LINEAGEPOWER AXH016A0X3-SRZ

Data Sheet
August 12, 2008
Austin SuperLynxTM SMT Non-isolated Power Modules:
3.0Vdc – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A Output Current
RoHS Compliant
Applications
Features
ƒ
Compliant to RoHS EU Directive 2002/95/EC (Z versions)
ƒ
Compliant to ROHS EU Directive 2002/95/EC
with lead solder exemption (non-Z versions)
ƒ
Delivers up to 16A of output current
ƒ
High efficiency – 95% at 3.3V full load (VIN =
5.0V)
ƒ
Small size and low profile:
ƒ
33.00 mm x 13.46 mm x 8.28 mm
ƒ
(1.300 in x 0.530 in x 0.326 in)
ƒ
Low output ripple and noise
ƒ
High Reliability:
ƒ
Calculated MTBF > 6.8M hours at 25 C Fullload
ƒ
Output voltage programmable from 0.75 Vdc to
3.63Vdc via external resistor
o
ƒ
Distributed power architectures
ƒ
Intermediate bus voltage applications
ƒ
Telecommunications equipment
ƒ
Line Regulation: 0.3% (typical)
ƒ
Servers and storage applications
ƒ
Load Regulation: 0.4% (typical)
ƒ
Temperature Regulation: 0.4% (typical)
ƒ
Remote On/Off
ƒ
Remote Sense
ƒ
Output overcurrent protection (non-latching)
ƒ
Overtemperature protection
ƒ
Wide operating temperature range (-40°C to
85°C)
ƒ
UL* 60950-1Recognized, CSA C22.2 No.
60950-1-03 Certified, and VDE‡ 0805:2001-12
(EN60950-1) Licensed
ƒ
ISO** 9001 and ISO 14001 certified
manufacturing facilities
ƒ
Networking equipment
†
Description
Austin SuperLynxTM SMT (surface mount technology) power modules are non-isolated dc-dc converters that can
deliver up to 16A of output current with full load efficiency of 95% at 3.3V output. These modules provide a
precisely regulated output voltage programmable via external resistor from 0.75Vdc to 3.63Vdc over a wide range of
input voltage (VIN = 3.0 – 5.5Vdc). Their open-frame construction and small footprint enable designers to develop
cost- and space-efficient solutions. Standard features include remote On/Off, remote sense, programmable output
voltage, overcurrent and overtemperature protection.
* UL is a registered trademark of Underwriters Laboratories, Inc.
†
CSA is a registered trademark of Canadian Standards Association.
VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
‡
Document No: DS03-081 ver. 1.43
PDF name: superlynx_smt_3v-5.5v.pdf
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter
Device
Symbol
Min
Max
Unit
All
VIN
-0.3
5.8
Vdc
All
TA
-40
85
°C
All
Tstg
-55
125
°C
Input Voltage
Continuous
Operating Ambient Temperature
(see Thermal Considerations section)
Storage Temperature
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter
Device
Symbol
Min
Typ
Max
Unit
Operating Input Voltage
VO,set ≤ VIN – 0.5V
VIN
3.0
⎯
5.5
Vdc
Maximum Input Current
All
IIN,max
16.0
Adc
VO,set = 0.75 Vdc
IIN,No load
70
mA
VO,set = 3.3Vdc
IIN,No load
70
mA
All
IIN,stand-by
1.5
mA
Inrush Transient
All
It
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN, min to
VIN, max, IO= IOmax ; See Test configuration section)
All
100
Input Ripple Rejection (120Hz)
All
30
(VIN= VIN, min to VIN, max, IO=IO, max VO,set = 3.3Vdc)
Input No Load Current
(VIN = 5.0Vdc, IO = 0, module enabled)
Input Stand-by Current
(VIN = 5.0Vdc, module disabled)
2
0.1
2
As
mAp-p
dB
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to being
part of a complex power architecture. To preserve maximum flexibility, internal fusing is not included, however, to
achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a fastacting fuse with a maximum rating of 20A (see Safety Considerations section). Based on the information provided in
this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be
used. Refer to the fuse manufacturer’s data sheet for further information.
LINEAGE POWER
2
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Electrical Specifications (continued)
Parameter
Output Voltage Set-point
Device
Symbol
Min
Typ
Max
Unit
All
VO, set
–2.0
⎯
+2.0
% VO, set
All
VO, set
–3%
⎯
+3%
% VO, set
All
VO
0.7525
3.63
Vdc
(VIN=IN, min, IO=IO, max, TA=25°C)
Output Voltage
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Adjustment Range
Selected by an external resistor
Output Regulation
Line (VIN=VIN, min to VIN, max)
All
⎯
0.3
% VO, set
Load (IO=IO, min to IO, max)
All
⎯
0.4
% VO, set
Temperature (Tref=TA, min to TA, max)
All
⎯
0.4
% VO, set
RMS (5Hz to 20MHz bandwidth)
All
⎯
8
15
mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth)
All
⎯
25
50
mVpk-pk
μF
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max
Cout = 1μF ceramic//10μFtantalum capacitors)
External Capacitance
ESR ≥ 1 mΩ
All
CO, max
⎯
⎯
1000
ESR ≥ 10 mΩ
All
CO, max
⎯
⎯
3000
μF
Output Current
All
Io
0
⎯
16
Adc
Output Current Limit Inception (Hiccup Mode )
All
IO, lim
⎯
180
⎯
% Io
Output Short-Circuit Current
All
IO, s/c
⎯
3.5
⎯
Adc
(VO≤250mV) ( Hiccup Mode )
Efficiency
VIN= VIN, nom, TA=25°C
IO=IO, max , VO= VO,set
Switching Frequency
VO,set = 0.75Vdc
η
82.0
%
VO, set = 1.2Vdc
η
87.0
%
VO,set = 1.5Vdc
η
89.0
%
VO,set = 1.8Vdc
η
90.0
%
VO,set = 2.5Vdc
η
92.5
%
VO,set = 3.3Vdc
η
95.0
All
fsw
⎯
300
⎯
kHz
All
Vpk
⎯
300
⎯
mV
%
Dynamic Load Response
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C)
Load Change from Io= 50% to 100% of
Io,max; 1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation)
All
ts
⎯
25
⎯
μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C)
All
Vpk
⎯
300
⎯
mV
All
ts
⎯
25
⎯
μs
Load Change from Io= 100% to 50%of Io,max:
1μF ceramic// 10 μF tantalum
Peak Deviation
Settling Time (Vo<10% peak deviation)
LINEAGE POWER
3
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Electrical Specifications (continued)
Parameter
Device
Symbol
Min
Typ
Max
Unit
All
Vpk
⎯
150
⎯
mV
Dynamic Load Response
(dIo/dt=2.5A/μs; V VIN = VIN, nom; TA=25°C)
Load Change from Io= 50% to 100% of Io,max;
Co = 2x150 μF polymer capacitors
Peak Deviation
Settling Time (Vo<10% peak deviation)
All
ts
⎯
100
⎯
μs
(dIo/dt=2.5A/μs; VIN = VIN, nom; TA=25°C)
Load Change from Io= 100% to 50%of Io,max:
Co = 2x150 μF polymer capacitors
Peak Deviation
All
Vpk
⎯
150
⎯
mV
Settling Time (Vo<10% peak deviation)
All
ts
⎯
100
⎯
μs
General Specifications
Parameter
Min
Calculated MTBF (IO=IO, max, TA=25°C)
Weight
LINEAGE POWER
Typ
Max
6, 800,000
⎯
5.6 (0.2)
Unit
Hours
⎯
g (oz.)
4
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter
Device
Symbol
Min
Typ
Max
Unit
All
VIH
―
―
VIN, max
V
μA
Remote On/Off Signal interface
(VIN=VIN, min to VIN, max; Open collector pnp or equivalent
Compatible, Von/off signal referenced to GND
See feature description section)
Input High Voltage (Module ON)
Input High Current
All
IIH
―
―
10
Input Low Voltage (Module OFF)
All
VIL
-0.2
―
0.3
V
Input Low Current
All
IIL
―
0.2
1
mA
Case 1: On/Off input is set to Logic Low (Module
ON) and then input power is applied (delay from
instant at which VIN =VIN, min until Vo=10% of Vo,set)
All
Tdelay
3.9
msec
Case 2: Input power is applied for at least one second
and then the On/Off input is set to logic Low (delay from
instant at which Von/Off=0.3V until Vo=10% of Vo, set)
All
Tdelay
3.9
msec
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
All
Trise
Turn-On Delay and Rise Times
o
(IO=IO, max , VIN = VIN, nom, TA = 25 C, )
―
4.2
8,5
msec
―
1
% VO, set
⎯
125
⎯
°C
Output voltage overshoot – Startup
o
IO= IO, max; VIN = 3.0 to 5.5Vdc, TA = 25 C
Overtemperature Protection
All
Tref
(See Thermal Consideration section)
Input Undervoltage Lockout
Turn-on Threshold
All
⎯
2.2
⎯
V
Turn-off Threshold
All
⎯
2.0
⎯
V
LINEAGE POWER
5
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Characteristic Curves
The following figures provide typical characteristics for the Austin SuperLynxTM SMT modules at 25ºC.
96
90
93
87
EFFICIENCY, η (%)
EFFICIENCY, η (%)
90
84
81
VIN = 3.0V
78
VIN = 5.0V
75
VIN = 5.5V
72
87
84
81
VIN = 3.0V
78
VIN = 5.0V
75
VIN = 5.5V
72
0
4
8
12
16
0
4
OUTPUT CURRENT, IO (A)
8
12
16
OUTPUT CURRENT, IO (A)
Figure 1. Converter Efficiency versus Output Current
(Vout = 0.75Vdc).
Figure 4. Converter Efficiency versus Output Current
(Vout = 1.8Vdc).
93
100
97
90
87
EFFICIENCY, η (%)
EFFICIENCY, η (%)
94
84
81
VIN = 3.0V
78
VIN = 5.0V
75
VIN = 5.5V
72
91
88
85
82
VIN = 5.0V
76
VIN = 5.5V
73
0
4
8
12
16
0
OUTPUT CURRENT, IO (A)
97
88
94
EFFICIENCY, η (%)
100
91
85
82
79
VIN = 3.0V
VIN = 5.0V
73
8
12
16
Figure 5. Converter Efficiency versus Output Current
(Vout = 2.5Vdc).
94
76
4
OUTPUT CURRENT, IO (A)
Figure 2. Converter Efficiency versus Output Current
(Vout = 1.2Vdc).
EFFICIENCY, η (%)
VIN = 3.0V
79
VIN = 5.5V
70
91
88
85
VIN = 4.5V
82
VIN = 5.0V
79
VIN = 5.5V
76
0
4
8
12
16
OUTPUT CURRENT, IO (A)
Figure3. Converter Efficiency versus Output Current
(Vout = 1.5Vdc).
LINEAGE POWER
0
4
8
12
16
OUTPUT CURRENT, IO (A)
Figure 6. Converter Efficiency versus Output Current
(Vout = 3.3Vdc).
6
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Characteristic Curves (continued)
INPUT CURRENT, IIN (A)
Io =8A
14
Io =16A
12
10
8
6
4
2
0
0.5
1.5
2.5
3.5
TIME, t (5 μs/div)
TIME, t (2μs/div)
Figure 9. Typical Output Ripple and Noise
(Vin = 5.0V dc, Vo = 3.3 Vdc, Io=16A).
LINEAGE POWER
IO (A) (5A/div)
TIME, t (5 μs/div)
VO (V) (200mV/div)
Figure 11. Transient Response to Dynamic Load
Change from 100% to 50% of full load (Vo = 3.3 Vdc).
IO (A) (5A/div)
VO (V) (20mV/div)
OUTPUT VOLTAGE
Figure 8. Typical Output Ripple and Noise
(Vin = 5.0V dc, Vo = 0.75 Vdc, Io=16A).
OUTPUT CURRENT, OUTPUT VOLTAGE
TIME, t (2μs/div)
VO (V) (200mV/div)
Figure 10. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 3.3Vdc).
VO (V) (20mV/div)
Figure 7. Input voltage vs. Input Current
(Vout = 2.5Vdc).
OUTPUT CURRENT, OUTPUT VOLTAGE
5.5
OUTPUT VOLTAGE
INPUT VOLTAGE, VIN (V)
4.5
VO (V) (200mV/div)
Io =0A
16
IO (A) (5A/div)
18
OUTPUT CURRENT, OUTPUT VOLTAGE
The following figures provide typical characteristics for the Austin SuperLynxTM SMT modules at 25ºC.
TIME, t (10μs/div)
Figure 12. Transient Response to Dynamic Load
Change from 50% to 100% of full load (Vo = 5.0 Vdc,
Cext = 2x150 μF Polymer Capacitors).
7
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Characteristic Curves (continued)
VOV) (1V/div)
INPUT VOLTAGE
VNN (V) (2V/div)
OUTPUT VOLTAGE
VOV) (1V/div)
VOn/off (V) (2V/div)
TIME, t (2 ms/div)
Figure 17 Typical Start-Up Using Remote On/Off with
Prebias (Vin = 3.3Vdc, Vo = 1.8Vdc, Io = 1.0A, Vbias
=1.0Vdc).
OUTPUT CURRENT,
On/Off VOLTAGE
VOn/off (V) (2V/div)
OUTPUT VOLTAGE
TIME, t (2 ms/div)
Figure 15. Typical Start-Up Using Remote On/Off with
Low-ESR external capacitors (Vin = 5.5Vdc, Vo =
3.3Vdc, Io = 16.0A, Co = 1050μF).
LINEAGE POWER
On/Off VOLTAGE
VOn/off (V) (2V/div)
VOV) (1V/div)
TIME, t (2 ms/div)
Figure 14. Typical Start-Up Using Remote On/Off (Vin
= 5.0Vdc, Vo = 3.3Vdc, Io = 16.0A).
Figure 16. Typical Start-Up with application of Vin
(Vin = 5.0Vdc, Vo = 3.3Vdc, Io = 16A).
VOV) (1V/div)
On/Off VOLTAGE
OUTPUT VOLTAGE
Figure 13. Transient Response to Dynamic Load
Change from 100% of 50% full load (Vo = 5.0 Vdc, Cext
= 2x150 μF Polymer Capacitors).
TIME, t (2 ms/div)
OUTPUT VOLTAGE
TIME, t (10μs/div)
IO (A) (10A/div)
OUTPUT CURRENT, OUTPUTVOLTAGE
IO (A) (5A/div)
VO (V) (200mV/div)
The following figures provide typical characteristics for the Austin SuperLynxTM SMT modules at 25ºC.
TIME, t (10ms/div)
Figure 18. Output short circuit Current (Vin = 5.0Vdc,
Vo = 0.75Vdc).
8
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Characteristic Curves (continued)
18
18
16
16
14
12
10
NC
8
100 LFM
6
200 LFM
4
300 LFM
2
400 LFM
0
20
30
40
50
60
70
80
90
O
OUTPUT CURRENT, Io (A)
OUTPUT CURRENT, Io (A)
The following figures provide thermal derating curves for the Austin SuperLynxTM SMT modules.
14
12
10
NC
8
6
100 LFM
200 LFM
4
300 LFM
2
400 LFM
0
20
30
40
50
60
70
80
90
O
AMBIENT TEMPERATURE, TA C
AMBIENT TEMPERATURE, TA C
Figure 19. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 5.0,
Vo=3.3Vdc).
Figure 22. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 3.3dc,
Vo=0.75 Vdc).
18
OUTPUT CURRENT, Io (A)
16
14
12
10
NC
8
6
100 LFM
200 LFM
4
300 LFM
2
400 LFM
0
20
30
40
50
60
70
80
90
O
AMBIENT TEMPERATURE, TA C
Figure 20. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 5.0Vdc,
Vo=0.75 Vdc).
18
OUTPUT CURRENT, Io (A)
16
14
12
10
NC
8
6
4
100 LFM
200 LFM
300 LFM
2
400 LFM
0
20
30
40
50
60
70
80
90
O
AMBIENT TEMPERATURE, TA C
Figure 21. Derating Output Current versus Local
Ambient Temperature and Airflow (Vin = 3.3Vdc,
Vo=2.5 Vdc).
LINEAGE POWER
9
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Test Configurations
Design Considerations
CURRENT PROBE
TO OSCILLOSCOPE
VIN(+)
BATTERY
CIN
CS 1000μF
Electrolytic
2x100μF
Tantalum
E.S.R.<0.1Ω
@ 20°C 100kHz
COM
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
Figure 23. Input Reflected Ripple Current Test Setup.
COPPER STRIP
To minimize input voltage ripple, low-ESR polymer and
ceramic capacitors are recommended at the input of the
module. Figure 26 shows the input ripple voltage (mVpp) for various outputs with 1x150 µF polymer capacitors
(Panasonic p/n: EEFUE0J151R, Sanyo p/n: 6TPE150M)
in parallel with 1 x 47 µF ceramic capacitor (Panasonic
p/n: ECJ-5YB0J476M, Taiyo- Yuden p/n:
CEJMK432BJ476MMT) at full load. Figure 27 shows the
input ripple with 2x150 µF polymer capacitors in parallel
with 2 x 47 µF ceramic capacitor at full load.
RESISTIVE
LOAD
1uF
.
10uF
400
SCOPE
COM
GROUND PLANE
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 24. Output Ripple and Noise Test Setup.
Rdistribution
Rcontact
Rcontact
VIN(+)
Rdistribution
VO
RLOAD
VO
VIN
Input Ripple Voltage (mVp-p)
VO (+)
TM
The Austin SuperLynx SMT module should be
connected to a low-impedance source. A highly inductive
source can affect the stability of the module. An input
capacitance must be placed directly adjacent to the input
pin of the module, to minimize input ripple voltage and
ensure module stability.
LTEST
1μH
Input Filtering
350
300
250
200
150
3.3Vin
100
5Vin
50
0
0
0.5
1
1.5
2
2.5
3
3.5
Output Voltage (Vdc)
Figure 26. Input ripple voltage for various output
with 1x150 µF polymer and 1x47 µF ceramic
capacitors at the input (full load).
Rcontact
Rcontact
COM
Rdistribution
COM
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 25. Output Voltage and Efficiency Test Setup.
VO. IO
Efficiency
η =
VIN. IIN
x
100 %
Input Ripple Voltage (mVp-p)
250
Rdistribution
200
150
100
3.3Vin
50
5Vin
0
0
0.5
1
1.5
2
2.5
3
3.5
Output Voltage (Vdc)
Figure 27. Input ripple voltage for various output
with 2x150 µF polymer and 2x47 µF ceramic
capacitors at the input (full load).
LINEAGE POWER
10
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Design Considerations (continued)
Safety Considerations
Output Filtering
For safety agency approval the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standards,
i.e., UL 60950-1, CSA C22.2 No. 60950-1-03, and VDE
0850:2001-12 (EN60950-1) Licensed.
TM
The Austin SuperLynx SMT module is designed for low
output ripple voltage and will meet the maximum output
ripple specification with 1 µF ceramic and 10 µF tantalum
capacitors at the output of the module. However,
additional output filtering may be required by the system
designer for a number of reasons. First, there may be a
need to further reduce the output ripple and noise of the
module. Second, the dynamic response characteristics
may need to be customized to a particular load step
change.
To reduce the output ripple and improve the dynamic
response to a step load change, additional capacitance at
the output can be used. Low ESR polymer and ceramic
capacitors are recommended to improve the dynamic
response of the module. For stable operation of the
module, limit the capacitance to less than the maximum
output capacitance as specified in the electrical
specification table.
LINEAGE POWER
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements. The power module
has extra-low voltage (ELV) outputs when all inputs are
ELV.
The input to these units is to be provided with a fastacting fuse with a maximum rating of 20A in the positive
input lead.
11
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
the unit will survive temperatures beyond its rating. The
module will automatically restart after it cools down.
Feature Description
Remote On/Off
Output Voltage Programming
TM
The Austin SuperLynx SMT power modules feature an
On/Off pin for remote On/Off operation of the module.
The circuit configuration for using the On/Off pin is shown
in Figure 28. The On/Off pin is an open collector/drain
logic input signal (Von/Off) that is referenced to ground.
During a logic-high (On/Off pin is pulled high internal to
the module) when the transistor Q1 is in the Off state, the
power module is ON. Maximum allowable leakage
current of the transistor when Von/off = VIN,max is 10µA.
Applying a logic-low when the transistor Q1 is turned-On,
the power module is OFF. During this state VOn/Off
must be less than 0.3V. When not using positive logic
On/off pin, leave the pin unconnected or tie to VIN.
MODULE
VIN+
R2
ON/OFF
+
I ON/OFF
VON/OFF
TM
The output voltage of the Austin SuperLynx SMT can
be programmed to any voltage from 0.75 Vdc to 3.63
Vdc by connecting a single resistor (shown as Rtrim in
Figure 29) between the TRIM and GND pins of the
module. Without an external resistor between TRIM pin
and the ground, the output voltage of the module is
0.7525 Vdc. To calculate the value of the resistor Rtrim
for a particular output voltage Vo, use the following
equation:
⎡ 21070
⎤
Rtrim = ⎢
− 5110⎥ Ω
⎣Vo − 0.7525
⎦
For example, to program the output voltage of the Austin
SuperLynxTM module to 1.8 Vdc, Rtrim is calculated is
follows:
⎤
⎡ 21070
Rtrim = ⎢
− 5110⎥
⎦
⎣1.8 − 0.7525
Q2
R1
Rtrim = 15.004 kΩ
PWM Enable
R3
Q1
Q3
CSS
V IN(+)
V O(+)
Vout
R4
GND
_
ON/OFF
LOAD
TRIM
Figure 28. Remote On/Off Implementation.
R trim
GND
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally once
the output current is brought back into its specified range.
The typical average output current during hiccup is 3.5A.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, module operation is disabled. The module will begin
to operate at an input voltage above the undervoltage
lockout turn-on threshold.
Overtemperature Protection
To provide over temperature protection in a fault
condition, the unit relies upon the thermal protection
feature of the controller IC. The unit will shutdown if the
thermal reference point Tref, exceeds 125oC (typical), but
the thermal shutdown is not intended as a guarantee that
LINEAGE POWER
Figure 29. Circuit configuration for programming
output voltage using an external resistor.
TM
The Austin SuperLynx can also be programmed by
applying a voltage between the TRIM and the GND pins
(Figure 30). The following equation can be used to
determine the value of Vtrim needed to obtain a desired
output voltage Vo:
Vtrim = (0.7 − 0.1698 × {Vo − 0.7525})
For example, to program the output voltage of a
TM
SuperLynx module to 3.3 Vdc, Vtrim is calculated as
follows:
Vtrim = (0.7 − 0.1698 × {3.3 − 0.7525})
Vtrim = 0.2670V
12
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
The amount of power delivered by the module is defined
as the voltage at the output terminals multiplied by the
output current. When using the trim feature, the output
voltage of the module can be increased, which at the
same output current would increase the power output of
the module. Care should be taken to ensure that the
maximum output power of the module remains at or
below the maximum rated power (Pmax = Vo,set x Io,max).
Feature Descriptions (continued)
V IN(+)
V O(+)
ON/OFF
LOAD
TRIM
Voltage Margining
+
-
GND
Vtrim
Figure 30. Circuit Configuration for programming
Output voltage using external voltage source.
Table 1 provides Rtrim values required for some common
output voltages, while Table 2 provides values of the
external voltage source, Vtrim for the same common
output voltages.
Table 1
Output voltage margining can be implemented in the
Austin SuperLynxTM modules by connecting a resistor,
Rmargin-up, from the Trim pin to the ground pin for
margining-up the output voltage and by connecting a
resistor, Rmargin-down, from the Trim pin to the Output pin
for margining-down. Figure 31 shows the circuit
configuration for output voltage margining. The POL
Programming Tool, available at www.lineagepower.com
under the Design Tools section, also calculates the
values of Rmargin-up and Rmargin-down for a specific output
voltage and % margin. Please consult your local Lineage
Power technical representative for additional details.
Vo
VO, set (V)
Rtrim (KΩ)
0.7525
Open
1.2
41.973
1.5
23.077
1.8
15.004
2.5
6.947
3.3
3.160
Rmargin-down
Austin Lynx or
Lynx II Series
Q2
Trim
Rmargin-up
Rtrim
Table 2
VO, set (V)
Vtrim (V)
0.7525
Open
1.2
0.6240
1.5
0.5731
1.8
0.5221
2.5
0.4033
3.3
0.2674
Q1
GND
Figure 31. Circuit Configuration for margining Output
voltage.
By using a 1% tolerance trim resistor, set point tolerance
of ±2% is achieved as specified in the electrical
specification. The POL Programming Tool, available at
www.lineagepower.com under the Design Tools section,
helps determine the required external trim resistor
needed for a specific output voltage.
LINEAGE POWER
13
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Feature Descriptions (continued)
Remote Sense
TM
The Austin SuperLynx SMT power modules have a
Remote Sense feature to minimize the effects of
distribution losses by regulating the voltage at the
Remote Sense pin (See Figure 32). The voltage between
the Sense pin and Vo pin must not exceed 0.5V.
The amount of power delivered by the module is defined
as the output voltage multiplied by the output current (Vo
x Io). When using Remote Sense, the output voltage of
the module can increase, which if the same output is
maintained, increases the power output by the module.
Make sure that the maximum output power of the module
remains at or below the maximum rated power. When
the Remote Sense feature is not being used, connect the
Remote Sense pin to the output pin.
R d istrib u tio n
R co n ta c t
R c o nta ct
V IN (+ )
R d istrib utio n
VO
S e n se
R LO A D
R d istrib u tio n
R co n ta c t
R c o nta ct
COM
R d istrib utio n
COM
Figure 32. Remote sense circuit configuration
LINEAGE POWER
14
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Thermal Considerations
Power modules operate in a variety of thermal
environments; however, sufficient cooling should always
be provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of the
module will result in an increase in reliability. The thermal
data presented here is based on physical measurements
taken in a wind tunnel. The test set-up is shown in Figure
34. Note that the airflow is parallel to the short axis of the
module as shown in figure 33. The derating data applies
to airflow in either direction of the module’s short axis.
Mounted Power Modules” for a detailed discussion of
thermal aspects including maximum device temperatures.
25.4_
(1.0)
Wind Tunnel
PWBs
Power Module
Top View
76.2_
(3.0)
x
5.97_
(0.235)
Tref
Bottom View
Probe Location
for measuring
airflow and
ambient
temperature
Air
flow
Figure 34. Thermal Test Set-up.
Heat Transfer via Convection
Air Flow
Figure 33. Tref Temperature measurement location.
The thermal reference point, Tref used in the
specifications is shown in Figure 33. For reliable
operation this temperature should not exceed 115oC.
The output power of the module should not exceed the
rated power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal
Characterization Process For Open-Frame Board-
LINEAGE POWER
Increased airflow over the module enhances the heat
transfer via convection. Thermal derating curves showing
the maximum output current that can be delivered at
different local ambient temperatures (TA) for airflow
conditions ranging from natural convection and up to
2m/s (400 ft./min) are shown in the Characteristics
Curves section.
Layout Considerations
Copper paths must not be routed beneath the power
module. For additional layout guide-lines, refer to the
FLTR100V10 application note.
15
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
LINEAGE POWER
16
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
LINEAGE POWER
17
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Packaging Details
The Austin SuperLynxTM SMT version is supplied in tape & reel as standard. Modules are shipped in quantities of
250 modules per reel.
All Dimensions are in millimeters and (in inches).
Reel Dimensions:
Outside Dimensions:
Inside Dimensions:
Tape Width:
LINEAGE POWER
330.2 mm (13.00)
177.8 mm (7.00”)
44.00 mm (1.732”)
18
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Surface Mount Information
Pick and Place
Reflow Soldering Information
TM
The Austin SuperLynx SMT modules use an open
frame construction and are designed for a fully
automated assembly process. The modules are fitted
with a label designed to provide a large surface area
for pick and place operations. The label meets all the
requirements for surface mount processing, as well as
safety standards, and is able to withstand reflow
o
temperatures of up to 300 C. The label also carries
product information such as product code, serial
number and the location of manufacture.
TM
The Austin SuperLynx SMT power modules are
large mass, low thermal resistance devices and
typically heat up slower than other SMT components.
It is recommended that the customer review data
sheets in order to customize the solder reflow profile
for each application board assembly. The following
instructions must be observed when soldering these
units. Failure to observe these instructions may result
in the failure of or cause damage to the modules, and
can adversely affect long-term reliability.
o
Typically, the eutectic solder melts at 183 C, wets the
land, and subsequently wicks the device connection.
Sufficient time must be allowed to fuse the plating on
the connection to ensure a reliable solder joint. There
are several types of SMT reflow technologies
currently used in the industry. These surface mount
power modules can be reliably soldered using natural
forced convection, IR (radiant infrared), or a
combination of convection/IR. For reliable soldering
the solder reflow profile should be established by
accurately measuring the modules pin temperatures.
Figure 35. Pick and Place Location.
Nozzle Recommendations
The module weight has been kept to a minimum by
using open frame construction. Even so, these
modules have a relatively large mass when compared
to conventional SMT components. Variables such as
nozzle size, tip style, vacuum pressure and placement
speed should be considered to optimize this process.
The minimum recommended nozzle diameter for
reliable operation is 6mm. The maximum nozzle outer
diameter, which will safely fit within the allowable
component spacing, is 9 mm.
Oblong or oval nozzles up to 11 x 9 mm may also be
used within the space available.
LINEAGE POWER
Figure 36. Reflow Profile.
An example of a reflow profile (using 63/37 solder) for
the Austin SuperLynxTM SMT power module is :
•
Pre-heating zone: room temperature to 183oC
(2.0 to 4.0 minutes maximum)
•
Initial ramp rate < 2.5oC per second
o
o
•
Soaking Zone: 155 C to 183 C – 60 to 90
seconds typical (2.0 minutes maximum)
o
o
•
Reflow zone ramp rate:1.3 C to 1.6 C per second
o
o
•
Reflow zone: 210 C to 235 C peak temperature –
30 to 60 seconds (90 seconds maximum
19
Data Sheet
August 12, 2008
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Surface Mount Information (continued)
Lead Free Soldering
The –Z version Austin SuperLynx SMT modules are
lead-free (Pb-free) and RoHS compliant and are both
forward and backward compatible in a Pb-free and a
SnPb soldering process. Failure to observe the
instructions below may result in the failure of or cause
damage to the modules and can adversely affect
long-term reliability.
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. C
(Moisture/Reflow Sensitivity Classification for
Nonhermetic Solid State Surface Mount Devices)
for both Pb-free solder profiles and MSL
classification procedures. This standard provides a
recommended forced-air-convection reflow profile
based on the volume and thickness of the package
(table 4-2). The suggested Pb-free solder paste is
Sn/Ag/Cu (SAC). The recommended linear reflow
profile using Sn/Ag/Cu solder is shown in Fig. 37.
sealed packages should not be broken until time of
use. Once the original package is broken, the floor
life of the product at conditions of ≤ 30°C and 60%
relative humidity varies according to the MSL rating
(see J-STD-033A). The shelf life for dry packed
SMT packages will be a minimum of 12 months
from the bag seal date, when stored at the
following conditions: < 40° C, < 90% relative
humidity.
Post Solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect
both the reliability of a power module and the
testability of the finished circuit-board assembly. For
guidance on appropriate soldering, cleaning and
drying procedures, refer to Board Mounted Power
Modules: Soldering and Cleaning Application Note
(AN04-001).
300
Per J-STD-020 Rev. C
Peak Temp 260°C
250
The Austin SuperLynx SMT modules have a MSL
rating of 1.
Storage and Handling
The recommended storage environment and
handling procedures for moisture-sensitive surface
mount packages is detailed in J-STD-033 Rev. A
(Handling, Packing, Shipping and Use of
Moisture/Reflow Sensitive Surface Mount Devices).
Moisture barrier bags (MBB) with desiccant are
required for MSL ratings of 2 or greater. These
LINEAGE POWER
Reflow Temp (°C)
MSL Rating
200
150
* Min. Time Above 235°C
15 Seconds
Heating Zone
1°C/Second
Cooling
Zone
*Time Above 217°C
60 Seconds
100
50
0
Reflow Time (Seconds)
Figure 37. Recommended linear reflow profile
using Sn/Ag/Cu solder.
20
Austin SuperlynxTM SMT Non-isolated Power Modules:
3.0 – 5.5Vdc input; 0.75Vdc to 3.63Vdc Output; 16A output current
Data Sheet
August 12, 2008
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 3. Device Codes
Product codes
Input
Voltage
Output
Voltage
Output
Current
Efficiency
3.3V @ 16A
Connector
Type
Comcodes
AXH016A0X3-SR
3.0 – 5.5Vdc
0.75 – 3.63Vdc
16A
95.0%
SMT
108979519
AXH016A0X3-SRZ
3.0 – 5.5Vdc
0.75 – 3.63Vdc
16A
95.0%
SMT
108995180
AXH016A0X3-SR12*
3.0 – 5.5Vdc
0.75 – 3.63Vdc
16A
95.0%
SMT
108993416
AXH016A0X3-SR12Z*
3.0 – 5.5Vdc
0.75 – 3.63Vdc
16A
95.0%
SMT
CC109104477
* -12 code has 100Ω resistor between sense and output pins, internal to the module.
Standard code, without –12 suffix, has 10Ω resistor between sense and output pins.
-Z refers to RoHS-compliant parts
Asia-Pacific Headquarters
Tel: +65 6416 4283
World Wide Headquarters
Lineage Power Corporation
3000 Skyline Drive, Mesquite, TX 75149, USA
+1-800-526-7819
(Outside U.S.A.: +1-972-284-2626)
www.lineagepower.com
e-mail: [email protected]
Europe, Middle-East and Africa Headquarters
Tel: +49 89 6089 286
India Headquarters
Tel: +91 80 28411633
Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or
application. No rights under any patent accompany the sale of any such product(s) or information.
© 2008 Lineage Power Corporation, (Mesquite, Texas) All International Rights Reserved.
LINEAGE POWER
21
Document No: DS03-081 ver. 1.43
PDF name: superlynx_smt_3v-5.5v.pdf