ACTIVE SIGNAL AMPLIFIER Iin &Iout T11/12/21/22_D/S DESCRIPTION PRODUCT PROGRAM The series is a high integration, high efficiency polygonal - line active isolation Part Number amplifier module, with anterior circuit current T1133D/S 24V 4-20mA 4-20mA 24V 1 T1130D/S 24V 4-20mA 4-20mA NONE 1 efficiency isolated micro-power source, which T1230D/S 24V 4-20mA 0-20mA NONE 1 can provide a electrics-feed for signal input. In T2133D/S 24V 0-20mA 4-20mA 24V 1 the two-wire three-wire and four-wire circuit T2233D/S 24V 0-20mA 0-20mA 24V 1 T2230D/S 24V 0-20mA 0-20mA NONE 1 signal input and posterior current signal output. These modules are embed with a high applications, our products largely predigest customers’ design helpfully improve the using Power Supply Input Output Isolation Channels Power Output Note: We could also offer customer design for special input and output. room ratio of PCB. Adopting electromagnetism isolation technology, it is available to keep high accuracy and natural extrem ely low ELECTRICAL CHARACTERISTICS temperature drift. The isolation voltage among the input, output, power supply and isolated Power Supply Data power output can up to 2.5KVDC. Isolation Power Output Data FEATURES ● Four-port isolation（Among input, output, Input Data power supply and Isolation Power output） ● High accuracy (0.1% F.S.) ● High linearity (0.1% F.S.) Output Data ● Isolation voltage(2500VDC/60S) Power Supply (Nominal Power Supply) ±5% Power consumption ≤2W Power Protection Reverse protection Output Voltage (Nominal) ±10% Output Current ≤25mA Input Signal See above Input Impedance Voltage Drop≤250mV(At input=20mA) Overload ≤300mA Output Signal See above Load ≤500Ω（At output=20mA） ● High frequency response(15KHz) ● Extremely low temperature(35PPM/°C) TRANSMISSION CHARACTERISTICS ● Industry standard(Operating Temperature Offset Range:-25°C to 71°C) ● High reliability(MTBF＞500,000 hours) 0.1%F.S. Gain Error 0.1%F.S. Temperature Drift 0.0035%F.S./℃ (-25°C to +71 °C) ISOLATION CHARACTERISTICS MODEL SELECTION TXXXXD Package style Isolation power output Power supply Output Input Isolation Amplifier Galvanic Isolation Four-port isolation （ Among input, output, power supply and Isolation Power output） Isolation Voltage 2.5KVDC (Tested for 1minute and 1mA max, humidity < 70%) Insulation Resistance 1000MΩ, 500VDC(Among signal input, signal output, power supply and isolation power output) OTHER CHARACTERISTICS Ambient temperature Operation temperature:-25℃ to +71℃ Package DIP24/SOIC24 MORNSUN Science & Technology co.,Ltd. Weight About 10g Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com The Environment in use No dusts, gases of fiercely vibration, impulsion or gases that may erode to the components surrounded Transport and Storage temperature:-50℃ to +105℃ Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. Only typical models listed, specifications of custom product may be different. Please contact our service people directly for certain conditions. The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T11/12/21/22_D/S A/2-2008 Page 1 of 2 SCHEMATIC DIAGRAM APPLICATION NOTE 24Power supply 23+ 1. Please read instruction book carefully before using the product. If you have any question, please contact with our technical support. 13- 2. Please don’t install in the dangerous zone. Isolation Power Output 14+ 3. The power supply is direct voltage. 220V alternating current is forbidden.. Iout+ Iin12Signal i nput 11+ Ii n+ 2+ Si gnal output Iout- 4. Don’t divide the product privately in case the equipments ineffective or go wrong. 1- AFTER SERVICE 1. Products are carefully inspected and controlled APPLICATION CIRCUIT DIAGRAM before going out from our factory. If they operated abnorm ally or there were something Power Supply Isolation Power Out put wrong in the inner parts, please contact with our 16 15 14 13 PinPin+ NC NC NC NC NC PoutPou t+ agents near you or technical support in our 24 23 22 21 20 company as soon as possible. 2. 3 years warranty since the delivery date. During the period of SoutSou t+ NC NC NC NC NC Sin+ Sin- TxxxxD 1 2 3 4 5 9 10 11 12 quality guarantee，our company will repair or change free of charge if product has any quality problem in the process of normally using. APPLICATION CIRCUITS Input Out put See A GUIDE TO INSTRUMENTATION ISOLATION AMPLIFIERS for more detail. PACKAGING SIZE AND TERMINAL DESCRIPTION First Angle Projection SOIC Package 0.70 (0.028) 4.00 (0.157) 27.94(1.100) 32.30(1.272) 14.40 (0.560) 14.40 (0.560) 18.60(0.732) 32.30(1.272) 0.65 (0.026) 10.20 (0.397) 10.20 (0.397) DIP Package RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) (0.028) 1.15±0.15 16 151413 24232221 20 2.00 (0.079) Vin- 19.24(0.757) 24 23 22 21 20 1 2 3 4 5 1615 1413 Vin- 0.30 (0.012) 1 2 3 4 5 9 1011 12 9 1011 12 1.00 (0.039) FOOTPRINT DETAILS PIN FUNCTION PIN OutputOutput+ Input+ FUNCTION Isolation Power Output+ Power Supply+ 24(Vin-) Others Power SupplyNC Isolation Power OutputNC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin tolerances:±0.10mm(±0.004inch) General tolerances :±0.25mm( ±0.010inch) The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T11/12/21/22_D/S A/2-2008 Page 2 of 2