implement power management
events. This offset is different than the diode Toffset value programmed into the
processor Model Specific Register (MSR).
Table 23 to Table 26 provide the diode interface and specifications. The diode model
parameters apply to the traditional thermal sensors that use the diode equation to
determine the processor temperature. Transistor model parameters have been added
to support thermal sensors that use the transistor equation method. The Transistor
model may provide more accurate temperature measurements when the diode ideality
factor is closer to the maximum or minimum limits. Contact your external sensor
supplier for recommendations. The thermal diode is separate from the Intel Thermal
Monitor’s thermal sensor and cannot be used to predict the behavior of the Intel
Thermal Monitor.
Table 23.
Datasheet
Thermal Diode Interface
Signal Name
Pin/Ball Number
Signal Description
THERMDA
A24
Thermal diode anode
THERMDC
A25
Thermal diode cathode
81
Thermal Specifications and Design Considerations
Table 24.
Thermal Diode Parameters Using Diode Model
Symbol
IFW
Parameter
Min
Typ
Max
Unit
Notes
200
µA
1
Ω
2, 3, 5
Forward Bias Current
5
n
Diode Ideality Factor
1.000
1.009
1.050
RT
Series Resistance
2.79
4.52
6.24
2, 3, 4
NOTES:
1.
Intel does not support or recommend operation of the thermal diode under reverse bias.
Intel does not support or recommend operation of the thermal diode when the processor
power supplies are not within their specified tolerance range.
2.
Characterized across a temperature range of 50-100°C.
3.
Not 100% tested. Specified by design characterization.
4.
The ideality factor, n, represents the deviation from ideal diode behavior as exemplified by
the diode equation:
IFW = IS * (e
5.
qV /nkT
D
–1)
where IS = saturation current, q = electronic charge, VD = voltage across the diode, k =
Boltzmann Constant, and T = absolute temperature (Kelvin).
The series resistance, RT, is provided to allow for a more accurate measurement of the
junction temperature. RT, as defined, includes the lands of the processor but does not
include any socket resistance or board trace resistance between the socket and the
external remote diode thermal sensor. RT can be used by remote diode thermal sensors
with automatic series resistance cancellation to calibrate out this error term. Another
application is that a temperature offset can be manually calculated and programmed into
an offset register in the remote diode thermal sensors as exemplified by the equation:
Terror = [RT * (N-1) * IFWmin] / [nk/q * ln N]
where Terror = sensor temperature error, N = sensor current ratio, k = Boltzmann
Constant, q = electronic charge.
82
Datasheet
Thermal Specifications and Design Considerations
Table 25.
Thermal Diode Parameters Using Transistor Model
Symbol
Parameter
Min
IFW
Forward Bias Current
IE
Emitter Current
nQ
Transistor Ideality
5
5
0.997
Beta
RT
Typ
1.001
0.3
Series Resistance
2.79
4.52
Max
Unit
Notes
200
μA
1,2
200
μA
1
1.005
3,4,5
0.760
3,4
6.24
Ω
3,6
NOTES:
1.
Intel does not support or recommend operation of the thermal diode under reverse bias.
2.
Same as IFW in Table 24.
3.
Characterized across a temperature range of 50-100°C.
4.
Not 100% tested. Specified by design characterization.
5.
The ideality factor, nQ, represents the deviation from ideal transistor model behavior as
exemplified by the equation for the collector current:
IC = IS * (e
6.
qV
BE
/n kT
Q
–1)
where IS = saturation current, q = electronic charge, VBE = voltage across the transistor
base emitter junction (same nodes as VD), k = Boltzmann Constant, and T = absolute
temperature (Kelvin).
The series resistance, RT, provided in the Diode Model Table (Table 24) can be used for
more accurate readings as needed.
When calculating a temperature based on the thermal diode measurements, a number
of parameters must be either measured or assumed. Most devices measure the diode
ideality and assume a series resistance and ideality trim value, although are capable of
also measuring the series resistance. Calculating the temperature is then accomplished
using the equations listed under Table 24. In most sensing devices, an expected value
for the diode ideality is designed-in to the temperature calculation equation. If the
designer of the temperature sensing device assumes a perfect diode, the ideality value
(also called ntrim) is 1.000. Given that most diodes are not perfect, the designers
usually select an ntrim value that more closely matches the behavior of the diodes in
the processor. If the processor diode ideality deviates from that of the ntrim, each
calculated temperature offsets by a fixed amount. This temperature offset can be
calculated with the equation:
Terror(nf) = Tmeasured * (1 - nactual/ntrim)
where Terror(nf) is the offset in degrees C, Tmeasured is in Kelvin, nactual is the measured
ideality of the diode, and ntrim is the diode ideality assumed by the temperature
sensing device.
5.1.2
Thermal Diode Offset
In order to improve the accuracy of the diode-based temperature measurements, a
temperature offset value (specified as Toffset) is programmed in the processor MSR
which contains thermal diode characterization data. During manufacturing each
processor thermal diode is evaluated for its behavior relative to the theoretical diode.
Using the equation above, the temperature error created by the difference ntrim and the
actual ideality of the particular processor is calculated.
Datasheet
83
Thermal Specifications and Design Considerations
If the ntrim value used to calculate the Toffset differs from the ntrim value used to in a
temperature sensing device, the Terror(nf) may not be accurate. If desired, the Toffset
can be adjusted by calculating nactual and then recalculating the offset using the ntrim as
defined in the temperature sensor manufacturer’s datasheet.
The ntrim used to calculate the Diode Correction Toffset are listed in Table 26.
Table 26.
5.1.3
Thermal Diode ntrim and Diode Correction Toffset
Symbol
Parameter
Value
ntrim
Diode Ideality used to calculate Toffset
1.01
Intel® Thermal Monitor
The Intel Thermal Monitor helps control the processor temperature by activating the
TCC (Thermal Control Circuit) when the processor silicon reaches its maximum
operating temperature. The temperature at which the Intel Thermal Monitor activates
the TCC is not user configurable. Bus traffic is snooped in the normal manner and
interrupt requests are latched (and serviced during the time that the clocks are on)
while the TCC is active.
With a properly designed and characterized thermal solution, it is anticipated that the
TCC would only be activated for very short periods of time when running the most
power intensive applications. The processor performance impact due to these brief
periods of TCC activation is expected to be minor and hence not detectable. An underdesigned thermal solution that is not able to prevent excessive activation of the TCC in
the anticipated ambient environment may cause a noticeable performance loss and
may affect the long-term reliability of the processor. In addition, a thermal solution that
is significantly under-designed may not be capable of cooling the processor even when
the TCC is active continuously.
The Intel Thermal Monitor controls the processor temperature by modulating (starting
and stopping) the processor core clocks or by initiating an Enhanced Intel SpeedStep
Technology transition when the processor silicon reaches its maximum operating
temperature. The Intel Thermal Monitor uses two modes to activate the TCC: automatic
mode and on-demand mode. If both modes are activated, automatic mode takes
precedence.
There are two automatic modes called Intel Thermal Monitor 1 and Intel Thermal
Monitor 2. These modes are selected by writing values to the MSRs of the processor.
After automatic mode is enabled, the TCC activates only when the internal die
temperature reaches the maximum allowed value for operation.
When Intel Thermal Monitor 1 is enabled and a high temperature situation exists, the
clocks modulates by alternately turning the clocks off and on at a 50% duty cycle.
Cycle times are processor speed dependent and decreases linearly as processor core
frequencies increase. Once the temperature has returned to a non-critical level,
modulation ceases and TCC goes inactive. A small amount of hysteresis has been
included to prevent rapid active/inactive transitions of the TCC when the processor
temperature is near the trip point. The duty cycle is factory configured and cannot be
modified. Also, automatic mode does not require any additional hardware, software
drivers, or interrupt handling routines. Processor performance decreases by the same
amount as the duty cycle when the TCC is active.
When Intel Thermal Monitor 2 is enabled and a high temperature situation exists, the
processor performs an Enhanced Intel SpeedStep Technology transition to the LFM.
When the processor temperature drops below the critical level, the processor makes an
Enhanced Intel SpeedStep Technology transition to the last requested operating point.
The processor also supports Enhanced Multi Threaded Thermal Monitoring (EMTTM).
84
Datasheet
Thermal Specifications and Design Considerations
EMTTM is a processor feature that enhances Intel Thermal Monitor 2 with a processor
throttling algorithm known as Adaptive Intel Thermal Monitor 2. Adaptive Intel Thermal
Monitor 2 transitions to intermediate operating points, rather than directly to the LFM,
once the processor has reached its thermal limit and subsequently searches for the
highest possible operating point. Please ensure this feature is enabled and supported in
the BIOS. Also with EMTTM enabled, the operating system can request the processor to
throttling to any point between Intel Dynamic Acceleration Technology frequency and
SuperLFM frequency as long as these features are enabled in the BIOS and supported
by the processor. The Intel Thermal Monitor automatic mode and Enhanced Multi
Threaded Thermal Monitoring must be enabled through BIOS for the processor to be
operating within specifications.
Note:
Intel Thermal Monitor 1, Intel Thermal Monitor 2 and EMTTM features are collectively
referred to as Adaptive Thermal Monitoring features. Intel recommends Intel Thermal
Monitor 1 and 2 be enabled on the processors.
Intel Thermal Monitor 1 and 2 can co-exist within the processor. If both Intel Thermal
Monitor 1 and 2 bits are enabled in the auto-throttle MSR, Intel Thermal Monitor 2
takes precedence over Intel Thermal Monitor 1. However, if Force Intel Thermal Monitor
1 over Intel Thermal Monitor 2 is enabled in MSRs via BIOS and Intel Thermal Monitor
2 is not sufficient to cool the processor below the maximum operating temperature,
then Intel Thermal Monitor 1 also activates to help cool down the processor.
If a processor load based Enhanced Intel SpeedStep Technology transition (through
MSR write) is initiated when a Intel Thermal Monitor 2 period is active, there are two
possible results:
1. If the processor load based Enhanced Intel SpeedStep Technology transition target
frequency is higher than the Intel Thermal Monitor 2 transition-based target
frequency, the processor load-based transition deferrs until the Intel Thermal
Monitor 2 event has been completed.
2. If the processor load-based Enhanced Intel SpeedStep Technology transition target
frequency is lower than the Intel Thermal Monitor 2 transition-based target
frequency, the processor transitions to the processor load-based Enhanced Intel
SpeedStep Technology target frequency point.
The TCC may also be activated via on-demand mode. If bit 4 of the ACPI Intel Thermal
Monitor control register is written to a 1, the TCC activates immediately independent of
the processor temperature. When using on-demand mode to activate the TCC, the duty
cycle of the clock modulation is programmable via bits 3:1 of the same ACPI Intel
Thermal Monitor control register. In automatic mode, the duty cycle is fixed at 50% on,
50% off, however in on-demand mode, the duty cycle can be programmed from 12.5%
on/ 87.5% off, to 87.5% on/12.5% off in 12.5% increments. On-demand mode may be
used at the same time automatic mode is enabled, however, if the system tries to
enable the TCC via on-demand mode at the same time automatic mode is enabled and
a high temperature condition exists, automatic mode takes precedence.
An external signal, PROCHOT# (processor hot) is asserted when the processor detects
that its temperature is above the thermal trip point. Bus snooping and interrupt
latching are also active while the TCC is active.
Besides the thermal sensor and thermal control circuit, the Intel Thermal Monitor also
includes one ACPI register, one performance counter register, three MSR, and one I/O
pin (PROCHOT#). All are available to monitor and control the state of the Intel Thermal
Monitor feature. The Intel Thermal Monitor can be configured to generate an interrupt
upon the assertion or deassertion of PROCHOT#.
PROCHOT# is not be asserted when the processor is in the Stop Grant, Sleep, Deep
Sleep, and Deeper Sleep low power states, hence the thermal diode reading must be
used as a safeguard to maintain the processor junction temperature within maximum
specification. If the platform thermal solution is not able to maintain the processor
Datasheet
85
Thermal Specifications and Design Considerations
junction temperature within the maximum specification, the system must initiate an
orderly shutdown to prevent damage. If the processor enters one of the above low
power states with PROCHOT# already asserted, PROCHOT# will remain asserted until
the processor exits the low power state and the processor junction temperature drops
below the thermal trip point.
If Intel Thermal Monitor automatic mode is disabled, the processor will be operating out
of specification. Regardless of enabling the automatic or on-demand modes, in the
event of a catastrophic cooling failure, the processor will automatically shut down when
the silicon has reached a temperature of approximately 125°C. At this point the
THERMTRIP# signal will go active. THERMTRIP# activation is independent of processor
activity and does not generate any bus cycles. When THERMTRIP# is asserted, the
processor core voltage must be shut down within the time specified in Chapter 3.
In all cases the Intel Thermal Monitor feature must be enabled for the processor to
remain within specification.
5.1.4
Digital Thermal Sensor
The processor also contains an on die Digital Thermal Sensor (DTS) that can be read
via an MSR (no I/O interface). Each core of the processor will have a unique digital
thermal sensor whose temperature is accessible via the processor MSRs. The DTS is the
preferred method of reading the processor die temperature since it can be located
much closer to the hottest portions of the die and can thus more accurately track the
die temperature and potential activation of processor core clock modulation via the
Intel Thermal Monitor. The DTS is only valid while the processor is in the normal
operating state (the Normal package level low power state).
Unlike traditional thermal devices, the DTS will output a temperature relative to the
maximum supported operating temperature of the processor (TJ,max). It is the
responsibility of software to convert the relative temperature to an absolute
temperature. The temperature returned by the DTS will always be at or below TJ,max.
Catastrophic temperature conditions are detectable via an Out Of Spec status bit. This
bit is also part of the DTS MSR. When this bit is set, the processor is operating out of
specification and immediate shutdown of the system should occur. The processor
operation and code execution is not guaranteed once the activation of the Out of Spec
status bit is set.
The DTS-relative temperature readout corresponds to the Intel Thermal Monitor 1/Intel
Thermal Monitor 2 trigger point. When the DTS indicates maximum processor core
temperature has been reached, the Intel Thermal Monitor 1 or 2 hardware thermal
control mechanism will activate. The DTS and Intel Thermal Monitor 1/Intel Thermal
Monitor 2 temperature may not correspond to the thermal diode reading because the
thermal diode is located in a separate portion of the die and thermal gradient between
the individual core DTS. Additionally, the thermal gradient from DTS to thermal diode
can vary substantially due to changes in processor power, mechanical and thermal
attach, and software application. The system designer is required to use the DTS to
guarantee proper operation of the processor within its temperature operating
specifications.
Changes to the temperature can be detected via two programmable thresholds located
in the processor MSRs. These thresholds have the capability of generating interrupts
via the core's local APIC. Refer to the Intel® 64 and IA-32 Architectures Software
Developer’s Manual for specific register and programming details.
86
Datasheet
Thermal Specifications and Design Considerations
5.1.5
Out of Specification Detection
Overheat detection is performed by monitoring the processor temperature and
temperature gradient. This feature is intended for graceful shut down before the
THERMTRIP# is activated. If the processor’s Intel Thermal Monitor 1 or 2 are triggered
and the temperature remains high, an “Out Of Spec” status and sticky bit are latched in
the status MSR register and generates thermal interrupt.
5.1.6
PROCHOT# Signal Pin
An external signal, PROCHOT# (processor hot), is asserted when the processor die
temperature has reached its maximum operating temperature. If Intel Thermal Monitor
1 or 2 is enabled, then the TCC will be active when PROCHOT# is asserted. The
processor can be configured to generate an interrupt upon the assertion or deassertion
of PROCHOT#. Refer to the Intel® 64 and IA-32 Architectures Software Developer’s
Manual for specific register and programming details.
The processor implements a bi-directional PROCHOT# capability to allow system
designs to protect various components from overheating situations. The PROCHOT#
signal is bi-directional in that it can either signal when the processor has reached its
maximum operating temperature or be driven from an external source to activate the
TCC. The ability to activate the TCC via PROCHOT# can provide a means for thermal
protection of system components.
Only a single PROCHOT# pin exists at a package level of the processor. When either
core's thermal sensor trips, the PROCHOT# signal will be driven by the processor
package. If only Intel Thermal Monitor 1 is enabled, PROCHOT# will be asserted and
only the core that is above TCC temperature trip point will have its core clocks
modulated. If Intel Thermal Monitor 2 is enabled, then regardless of which core(s) are
above TCC temperature trip point, both cores will enter the lowest programmed Intel
Thermal Monitor 2 performance state. It is important to note that Intel recommends
both Intel Thermal Monitor 1 and 2 to be enabled.
When PROCHOT# is driven by an external agent, if only Intel Thermal Monitor 1 is
enabled on both cores, then both processor cores will have their core clocks modulated.
If Intel Thermal Monitor 2 is enabled on both cores, then both processor cores will
enter the lowest programmed Intel Thermal Monitor 2 performance state. It should be
noted that Force Intel Thermal Monitor 1 on Intel Thermal Monitor 2, enabled via BIOS,
does not have any effect on external PROCHOT#. If PROCHOT# is driven by an external
agent when Intel Thermal Monitor 1, Intel Thermal Monitor 2, and Force Intel Thermal
Monitor 1 on Intel Thermal Monitor 2 are all enabled, then the processor will still apply
only Intel Thermal Monitor 2.
PROCHOT# may be used for thermal protection of voltage regulators (VR). System
designers can create a circuit to monitor the VR temperature and activate the TCC
when the temperature limit of the VR is reached. By asserting PROCHOT# (pulled-low)
and activating the TCC, the VR will cool down as a result of reduced processor power
consumption. Bi-directional PROCHOT# can allow VR thermal designs to target
maximum sustained current instead of maximum current. Systems should still provide
proper cooling for the VR and rely on bi-directional PROCHOT# only as a backup in case
of system cooling failure. The system thermal design should allow the power delivery
circuitry to operate within its temperature specification even while the processor is
operating at its TDP. With a properly designed and characterized thermal solution, it is
anticipated that bi-directional PROCHOT# would only be asserted for very short periods
of time when running the most power intensive applications. An under-designed
thermal solution that is not able to prevent excessive assertion of PROCHOT# in the
anticipated ambient environment may cause a noticeable performance loss.
§
Datasheet
87