PLN-45 45W Single Output LED Power Supply series Features : Universal AC input / Full range Fully isolated plastic case with IP64 level Built-in constant current limiting circuit with adjustable OCP level Protections: Short circuit / Overload / Over voltage / Over temperature Built-in active PFC function IP64 design for indoor or outdoor installations UL1310 Class 2 power unit Cooling by free air convection 100% full load burn-in test High reliability Suitable for LED lighting and moving sign applications Compliance to worldwide safety regulations for lighting 2 years warranty 110 F M EQUIVALENT MODEL DC VOLTAGE LPS ( for 48V only) ( except for 48V ) IP64 PLN-45-12 PLN-45-15 PLN-45-20 PLN-45-24 PLN-45-27 PLN-45-36 PLN-45-48 12V 15V 20V 24V 27V 36V 48V 10.5 ~15V 14 ~ 20V 16.8 ~24V 18.9 ~27V 25.2 ~ 36V 33.6 ~ 48V CONSTANT CURRENT 8.4 ~ 12V OPERATION VOLTAGE Note.7 OUTPUT SELV M SPECIFICATION RATED CURRENT 3.8A 3A 2.3A 1.9A 1.7A 1.25A 0.95A CURRENT RANGE 0 ~ 3.8A 0 ~ 3A 0 ~ 2.3A 0 ~ 1.9A 0 ~ 1.7A 0 ~ 1.25A 0 ~ 0.95A RATED POWER 45.6W RIPPLE & NOISE (max.) Note.2 2Vp-p VOLTAGE ADJ. RANGE Note.6 11.5 ~ 13V 45W 46W 45.6W 45.9W 45W 45.6W 2.4Vp-p 1.8Vp-p 2.7Vp-p 2.7Vp-p 3.6Vp-p 4.6Vp-p 14.5 ~ 16.2V 19.5 ~ 22V 24 ~ 26V 25 ~ 30V 32.5 ~ 39V 43.6 ~ 51.8V 86.5% 87.5% 87.5% Can be adjusted by internal potential meter SVR1 CURRENT ADJ. RANGE Note.6 3% ~ -25%. Can be adjusted by internal potential meter SVR2 VOLTAGE TOLERANCE Note.3 10% LINE REGULATION 3.0% 5.0% LOAD REGULATION 1500ms / 230VAC 3000ms / 115VAC at full load SETUP TIME Note.5 90 ~ 264VAC VOLTAGE RANGE INPUT 127 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR PF 0.9 at 75 ~ 100% load, 115VAC / 230VAC EFFICIENCY(Typ.) 83.5% 85% AC CURRENT INRUSH CURRENT(max.) 0.55A/115VAC 40A/230VAC 0.22A/230VAC 110% (max) 95 ~ 110% OVER CURRENT PROTECTION OVER VOLTAGE 86.5% <0.75mA / 240VAC LEAKAGE CURRENT SHORT CIRCUIT 86.5% Protection type : Constant current limiting, recovers automatically after fault condition is removed Note.4 Hiccup mode, recovers automatically after fault condition is removed. 13.8 ~ 16V 17.5 ~ 21V 22.8 ~ 25V 28 ~ 32V OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 31 ~ 35V 41 ~ 46V 54 ~ 60V Protection type : Shut down o/p voltage, re-power on to recover 95 10 (TSW1) detect on heatsink of power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ +50 (Refer to output load derating curve) 20 ~ 95% RH non-condensing -40 ~ +80 0.03%/ , 10 ~ 95% RH (0 ~ 50 ) 10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL1310 Class 2, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except for 48V), IP64 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC EMS IMMUNITY MTBF Compliance to EN61000-4-2,3,4,5,6,8,11; En61547, light industry level, criteria A I/P-FG:1.88KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH EMC EMI CONDUCTION & RADIATION Compliance to EN55015 Compliance to EN61000-3-2 Class C ( 75% load) ; EN61000-3-3 HARMONIC CURRENT OTHERS DIMENSION PACKING NOTE 497.8Khrs min. MIL-HDBK-217F (25 181*61.5*35mm (L*W*H) 0.5Kg; 24pcs/13Kg/0.75CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Direct connecting to LEDs is not suggested for models with RIPPLE & NOISE > 10% and using additional drivers is highly recommended. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Please refer to OLP characteristics. 5. Derating may be needed under low input voltage. Please check the derating curve for more details. 6. Output voltage can be adjusted through the SVR1 on the PCB ; limit of output constant current level can be adjusted through the SVR2 on the PCB. 7. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. File Name:PLN-45-SPEC 2009-10-01 PLN-45 45W Single Output LED Power Supply Mechanical Specification Case No.960A series Unit:mm 181 21.25 6.26 +V(Red) -V(Black) DC OUT 61.5 AC/L(Brown) AC/N(Blue) FG (Green/Yellow) 300 2-R2.5 300 18AWG 2C 21.25 AC IN 18AWG 3C 35 6.26 Output voltage and current adjustment : remove the upper case and adjust through SVR1 & SVR2 shown in the diagram. SVR1 SVR2 SVR1 Output voltage adjustment SVR2 Output current adjustment Block Diagram fosc : 95KHz(115VAC) 135KHz(230VAC) EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING FG +V -V DETECTION CIRCUIT O.L.P. PWM & PFC CONTROL O.C.P. O.V.P. Derating Curve Static Characteristics Ta:25 100 100 90 80 80 70 50 LOAD (%) LOAD (%) 60 40 20 -30 -25 -5 0 15 30 40 AMBIENT TEMPERATURE ( ) 50 60 (HORIZONTAL) 60 50 40 90 100 125 135 145 155 165 175 180 200 230 264 INPUT VOLTAGE (V) 60Hz File Name:PLN-45-SPEC 2009-10-01