A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Full Color Chip LED Lamps Part Number: AL-HD1G6B433T Package outlines & Re-flow Profile Reflow Temp/Time 1 3 2 4 Soldering iron Basic spec is U 5sec when 260℃. If temperature is higher, time should be shorter (+10℃Æ -1sec ).Power dissipation of iron should be smaller than 15W, and temperatures should be controllable .Surface temperature of the device should be under 230℃ . ITEM MATERIALS Resin (mold) Epoxy Lens color Water Clear Printed circuit board BT GaAlAs/GaAs R1 G3 Dice 2 InGaN Super Red B4 For Reflow Soldering InGaN Emitted color Green Super Blue NOTES: 1. All dimensions are in millimeters (inches). 2. Tolerances are ±0.1mm (0.004inch) unless otherwise noted. 3. Polarity referring onto the cathode mark is reversed on the red. 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HD1G6B433T ELECTRO-OPTICAL CHARACTERISTICS Parameter Forward voltage Luminous intensity Wavelength Spectral Line Half-Width Peak pulsing current (1/10 duty f=1kHz) Power Dissipation Emitted Color Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue Super Red Green Super Blue (TA=25℃) Value Test Symbol Condition MIN. TYP. MAX. IF=20mA VF IF=20mA IV λp IF=20mA λd − − − 12.3 94 28 − − − 638 520 465 − − − 1.8 3.4 3.5 25 180 50 660 525 470 − − − 20 30 30 V mcd nm IF=20mA △λ IF=20mA IFP 100 mA PD 60 120 120 mW IF=20mA Absolute maximum ratings Parameter 2.6 3.8 4.0 − − − − − − 648 530 475 − − − Unit nm (TA=25℃) Symbol Value Unit 2θ1/2 120 Deg Forward current IF 30 mA Reverse voltage VR 5 V Reverse current IR 100 µA Operating temperature range Top -25 ~+80 ℃ Storage temperature range Tstg -30 ~+85 ℃ Viewing angle at 50% Iv 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HD1G6B433T Test items and results of reliability ＊Refer to reliability test standard specification for in this line. 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HD1G6B433T Typical Electro-Optical Characteristics Curves 2007/6/13 A-BRIGHT A-BRIGHT INDUSTRIAL CO., LTD. SURFACE MOUNT LED LAMPS Part Number: AL-HD1G6B433T Precautions For Use 1. Over-current proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment︰60±5℃ for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds within once in less than soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 2007/6/13