110 WATT DC TO DC CONVERTERS DESCRIPTION PD110 SERIES The PD110 series of DC/DC converters provide up to 110 watts of continuous output power. Available in three standard input range of 10-20 VDC, 18-36 VDC and 36-72 VDC, they are ideal for a variety of applications including telecoms, portable equipment and vehicle mounted instrumentation. All units are available in compact “open PCB” or “enclosed” mechanical formats. F E ATU R E S ‧ ‧ ‧ ‧ ‧ ‧ Low cost Small size, light weight 100﹪ burn-in Overvoltage protection Overcurrent protection Three wide input ranges: 10-20 VDC, 18-36 VDC and 36-72 VDC I N P U T S P E C I F I C ATI O N S E N V I R O N M E N TA L S P E C I F I C ATI O N S Input voltage： 1 0 t o 2 0 V D C （ P D 11 0 “ L ” s e r i e s ） 1 8 t o 3 6 V D C（ P D 11 0 “ M ” s e r i e s ） 3 6 t o 7 2 V D C （ P D 11 0 “ H ” s e r i e s ） Operating temperature： St o r a g e t e m p e r a t u r e ： Relative humidity： Derating： Input current： 15A（ rms） for 12VDC 9.4A（ rms） for 24VDC 4.7A（ rms） for 48VDC 0℃ to +70℃ -40℃ to +85℃ 5﹪ to 95﹪ non-condensing Derate from 100﹪ at +50℃ linearly to 50﹪ at +70℃ OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Output voltage/current： See rating chart Switching frequency： 50KHz ±5KHz Total output power： 110 watts maximum Efficiency： 70﹪ minimum at full load Ripple and noise： 1﹪ peak to peak max. Line regulation： ±0.5﹪ maximum at full load Overvoltage protection： set at 112 - 132﹪ of its nominal output voltage Withstand voltage： 1000VDC from input to output MTBF： Overcurrent protection： All outputs protected to short circuit conditions 400,000 hours minimum at full load at 25℃ ambient, calculated per MIL-HDBK-217F Temperature coefficient： All outputs ±0.04﹪ /℃ maximum Transient response： Maximum excursion of 4﹪ or better on all models, recovering to 1﹪ of final value within 500us after a 25﹪ step load change Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● [email protected] ● www.TRUMPower.com PD110 SERIES DC TO DC CONVERTERS OUTPUT VOLTAGE/CURRENT RATING CHART (3) Model PD110-10 PD110-12 PD110-13 PD110-14 PD110-16 PD110-23 PD110-31 PD110-32 PD110-40 PD110-41 PD110-42 PD110-45-1 PD110-45-2 PD110-46 Output #1 Vnom. Imin. Imax. Tol. 5V 0A 22A 3% 12V 0A 9.0A 2% 15V 0A 7.5A 2% 24V 0A 4.5A 2% 30V 0A 3.6A 2% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% +5V 0.8A 10A 3% Vnom. +12V +12V +15V +12V +15V +12V +12V +24V +15V Output #2(1) Imin. Imax. Ipeak (N/A) (N/A) (N/A) (N/A) (N/A) 0A 5A 9.0A 0A 5A 9.0A 0A 4A 7.5A 0A 5A 9.0A 0A 4A 7.5A 0A 5A 9.0A 0A 5A 9.0A 0A 3A 5.0A 0A 4A 7.5A Tol. Vnom. 3% 3% 3% 3% 3% 3% 3% 3% 3% -12V -15V -12V -15V -12V -12V -12V -15V Output #3 Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A 0A 1A Tol. 4% 4% 4% 4% 4% 4% 4% 4% Output #4 Vnom. Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) -5V 0A 1A +24V 0A 1A +12V 0A 1A +24V 0A 1.5A +12V 0A 1A -5V 0A 1A Tol. 4% 4% 4% 10% 4% 4% Maximum Output Power (2) 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W Notes: (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. (2) PD110”M” & “H” series are suitable only for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. PD110”L” series are suitable only for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. (3) Suffix codes for input range, mechanical format and connector are as follows. PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L=10-20 VDC, M=18-36 VDC, H=36-72 VDC), “X4” is the mechanical format (A=open PCB, B=L-bracket, C=enclosed) and “X5” is the input and output connector code (Blank=Molex KK type, T=miniature terminal block), e.g. PD110-31MCT (18-36 VDC input range, enclosed format and miniature terminal blocks). MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal. 4. Miniature terminal blocks: Input terminals allow wires up to 2mm2 (AWG #14). Output terminals allow wires up to 2mm2 (AWG #14). 5. Weight: 640grams (PCB format) 6. See the mechanical details of L-bracket and enclosed formats in page 7-2. PIN CHART MODEL MINI. TERMINAL MOLEX CONNECTOR PD110-10 PD110-13 PD110-16 PD110-23 PD110-12 PD110-14 PD110-31 PD110-32 1 2 3 4 1,2,3 4,5 6,7 8,9 10 11 12 13 OUTPUT #1 RETURN RETURN OUTPUT #1 N.C. N.C. KEY N.C. N.C. N.C. KEY N.C. N.C. OUTPUT #3 KEY N.C. N.C. OUTPUT #3 KEY OUTPUT #4 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 PD110-40 PD110-41 OUTPUT COMMON COMMON OUTPUT PD110-42 PD110-45-1 #1 RETURN RETURN #2 PD110-45-2 PD110-46 5 Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● [email protected] ● www.TRUMPower.com 6