规格书编号 SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF09620A21 SMD-21 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2008-6-17 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDBF09620A21 SMD-21 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDBF09620A21 SMD-21 1. SCOPE This specification shall cover the characteristics of SAW filter with the page system. HDBF09620A21 used for 2. ELECTRICAL SPECIFICATION Maximum incident power in passband Max.DC voltage between any 2 terminals Storage temperature range Operation temperature range Max.soldering profile +10dBm 30VDC -40℃ to +85℃ -40℃ to +85℃ 265℃ for 10s Electronic Characteristics Item Requirement Nominal center Frequency Insertion loss (86.0MHz~106.0MHz) Passband Bandwidth Relative attenuation 0MHz ~68.4MHz 76.8MHz 123.6MHz~162.8MHz 162.8MHz~1000MHz Amplitude ripple (86.0MHz~106.0MHz) Amplitude ripple @25℃ (86.0MHz~106.0MHz) Group delay ripple (86.0MHz~106.0MHz) www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Unit Min. Typical. Max. 20 96 9 - 12 - MHz dB MHz - dB 1.6 dB 51 40 56 35 57 45 65 40 0.9 1.2 120 E-mail:[email protected] dB 150 ns Page 3 of 8 SAW FILTER HDBF09620A21 SMD-21 Typical frequency response 3. TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDBF09620A21 SMD-21 4.DIMENSION 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in table 1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in table 1. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in table 1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER HDBF09620A21 SMD-21 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 7. Packing 7.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 7.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 7.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDBF09620A21 SMD-21 (3) Leader part and vacant position specifications. 8. TAPE SPECIFICATIONS 8.1 Tensile Strength of Carrier Tape: 4.4N/mm width 8.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 7 of 8 SAW FILTER HDBF09620A21 SMD-21 [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 7.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.5 ±0.25 0.25 ±0.05 2.20 ±0.10 5.30 ±0.10 7.30 ±0.10 [Figure 2] [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 16.8 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8