RAMTRON FM31L272-G

FM31L278/L276/L274/L272
3V Integrated Processor Companion with Memory
Features
High Integration Device Replaces Multiple Parts
• Serial Nonvolatile Memory
• Real-time Clock (RTC)
• Low Voltage Reset
• Watchdog Timer
• Early Power-Fail Warning/NMI
• Two 16-bit Event Counters
• Serial Number with Write-lock for Security
Processor Companion
• Active-low Reset Output for VDD and Watchdog
• Programmable VDD Reset Trip Point
• Manual Reset Filtered and Debounced
• Programmable Watchdog Timer
• Dual Battery-backed Event Counter Tracks
System Intrusions or other Events
• Comparator for Early Power-Fail Interrupt
• 64-bit Programmable Serial Number with Lock
Ferroelectric Nonvolatile RAM
• 4Kb, 16Kb, 64Kb, and 256Kb versions
• Unlimited Read/Write Endurance
• 45 year Data Retention
• NoDelay™ Writes
Fast Two-wire Serial Interface
• Up to 1 MHz Maximum Bus Frequency
• Supports Legacy Timing for 100 kHz & 400 kHz
• Device Select Pins for up to 4 Memory Devices
• RTC, Supervisor Controlled via 2-wire Interface
Real-time Clock/Calendar
• Backup Current under 1 µA
• Seconds through Centuries in BCD format
• Tracks Leap Years through 2099
• Uses Standard 32.768 kHz Crystal (12.5pF)
• Software Calibration
• Supports Battery or Capacitor Backup
Easy to Use Configurations
• Operates from 2.7 to 3.6V
• 14-pin “Green”/RoHS SOIC package (-G)
• Low Operating Current
• -40°C to +85°C Operation
• Underwriters Laboratory (UL) Recognized
Description
The processor companion includes commonly needed
CPU support functions. Supervisory functions
include a reset output signal controlled by either a
low VDD condition or a watchdog timeout. /RST
goes active when VDD drops below a programmable
threshold and remains active for 100 ms after VDD
rises above the trip point. A programmable watchdog
timer runs from 100 ms to 3 seconds. The watchdog
timer is optional, but if enabled it will assert the reset
signal for 100 ms if not restarted by the host before
the timeout. A flag-bit indicates the source of the
reset.
The FM31L27x is a family of integrated devices that
includes the most commonly needed functions for
processor-based systems. Major features include
nonvolatile memory available in various sizes, realtime clock, low-VDD reset, watchdog timer,
nonvolatile event counter, lockable 64-bit serial
number area, and general purpose comparator that
can be used for an early power-fail (NMI) interrupt or
other purpose. The family operates from 2.7 to 3.6V.
Each FM31L27x provides nonvolatile RAM
available in sizes including 4Kb, 16Kb, 64Kb, and
256Kb versions. Fast write speed and unlimited
endurance allow the memory to serve as extra RAM
or conventional nonvolatile storage. This memory is
truly nonvolatile rather than battery backed.
The real-time clock (RTC) provides time and date
information in BCD format. It can be permanently
powered from external backup voltage source, either
a battery or a capacitor. The timekeeper uses a
common external 32.768 kHz crystal and provides a
calibration mode that allows software adjustment of
timekeeping accuracy.
This product conforms to specifications per the terms of the Ramtron
standard warranty. The product has completed Ramtron’s internal
qualification testing and has reached production status.
Rev. 3.0
Feb. 2009
A general-purpose comparator compares an external
input pin to the onboard 1.2V reference. This is
useful for generating a power-fail interrupt (NMI) but
can be used for any purpose. The family also includes
a programmable 64-bit serial number that can be
locked making it unalterable. Additionally it offers a
dual battery-backed event counter that tracks the
number of rising or falling edges detected on
dedicated input pins.
Ramtron International Corporation
1850 Ramtron Drive, Colorado Springs, CO 80921
(800) 545-FRAM, (719) 481-7000
http://www.ramtron.com
Page 1 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Pin Configuration
CNT1
1
14
VDD
CNT2
2
13
SCL
A0
3
12
SDA
A1
4
11
X2
5
10
X1
RST
6
9
PFI
VSS
7
8
VBAK
CAL/PFO
Pin Name
CNT1, CNT2
A0, A1
CAL/PFO
/RST
PFI
X1, X2
SDA
SCL
VBAK
VDD
VSS
Function
Event Counter Inputs
Device Select inputs
Clock Calibration and Early
Power-Fail Output
Reset Input/Output
Early Power-fail Input
Crystal Connections
Serial Data
Serial Clock
Battery-Backup Supply
Supply Voltage
Ground
Ordering Information
Base Configuration
FM31L278
FM31L276
FM31L274
FM31L272
Memory Size
256Kb
256Kb
64Kb
64Kb
16Kb
16Kb
4Kb
4Kb
Operating Voltage
2.7-3.6V
2.7-3.6V
2.7-3.6V
2.7-3.6V
2.7-3.6V
2.7-3.6V
2.7-3.6V
2.7-3.6V
Reset Threshold
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
2.6V, 2.9V
Ordering Part Number
FM31L278-G
FM31L278-GTR (tape&reel)
FM31L276-G
FM31L276-GTR (tape&reel)
FM31L274-G
FM31L274-GTR (tape&reel)
FM31L272-G
FM31L272-GTR (tape&reel)
Other memory configurations may be available. Please contact the factory for more information.
Rev. 3.0
Feb. 2009
Page 2 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
SCL
2-Wire
Interface
SDA
LockOut
A1, A0
F-RAM
Array
LockOut
RST
Watchdog
Special
Function
Registers
LV Detect
S/N
RTC Registers
X1
RTC Cal.
PFI
+
-
CAL/PFO
2.5V
1.2V
RTC
X2
512Hz
-
Event
Counters
+
VDD
CNT1
CNT2
Switched Power
VBAK
Nonvolatile
Battery Backed
Figure 1. Block Diagram
Pin Descriptions
Pin Name
A0, A1
Type
Input
CNT1,
CNT2
Input
CAL/PFO
Output
X1, X2
I/O
/RST
SDA
I/O
I/O
SCL
Input
PFI
Input
VBAK
Supply
VDD
VSS
Supply
Supply
Rev. 3.0
Feb. 2009
Pin Description
Device select inputs are used to address multiple memories on a serial bus. To select the
device the address value on the two pins must match the corresponding bits contained in
the device address. The device select pins are pulled down internally.
Event Counter Inputs: These battery-backed inputs increment counters when an edge is
detected on the corresponding CNT pin. The polarity is programmable. These pins
should not be left floating. Tie to ground if these pins are not used.
In calibration mode, this pin supplies a 512 Hz square-wave output for clock calibration.
In normal operation, this is the early power-fail output.
32.768 kHz crystal connection. When using an external oscillator, apply the clock to X1
and a DC mid-level to X2 (see Crystal Oscillator section for suggestions).
Active low reset output with weak pull-up. Also input for manual reset.
Serial Data & Address: This is a bi-directional line for the two-wire interface. It is opendrain and is intended to be wire-OR’d with other devices on the two-wire bus. The input
buffer incorporates a Schmitt trigger for noise immunity and the output driver includes
slope control for falling edges. A pull-up resistor is required.
Serial Clock: The serial clock line for the two-wire interface. Data is clocked out of the
part on the falling edge, and in on the rising edge. The SCL input also incorporates a
Schmitt trigger input for noise immunity.
Early Power-fail Input: Typically connected to an unregulated power supply to detect an
early power failure. This pin should not be left floating.
Backup supply voltage: A 3V battery or a large value capacitor. If no backup supply is
used, this pin should be tied to ground and the VBC bit should be cleared. The trickle
charger is UL recognized and ensures no excessive current when using a lithium battery.
Supply Voltage
Ground
Page 3 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Overview
The FM31L27x family combines a serial nonvolatile
RAM with a real-time clock (RTC) and a processor
companion. The companion is a highly integrated
peripheral including a processor supervisor, a
comparator used for early power-fail warning,
nonvolatile event counters, and a 64-bit serial
number.
The
FM31L27x
integrates
these
complementary but distinct functions that share a
common interface in a single package. Although
monolithic, the product is organized as two logical
devices,
the
F-RAM
memory
and
the
RTC/companion. From the system perspective they
appear to be two separate devices with unique IDs on
the serial bus.
The memory is organized as a stand-alone 2-wire
nonvolatile memory with a standard device ID value.
The real-time clock and supervisor functions are
accessed with a separate 2-wire device ID. This
allows clock/calendar data to be read while
maintaining the most recently used memory address.
The clock and supervisor functions are controlled by
25 special function registers. The RTC and event
counter circuits are maintained by the power source
on the VBAK pin, allowing them to operate from
battery or backup capacitor power when VDD drops
below an internally set threshold. Each functional
block is described below.
Memory Operation
The FM31L27x is a family of products available in
different memory sizes including 4Kb, 16Kb, 64Kb,
and 256Kb. The family is software compatible, all
versions use consistent two-byte addressing for the
memory device. This makes the lowest density
device different from its stand-alone memory
counterparts but makes them compatible within the
entire family.
Memory is organized in bytes, for example the 4Kb
memory is 512 x 8 and the 256Kb memory is 32,768
x 8. The memory is based on F-RAM technology.
Therefore it can be treated as RAM and is read or
written at the speed of the two-wire bus with no
delays for write operations. It also offers effectively
unlimited write endurance unlike other nonvolatile
memory technologies. The 2-wire interface protocol
is described further on page 13.
The memory array can be write-protected by
software. Two bits in the processor companion area
(WP0, WP1 in register 0Bh) control the protection
setting as shown in the following table. Based on the
setting, the protected addresses cannot be written and
the 2-wire interface will not acknowledge any data to
Rev. 3.0
Feb. 2009
protected addresses. The special function registers
containing these bits are described in detail below.
Write protect addresses
None
Bottom 1/4
Bottom 1/2
Full array
WP1
0
0
1
1
WP0
0
1
0
1
Processor Companion
In addition to nonvolatile RAM, the FM31L27x
family incorporates a highly integrated processor
companion. It includes a low voltage reset, a
programmable watchdog timer, battery-backed event
counters, a comparator for early power-fail detection
or other purposes, and a 64-bit serial number.
Processor Supervisor
Supervisors provide a host processor two basic
functions: detection of power supply fault conditions
and a watchdog timer to escape a software lockup
condition. All FM31L27x devices have a reset pin
(/RST) to drive the processor reset input during
power faults (and power-up) and software lockups. It
is an open drain output with a weak internal pull-up
to VDD. This allows other reset sources to be wireOR’d to the /RST pin. When VDD is above the
programmed trip point, /RST output is pulled weakly
to VDD. If VDD drops below the reset trip point
voltage level (VTP) the /RST pin will be driven low. It
will remain low until VDD falls too low for circuit
operation which is the VRST level. When VDD rises
again above VTP, /RST will continue to drive low for
at least 100 ms (tRPU) to ensure a robust system reset
at a reliable VDD level. After tRPU has been met, the
/RST pin will return to the weak high state. While
/RST is asserted, serial bus activity is locked out even
if a transaction occurred as VDD dropped below VTP.
A memory operation started while VDD is above VTP
will be completed internally.
Figure 2 below illustrates the reset operation in
response to the VDD voltage.
VDD
tRPU
VTP
RST
Figure 2. Low Voltage Reset
The bit VTP controls the trip point of the low voltage
detect circuit. It is located in register 0Bh, bit 0. Note
that the bit 1 location is a “don’t care”.
Page 4 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
VTP
2.6V
2.9V
VTP
0
1
The watchdog timer can also be used to assert the
reset signal (/RST). The watchdog is a free running
programmable timer. The period can be software
programmed from 100 ms to 3 seconds in 100 ms
increments via a 5-bit nonvolatile register. All
programmed settings are minimum values and vary
with temperature according to the operating
specifications. The watchdog has two additional
controls associated with its operation, a watchdog
enable bit (WDE) and timer restart bits (WR). Both
the enable bit must be set and the watchdog must
timeout in order to drive /RST active. If a reset event
occurs, the timer will automatically restart on the
rising edge of the reset pulse. If WDE=0, the
watchdog timer runs but a watchdog fault will not
cause /RST to be asserted low. The WTR flag will be
set, indicating a watchdog fault. This setting is useful
during software development and the developer does
not want /RST to drive. Note that setting the
maximum timeout setting (11111b) disables the
counter to save power. The second control is a nibble
that restarts the timer preventing a reset. The timer
should be restarted after changing the timeout value.
The watchdog timeout value is located in register
0Ah, bits 4-0, and the watchdog enable is bit 7. The
watchdog is restarted by writing the pattern 1010b to
the lower nibble of register 09h. Writing this pattern
will also cause the timer to load new timeout values.
Writing other patterns to this address will not affect
its operation. Note the watchdog timer is freerunning. Prior to enabling it, users should restart the
timer as described above. This assures that the full
timeout period will be set immediately after enabling.
The watchdog is disabled when VDD is below VTP.
The following table summarizes the watchdog bits. A
block diagram follows.
Watchdog timeout
Watchdog enable
Watchdog restart
100 ms
clock
Timebase
WDT4-0
WDE
WR3-0
Manual Reset
The /RST pin is bi-directional and allows the
FM31L27x to filter and de-bounce a manual reset
switch. The /RST input detects an external low
condition and responds by driving the /RST signal
low for 100 ms.
MCU
RST
FM31L27x
Reset
Switch
Switch
Behavior
RST
FM31L27x
drives
100 ms (min.)
Figure 4. Manual Reset
Note that an internal weak pull-up on /RST
eliminates the need for additional external
components.
Reset Flags
In case of a reset condition, a flag will be set to
indicate the source of the reset. A low VDD reset or
manual reset is indicated by the POR flag, register
09h bit 6. A watchdog reset is indicated by the WTR
flag, register 09h bit 7. Note that the flags are
internally set in response to reset sources, but they
must be cleared by the user. When the register is
read, it is possible that both flags are set if both have
occurred since the user last cleared them.
Early Power Fail Comparator
An early power fail warning can be provided to the
processor well before VDD drops out of spec. The
comparator is used to create a power fail interrupt
(NMI). This can be accomplished by connecting the
PFI pin to the unregulated power supply via a resistor
divider. An application circuit is shown below.
0Ah, bits 4-0
0Ah, bit 7
09h, bits 3-0
Regulator
VDD
WR3-0 = 1010b to restart
Counter
Watchdog
timeout
FM31L27x
/RST
WDE
PFI
To MCU CAL/PFO
NMI input
+
-
1.2V ref
Figure 3. Watchdog Timer
Figure 5. Comparator as Early Power-Fail Warning
Rev. 3.0
Feb. 2009
Page 5 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
The voltage on the PFI input pin is compared to an
onboard 1.2V reference. When the PFI input voltage
drops below this threshold, the comparator will drive
the CAL/PFO pin to a low state. The comparator has
100 mV (max) of hysteresis to reduce noise
sensitivity, only for a rising PFI signal. For a falling
PFI edge, there is no hysteresis.
The comparator is a general purpose device and its
application is not limited to the NMI function.
The comparator is not integrated into the special
function registers except as it shares its output pin
with the CAL output. When the RTC calibration
mode is invoked by setting the CAL bit (register 00h,
bit 2), the CAL/PFO output pin will be driven with a
512 Hz square wave and the comparator will be
ignored. Since most users only invoke the calibration
mode during production, this should have no impact
on system operations using the comparator.
Note: The maximum voltage on the comparator input PFI
is limited to 3.75V under normal operating conditions.
Event Counter
The FM31L27x offers the user two battery-backed
event counters. Input pins CNT1 and CNT2 are
programmable edge detectors. Each clocks a 16-bit
counter. When an edge occurs, the counters will
increment their respective registers. Counter 1 is
located in registers 0Dh and 0Eh, Counter 2 is
located in registers 0Fh and 10h. These register
values can be read anytime VDD is above VTP, and
they will be incremented as long as a valid VBAK
power source is provided. To read, set the RC bit
register 0Ch bit 3 to 1. This takes a snapshot of all
four counter bytes allowing a stable value even if a
count occurs during the read. The registers can be
written by software allowing the counters to be
cleared or initialized by the system. Counts are
blocked during a write operation. The two counters
can be cascaded to create a single 32-bit counter by
setting the CC control bit (register 0Ch). When
cascaded, the CNT1 input will cause the counter to
increment. CNT2 is not used in this mode.
C1P
16-bit Counter
CNT1
C2P
CNT2
16-bit Counter
CC
Figure 6. Event Counter
Rev. 3.0
Feb. 2009
The control bits for event counting are located in
register 0Ch. Counter 1 Polarity is bit C1P, bit 0;
Counter 2 Polarity is C2P, bit 1; the Cascade Control
is CC, bit 2; and the Read Counter bit is RC bit 3.
The polarity bits must be set prior to setting the
counter value(s). If a polarity bit is changed, the
counter may inadvertently increment. If the counter
pins are not being used, tie them to ground.
Serial Number
A memory location to write a 64-bit serial number is
provided. It is a writeable nonvolatile memory block
that can be locked by the user once the serial number
is set. The 8 bytes of data and the lock bit are all
accessed via the device ID for the processor
companion. Therefore the serial number area is
separate and distinct from the memory array. The
serial number registers can be written an unlimited
number of times, so these locations are general
purpose memory. However once the lock bit is set the
values cannot be altered and the lock cannot be
removed. Once locked the serial number registers can
still be read by the system.
The serial number is located in registers 11h to 18h.
The lock bit is SNL, register 0Bh bit 7. Setting the
SNL bit to a 1 disables writes to the serial number
registers, and the SNL bit cannot be cleared.
Real-Time Clock Operation
The real-time clock (RTC) is a timekeeping device
that can be battery or capacitor backed for
permanently-powered operation. It offers a software
calibration feature that allows high accuracy.
The RTC consists of an oscillator, clock divider, and
a register system for user access. It divides down the
32.768 kHz time-base and provides a minimum
resolution of seconds (1Hz). Static registers provide
the user with read/write access to the time values. It
includes registers for seconds, minutes, hours, dayof-the-week, date, months, and years. A block
diagram (Figure 7) illustrates the RTC function.
The user registers are synchronized with the
timekeeper core using R and W bits in register 00h
described below. Changing the R bit from 0 to 1
transfers timekeeping information from the core into
holding registers that can be read by the user. If a
timekeeper update is pending when R is set, then the
core will be updated prior to loading the user
registers. The registers are frozen and will not be
updated again until the R bit is cleared to 0. R is used
for reading the time.
Setting the W bit to 1 locks the user registers.
Clearing it to 0 causes the values in the user registers
Page 6 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
to be loaded into the timekeeper core. W is used for
writing new time values. Users should be certain not
to load invalid values, such as FFh, to the
timekeeping registers. Updates to the timekeeping
core occur continuously except when locked.
Trickle Charger
To facilitate capacitor backup the VBAK pin can
optionally provide a trickle charge current. When the
VBC bit, register 0Bh bit 2, is set to ‘1’, the VBAK pin
will source approximately 80 µA until VBAK reaches
VDD. This charges the capacitor to VDD without an
external diode and resistor charger. There is a Fast
Charge mode which is enabled by the FC bit (register
0Bh, bit 5). In this mode the trickle charger current is
set to approximately 1 mA, allowing a large backup
capacitor to charge more quickly.
Backup Power
The real-time clock/calendar is intended to be
permanently powered. When the primary system
power fails, the voltage on the VDD pin will drop.
When VDD is less 2.5V the RTC (and event counters)
will switch to the backup power supply on VBAK. The
clock operates at extremely low current in order to
maximize battery or capacitor life. However, one of
the advantages of combining a clock function with
the F-RAM memory is that data is not lost regardless
of the backup power source.
In the case where no backup supply is used, the VBAK
pin should be tied to VSS. Be sure to turn off the
trickle charger (VBC=0), otherwise charger current
will be shunted to ground from VDD.
! Note: systems using lithium batteries should clear
the VBC bit to 0 to prevent battery charging. The
VBAK circuitry includes an internal 1 KΩ series
resistor as a safety element. The trickle charger is UL
Recognized.
A battery may be inserted into a system board
without any concern for excessive current draw on
the FM31L27x’s VBAK pin.
512 Hz
/OSCEN
32.768 kHz
crystal
CF
Years
8 bits
Months
5 bits
Clock
Divider
Oscillator
Date
6 bits
Hours
6 bits
1 Hz
Minutes
7 bits
W
Update
Logic
Seconds
7 bits
Days
3 bits
User Interface Registers
R
Figure 7. Real-Time Clock Core Block Diagram
Calibration
When the CAL bit in a register 00h is set to 1, the
clock enters calibration mode. In calibration mode,
the CAL/PFO output pin is dedicated to the
calibration function and the power fail output is
temporarily unavailable. Calibration operates by
applying a digital correction to the counter based on
the frequency error. In this mode, the CAL/PFO pin
is driven with a 512 Hz (nominal) square wave. Any
measured deviation from 512 Hz translates into a
timekeeping error. The user converts the measured
error in ppm and writes the appropriate correction
value to the calibration register. The correction
factors are listed in the table below. Positive ppm
errors require a negative adjustment that removes
Rev. 3.0
Feb. 2009
pulses. Negative ppm errors require a positive
correction that adds pulses. Positive ppm adjustments
have the CALS (sign) bit set to 1, where as negative
ppm adjustments have CALS = 0. After calibration,
the clock will have a maximum error of ± 2.17 ppm
or ± 0.09 minutes per month at the calibrated
temperature.
The calibration setting is stored in F-RAM so is not
lost should the backup source fail. It is accessed with
bits CAL.4-0 in register 01h. This value only can be
written when the CAL bit is set to a 1. To exit the
calibration mode, the user must clear the CAL bit to a
0. When the CAL bit is 0, the CAL/PFO pin will
revert to the power fail output function.
Page 7 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Crystal Oscillator
The crystal oscillator is designed to use a 12.5pF
crystal without the need for external components,
such as loading capacitors. The FM31L27x device
has built-in loading capacitors that match the crystal.
If a 32.768kHz crystal is not used, an external
oscillator may be connected to the FM31L27x.
Apply the oscillator to the X1 pin. Its high and low
voltage levels can be driven rail-to-rail or amplitudes
as low as approximately 500mV p-p. To ensure
proper operation, a DC bias must be applied to the
X2 pin. It should be centered between the high and
low levels on the X1 pin. This can be accomplished
with a voltage divider.
In the example, R1 and R2 are chosen such that the
X2 voltage is centered around the X1 oscillator drive
levels. If you wish to avoid the DC current, you may
choose to drive X1 with an external clock and X2
with an inverted clock using a CMOS inverter.
Rev. 3.0
Feb. 2009
FM31L27x
X1 X2
Vdd
R1
R2
Figure 8. External Oscillator
Layout Requirements
The X1 and X2 crystal pins employ very high
impedance circuits and the oscillator connected to
these pins can be upset by noise or extra loading. To
reduce RTC clock errors from signal switching noise,
a guard ring must be placed around these pads and
the guard ring grounded. SDA and SCL traces should
be routed away from the X1/X2 pads. The X1 and X2
trace lengths should be less than 5 mm. The use of a
ground plane on the backside or inner board layer is
preferred. See layout example. Red is the top layer,
green is the bottom layer.
VDD
VDD
SCL
SCL
SDA
SDA
X2
X2
X1
X1
PFI
PFI
VBAK
VBAK
Layout for Surface Mount Crystal
Layout for Through Hole Crystal
(red = top layer, green = bottom layer)
(red = top layer, green = bottom layer)
Page 8 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Calibration Adjustments
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Positive Calibration for slow clocks: Calibration will achieve ± 2.17 PPM after calibration
Measured Frequency Range
Error Range (PPM)
Min
Max
Min
Max
Program Calibration Register to:
512.0000
511.9989
0
2.17
000000
511.9989
511.9967
2.18
6.51
100001
511.9967
511.9944
6.52
10.85
100010
511.9944
511.9922
10.86
15.19
100011
511.9922
511.9900
15.20
19.53
100100
511.9900
511.9878
19.54
23.87
100101
511.9878
511.9856
23.88
28.21
100110
511.9856
511.9833
28.22
32.55
100111
511.9833
511.9811
32.56
36.89
101000
511.9811
511.9789
36.90
41.23
101001
511.9789
511.9767
41.24
45.57
101010
511.9767
511.9744
45.58
49.91
101011
511.9744
511.9722
49.92
54.25
101100
511.9722
511.9700
54.26
58.59
101101
511.9700
511.9678
58.60
62.93
101110
511.9678
511.9656
62.94
67.27
101111
511.9656
511.9633
67.28
71.61
110000
511.9633
511.9611
71.62
75.95
110001
511.9611
511.9589
75.96
80.29
110010
511.9589
511.9567
80.30
84.63
110011
511.9567
511.9544
84.64
88.97
110100
511.9544
511.9522
88.98
93.31
110101
511.9522
511.9500
93.32
97.65
110110
511.9500
511.9478
97.66
101.99
110111
511.9478
511.9456
102.00
106.33
111000
511.9456
511.9433
106.34
110.67
111001
511.9433
511.9411
110.68
115.01
111010
511.9411
511.9389
115.02
119.35
111011
511.9389
511.9367
119.36
123.69
111100
511.9367
511.9344
123.70
128.03
111101
511.9344
511.9322
128.04
132.37
111110
511.9322
511.9300
132.38
136.71
111111
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Negative Calibration for fast clocks: Calibration will achieve ± 2.17 PPM after calibration
Measured Frequency Range
Error Range (PPM)
Min
Max
Min
Max
Program Calibration Register to:
512.0000
512.0011
0
2.17
000000
512.0011
512.0033
2.18
6.51
000001
512.0033
512.0056
6.52
10.85
000010
512.0056
512.0078
10.86
15.19
000011
512.0078
512.0100
15.20
19.53
000100
512.0100
512.0122
19.54
23.87
000101
512.0122
512.0144
23.88
28.21
000110
512.0144
512.0167
28.22
32.55
000111
512.0167
512.0189
32.56
36.89
001000
512.0189
512.0211
36.90
41.23
001001
512.0211
512.0233
41.24
45.57
001010
512.0233
512.0256
45.58
49.91
001011
512.0256
512.0278
49.92
54.25
001100
512.0278
512.0300
54.26
58.59
001101
512.0300
512.0322
58.60
62.93
001110
512.0322
512.0344
62.94
67.27
001111
512.0344
512.0367
67.28
71.61
010000
512.0367
512.0389
71.62
75.95
010001
512.0389
512.0411
75.96
80.29
010010
512.0411
512.0433
80.30
84.63
010011
512.0433
512.0456
84.64
88.97
010100
512.0456
512.0478
88.98
93.31
010101
512.0478
512.0500
93.32
97.65
010110
512.0500
512.0522
97.66
101.99
010111
512.0522
512.0544
102.00
106.33
011000
512.0544
512.0567
106.34
110.67
011001
512.0567
512.0589
110.68
115.01
011010
512.0589
512.0611
115.02
119.35
011011
512.0611
512.0633
119.36
123.69
011100
512.0633
512.0656
123.70
128.03
011101
512.0656
512.0678
128.04
132.37
011110
512.0678
512.0700
132.38
136.71
011111
Rev. 3.0
Feb. 2009
Page 9 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Register Map
The RTC and processor companion functions are accessed via 25 special function registers mapped to a separate 2wire device ID. The interface protocol is described below. The registers contain timekeeping data, control bits, or
information flags. A description of each register follows the summary table below.
Register Map Summary Table
Nonvolatile =
Battery-backed =
Address
18h
17h
16h
15h
14h
13h
12h
11h
10h
0Fh
0Eh
0Dh
0Ch
0Bh
0Ah
09h
08h
07h
06h
05h
04h
03h
02h
01h
00h
D7
SNL
WDE
WTR
0
0
0
0
0
0
/OSCEN
reserved
D6
D5
D4
D3
Serial Number Byte 7
Serial Number Byte 6
Serial Number Byte 5
Serial Number Byte 4
Serial Number Byte 3
Serial Number Byte 2
Serial Number Byte 1
Serial Number Byte 0
Counter 2 MSB
Counter 2 LSB
Counter 1 MSB
Counter 1 LSB
RC
FC
WP1
WP0
WDT4
WDT3
POR
LB
WR3
10 years
0
0
10 mo
0
10 date
0
0
0
0
0
10 hours
10 minutes
10 seconds
reserved
CALS
CAL4
CAL3
CF
reserved reserved reserved
D2
D1
CC
C2P
VBC
WDT2
WDT1
WR2
WR1
years
months
date
day
hours
minutes
seconds
CAL2
CAL1
CAL
W
D0
C1P
VTP
WDT0
WR0
CAL0
R
Function
Serial Number 7
Serial Number 6
Serial Number 5
Serial Number 4
Serial Number 3
Serial Number 2
Serial Number 1
Serial Number 0
Event Counter 2 MSB
Event Counter 2 LSB
Event Counter 1 MSB
Event Counter 1 LSB
Event Count Control
Companion Control
Watchdog Control
Watchdog Restart/Flags
Years
Month
Date
Day
Hours
Minutes
Seconds
CAL/Control
RTC Control
Range
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
00-99
1-12
1-31
1-7
0-23
0-59
0-59
Note: When the device is first powered up and programmed, all registers must be written because the batterybacked register values cannot be guaranteed. The table below shows the default values of the non-volatile
registers. All other register values should be treated as unknown.
Default Register Values
Address
18h
17h
16h
15h
14h
13h
12h
11h
0Bh
0Ah
01h
Rev. 3.0
Feb. 2009
Hex Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x1F
0x80
Page 10 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Register Description
Address Description
18h
Serial Number Byte 7
D7
D6
D5
D4
D3
D2
D1
D0
SN.63
SN.62
SN.61
SN.60
SN.59
SN.58
SN.57
SN.56
Upper byte of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
17h
Serial Number Byte 6
D7
D6
D5
D4
D3
D2
D1
D0
SN.55
SN.54
SN.53
SN.52
SN.51
SN.50
SN.49
SN.48
Byte 6 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
16h
Serial Number Byte 5
D7
D6
D5
D4
D3
D2
D1
D0
SN.47
SN.46
SN.45
SN.44
SN.43
SN.42
SN.41
SN.40
Byte 5 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
15h
Serial Number Byte 4
D7
D6
D5
D4
D3
D2
D1
D0
SN.39
SN.38
SN.37
SN.36
SN.35
SN.34
SN.33
SN.32
Byte 4 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
14h
Serial Number Byte 3
D7
D6
D5
D4
D3
D2
D1
D0
SN.31
SN.30
SN.29
SN.28
SN.27
SN.26
SN.25
SN.24
Byte 3 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
13h
Serial Number Byte 2
D7
D6
D5
D4
D3
D2
D1
D0
SN.23
SN.22
SN.21
SN.20
SN.19
SN.18
SN.17
SN.16
Byte 2 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
12h
Serial Number Byte 1
D7
D6
D5
D4
D3
D2
D1
D0
SN.15
SN.14
SN.13
SN.12
SN.11
SN.10
SN.9
SN.8
Byte 1 of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
11h
Serial Number Byte 0
D7
D6
D5
D4
D3
D2
D1
D0
SN.7
SN.6
SN.5
SN.4
SN.3
SN.2
SN.1
SN.0
LSB of the serial number. Read/write when SNL=0, read-only when SNL=1. Nonvolatile.
10h
Counter 2 MSB
D7
D6
D5
D4
D3
D2
D1
D0
C2.15
C2.14
C2.13
C2.12
C2.11
C2.10
C2.9
C2.8
Event Counter 2 MSB. Increments on overflows from Counter 2 LSB. Battery-backed, read/write.
0Fh
Counter 2 LSB
D7
D6
D5
D4
D3
D2
D1
D0
C2.7
C2.6
C2.5
C2.4
C2.3
C2.2
C2.1
C2.0
Event Counter 2 LSB. Increments on programmed edge event on CNT2 input or overflows from Counter 1 MSB
when CC=1. Battery-backed, read/write .
0Eh
Counter 1 MSB
D7
D6
D5
D4
D3
D2
D1
D0
C1.15
C1.14
C1.13
C1.12
C1.11
C1.10
C1.9
C1.8
Event Counter 1 MSB. Increments on overflows from Counter 1 LSB. Battery-backed, read/write.
0Dh
Counter 1 LSB
D7
D6
D5
D4
D3
D2
D1
D0
C1.7
C1.6
C1.5
C1.4
C1.3
C1.2
C1.1
C1.0
Event Counter 1 LSB. Increments on programmed edge event on CNT1 input. Battery-backed, read/write.
Rev. 3.0
Feb. 2009
Page 11 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
0Ch
RC
CC
C2P
C1P
0Bh
SNL
FC
WP1-0
Event Counter Control
D7
D6
D5
D4
D3
D2
D1
D0
-
-
-
-
RC
CC
C2P
C1P
Read Counter. Setting this bit to 1 takes a snapshot of the four counters bytes allowing the system to read the
values without missing count events. The RC bit will be automatically cleared.
Counter Cascade. When CC=0, the event counters operate independently according to the edge programmed by
C1P and C2P respectively. When CC=1, the counters are cascaded to create one 32-bit counter. The registers of
Counter 2 represent the most significant 16-bits of the counter and CNT1 is the controlling input. Bit C2P is
“don’t care” when CC=1. Battery-backed, read/write.
CNT2 detects falling edges when C2P = 0, rising edges when C2P = 1. C2P is “don’t care” when CC=1. The value
of Event Counter 2 may inadvertently increment if C2P is changed. Battery-backed, read/write.
CNT1 detects falling edges when C1P = 0, rising edges when C1P = 1. The value of Event Counter 1 may
inadvertently increment if C1P is changed. Battery-backed, read/write.
Companion Control
D7
D6
D5
D4
D3
D2
D1
D0
SNL
-
FC
WP1
WP0
VBC
-
VTP
Serial Number Lock. Setting to a 1 makes registers 11h to 18h and SNL permanently read-only. SNL cannot be
cleared once set to 1. Nonvolatile, read/write.
Fast Charge: Setting FC to ‘1’ (and VBC=1) causes a ~1 mA trickle charge current to be supplied on VBAK.
Clearing VBC to ‘0’ disables the charge current. Nonvolatile, read/write.
Write Protect. These bits control the write protection of the memory array. Nonvolatile, read/write.
Write protect addresses
None
Bottom 1/4
Bottom 1/2
Full array
VBC
WP1
0
0
1
1
WP0
0
1
0
1
VTP
VBAK Charger Control. Setting VBC to ‘1’ (and FC=0) causes a ~80 µA (1 mA if FC=1) trickle charge current to
be supplied on VBAK. Clearing VBC to ‘0’ disables the charge current. Nonvolatile, read/write.
VTP select. This bit controls the reset trip point for the low VDD reset function. Nonvolatile, read/write.
0Ah
Trip Voltage
2.6V
2.9V
Watchdog Control
WDE
WDT4-0
VTP
0
1
D7
D6
D5
D4
D3
D2
D1
D0
WDE
-
-
WDT4
WDT3
WDT2
WDT1
WDT0
Watchdog Enable. When WDE=1, a watchdog timer fault will cause the /RST signal to go active. When WDE = 0
the timer runs but has no effect on /RST, however the WTR flag will be set when a fault occurs. Note as the timer
is free-running, users should restart the timer using WR3-0 prior to setting WDE=1. This assures a full watchdog
timeout interval occurs. Nonvolatile, read/write.
Watchdog Timeout. Indicates the minimum watchdog timeout interval with 100 ms resolution. New watchdog
timeouts are loaded when the timer is restarted by writing the 1010b pattern to WR3-0. Nonvolatile, read/write.
Watchdog timeout
Invalid – default 100 ms
100 ms
200 ms
300 ms
.
.
.
2000 ms
2100 ms
2200 ms
.
.
.
2900 ms
3000 ms
Disable counter
Rev. 3.0
Feb. 2009
WDT4 WDT3 WDT2 WDT1 WDT0
0
0
0
0
0
0
0
0
0
1
0
0
0
1
0
0
0
0
1
1
1
1
1
0
0
0
1
1
1
0
0
1
0
1
0
1
1
1
1
1
1
1
1
1
0
1
1
1
0
1
Page 12 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
09h
WTR
POR
LB
WR3-0
08h
Watchdog Restart & Flags
D7
D6
D5
D4
D3
D2
D1
D0
WTR
POR
LB
-
WR3
WR2
WR1
WR0
Watchdog Timer Reset Flag: When a watchdog timer fault occurs, the WTR bit will be set to 1. It must be cleared
by the user. Note that both WTR and POR could be set if both reset sources have occurred since the flags were
cleared by the user. Battery-backed. Read/Write (internally set, user can clear bit).
Power-on Reset Flag: When the /RST pin is activated by either VDD < VTP or a manual reset, the POR bit will be
set to 1. It must be cleared by the user. Note that both WTR and POR could be set if both reset sources have
occurred since the flags were cleared by the user. Battery-backed. Read/Write (internally set, user can clear bit).
Low Backup Flag: On power up, if the VBAK source is below the minimum voltage to operate the RTC and event
counters, this bit will be set to 1. The user should clear it to 0 when initializing the system. Battery-backed.
Read/Write (internally set, user can clear bit).
Watchdog Restart: Writing a pattern 1010b to WR3-0 restarts the watchdog timer. The upper nibble contents do
not affect this operation. Writing any pattern other than 1010b to WR3-0 has no effect on the timer. This allows
users to clear the WTR, POR, and LB flags without affecting the watchdog timer. Battery-backed, Write-only.
Timekeeping – Years
D7
D6
D5
D4
D3
D2
D1
D0
10 year.3
10 year.2
10 year.1
10 year.0
Year.3
Year.2
Year.1
Year.0
Contains the lower two BCD digits of the year. Lower nibble contains the value for years; upper nibble contains
the value for 10s of years. Each nibble operates from 0 to 9. The range for the register is 0-99. Battery-backed,
read/write.
07h
Timekeeping – Months
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
10 Month
Month.3
Month.2
Month.1
Month.0
Contains the BCD digits for the month. Lower nibble contains the lower digit and operates from 0 to 9; upper
nibble (one bit) contains the upper digit and operates from 0 to 1. The range for the register is 1-12. Batterybacked, read/write.
06h
Timekeeping – Date of the month
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10 date.1
10 date.0
Date.3
Date.2
Date.1
Date.0
Contains the BCD digits for the date of the month. Lower nibble contains the lower digit and operates from 0 to 9;
upper nibble contains the upper digit and operates from 0 to 3. The range for the register is 1-31. Battery-backed,
read/write.
05h
Timekeeping – Day of the week
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
Day.2
Day.1
Day.0
Lower nibble contains a value that correlates to day of the week. Day of the week is a ring counter that counts
from 1 to 7 then returns to 1. The user must assign meaning to the day value, as the day is not integrated with the
date. Battery-backed, read/write.
04h
Timekeeping – Hours
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10 hours.1
10 hours.0
Hours.3
Hours2
Hours.1
Hours.0
Contains the BCD value of hours in 24-hour format. Lower nibble contains the lower digit and operates from 0 to
9; upper nibble (two bits) contains the upper digit and operates from 0 to 2. The range for the register is 0-23.
Battery-backed, read/write.
03h
Timekeeping – Minutes
D7
D6
D5
D4
D3
D2
D1
D0
0
10 min.2
10 min.1
10 min.0
Min.3
Min.2
Min.1
Min.0
Contains the BCD value of minutes. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper minutes digit and operates from 0 to 5. The range for the register is 0-59. Battery-backed,
read/write.
02h
Timekeeping – Seconds
D7
D6
D5
D4
D3
D2
D1
D0
0
10 sec.2
10 sec.1
10 sec.0
Seconds.3
Seconds.2
Seconds.1
Seconds.0
Contains the BCD value of seconds. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper digit and operates from 0 to 5. The range for the register is 0-59. Battery-backed, read/write.
Rev. 3.0
Feb. 2009
Page 13 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
01h
/OSCEN
CAL/Control
D7
D6
D5
D4
D3
D2
D1
D0
OSCEN
Reserved
CALS
CAL.4
CAL.3
CAL.2
CAL.1
CAL.0
CAL.4-0
/Oscillator Enable. When set to 1, the oscillator is halted. When set to 0, the oscillator runs. Disabling the
oscillator can save battery power during storage. On a power-up without battery, this bit is set to 1. Batterybacked, read/write.
Reserved bits. Do not use. Should remain set to 0.
Calibration sign. Determines if the calibration adjustment is applied as an addition to or as a subtraction from
the time-base. Calibration is explained on page 7. Nonvolatile, read/write.
These five bits control the calibration of the clock. Nonvolatile, read/write.
00h
Flags/Control
Reserved
CALS
CF
CAL
W
R
Reserved
Rev. 3.0
Feb. 2009
D7
D6
D5
D4
D3
D2
D1
D0
Reserved
CF
Reserved
Reserved
Reserved
CAL
W
R
Century Overflow Flag. This bit is set to a 1 when the values in the years register overflows from 99 to 00. This
indicates a new century, such as going from 1999 to 2000 or 2099 to 2100. The user should record the new
century information as needed. This bit is cleared to 0 when the Flag register is read. It is read-only for the user.
Battery-backed.
Calibration Mode. When set to 1, the clock enters calibration mode. When CAL is set to 0, the clock operates
normally, and the CAL/PFO pin is controlled by the power fail comparator. Battery-backed, read/write.
Write Time. Setting the W bit to 1 freezes the clock. The user can then write the timekeeping registers with
updated values. Resetting the W bit to 0 causes the contents of the time registers to be transferred to the
timekeeping counters and restarts the clock. Battery-backed, read/write.
Read Time. Setting the R bit to 1 copies a static image of the timekeeping core and place it into the user
registers. The user can then read them without concerns over changing values causing system errors. The R bit
going from 0 to 1 causes the timekeeping capture, so the bit must be returned to 0 prior to reading again.
Battery-backed, read/write.
Reserved bits. Do not use. Should remain set to 0.
Page 14 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
By convention, any device that is sending data onto
the bus is the transmitter while the target device for
this data is the receiver. The device that is
controlling the bus is the master. The master is
responsible for generating the clock signal for all
operations. Any device on the bus that is being
controlled is a slave. The FM31L27x is always a
slave device.
Two-wire Interface
The FM31L27x employs an industry standard twowire bus that is familiar to many users. This product
is unique since it incorporates two logical devices in
one chip. Each logical device can be accessed
individually. Although monolithic, it appears to the
system software to be two separate products. One is
a memory device. It has a Slave Address (Slave ID =
1010b) that operates the same as a stand-alone
memory device. The second device is a real-time
clock and processor companion which have a unique
Slave Address (Slave ID = 1101b).
The bus protocol is controlled by transition states in
the SDA and SCL signals. There are four conditions:
Start, Stop, Data bit, and Acknowledge. The figure
below illustrates the signal conditions that specify
the four states. Detailed timing diagrams are shown
in the Electrical Specifications section.
SCL
7
SDA
Stop
(Master)
Start
(Master)
6
Data bits
(Transmitter)
0
Data bit Acknowledge
(Transmitter) (Receiver)
Figure 9. Data Transfer Protocol
Start Condition
A Start condition is indicated when the bus master
drives SDA from high to low while the SCL signal is
high. All read and write transactions begin with a
Start condition. An operation in progress can be
aborted by asserting a Start condition at any time.
Aborting an operation using the Start condition will
ready the FM31L27x for a new operation.
If the power supply drops below the specified VTP
during operation, any 2-wire transaction in progress
will be aborted and the system must issue a Start
condition prior to performing another operation.
Stop Condition
A Stop condition is indicated when the bus master
drives SDA from low to high while the SCL signal is
high. All operations must end with a Stop condition.
If an operation is pending when a stop is asserted,
the operation will be aborted. The master must have
control of SDA (not a memory read) in order to
assert a Stop condition.
Data/Address Transfer
All data transfers (including addresses) take place
while the SCL signal is high. Except under the two
conditions described above, the SDA signal should
not change while SCL is high.
Rev. 3.0
Feb. 2009
Acknowledge
The Acknowledge (ACK) takes place after the 8th
data bit has been transferred in any transaction.
During this state the transmitter must release the
SDA bus to allow the receiver to drive it. The
receiver drives the SDA signal low to acknowledge
receipt of the byte. If the receiver does not drive
SDA low, the condition is a No-Acknowledge
(NACK) and the operation is aborted.
The receiver might NACK for two distinct reasons.
First is that a byte transfer fails. In this case, the
NACK ends the current operation so that the part can
be addressed again. This allows the last byte to be
recovered in the event of a communication error.
Second and most common, the receiver does not
send an ACK to deliberately terminate an operation.
For example, during a read operation, the FM31L27x
will continue to place data onto the bus as long as the
receiver sends ACKs (and clocks). When a read
operation is complete and no more data is needed,
the receiver must NACK the last byte. If the receiver
ACKs the last byte, this will cause the FM31L27x to
attempt to drive the bus on the next clock while the
master is sending a new command such as a Stop.
Page 15 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Slave Address
The first byte that the FM31L27x expects after a
Start condition is the slave address. As shown in
figures below, the slave address contains the Slave
ID, Device Select address, and a bit that specifies if
the transaction is a read or a write.
The FM31L27x has two Slave Addresses (Slave IDs)
associated with two logical devices. To access the
memory device, bits 7-4 should be set to 1010b. The
other logical device within the FM31L27x is the
real-time clock and companion. To access this
device, bits 7-4 of the slave address should be set to
1101b. A bus transaction with this slave address will
not affect the memory in any way. The figures
below illustrate the two Slave Addresses.
The Device Select bits allow multiple devices of the
same type to reside on the 2-wire bus. The device
select bits (bits 2-1) select one of four parts on a twowire bus. They must match the corresponding value
on the external address pins in order to select the
device. Bit 0 is the read/write bit. A “1” indicates a
read operation, and a “0” indicates a write operation.
Device
Select
Slave ID
1
7
0
1
0
X
A1
A0
R/W
6
5
4
3
2
1
0
Figure 10. Slave Address - Memory
Device
Select
Slave ID
1
7
1
0
1
X
A1
A0
R/W
6
5
4
3
2
1
0
Figure 11. Slave Address – Companion
Addressing Overview – Memory
After the FM31L27x acknowledges the Slave
Address, the master can place the memory address
on the bus for a write operation. The address requires
two bytes. This is true for all members of the family.
Therefore the 4Kb and 16Kb configurations will be
addressed differently from stand alone serial
memories but the entire family will be upwardly
compatible with no software changes.
The first is the MSB (upper byte). For a given
density unused address bits are don’t cares, but
should be set to 0 to maintain upward compatibility.
Rev. 3.0
Feb. 2009
Following the MSB is the LSB (lower byte) which
contains the remaining eight address bits. The
address is latched internally. Each access causes the
latched address to be incremented automatically. The
current address is the value that is held in the latch,
either a newly written value or the address following
the last access. The current address will be held as
long as VDD > VTP or until a new value is written.
Accesses to the clock do not affect the current
memory address. Reads always use the current
address. A random read address can be loaded by
beginning a write operation as explained below.
After transmission of each data byte, just prior to the
Acknowledge, the FM31L27x increments the
internal address. This allows the next sequential byte
to be accessed with no additional addressing
externally. After the last address is reached, the
address latch will roll over to 0000h. There is no
limit to the number of bytes that can be accessed
with a single read or write operation.
Addressing Overview – RTC & Companion
The RTC and Processor Companion operate in a
similar manner to the memory, except that it uses
only one byte of address. Addresses 00h to 18h
correspond to special function registers. Attempting
to load addresses above 18h is an illegal condition;
the FM31L27x will return a NACK and abort the 2wire transaction.
Data Transfer
After the address information has been transmitted,
data transfer between the bus master and the
FM31L27x begins. For a read, the FM31L27x will
place 8 data bits on the bus then wait for an ACK
from the master. If the ACK occurs, the FM31L27x
will transfer the next byte. If the ACK is not sent, the
FM31L27x will end the read operation. For a write
operation, the FM31L27x will accept 8 data bits
from the master then send an Acknowledge. All data
transfer occurs MSB (most significant bit) first.
Memory Write Operation
All memory writes begin with a Slave Address, then
a memory address. The bus master indicates a write
operation by setting the slave address LSB to a 0.
After addressing, the bus master sends each byte of
data to the memory and the memory generates an
Acknowledge condition. Any number of sequential
bytes may be written. If the end of the address range
is reached internally, the address counter will wrap
to 0000h. Internally, the actual memory write occurs
after the 8th data bit is transferred. It will be complete
before the Acknowledge is sent. Therefore, if the
Page 16 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
user desires to abort a write without altering the
memory contents, this should be done using a Start
or Stop condition prior to the 8th data bit. The figures
By Master
Stop
Address & Data
Start
S
below illustrate a single- and multiple-writes to
memory.
Slave Address
0 A
Address MSB
A
Address LSB
A
Data Byte
A
P
By FM31L27x
Acknowledge
Figure 12. Single Byte Memory Write
Start
S
By FM31L27x
Stop
Address & Data
By Master
Slave Address
0
A
Address MSB
A
Address LSB
A
Data Byte
A
Data Byte
A
P
Acknowledge
Figure 13. Multiple Byte Memory Write
Memory Read Operation
There are two types of memory read operations. They
are current address read and selective address read. In
a current address read, the FM31L27x uses the
internal address latch to supply the address. In a
selective read, the user performs a procedure to first
set the address to a specific value.
Current Address & Sequential Read
As mentioned above the FM31L27x uses an internal
latch to supply the address for a read operation. A
current address read uses the existing value in the
address latch as a starting place for the read
operation. The system reads from the address
immediately following that of the last operation.
To perform a current address read, the bus master
supplies a slave address with the LSB set to 1. This
indicates that a read operation is requested. After
receiving the complete device address, the
FM31L27x will begin shifting data out from the
current address on the next clock. The current address
is the value held in the internal address latch.
Beginning with the current address, the bus master
can read any number of bytes. Thus, a sequential read
is simply a current address read with multiple byte
transfers. After each byte the internal address counter
will be incremented.
Rev. 3.0
Feb. 2009
Each time the bus master acknowledges a byte,
this indicates that the FM31L27x should read
out the next sequential byte.
There are four ways to terminate a read operation.
Failing to properly terminate the read will most likely
create a bus contention as the FM31L27x attempts to
read out additional data onto the bus. The four valid
methods follow.
1.
2.
3.
4.
The bus master issues a NACK in the 9th clock
cycle and a Stop in the 10th clock cycle. This is
illustrated in the diagrams below and is
preferred.
The bus master issues a NACK in the 9th clock
cycle and a Start in the 10th.
The bus master issues a Stop in the 9th clock
cycle.
The bus master issues a Start in the 9th clock
cycle.
If the internal address reaches the top of memory, it
will wrap around to 0000h on the next read cycle.
The figures below show the proper operation for
current address reads.
Selective (Random) Read
There is a simple technique that allows a user to
select a random address location as the starting point
for a read operation. This involves using the first
Page 17 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
master supplies a Slave Address with the LSB set to
1. This indicates that a read operation is requested.
After receiving the complete Slave Address, the
FM31L27x will begin shifting data out from the
current register address on the next clock. Autoincrement operates for the special function registers
as with the memory address. A current address read
for the registers look exactly like the memory except
that the device ID is different.
three bytes of a write operation to set the internal
address followed by subsequent read operations.
To perform a selective read, the bus master sends out
the slave address with the LSB set to 0. This specifies
a write operation. According to the write protocol,
the bus master then sends the address bytes that are
loaded into the internal address latch. After the
FM31L27x acknowledges the address, the bus master
issues a Start condition. This simultaneously aborts
the write operation and allows the read command to
be issued with the slave address LSB set to a 1. The
operation is now a read from the current address.
Read operations are illustrated below.
The FM31L27x contains two separate address
registers, one for the memory address and the other
for the register address. This allows the contents of
one address register to be modified without affecting
the current address of the other register. For example,
this would allow an interrupted read to the memory
while still providing fast access to an RTC register. A
subsequent memory read will then continue from the
memory address where it previously left off, without
requiring the load of a new memory address.
However, a write sequence always requires an
address to be supplied.
RTC/Companion Write Operation
All RTC and Companion writes operate in a similar
manner to memory writes. The distinction is that a
different device ID is used and only one byte address
is needed instead of two. Figure 16 illustrates a single
byte write to this device.
RTC/Companion Read Operation
As with writes, a read operation begins with the
Slave Address. To perform a register read, the bus
Start
By Master
No
Acknowledge
Address
Stop
S
Slave Address
By FM31L27x
1 A
Acknowledge
Data Byte
1
P
Data
Figure 14. Current Address Memory Read
By Master
Start
No
Acknowledge
Acknowledge
Stop
S
By FM31L27x
Address
Slave Address 1 A
Acknowledge
Data Byte
A
Data Byte
1 P
Data
Figure 15. Sequential Memory Read
Rev. 3.0
Feb. 2009
Page 18 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Start
Address
By Master
Start
No
Acknowledge
Address
Stop
S
Slave Address 0 A
Address MSB
A
By FM31L27x
Address LSB
A S
Slave Address 1 A
Data Byte
1 P
Data
Acknowledge
Figure 16. Selective (Random) Memory Read
By Master
Address & Data
Start
S
Slave Address
0 A 0 0 0
Address
By FM31L27x
Stop
A
A
Data Byte
P
Acknowledge
Figure 17. Byte Register Write
Although not required, it is recommended that A5-A7 in the Register Address byte are zeros in order to
preserve compatibility with future devices.
Addressing F-RAM Array in the FM31L27x Family
The FM31L27x family includes 256Kb, 64Kb, 16Kb, and 4Kb memory densities. The following 2-byte address field
is shown for each density.
Table 4. Two-Byte Memory Address
Part #
1st Address Byte
FM31L278
FM31L276
FM31L274
FM31L272
Rev. 3.0
Feb. 2009
x
x
x
x
A14
x
x
x
A13
x
x
x
A12
A12
x
x
A11
A11
x
x
2nd Address Byte
A10
A10
A10
x
A9
A9
A9
x
A8
A8
A8
A8
A7
A7
A7
A7
A6
A6
A6
A6
A5
A5
A5
A5
A4
A4
A4
A4
A3
A3
A3
A3
A2
A2
A2
A2
A1
A1
A1
A1
A0
A0
A0
A0
Page 19 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Electrical Specifications
Absolute Maximum Ratings
Symbol
Description
VDD
Power Supply Voltage with respect to VSS
VIN
Voltage on any signal pin with respect to VSS
VBAK
TSTG
TLEAD
VESD
Ratings
-1.0V to +5.0V
-1.0V to +5.0V * and
VIN ≤ VDD+1.0V **
-1.0V to +4.5V
-55°C to + 125°C
300° C
Backup Supply Voltage
Storage Temperature
Lead Temperature (Soldering, 10 seconds)
Electrostatic Discharge Voltage
- Human Body Model (JEDEC Std JESD22-A114-B)
- Charged Device Model (JEDEC Std JESD22-C101-A)
Package Moisture Sensitivity Level
3kV
1kV
MSL-1
* PFI input voltage must not exceed 4.5V.
** The “VIN < VDD+1.0V” restriction does not apply to the SCL and SDA inputs which do not employ a diode to VDD.
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only,
and the functional operation of the device at these or any other conditions above those listed in the operational section of this
specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability.
DC Operating Conditions (TA = -40° C to + 85° C, VDD = 2.7V to 3.6V unless otherwise specified)
Symbol
Parameter
Min
Typ
Max
VDD
Main Power Supply
2.7
3.6
IDD
VDD Supply Current
@ SCL = 100 kHz
500
@ SCL = 400 kHz
900
@ SCL = 1 MHz
1500
ISB
Standby Current
120
VBAK
IBAK
IBAKTC
VTP1
VTP2
VRST
ILI
ILO
VIL
VIH
VOL
VOH
RRST
Rev. 3.0
Feb. 2009
RTC Backup Supply Voltage
RTC Backup Supply Current
Trickle Charge Current with VBAK=0V
Fast Charge Off (FC = 0)
Fast Charge On (FC = 1)
VDD Trip Point Voltage, VTP = 0
VDD Trip Point Voltage, VTP = 1
VDD for valid /RST @ IOL = 80 µA at VOL
VBAK > VBAK min
VBAK < VBAK min
Input Leakage Current
Output Leakage Current
Input Low Voltage
All inputs except those listed below
CNT1-2 battery backed (VDD < 2.5V)
CNT1-2 (VDD > 2.5V)
Input High Voltage
All inputs except those listed below
PFI (comparator input)
CNT1-2 battery backed (VDD < 2.5V)
CNT1-2 VDD > 2.5V
Output Low Voltage (IOL = 3 mA)
Output High Voltage (IOH = -2 mA)
Pull-up Resistance for /RST Inactive
Units
V
µA
µA
µA
µA
2.0
3.0
3.75
1
V
µA
50
200
2.55
2.85
2.6
2.9
120
2500
2.70
3.00
µA
µA
V
V
±1
±1
V
V
µA
µA
-0.3
-0.3
-0.3
0.3 VDD
0.5
0.8
V
V
V
0.7 VDD
VBAK – 0.5
0.7 VDD
2.4
50
VDD + 0.3
3.75
VBAK + 0.3
VDD + 0.3
0.4
400
Continued
V
V
V
V
V
V
KΩ
»
0
1.6
Notes
7
1
2
9
4
10
5
5
6
3
3
8
Page 20 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
DC Operating Conditions, continued (TA = -40° C to + 85° C, VDD = 2.7V to 3.6V unless otherwise specified)
Symbol Parameter
Min
Typ
Max
Units
RIN
Input Resistance (pulldown)
20
A1-A0 for VIN = VIL max
KΩ
1
A1-A0 for VIN = VIH min
MΩ
VPFI
Power Fail Input Reference Voltage
1.175
1.20
1.225
V
VHYS
Power Fail Input (PFI) Hysteresis (Rising)
100
mV
Notes
Notes
1. SCL toggling between VDD-0.3V and VSS, other inputs VSS or VDD-0.3V.
2. All inputs at VSS or VDD, static. Stop command issued.
3. VIN or VOUT = VSS to VDD. Does not apply to A0, A1, or /RST pins.
4. VBAK = 3.0V, VDD < 2.4V, oscillator running, CNT1-2 at VBAK.
5. /RST is asserted low when VDD < VTP.
6. The minimum VDD to guarantee the level of /RST remains a valid VOL level.
7. Full complete operation. Supervisory circuits, RTC, etc operate to lower voltages as specified.
8. Includes /RST input detection of external reset condition to trigger driving of /RST signal by FM31L27x.
9. The VBAK trickle charger automatically regulates the maximum voltage on this pin for capacitor backup applications.
10. VBAK will source current when trickle charge is enabled (VBC bit=1), VDD > VBAK, and VBAK < VBAK max.
AC Parameters (TA = -40° C to + 85° C, VDD = 2.7V to 3.6V, CL = 100 pF unless otherwise specified)
Symbol Parameter
Min Max Min Max Min Max
fSCL
SCL Clock Frequency
0
100
0
400
0
1000
tLOW
Clock Low Period
4.7
1.3
0.6
tHIGH
Clock High Period
4.0
0.6
0.4
tAA
SCL Low to SDA Data Out Valid
3
0.9
0.55
tBUF
tHD:STA
tSU:STA
tHD:DAT
tSU:DAT
tR
tF
tSU:STO
tDH
tSP
Bus Free Before New Transmission
Start Condition Hold Time
Start Condition Setup for Repeated
Start
Data In Hold Time
Data In Setup Time
Input Rise Time
Input Fall Time
Stop Condition Setup Time
Data Output Hold (from SCL @ VIL)
Noise Suppression Time Constant
on SCL, SDA
Units
kHz
µs
µs
µs
4.7
4.0
4.7
1.3
0.6
0.6
0.5
0.25
0.25
µs
µs
µs
0
250
0
100
0
100
ns
ns
ns
ns
µs
ns
ns
1000
300
4.0
0
300
300
0.6
0
300
100
0.25
0
50
50
50
Notes
1
1
All SCL specifications as well as start and stop conditions apply to both read and write operations.
Capacitance (TA = 25° C, f=1.0 MHz, VDD = 3.0V)
Symbol
Parameter
CIO
Input/Output Capacitance
CXTAL
X1, X2 Crystal pin Capacitance
Typ
25
Max
8
-
Units
pF
pF
Notes
1
1, 2
Notes
1
This parameter is characterized but not tested.
2
The crystal attached to the X1/X2 pins must be rated as 12.5pF.
Data Retention (VDD = 2.7V to 3.6V)
Symbol
Parameter
TDR
Data Retention
@ +75°C
@ +80°C
@ +85°C
Rev. 3.0
Feb. 2009
Min
Units
45
20
10
Years
Years
Years
Notes
Page 21 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Supervisor Timing (TA = -40° C to + 85° C, VDD = 2.7V to 3.6V)
Symbol
Parameter
tRPU
/RST Active (low) after VDD>VTP
tRNR
VDD < VTP noise immunity
tVR
VDD Rise Time
tVF
VDD Fall Time
tWDP
Pulse Width of /RST for Watchdog Reset
tWDOG
Timeout of Watchdog
fCNT
Frequency of Event Counters
Min
100
10
50
100
100
tDOG
0
Max
200
25
200
2*tDOG
10
Units
ms
µs
µs/V
µs/V
ms
ms
MHz
Notes
1
1,2
1,2
3
Notes
1
This parameter is characterized but not tested.
2
Slope measured at any point on VDD waveform.
3
tDOG is the programmed time in register 0Ah, VDD > VTP and tRPU satisfied.
/RST Timing
VDD
VTP
VRST
t RNR
t RPU
RST
Rev. 3.0
Feb. 2009
Page 22 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
AC Test Conditions
Equivalent AC Load Circuit
Input Pulse Levels
Input rise and fall times
Input and output timing levels
3.6V
0.1 VDD to 0.9 VDD
10 ns
0.5 VDD
1066 Ω
Diagram Notes
All start and stop timing parameters apply to both read and write
cycles. Clock specifications are identical for read and write cycles.
Write timing parameters apply to slave address, word address, and
write data bits. Functional relationships are illustrated in the relevant
data sheet sections. These diagrams illustrate the timing parameters
only.
Output
100 pF
Read Bus Timing
tR
`
tF
t HIGH
t SP
t LOW
t SP
SCL
t SU:STA
1/fSCL
tBUF
t HD:DAT
t SU:DAT
SDA
Start
t DH
tAA
Stop Start
Acknowledge
Write Bus Timing
tHD:DAT
SCL
tHD:STA
tSU:STO
tSU:DAT
tAA
SDA
Start
Rev. 3.0
Feb. 2009
Stop Start
Acknowledge
Page 23 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Mechanical Drawing
14-pin SOIC (JEDEC Standard MS-012, Variation AB)
Recommended PCB Footprint
...
7.70
3.70
6.00 ±0.20
3.90 ±0.13
...
2.00
0.65
1.27
Pin 1
8.64 ±0.10
1.27
1.35
1.75
0.10
0.25
0.33
0.51
0.25
0.50
0.10 mm
0.19
0.25
45 °
0°- 8°
0.40
1.27
Refer to JEDEC MS-012 for complete dimensions and notes.
All dimensions in millimeters.
SOIC Package Marking Scheme
XXXXXXX-P
LLLLLLL
RIC YYWW
Legend:
XXXX= part number, P= package type (-S, -G)
LLLLLLL= lot code
RIC=Ramtron Int’l Corp, YY=year, WW=work week
Example: FM31L278, “Green”/RoHS SOIC package,
Year 2007, Work Week 36
FM31L278-G
A70023G
RIC 0736
Rev. 3.0
Feb. 2009
Page 24 of 25
FM31L278/L276/L274/L272 - 3V I2C Companion
Revision History
Revision
2.0
3.0
Rev. 3.0
Feb. 2009
Date
12/14/2007
2/9/2009
Summary
Initial release.
Changed status to Production. Added tape and reel ordering information.
Expanded data retention ratings. Added UL Recognition of trickle charger.
Page 25 of 25