SOURCE SPC-4F-01

4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Features
• Single 3.3 V supply
• 10 km reach
• Supports 1.06/2.125/4.25Gb/s Fibre Channel Operation
• Compatible with 1.25Gb/s Ethernet
• 18 CWDM wavelengths, DFB Laser
• SFP MSA SFF-8074i compliant
• Digital Diagnostic SFF-8472 compliant
• Telcordia GR-468 compliant
• RoHS Compliant
General Operating
Parameter
Symbol
Min.
Typical
Max.
Unit
Supply Voltage
Vcc
3.135
3.3
3.465
V
Total Current
Icc
-
-
300
mA
Power Supply Noise Rejectiona
PSR
100
-
-
mVp-p
Operating Case Temperature
Top
-5
-
70
ºC
Storage Temperature
Tst
-40
-
85
ºC
Data Rate FC-400 Fibre Channel
DR
-
4250
-
Mbps
a) 20Hz to 155MHz
Transmitter Specifications (Optical)
Parameter
Symbol
Min
Typical
Max
Unit
Optical Power
Pop
-5
-2.5
0
dBm
Average Launch Power Of Off Tx
Poff
-
-
-45
dBm
-
-
-
Fibre Channel Compliant
-
-
130
ps
130
ps
1xxx
1xxx+6.5nm
nm
nm
Eye Mask
Optical Rise Timeb
tr
Timeb
tf
-
λ
1xxx-6.5nm
Optical Fall
Mean Wavelength
∆λ20
-
-
1
Dispersion Penalty (10 Km)c
dp
-
0.5
1
dB
Relative Intensity Noise
RIN
-
-
-120
dB/Hz
Reflection Toleranced
rp
-24
-
-
dB
Spectral Width (20dB)
b) 20%-80% values
c) Measured at BER of 1e-12, PRBS of 27-1, at eye center
d) 1 dB degradation of receiver sensitivity
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Transmitter Specifications (Electical)
Parameter
Symbol
Min
Typical
Max
Unit
Rin
80
100
120
Ω
PECL Single Ended Data Input Swing
Vin,p-p
250
-
1200
mV
TxFault_Fault
Vfault
2
-
Vcc
V
Vnormal
Vee
-
Vee+0.5
V
Vd
2
-
Vcc
V
Ven
Vee
-
Vee+0.8
V
Symbol
Min
Typical
Max
Unit
Rsens,low
-
-18
-16
dBm
Input Differential Impedence
TxFault_Normal
TxDisable_Disable
TxDisable_Enable
Receiver Specifications
Parameter
Receive Power
Lowe
Receive Power
Highe
Damage Threshold For Receiver
Wavelength
Maximum Reflectance Of Receiver
Rsens,high
-3
-
-
dBm
Pin,damage
4
-
-
dBm
λ
1200
-
1625
nm
RX_r
-
-
-27
dB
-26
-
-
dBm
LOS De-assert
-
-
-16
dBm
LOS Hysteresis
0.5
-
-
dB
LOS Assert
e) 10-12 BER, PRBS 27-1
Electrical Output
Parameter
Symbol
Min
Typical
Max
Unit
PECL Single Ended Data Output Swing
Vout, p-p
185
-
800
mV
Data Output Rise Time
tr
-
-
175
ps
Data Output Fall Time
tf
-
-
175
ps
Timing and Electrical
Parameter
Symbol
Min
Typical
Max
Unit
t_on
-
-
50
µs
Tx Disable Assert Time
t_off
-
-
10
µs
Time To Initialize, Including Reset Of Tx Fault
t_init
-
-
200
ms
Tx Disable Negate Time
Tx Fault Assert Time
t_fault
-
-
100
µs
Tx Disable To Reset
t_reset
10
-
-
µs
t_loss_on
-
-
100
µs
LOS Assert Time
LOS De-assert Time
t_loss_off
-
-
100
µs
Serial ID Clock Rate
f_serial_clock
2
-
100
KHz
2
-
Vcc
V
RX_LOS Voltage (High)
RX_LOS Voltage (Low)
LOS Output Voltage-Fault
LOS Output Voltage-Normal
-
-
0.8
V
VLOS fault
2
-
Vcc
V
VLOSnormal
Vee
-
Vee+0.5
V
MOD_DEF (0:2)-High
VH
2
-
Vcc
V
MOD_DEF (0:2)-Low
VL
Vee
-
Vee+0.5
V
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
λ Wavelength Ordering
SPC-4F-01-xxCDA
See table below for “XX” values
λc Wavelength Guide
Code
λC
Unit
Code
λC
Unit
Code
λC
Unit
27
1271
nm
39
1391
nm
51
1511
nm
29
1291
nm
41
1411
nm
53
1531
nm
31
1311
nm
43
1431
nm
55
1551
nm
33
1331
nm
45
1451
nm
57
1571
nm
35
1351
nm
47
1471
nm
59
1591
nm
37
1371
nm
49
1491
nm
61
1611
nm
Diagnostics
Parameter
Range
Accuracy
Unit
Calibration
Temperature(-CDA)
-5 to 70
±3
ºC
External
Voltage
0 to Vcc
0.1
V
External
V(Volts) = Vslope*Vad (16 bit unsigned integer) + Voffset
Bias Current
0 to 120
5
mA
External
I(mA)=Islope*Iad(16 bit unsigned integer)+Ioffset
TX Power
-5 to 0
±3 dB
dBm
External
TX_PWR(µW)=TX_PWRslope*TX_PWRad(16 bit unsigned integer
+TX_PWRoffset
RX Power
-16 to -3
±3 dB
dBm
External
RX_PWR(µW)=A0+A1*x+A2*x^2+A3*x^3+A4*x^4
LUMINENTOIC.COM
Formula
Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
EEPROM Serial ID
Name of Field
Vendor Name
Vendor OUI
Vendor PN
LUMINENTOIC.COM
Description of Field
SFP Vendor Name(ASCII)
IEEE Vendor OUI Code For LuminentOIC Inc.
Part Number in ASCII, e.g.
SPC-4F-01-xxCDA
Address
Hex
ASCII
20
4C
L
21
55
U
22
4D
M
23
49
I
24
4E
N
25
45
E
26
4E
N
27
54
T
28
4F
O
29
49
I
30
43
C
37
00
38
06
39
B5
40
53
41
50
P
42
43
C
43
34
4
44
46
F
45
30
0
46
31
1
47
x
x
48
x
x
49
43
C
50
44
D
51
41
A
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
S
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Function
Pin
Notes
1
VeeT
TX GND
2
TX_FAULT
Open Collector
3
TX_DISABLE
Internally Pulled High
4
MOD_DEF2
Serial Data Input
5
MOD_DEF1
Serial Clock Input
6
MOD_DEF0
Internally Grounded
7
NC
Not Connected
8
LOS
Open Collector
9
VeeR
RX Ground
10
VeeR
RX Ground
11
VeeR
RX Ground
12
RXD-
RX Data Negative
13
RXD+
RX Data Positive
14
VeeR
RX GND
15
VccR
RX Power
16
VccT
TX Power
17
VeeT
TX GND
18
TXD+
TX Data Positive
19
TXD-
TX Data Negative
20
VeeT
TX GND
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Outline Drawing
Units in mm(inches)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Suggested Transceiver Interface
1�H
Vcc
10�F
1�H
0.1�F
VCCT
.01�F
Protocol IC
LuminentOIC
SFP
10K�
R1
TX_DISABLE
TX_DISABLE
TX_FAULT
TX_FAULT
TD +
SerDes
Laser Driver
.01�F
100�
TD VEET
.01�F
VCCR
10�F
0.1�F
RD +
Receiver Amplifier
.01�F
100�
RD -
RX_LOS
RX_LOS
Vcc
R
VEER
1
R1
R1
.01�F
EEPROM
R1
MOD_DEF 2
MOD_DEF 1
MOD_DEF 0
R1=4.7K to 10K�
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS1663-Apr0908
Rev. A.0
4.25Gb/s Fibre Channel CWDM SFP Transceiver
SPC-4F-01-xxCDA
Ordering Information
Available Options:
SPC-4F-01-xxCDA
Part Numbering Definition:
SPC-4F
-
Reach
- xx Temperature Diagnostic Revision
SPC = CWDM SFP
4F = 4x Fibre Channel
01 = 10 km
xx = 27 to 61
Operating Temperature
C = Commercial (-5 to 70)
D = Digital Diagnostic
A = Design Revision
Warnings:
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
Legal Notes:
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at Luminent’s sole and absolute discretion. Luminent warrants performance of its
products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to
describe components only, and Luminent expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties
of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further
warranty information.
Luminent assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property
described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and Luminent makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT
intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. Luminent customers using or selling
products for use in such applications do so at their own risk and agree to fully defend and indemnify Luminent for any damages resulting from such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that Luminent is not liable for any actual,
consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
Luminent to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© Luminent, Inc. 2003
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS1663-Apr0908
Rev. A.0