SYNQOR PQ60033QMM15NKS

Technical Specification
Quarter -brick
Mega Series
w/ Baseplate
High Efficiency, Isolated DC/DC Converter, with Baseplate
This technical addendum contains additional specifications for the baseplated verison of the PowerQor Mega
Top View
series of low profile quarter-brick converters. This unit is
Bottom View
manufactured by adding an industry standard size baseplate to the non-baseplated quarter-brick converter using
standard mounting techniques. The baseplated version
PQ60xxxQMMxx
allows for optional heatsinking in severe thermal environ-
DC/DC Converter
ments or for mounting to a cold plate. Please refer to the
QMLxx specification sheets for all specifications that are
not included in this addendum.
2.32
(58.9)
MECHANICAL DIAGRAM
0.22
(5.6)
0.23
(5.8)
1.86
(47.2)
0.44
0.412 + 0.021
Side View
(11.1)
(10.46 + 0.53)
0.150 0.300 0.450
(11.43)
(3.81) (7.62)
0.600
(15.24)
0.300
(7.62)
0.600
0.019 +.013
(0.48 +0.33)
Bottom side
Clearance
Lowest
Component
See Note 12
(15.24)
Load Board
Top View
0.145
(3.68)
See Note 6
1.03
(26.2)
1.47
(37.3)
Pin farside typical
NOTES
1) M3 screws used to bolt unit’s baseplate to other surfaces (such as heatsink)
must not exceed 0.138” (3.50 mm) depth below the surface of the baseplate
2) Applied torque per screw should not exceed 6in-lb. (0.7 Nm)
3) Baseplate flatness tolerance is 0.004” (.10mm) TIR for surface
4) Pins 1-3, 5-7 are 0.040” (1.02mm) diameter with 0.080” (2.03 mm) diameter
standoff shoulders.
5) Pins 4 and 8 are 0.062” (1.57 mm) diameter with 0.100” (2.54 mm)
diameter standoff shoulders.
6) Other pin extension lengths available. Recommended pin length is 0.03”
(0.76mm) greater than the PCB thickness.
7) All Pins: Material - Copper Alloy; Finish - Tin/Lead over Nickel plate
8) Undimensioned components shown are for visual reference only.
9) Weight: 2.1 oz. (61 g) typical
10) All dimensions in inches (mm)
Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
11) Workmanship: Meets or exceeds IPC-A-610C Class II
12) UL/TUV standards require a clearance greater than 0.04” (1.02mm)
between input and output for Basic insulation. This issue should be considered
if any copper traces are on the top side of the user’s board. Note that the ferrite cores are considered part of the input/primary circuit.
Product # PQ60xxxQMMxx
Phone 1-888-567-9596
0.15
(3.8)
M3 Threaded Insert
4 Places
See Note 1 & 2
2.00
(50.8)
SPECIFICATIONS (that differ from QMLxx specs)
Weight:
add 0.94 oz. (27 g) to
non-baseplated unit weight
Max Baseplate Temp Limit:
Storage Temperature:
100°C
- 40°C to +125°C
All other specifications are identical to non-baseplated
PowerQor converters of equivalent input voltage, output
voltage and output current.
Doc.# 005-2QMMXXE Rev. D
2/9/04
Page 1
Technical Specification
Quarter -brick
Mega Series
w/ Baseplate
ATTACHING HEATSINKS
PART NUMBERING SYSTEM
Follow the guidelines given below when attaching a
heatsink to a PowerQor converter with baseplate.
The part numbering system for SynQor’s PowerQor DC/DC
converters follows the format shown in the example below.
For a complete listing of available part numbers, please
refer to the SynQor web site.
1) A thermal interface material is required to assure proper
heat transfer from the baseplate to the heatsink. Thermal
grease may be used, or materials such as Thermalloy's
Grafoil or Bergquist's HiFlow and SoftFace. Other similar
products are available from many heatsink manufacturers.
2) Use four M3 threaded machine screws for attachment.
The length of the screw will depend on the thickness of the
heatsink baseplate. The maximum permissible screw length
below the top surface of the baseplate is not to exceed
3.5mm (0.138") in order to prevent damage to any internal
components. A recommended minimum screw length to
ensure sufficient hold to the baseplate is 2.54mm (0.10”).
3) The screws should be tightened with a torque suitable to
get a tight fitting of the heatsink against the thermal interface
material and the baseplate. The applied torque per screw
should not exceed 0.7 Nm (6 in-lb).
Contact SynQor technical support for additional information.
Patents: SynQor is protected under various patents, including
but not limited to U.S. Patent numbers 5,999,417; 6,222,742
B1; 6,594,159 B2; 6,545,890 B2.
PQ 60 033 Q M M 15 N K S
Options
Output Current
Thermal Design
Performance Level
Package Size
Output Voltage
Input Voltage
Product Family
The first 12 characters comprise the base part number and
the last 3 characters indicate available options.
Selected PowerQor modules are available with a baseplate.
Before ordering basplated modules, one should consult the
factory to ensure that the specific product is available in a
baseplated version. The Mega series of single output quarter-bricks that have a baseplate should be designated with
the letter “M” as the 10th character in the full 15 character
part number. The other characters in the part number would
follow the same format as a non-baseplated unit to indicate
the desired input and output voltage, package size, performance level, rated current, enable logic, pin length and feature set.
When ordering SynQor converters, please ensure that you
use the complete 15 character part number.
Contact SynQor for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
Product # PQ60xxxQMMxx
Phone 1-888-567-9596
Warranty
SynQor offers a three (3) year limited warranty. Complete warranty
information is listed on our web site or is available upon request from
SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
Doc.# 005-2QMMXXE Rev. D
2/9/04
Page 2