ACTIVE SIGNAL AMPLIFIER Iin & Vout T15/16/25/26_D/S DESCRIPTION PRODUCT PROGRAM The series is a high integration, high efficiency polygonal - line active isolation amplifier module, with anterior circuit current Part Number Power Supply Input Output Isolation Channels Power Output T1530D/S 24V 4-20mA 0-10V NONE 1 T1533D/S 24V 4-20mA 0-10V 24V 1 efficiency isolated micro-power source, which T1630D/S 24V 4-20mA 0-5V NONE 1 can provide a electrics-feed for signal input. In T1650D/S 12V 4-20mA 0-5V NONE 1 signal input and posterior current signal output. These modules are embed with a high the two-wire three-wire and four-wire circuit applications, our products largely predigest Note: We could also offer customer design for special input and output. customers’ design helpfully improve the using room ratio of PCB. Adopting electromagnetism isolation technology, it is available to keep high accuracy and natural extremely ELECTRICAL CHARACTERISTICS temperature drift. The isolation voltage among Power Supply Data the input, output, power supply and isolated power output can up to 2.5KVDC. FEATURES Isolation Power Output Data Input Data ● Four-port isolation（Among input, output, power supply and Isolation Power output） ● High accuracy (0.1% F.S.) Power Supply ±5% Power Supply low Output Data ● High linearity (0.1% F.S.) Power Dissipation ≤2W Power Protection Reverse protection Output Voltage (Nominal) ±10% Output Current ≤25mA Input Signal Input Impedance See above Overload ≤300mA Output Signal See above Load ＞1KΩ（At output=max） Voltage Drop≤250mV(At input=20mA) ● Isolation voltage(2500VDC/60S) ● High frequency response(15KHz) TRANSMISSION CHARACTERISTICS ● Extremely low temperature(35PPM/℃) Offset ● Industry standard(Operating Temperature Gain Error 0.1%F.S. Temperature Drift 0.0035%F.S./℃ (-25℃ to +71 ℃) Range:-25°C to 71°C) ● High reliability(MTBF＞500,000 hours) 0.1%F.S. ISOLATION CHARACTERISTICS MODEL SELECTION TXXXXD Pa ckage style Iso lation po w er o utpu t Pow e r supp ly Out put Inp ut Isolatio n Amp lifier MORNSUN Science & Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com Galvanic Isolation Four-port isolation（Among input, output, power supply and Isolation Power output） Isolation Voltage 2.5KVDC (Tested for 1minute and 1mA max, humidity < 70%) Insulation Resistance 1000MΩ,500VDC (Among signal input ,signal output ,power supply and isolation power output) OTHER CHARACTERISTICS Ambient temperature Operation temperature:-25℃ to +71℃ Transport and Storage temperature:-50℃ to +105℃ Package DIP24/SOIC24 Weight About 10g The Environment in use No dusts, gases of fiercely vibration, impulsion or gases that may erode to the components surrounded Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. Only typical models listed, specifications of custom product may be different. Please contact our service people directly for certain conditions. The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T15/16/25/26_D/S A/2-2008 Page 1 of 2 SCHEMATIC DIAGRAM APPLICATION NOTE 24Power supply 23+ 1. Please read instruction book carefully before using the product. If you have any question, please contact with our technical support. 13- 2. Please don’t install in the dangerous zone. Isolation Power Output 14+ 3. The power supply is direct voltage. 220V alternating current is forbidden.. Vout+ 3+ Iin12Signal input 11+ Ii n+ 4. Don’t divide the product privately in case the Signal output Vout- equipments ineffective or go wrong. 1- AFTER SERVICE 1. Products are carefully inspected and controlled APPLICATION CIRCUIT DIAGRAM before going out from our factory. If they operated abnormally or there were something Power Supply wrong in the inner parts, please contact with our Isolation Power Output agents near you or technical support in our 16 15 14 13 PinPin+ NC NC NC NC NC PoutPout+ company as soon as possible. 24 23 22 21 20 2. 3 years warranty since the delivery date. During the period of SoutNC Sout+ NC NC NC NC Sin + Sin - TxxxxD 1 2 3 4 5 9 10 11 12 has any quality problem in the process of normally using. APPLICATION CIRCUITS Input Output quality guarantee，our company will repair or change free of charge if product See A GUIDE TO INSTRUMENTATION ISOLATION AMPLIFIERS for more detail. PACKAGING SIZE AND TERMINAL DESCRIPTION First Angle Projection DIP Package 4.00 (0.157) 0.70 (0.028) 32.30(1.272) 14.40 (0.560) 14.40 (0.560) 18.60 (0.732) 32.30(1.272) 27.94 (1.100) 0.30 (0.012) RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) 1.15±0.15 (0.0 45±0.006) 24 23 22 21 20 16 15 14 13 24 23 22 21 20 1 2 3 4 5 1 2 3 4 5 16 15 14 13 Vin- 2.00 0.079 Vin- 19.24 (0.757) 0.65 (0.026) 10.20 (0.397) 10.20 (0.397) SOIC Package 9 1011 12 9 1011 12 1.00 0.039 Pin C onnection FUNCTION PIN PIN Output- FUNCTION Isolation Power Output+ Output+ Input+ Power Sup ply+ 24(Vin-) Power Supply- Others NC Isolation Power OutputNC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin tolerances:± 0.10mm(± 0.004inch) General tolerances :±0.25mm(± 0.010inch) The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T15/16/25/26_D/S A/2-2008 Page 2 of 2