SOURCE SPC-03-ELR

155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Features
• Single 3.3V supply
• 34dB Minimum Link Budget
• DFB Laser
• 1470nm to 1610nm CWDM Wavelengths
• SFP MSA SFF-8074i Compatible
• Telcordia GR-253 OC-3/ITU-T G.957 STM-1 Compliant
• Commercial and Industrial Temperature
• Digital Diagnostic SFF-8472 Compliant
• RoHS-5 Compliant (lead exemption)
• Telcordia GR-468 Compliant
General Operation
Parameter
Symbol
Min.
Typical
Max.
Supply Voltage
Vcc
3.135
3.3
3.465
Unit
V
Total Current (-40 to -5 ºC)a
Icc
-
-
500
mA
Total Current (-5 to 85 ºC)
Icc
-
-
300
mA
Total Current Each Supply Pin
Icc
-
-
300
mA
Power Supply Noise Rejection
PSR
100
-
-
mVp-p
Operating Case Temperature (-CXX)
Top
-5
-
70
ºC
Operating Case Temperature (-TXX)
Top
-40
-
85
ºC
Storage Temperature
Tst
-40
-
85
ºC
Data Rate OC-3/STM-1
DR
-
155
-
Mbps
a) Deviation from the SFP MSA
Transmitter Specifications (Optical)
Parameter
Symbol
Min
Typical
Max
Unit
Optical Power
Pop
0
-
+5
dBm
Average Launch Power (Tx:Off)
Poff
-
-
-30
dBm
Extinction Ratio
ER
10
-
-
dB
-
-
-
SONET/SDH compliant
Eye Mask
Jgen
-
-
0.002
UI
Optical Rise Timeb
Optical Jitter Generation
tr
-
-
1000
ps
Optical Fall Timeb
tf
-
1000
ps
Wavelength
Spectral Width (20dB)
Side Mode Suppression Ratio
λ
1xx1-6.5
1xx1
1xx1+6.5
nm
∆λ
-
-
1
nm
SMSR
30
-
-
dB
-
0.5
2
dB
Dispersion Penalty (120km)
Relative Intensity Noise
RIN
-
-
-120
dB/Hz
Reflection Tolerance
rp
-
-
-24
dB
b) 20%-80% values
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Transmitter Specifications (Electrical)
Parameter
Input Differential Impedence
PECL Single-Ended Data Input Swing
TxFault_Fault
TxFault_Normal
Symbol
Min
Typical
Max
Rin
80
100
120
Unit
Ω
Vin,p-p
250
-
1200
mV
Vfault
2
-
Vcc
V
Vnormal
Vee
-
Vee+0.5
V
TxDisable_Disable
Vd
2
-
Vcc
V
TxDisable_Enable
Ven
Vee
-
Vee+0.8
V
Symbol
Min
Typical
Max
Unit
Receiver Specifications (Optical)
Parameter
c
Receive Power Low
Rsens,low
-
-36
-34
dBm
Receive Power Highc
Rsens,high
-10
-
-
dBm
Damage Threshold For Receiver
Pin,damage
4
-
-
dBm
λ
1260
-
1620
nm
-44
-
-
dBm
LOS De-Assert
-
-
-34
dBm
LOS Hysteresis
0.5
-
-
dB
Max
Unit
d
Wavelength
LOS Assert
c) at 10-10 BER,PRBS 223-1
d) Operational over 1200 to 1625 nm range
Receiver Specifications (Electrical)
Parameter
Symbol
Min
Typical
PECL Single-Ended Data Output Swing
Vout, p-p
185
-
800
mV
Data Output Rise Time
tr
-
-
1000
ps
Data Output Fall Time
tf
-
-
1000
ps
Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
ms
Tx Disable Negate Time
t_on
-
-
5
Tx Disable Assert Time
t_off
-
-
10
µs
Time To Initialize, Including Reset Of Tx Fault
t_init
-
-
300
ms
t_start_up
-
-
60
sec
t_fault
-
-
100
µs
Start-up time from <0ºC
Tx Fault Assert Time
Tx Disable To Reset
t_reset
10
-
-
µs
LOS Assert Time
t_loss_on
-
-
100
µs
LOS De-Assert Time
t_loss_off
-
-
100
µs
Serial ID Clock Rate
f_serial_clock
-
-
100
kHz
RX_LOS Voltage (High)
2
-
-
V
RX_LOS Voltage (Low)
-
-
0.8
V
VLOS fault
2
-
Vcc
V
VLOSnormal
Vee
-
Vee+0.5
V
LOS Output Voltage-Fault
LOS Output Voltage-Normal
MOD_DEF (0:2)-High
Vh
2
-
Vcc
V
MOD_DEF (0:2)-LOW
Vl
Vee
-
Vee+0.5
V
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
λ Wavelength Ordering
SPC-03-ELR-xxCDA
See table below for “XX” values
Code
λC
Unit
Code
λC
Unit
Code
λC
Unit
Code
λC
Unit
47
1471
nm
49
1491
nm
51
1511
nm
53
1531
nm
55
1551
nm
57
1571
nm
59
1591
nm
61
1611
nm
Diagnostics
Range
Accuracy
Unit
Calibration
Temperature (-CDA)
-5 to 70
±3
ºC
Internal
Tc(C)=Tad(16 bit signed twos complement)/256
Temperature (-TDA)
-40 to 85
±3
ºC
Internal
Tc(C)=Tad(16 bit signed twos complement)/256
Voltage
0 to Vcc
0.1
V
Internal
V(Volts)=Vad(16 bit unsigned integer)*0.1
Bias current
0 to 120
5
mA
External
I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset
TX Power
0 to +5
±3
dBm
External
TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer
+TX_PWRoffset
RX Power
-34 to -10
±3
dBm
External
RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4
Parameter
LUMINENTOIC.COM
Formula
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
EEPROM Serial ID
Name of Field
Vendor Name
Vendor OUI
Vendor P/N
LUMINENTOIC.COM
Description of Field
SFP Vendor name(ASCII)
IEEE vendor OUI code for LuminentOIC
Inc.
Part number in ASCII, e.g.
SPC-03-ELR-xxCDA
Address
Hex
20
4C
ASCII
L
21
55
U
22
4D
M
23
49
I
24
4E
N
25
45
E
26
4E
N
27
54
T
28
4F
O
29
49
I
30
43
C
37
00
38
06
39
B5
40
53
S
41
50
P
42
43
C
43
30
0
44
33
3
45
45
E
46
4C
L
47
52
R
48
x
x
49
x
x
50
43
C
51
44
D
52
41
A
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Pin
Function
1
VeeT
2
Notes
TX_FAULT
Open Collector
3
TX_DISABLE
Internally Pulled High
4
MOD_DEF2
Serial Data Input
5
MOD_DEF1
Serial Clock Input
6
MOD_DEF0
Internally Grounded
7
NC
Not Connected
8
LOS
Open Collector
9
VeeR
RX Ground
10
VeeR
RX Ground
11
VeeR
RX Ground
12
RXD-
RX Data Negative
13
RXD+
RX Data Positive
14
VeeR
RX GND
15
VccR
TX and RX Powera
TX and RX Powera
16
VccT
17
VeeT
TX GND
18
TXD+
TX Data Positive
19
TXD-
TX Data Negative
20
VeeT
TX GND
a) deviations from the SFP MSA
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Outline Drawing
Units in mm(inch)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Suggested Transceiver Interface
1�H
Vcc
10�F
1�H
0.1�F
VCCT
.01�F
Protocol IC
LuminentOIC
SFP
10K�
R1
TX_DISABLE
TX_DISABLE
TX_FAULT
TX_FAULT
TD +
SerDes
Laser Driver
.01�F
100�
TD VEET
.01�F
VCCR
10�F
0.1�F
RD +
Receiver Amplifier
.01�F
100�
RD -
RX_LOS
RX_LOS
Vcc
R
VEER
1
R1
R1
.01�F
EEPROM
R1
MOD_DEF 2
MOD_DEF 1
MOD_DEF 0
R1=4.7K to 10K�
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Ordering Information
Available Options:
SPC-03-ELR-xxCDA
SPC-03-ELR-xxCNA
SPC-03-ELR-xxTDA
SPC-03-ELR-xxTNA
Part Numbering Definition:
SPC - 03 - ELR - x x Temperature
Diagnostic
Revision -xx
SPC = SFP, CWDM
03 = Data Rate
ELR = Reach
xx = 1xx1 nm center wavelength
47,49,51,53,55,57,59,61
Operating Temperature
C = Commercial Temp. (-5 to 70º C)
T = Commercial Temp. (-40 to 85º C)
D = Digital Diagnostics
N = No Diagnostics
A = Design Rev.
xx = Customer Specifics
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS959-Jul2506
Rev A.1
155 Mbps CWDM SFP Transceiver
SPC-03-ELR-xx
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS959-Jul2506
Rev A.1