MICROSEMI SL05

SL03
thru
8700 E. Thomas Road
Scottsdale, AZ 85251
Tel: (480) 941-6300
Fax: (480) 947-1503
SL24
TVSarray
 Series
DESCRIPTION (300 watt)
This 3 pin ULTRA LOW CAPACITANCE TRANSIENT VOLTAGE
SUPPRESSOR is designed for use in applications where protection is
required at the board level from voltage transients caused by
electrostatic discharge (ESD) as defined by IEC 1000-4-2, electrical
fast transients (EFT) per IEC 1000-4-4.
This product provides unidirectional protection for 1 line by connecting
the Input/Output line to pin 1, pin 2 to common or ground and pin 3 (is
not connected). The SL03 thru SL24 product provides board level
protection from static electricity and other induced-voltage surges that
can damage sensitive circuitry.
These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays protect 3.0/3.3 Volt components such
as DRAM’s, SRAM’s, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24 Volts. Because of the
physical size, weight and protection capabilities, this product is ideal for use in but not limited to
miniaturized electronic equipment such as hand held instruments, computers, computer peripherals and
cell phones.
FEATURES
•
•
•
•
PACKAGING
•
•
Protects 3.0/3.3 up through 24V Components
Protects 1 Unidirectional line
Provides electrically isolated protection
SOT-23 Packaging
•
MECHANICAL
MAXIMUM RATINGS
•
•
•
•
Tape & Reel EIA Standard 481
7 inch reel 5,000 pieces
13 inch reel 10,000 pieces
•
•
•
Operating Temperatures: -55ºC to +150ºC
Storage Temperature: -55ºC to +150ºC
SL03 thru SL24 have a Peak Pulse Power: 300 Watts
(8/20 µsec, Figure 1)
Pulse Repetition Rate: <.01%
Molded SOT-23 Surface Mount
Weight: .014 grams (approximate)
Body Marked with device number
º
ELECTRICAL CHARACTERISTICS @ 25 C Unless otherwise specified
PART
NUMBER
DEVICE
MARKING
CAPACITANCE
@0V, 1 MHz
C
TEMPERATURE
COEFFICIENT
OF VBR
áVBR
VOLTS
CLAMPING
VOLTAGE
VC
@ 5 Amp
(FIGURE 2)
VOLTS
LEAKAGE
CURRENT
ID
@ VWM
VOLTS
CLAMPING
VOLTAGE
VC
@ 1 Amp
(FIGURE 2)
VOLTS
µA
pF
mV/ºC
MAX
MIN
MAX
MAX
MAX
MAX
MAX
-5
STAND
OFF
VOLTAGE
VWM
BREAKDOWN
VOLTAGE
VBR
@1 mA
SL03
L03
3.3
4
8
11
200
3
SL05
L05
5.0
6.0
10.8
13
100
3
3
SL12
L12
12.0
13.3
19
26
1
3
10
SL15
L15
15.0
16.7
25
32
1
3
13
SL24
L24
24.0
26.7
44
57
1
3
30
NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off Voltage VWM. Product
selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected.
MSC1377.PDF
ISO 9001 CERTIFIED
REV C 1/27/2000
SL03 thru SL24
100
Ipp -- Peak Pulse Current -- % Ipp
PPP - PEAK PULSE POWER
WAVE FORMS
8/20 µs 300 W pulse
10
1.0
.10
100ns
1µs
10µs
100µs
1ms
td – PULSE TIME - SEC
Peak Value -- Ipp
8 X 20 Waveform
50
Half-Value -- Ipp
2
0
0
10ms
10
20
30
t
td
t -- Time in microsec
FIGURE 1
Peak Pulse Power Vs Pulse Time
MOUNTING PAD SOT23
100
FIGURE 2
Pulse Wave Form
CIRCUIT DIAGRAM
PACKAGE OUTLINE
MSC1377.PDF
ISO 9001 CERTIFIED
REV C 1/27/2000