Watertight 4-Wire Photoelectric Duct Smoke Detector The InnovairFlex™ Series are the only duct smoke detectors flexible enough to fit configurations from square to rectangular and everything in between. Features •NEMA Type 4 UL listed for non-hazardous indoor and outdoor applications •UV Resistant, UL listed housing and cover material •Photoelectric, integrated low-flow technology •Air velocity rating from 100 ft/min to 4,000 ft/min (0.5 m/s to 20.32 m/sec) •Versatile mounting options: square or rectangular configuration •Plug-in sensor offers superb false alarm immunity and the latest sensor technology •Broad ranges for operating temperature (–4°F to 158°F) and humidity (0% to 95% non-condensing) •Patented sampling tube installs from front or back of the detector with no tools required •Increased wiring space with a newly added ¾-inch conduit knockout •One easy-access Test/Reset button and improved LED status •Patented interconnect feature for multi-fan shutdown •New high contrast terminal designations •Built-in short circuit protection from operator wiring errors •Field selectable settings for configuring the detector •Two DPDT Form-C relay contacts •24 VAC/DC or 120VAC •Backward compatibility with existing Innovair products, including remote accessories Agency Listings The InnovairFlex D4120W watertight 4-wire photoelectric duct smoke detector is UL listed as a watertight enclosure providing protection against falling dirt, rain, windblown dust, splashing and hose directed water. D4120W duct smoke detector features a pivoting housing that fits various applications: both square and rectangular footprints mount to round or rectangular ductwork. This unit senses smoke in the most challenging conditions, operating in airflow speeds of 100 to 4,000 feet per minute, temperatures of –4°F to 158°F, and a humidity range of 0 to 95 percent (noncondensing). A plug-in sensor head offers superior false alarm immunity. These features, plus a NEMA 4 rating, allow operators to mount the detector to rooftop HVAC equipment or use the detector in other harsh environments. The new design provides the same form, fit, and wiring terminations as the standard InnovairFlex unit. Superior test and operational features added to the standard model are also available in this watertight unit. As the only watertight duct smoke detector on the market, D4120W provides unsurpassed environmental protection while simplifying installation, testing, and maintenance. This InnovairFlex duct smoke detector can be customized to meet local codes and specifications without additional wiring. The new InnovairFlex product line is compatible with all previous Innovair models, including remote test accessories. WARNING: Duct smoke detectors are NOT a substitute for open area smoke detectors; NOT a substitute for early warning detection; NOT a replacement for a building’s regular fire detection system. Refer to NFPA 72 and 90A for additional information. NOTE: To maintain the watertight properties of this duct smoke detector, watertight conduit and fittings must be used. Mount the product with the conduit holes facing downwards, if possible InnovairFlex Duct Smoke Detector Specifications Architectural/Engineering Specifications The air duct smoke detector shall be a System Sensor InnovairFlex™ D4120W Watertight NEMA4 Photoelectric Duct Smoke Detector. The detector housing shall be UL listed per UL 268A specifically for use in air handling systems. The flexible housing of the duct smoke detector fits multiple footprints from square to rectangular. The detector shall operate at air velocities of 100 feet per minute to 4000 feet per minute (0.5 to 20.32 meters/second). The unit shall be capable of controlling up to 50 air handling systems when interconnected with other detectors. The detector shall be capable of providing a trouble signal in the event that the front cover is removed. It shall be capable of local testing via magnetic switch, test button on the cover, or remote testing using the SSK451 Multi-Signaling Accessory or the RTS451KEY Remote Test Station. Terminal connections shall be of the strip and clamp method suitable for 12–18 AWG wiring. Physical Specifications Size: (Rectangular Dimensions) 14.38 in (37 cm) Length; 5 in (12.7 cm) Width; 2.5 in (6.36 cm) Depth (Square Dimensions) 7.75 in (19.7 cm) Length; 9 in (22.9 cm) Width; 2.5 in (6.35 cm) Depth Weight: 2.5 lbs (1.14 kg) Operating Temperature Range: –4° to 158°F (–20° to 70°C) Storage Temperature Range: –22°F to 158°F (–30°C to 70°C) Operating Humidity Range: 0% to 95% relative humidity non-condensing Air Duct Velocity: 100 to 4000 ft/min (0.5 m/sec to 20.3 m/sec) NEMA Enclosure Rating: Type 4 – Watertight Indoor/Outdoor Electrical Ratings Power supply voltage: 20–29 VDC 24 VAC 50–60 Hz 120 VAC 50–60 Hz Input capacitance: Reset voltage: Reset time: (with RTS451) Reset time: (by power down) Power up time: Alarm response time: Sensitivity Test: 270 μF max 3.0 VDC min .03 to 0.3 sec 0.6 sec max 35 sec max 15 sec See detector label Current Requirements: (Using No Accessories) Max. standby current: 21 mA @ 24 VDC Max. alarm current: 65 mA @ 24 VDC 270 μF max 2.0 VAC min .03 to 0.3 sec 0.6 sec max 35 sec max 15 sec See detector label N/A 10 VAC min .03 to 0.3 sec 0.6 sec max 35 sec max 15 sec See detector label 65 mA RMS @ 24 VAC 60 Hz 135 mA RMS @ 24 VAC 60 Hz 20 mA RMS @ 120 VAC 60 Hz 35 mA RMS @ 120 VAC 60 Hz Contact Ratings Alarm initiation contacts: (SPST) 2.0A @ 30 VDC (resistive) 10A @ 30 VDC; 10A @ 250 VAC; ½ HP @ 240VAC; ¼ HP @ 120VAC Note: A larm auxiliary contacts shall not be connected to initiating circuits of control panels. Use the alarm initiation contact for this purpose. Supervisory contacts: (SPDT) 2.0A @ 30 VDC (resistive); 2.0A @ 125 VAC (resistive) Alarm auxiliary contacts: (DPDT) Accessory Current Loads at 24 VDC Device Standby Trouble Alarm APA451 MHR/MHW RA400Z RTS451 RTS451KEY 12.5 mA 0 mA 0 mA 0 mA 12 mA N/A N/A N/A N/A N/A 30 mA Max 29 mA Max 12 mA Max 12 mA Max 12 mA Max SSK451 8 mA Max 16 mA Max 40 mA Max Note: Any combination of accessories may be used such that the given accessory loads are: 110mA or less at the Aux output, and 50mA or less at the Alarm output. A05-0420-000 Installing the InnovairFlex Sampling Tube The InnovairFlex sampling tube may be installed from the front or back of the detector. The tube locks securely into place and can be removed by releasing the front or rear locking tab (front locking tab shown below right). Wiring for Watertight 4-wire Duct Smoke Detector POWER INPUTS (NOTE 1) 24VAC/DC 9 POWER INPUTS (NOTE 1) 120 VAC 120 VAC 24V 9 10 10 OR OR AUXILIARY CONTACTS FOR FAN SHUTDOWN, ETC. (NOTE 2) N.C. 16 AUX A C. 6 N.O. AUXILIARY CONTACTS FOR FAN SHUTDOWN, ETC. (NOTE 2) AUX A N.C. AUX B C. N.O. N.C. 8 18 7 16 17 SUPERVISORY CONTACTS (NOTE 3) UL/FM LISTED 4-WIRE CONTROL PANEL C. 6 N.O. 17 N.C. AUX B C. N.O. 8 18 7 SUPERVISORY CONTACTS (NOTE 3) SUP C. SUP N.O. SUP C. SUP N.O. 3 14 3 14 EOL RESISTOR SPECIFIED BY PANEL MANUFACTURER + ALARM INITIATION LOOP ALARM INITIATION CONTACTS (NOTE 4) 4 ALARM C. 5 ALARM N.O. ALARM INITIATION CONTACTS (NOTE 4) FIRST DETECTOR IN THE LOOP NOTE 1: 24V Power Inputs accept a non-polarized 24VDC or 24VAC 50-60Hz. 120VAC Power Inputs accept only 120VAC 50-60Hz. Connect power source to appropriate terminals of each detector. See specifications for additional power supply information. NOTE 2: Auxiliary contacts shown in standby position. Contacts switch during alarm as indicated by arrows. Auxiliary contacts are not to be used for connection to the control panel. See specifications for contact ratings. 4 ALARM C. 5 ALARM N.O. LAST DETECTOR IN THE LOOP NOTE 3: Supervisory contacts shown in standby position. Open contacts indicate a trouble condition to the panel. See specifications for contact ratings. NOTE 4: Alarm Initiation contacts shown in standby position. Closed contacts indicate an alarm condition to the panel. See specifications for contact ratings. *Please refer to the corresponding installation manual for accessory wiring diagrams. Important Interconnect Notes • When using the interconnect feature, all interconnected units must be powered using the same independent supply. • Polarity must be maintained throughout the interconnect wiring. Connect the INT+ terminal on unit 1 to the INT+ terminal on unit 2 and so on. Similarly, connect the INT/AUX– terminal on unit 1 to the INT/AUX- terminal on unit 2 and so on. • Up to 50 D4120W units may be interconnected. • Up to 10 DH100ACDC units may be interconnected. Please note that each of the 9 DH100ACDC units interconnected may be replaced by three D4120W units. Therefore, when using the interconnect feature a single DH100ACDC can drive either 9 DH100ACDCs or 27 D4120W units. * NOTE: Alarm can be reset only at the initiating device and not at the devices interconnected. A05-0420-000 Accessories System Sensor provides system flexibility with a variety of accessories, including two remote test stations and several different means of visible and audible system annunciation. As with our duct smoke detectors, all duct smoke detector accessories are UL listed. RTS451 UL S2522 RTS451KEY UL S2522 RA400Z UL S2522 APA151 UL S4011 MHW UL S4011 MHR UL S4011 SSK451 UL S2522 SSK451 with PS24LOW strobe and PS12/24 LENSW lens Ordering Information Part No. D4120W Accessories 2D51 DST1 DST1.5 DST3 DST5 DST10 APA151 DH400 OE-1 ETX M02-04-00 Description Watertight 4-wire photoelectric low-flow duct smoke detector 4-wire conventional photoelectric sensor head Metal sampling tube duct width up to 1ft (0.3m) Metal sampling tube duct widths 1 ft to 2 ft (0.3 to 0.6 m) Metal sampling tube duct widths 2 ft to 4 ft (0.6 to 1.2 m) Metal sampling tube duct widths 4 ft to 8 ft (1.2 to 2.4 m) Metal sampling tube duct widths 8 ft to 12 ft (2.4 to 3.7 m) Remote annunciator with piezo alarm Weatherproof enclosure Metal exhaust tube duct width 1ft (0.3m) Test magnet MHR MHW P48-21-00 PS12/24SLENSC PS12/24SLENSW PS24LO PS24LOW RA400Z RTS451 RTS451KEY SSK451 3825 Ohio Avenue • St. Charles, IL 60174 Phone: 800-SENSOR2 • Fax: 630-377-6495 Mini Horn, Red Mini Horn, White End cap for metal sampling tubes Ceiling-mount “SMOKE” lens Wall-mount “SMOKE” lens Mini-Alert add-on strobe (red) Mini-Alert add-on strobe (white) Remote annunciator alarm LED Remote test station Remote test station with key lock Multi-signaling accessory ©2008 System Sensor. Product specifications subject to change without notice. Visit systemsensor.com for current product information, including the latest version of this data sheet. A05-0420-000 • 8/08 • #1837