TRUMPower 110 WATT DC/DC CONVERTERS D ESCR IP TI ON TD110 SERIES The TD110 series of DC/DC converters provide up to 110 watts of continuous output power. Available in three standard input range of 10-20 VDC, 18-36 VDC and 36-72 VDC, they are ideal for a variety of applications including telecoms, portable equipment and vehicle mounted instrumentation. All units are available in compact “open PCB” or “enclosed” mechanical formats. F EATU R ES ‧ ‧ ‧ ‧ ‧ ‧ Low cost Small size, light weight 100﹪ burn-in Overvoltage protection Overcurrent protection Three wide input ranges: 10-20 VDC, 18-36 VDC and 36-72 VDC I NPU T SP EC IF ICAT ION S Input voltage： 1 0 t o 2 0 V D C （ T D 11 0 “ L ” s e r i e s ） 1 8 t o 3 6 V D C（ T D 11 0 “ M ” s e r i e s ） 3 6 t o 7 2 V D C（ T D 11 0 “ H ” s e r i e s ） Input current： 15A for 12VDC 9.4A for 24VDC 4.7A for 48VDC ENVIR ONM ENTA L SPEC IFICAT IONS Operating temperature： St o r a g e t e m p e r a t u r e ： Relative humidity： Derating： 0℃ to +70℃ -40℃ to +85℃ 5﹪ to 95﹪ non-condensing Derate from 100﹪ at +50℃ linearly to 50﹪ at +70℃ OUTPUT SPECIFICATIONS Output voltage/current： See rating chart Total output power： 110 watts maximum Ripple and noise： 1﹪ peak to peak max. Overvoltage protection： set at 112-132﹪ of its nominal output voltage Overcurrent protection： All outputs protected to short circuit conditions Temperature coefficient： Transient response： All outputs ±0.04﹪ /℃ maximum Maximum excursion of 4﹪ or better on all models, recovering to 1﹪ of final value within 500us after a 25﹪ step load change GENERAL SPECIFICATIONS Switching frequency： 50KHz ±5KHz Efficiency： 70﹪ minimum at full load Line regulation： ±0.5﹪ maximum at full load Withstand voltage： 1000VDC from input to output MTBF： 400,000 hours minimum at full load at 25℃ ambient, calculated per MIL-HDBK-217F Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● Fax: 408-988-6622 ● email: [email protected] ● Website: www.TRUMPower.com TD110 SERIES DC/DC CONVERTERS OUTPUT VOLTAGE/CURRENT RATING CHART Product # (3) TD110-S05 TD110-S12 TD110-S15 TD110-S24 TD110-S30 TD110-D23 TD110-T31 TD110-T32 TD110-Q40 TD110-Q41 TD110-Q42 TD110-Q45-1 TD110-Q45-2 TD110-Q46 Output #1 Vnom. Imin. Imax. 5V 0A 22A 12V 0A 9.0A 15V 0A 7.5A 24V 0A 4.5A 30V 0A 3.6A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A +5V 0.8A 10A Tol. 3% 2% 2% 2% 2% 3% 3% 3% 3% 3% 3% 3% 3% 3% Vnom. +12V +12V +15V +12V +15V +12V +12V +24V +15V Output #2 (1) Imin. Imax. Ipeak Tol. (N/A) (N/A) (N/A) (N/A) (N/A) 0A 5A 9.0A 3% 0A 5A 9.0A 3% 0A 4A 7.5A 3% 0A 5A 9.0A 3% 0A 4A 7.5A 3% 0A 5A 9.0A 3% 0A 5A 9.0A 3% 0A 3A 5.0A 3% 0A 4A 7.5A 3% Output #3 Vnom. Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) -12V 0A 1A -15V 0A 1A -12V 0A 1A -15V 0A 1A -12V 0A 1A -12V 0A 1A -12V 0A 1A -15V 0A 1A Tol. Vnom. 4% 4% 4% 4% 4% 4% 4% 4% -5V +24V +12V +24V +12V -5V Output #4 Imin. Imax. (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) (N/A) 0A 1A 0A 1A 0A 1A 0A 1.5A 0A 1A 0A 1A Tol. 4% 4% 4% 10% 4% 4% Maximum Output Power (2) 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W 110W Notes: (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. (2) TD110”M” & “H” series are suitable only for 110 watts maximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. TD110”L” series are suitable only for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. (3) Suffix codes for input range, mechanical format and connector are as follows. TD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L=10-20 VDC, M=18-36 VDC, H=36-72 VDC), “X4” is the mechanical format (Blank=PCB, B=L-bracket, C=enclosed) and “X5” is the input and output connector code (Blank=Molex KK type, T=miniature terminal block), e.g. TD110-31MCT (18-36 VDC input range, enclosed format and miniature terminal blocks). MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal. 4. Miniature terminal blocks: Input terminals allow wires up to 2mm2 (AWG #14). Output terminals allow wires up to 2mm2 (AWG #14). 5. Weight: 640grams (PCB format) 6. Refer to the last page for mechanical details on L-bracket and enclosed formats. PIN CHART MINI. TERMINAL 1 2 3 4 5 6 1,2,3 4,5 6,7 8,9 10 11 12 13 OUTPUT #1 RETURN RETURN OUTPUT #1 N.C. N.C. KEY N.C. N.C. N.C. KEY N.C. N.C. OUTPUT #3 KEY N.C. N.C. OUTPUT #3 KEY OUTPUT #4 MOLEX CONNECTOR PRODUCT NO. TD110-S05 TD110-S15 TD110-S30 TD110-D23 TD110-12 TD110-24 TD110-T31 TD110-T32 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 OUTPUT COMMON COMMON OUTPUT #1 RETURN RETURN #2 TD110-Q40 TD110-Q41 OUTPUT COMMON COMMON OUTPUT TD110-Q42 TD110-Q45-1 #1 RETURN RETURN #2 TD110-Q45-2 TD110-Q46 Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● [email protected] ● www.TRUMPower.com L-Bracket and Enclosed Formats of TD110 Series Unit: inch [mm] Tolerance: 0.02 [0.5]