ACT ACTF9001

Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
The ACTF9001/1220.0/QCC8B is a low-loss, compact and economical” surface wave
acoustic” (SAW) RF filter in an SMD QCC8B package for Digital Set Top Box
applications.
1.Package Dimension (QCC8B)
2.
Pin
Configuration
1,2
Input
5,6
Output
3,7
To be grounded
4,8
Case Ground
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
1.00
D
1.50
B
1.27
E
3.80
C
0.60
F
3.80
3. Matching Circuit
No matching network required for operation at 200 Ω
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
1 OF 4
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
4. Typical Frequency Response
5.Performance
5-1.Maximum ratings
Rating
Value
Units
Input Power Level
0
dBm
DC Voltage
0
V
Operable temperature range
-40 to +85
°C
Storage temperature range
-40 to +85
°C
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
2 OF 4
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
5-2.Electronic characteristics
Operating temperature range:
Terminating source impedance:
Terminating load impedance:
T = -40 °c… +85 °c
ZS= 200 Ω
ZL = 200 Ω
Characteristic
Min.
Centre Frequency
fC
Maximum insertion Loss (±4MHz)
IL max
Ripple in passband (±4MHz)
Attenuation
Group delay ripple
Aperture 500 kHz
Typ.
1220.0
∆
α
α
rel
3.5
Units
MHz
4.7
5.8
dB
0.8
1.5
dB
500.00 …. fc–91.00 MHz
fc–91.00 …. f c–85.00 MHz
50.0
60.0
50.0
60.0
fc–76.00 …. f c–68.00 MHz
46.0
55.0
fc–88.00 MHz
50.0
60.0
fc–72.00 MHz
48.0
58.0
fc–44.00 MHz
50.0
60.0
fc–36.00 MHz
46.0
52.0
fc+70.00 …. 2000.00 MHz
50.0
55.0
∆
Max.
dB
τ
1216.00 …… 1224.00 MHz
15
ns
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
3 OF 4
Issue : 1 C1
Date : SEPT 04
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: info@actcrystals.com
5-3.Electronic characteristics
Operating temperature range:
Terminating source impedance:
Terminating load impedance:
T = 20 °c … 70 °c
ZS= 200 Ω
ZL = 200 Ω
Characteristic
Min.
Centre Frequency
fC
Minimum Insertion Loss
Units
MHz
IL min
3.5
1210.00 …. 1229.00 MHz
Relative attenuation ( relative to IL min)
4.5
5.8
dB
1.0
3.0
dB
α
∆
Ripple in passband
Aperture 500 kHz
Max.
1220.0
1210.00 …. 1229.00 MHz
Group delay ripple
Typ.
α
rel
500.00 …. f C–91.00 MHz
46.0
56.0
fC–91.00 …. fC–85.00 MHz
46.0
56.0
fC–76.00 …. fC–68.00 MHz
42.0
51.0
fC–88.00 MHz
46.0
56.0
fC–72.00 MHz
44.0
54.0
fC–44.00 MHz
46.0
56.0
fC–36.00 MHz
42.0
48.0
fC +70.00 …. 2000.00 MHz
46.0
51.0
∆
dB
τ
1210.00 …… 1229.00 MHz
40
ns
iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling!
1.
2.
3.
4.
5.
6.
The frequency f C is defined as the midpoint between the 3dB frequencies.
Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is
connected to a 50 Ω test system with VSWR≤1.2:1. The test fixture L and C are adjusted for minimum insertion
loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on
the impedance matching component values and quality.
Unless noted otherwise, specifications apply over the entire specified operating temperature range.
The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
All equipment designs utilizing this product must be approved by the appropriate government agency prior to
manufacture or sale.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered - Registration number 6830/2
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
4 OF 4
Issue : 1 C1
Date : SEPT 04